The GRO library provides two modes to reassemble packets. Currently, the
csum forwarding engine has supported to use the lightweight mode to
reassemble TCP/IPv4 packets. This patch introduces the heavyweight mode
for TCP/IPv4 GRO in the csum forwarding engine.
With the command "set port <port_id> gro on|off", users can enable
TCP/IPv4 GRO for a given port. With the command "set gro flush <cycles>",
users can determine when the GROed TCP/IPv4 packets are flushed from
reassembly tables. With the command "show port <port_id> gro", users can
display GRO configuration.
The GRO library doesn't re-calculate checksums for merged packets. If
users want the merged packets to have correct IP and TCP checksums,
please select HW IP checksum calculation and HW TCP checksum calculation
for the port which the merged packets are transmitted to.
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
Add new commands to manipulate with dynamic flow type to
pctype mapping table in i40e PMD.
Commands allow to print table, modify it and reset to default value.
Signed-off-by: Kirill Rybalchenko <kirill.rybalchenko@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
There were mising :: so file was parsed in wrong way
Fixes: c735b831b0c1 ("app/testpmd: add cmd for dedicated LACP Rx/Tx queues")
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
This patch enables TCP/IPv4 GRO library in csum forwarding engine.
By default, GRO is turned off. Users can use command "gro (on|off)
(port_id)" to enable or disable GRO for a given port. If a port is
enabled GRO, all TCP/IPv4 packets received from the port are performed
GRO. Besides, users can set max flow number and packets number per-flow
by command "gro set (max_flow_num) (max_item_num_per_flow) (port_id)".
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Reviewed-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
Add new command to support enable/disable of dedicated Tx/Rx queue on
each slave of a bond device for LACP control plane traffic.
set bonding lacp dedicated_queues <port_id> [enable|disable]
When enabled this option creates dedicated queues on each slave device
for LACP control plane traffic. This removes the need to filter control
plane packets in the data path.
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
New command 'ddp del (port) (profile_path)' removes previously
loaded profile and deletes it from the list of the loaded profiles.
Signed-off-by: Andrey Chilikin <andrey.chilikin@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
This patch demonstrates how to get information about dynamic device
personalization (DDP) profile.
Command 'ddp get info (path_to_profile)' extracts and prints
information about the given profile.
Signed-off-by: Andrey Chilikin <andrey.chilikin@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Add new meta pattern item RTE_FLOW_TYPE_ITEM_FUZZY in flow API.
This is for device that support fuzzy match option.
Usually a fuzzy match is fast but the cost is accuracy.
i.e. Signature Match only match pattern's hash value, but it is
possible that two different patterns have the same hash value.
Matching accuracy level can be configured by subfield threshold.
Driver can divide the range of threshold and map to different
accuracy levels that device support.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Isolated mode can be requested by applications on individual ports to avoid
ingress traffic outside of the flow rules they define.
Besides making ingress more deterministic, it allows PMDs to safely reuse
resources otherwise assigned to handle the remaining traffic, such as
global RSS configuration settings, VLAN filters, MAC address entries,
legacy filter API rules and so on in order to expand the set of possible
flow rule types.
To minimize code complexity, PMDs implementing this mode may provide
partial (or even no) support for flow rules when not enabled (e.g. no
priorities, no RSS action). Applications written to use the flow API are
therefore encouraged to enable it.
Once effective, leaving isolated mode may not be possible depending on PMD
implementation.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Stop port before enabling QinQ.
Add commands to set inner and outer TPID's and start port.
Remove TPID's from flow validate and and flow create commands.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Adds support to testpmd to load a set of cmdline CLI commands at runtime.
This can be helpful when needing to cut-n-paste many commands where
cut-n-paste may not be practical.
testpmd> load /home/ubuntu/somefile.txt
Signed-off-by: Allain Legacy <allain.legacy@windriver.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Adds support to testpmd to load a set of cmdline CLI commands at startup.
This can be helpful when needing to cut-n-paste many commands each time
testpmd is restarted. This option will work in both interactive and
non-interactive modes.
./testpmd -n4 -c3 ... -- --cmdline-file=/home/ubuntu/somefile.txt
Signed-off-by: Allain Legacy <allain.legacy@windriver.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
E-Tag and NVGRE pattern items have been added hastily without updating
documentation nor testpmd.
This commit also adds default masks for these items based on the ixgbe
implementation.
Fixes: 99e7003831c3 ("net/ixgbe: parse L2 tunnel filter")
Cc: stable@dpdk.org
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add information on validating and creating QinQ flow rules to
the flow rules management section of the Testpmd User Guide.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Since VF can not disable/enable HW CRC strip for non-DPDK PF drivers,
and kernel driver almost default enable that feature, if disable it in
app's rxmode, VF driver will report the VF launch failure. So this
patch default to enable HW CRC strip to let VF launch successful.
Cc: stable@dpdk.org
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Add a CLI in testpmd to test the TC min bandwidth
setting.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch exposes the following item fields through the flow command:
- MPLS label
- GRE protocol
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Add a CLI to set some TCs' strict link priority mode
on a physical port.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Add CLI to set a specific TC's max bandwidth
on a specific VF from PF.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Add CLI to set TCs' min bandwidth on a specific VF
from PF.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Add CLI to set a specific VF's TX max bandwidth
from PF.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Add two new commands "show port cap <port>" and "show
port cap all" to display what offload capabilities supported
in ports. It will not only display all the capabilities of
the port, but also the enabling condition for each capability
in the running time.
Signed-off-by: Qiming Yang <qiming.yang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
command is: set vf vlan tag port_id vf_id on|off
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Vincent Jardin <vincent.jardin@6wind.com>
Add command to call rte_pmd_i40e_set_vf_broadcast.
Add set vf broadcast in testpmd_funcs.rst file.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Vincent Jardin <vincent.jardin@6wind.com>
Add testpmd CLI to set VF multicast promiscuous mode on i40e.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Vincent Jardin <vincent.jardin@6wind.com>
Add testpmd CLI to set VF unicast promiscuous mode on i40e.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Vincent Jardin <vincent.jardin@6wind.com>
This patch fixes a trivial typo in testpmd application guide.
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Below MACsec offload commands are added:
- set macsec offload <port_id> on encrypt on|off replay-protect on|off
- set macsec offload <port_id> off
- set macsec sc tx|rx <port_id> <mac> <pi>
- set macsec sa tx|rx <port_id> <idx> <an> <pn> <key>
Also update the testpmd user guide.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Rename tools/ into usertools/ to differentiate from buildtools/
and devtools/ while making clear these scripts are part of
DPDK runtime.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Tested-by: Ferruh Yigit <ferruh.yigit@intel.com>
This commit exposes the following item fields through the flow command:
- VLAN priority code point, drop eligible indicator and VLAN identifier
(all part of TCI).
- IPv4 type of service, time to live and protocol.
- IPv6 traffic class, flow label, next header and hop limit.
- SCTP tag and checksum.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Document syntax, interaction with rte_flow and provide usage examples.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Olga Shern <olgas@mellanox.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
The final parameter to rte_pmd_ixgbe_set_vf_vlan_insert is uint8_t
and treated as a binary flag when it needs to be a uint16_t
and treated as a VLAN id. The data sheet (sect 8.2.3.27.13) describes
the right most 16 bits as the VLAN id that is to be inserted; the
16.11 code is accepting only a 1 or 0 thus effectively only
allowing the VLAN id 1 to be inserted (0 disables the insertion
setting).
This patch changes the final parm name to represent the data that
is being accepted (vlan_id), changes the type to permit all valid
VLAN ids, and validates the parameter based on the range of 0 to
4095. Corresponding changes to prototype and documentation in the
.h file.
Fixes: 49e248223e9f71 ("net/ixgbe: add API for VF management")
Signed-off-by: E. Scott Daniels <daniels@research.att.com>
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
In mac-vlan mode, MAC address mask is not supported by HW.
The MAC address mask should not be set in mac-vlan mode.
Remove this parameter from the CLI. Remove MAC address
from mask print too.
Fixes: 53b2bb9b7ea7 ("app/testpmd: new flow director commands")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
add test for set vf vlan anti spoof
add test for set vf mac anti spoof
add test for set vf vlan stripq
add test for set vf vlan insert
add test for set tx loopback
add test for set all queues drop enable bit
add test for set vf split drop enable bit
add test for set vf mac address
add new APIs to testpmd help command.
add new APIs to the testpmd guide
Modify Makefile, add library rte_pmd_ixgbe to _LDLIBS-y.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Explain default testpmd behavior in mac fwd mode to remove
amiguity/confusion regarding user's ability to specify Ethernet
addresses.
Signed-off-by: Mark Kavanagh <mark.b.kavanagh@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Update the testpmd user guide with instructions for retrieving extended
NIC statistics.
Signed-off-by: Maryam Tahhan <maryam.tahhan@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Support to configure 25G and 50G speeds is missing from testpmd.
This patch also updates the testpmd user guide accordingly.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
"flowgen" forwarding mode has fixed packet size (300).
Let it re-use --txpkts option for specifying generated packet size.
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
The vdev eth_bond has been renamed to net_bond.
testpmd is creating a bonding device with the old prefix.
It is changed for consistency.
The script test-null.sh was failing because using the old name
for the null vdev.
Fixes also the bonding and testpmd doc.
Fixes: 2f45703c17ac ("drivers: make driver names consistent")
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
The following tools may be installed system-wide.
It may be cleaner and more convenient to find them with the same
dpdk- prefix (especially for autocompletion).
Moreover, the script dpdk_nic_bind.py deserves a new name because it is
not restricted to NICs and can be used for e.g. crypto.
These files are renamed:
pmdinfogen -> dpdk-pmdinfogen
pmdinfo.py -> dpdk-pmdinfo.py
dpdk_pdump -> dpdk-pdump
dpdk_proc_info -> dpdk-procinfo
dpdk_nic_bind.py -> dpdk-devbind.py
setup.sh -> dpdk-setup.sh
The tools pmdinfogen, pmdinfo.py and dpdk_pdump are new in 16.07.
The scripts dpdk_nic_bind.py and setup.sh may have been used with
previous releases by end users. That's why a symbolic link still
provide the old name in the installed tools directory.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
- added VXLAN, GENEVE and NVGRE tunnel flow types
- added PORT flow type for accounting physical/virtual
port or channel number in flow creation
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
This patch enables configurable tx_first burst number.
Use "start tx_first (burst_num)" to specify how many bursts of packets to
be sent before forwarding start, or "start tx_first" like before for the
default 1 burst send.
Signed-off-by: Zhihong Wang <zhihong.wang@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
