VMDq is not supported yet, so remove the unused code.
Fixes: d51867db65 ("net/hns3: add initialization")
Fixes: 1265b5372d ("net/hns3: add some definitions for data structure and macro")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch deletes some unused capabilities, include:
1. Delete some unused firmware capabilities definition, which are:
UDP_GSO, ATR, INT_QL, SIMPLE_BD, TX_PUSH, FEC and PAUSE.
2. Delete some unused driver capabilities definition, which are:
UDP_GSO, TX_PUSH.
3. Also redefine HNS3_DEV_SUPPORT_* as enum type, and change some of
the values. Note: the HNS3_DEV_SUPPORT_* values is used only inside
the driver, so it's safe to change the values.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Kunpeng 930 uses a new RAS exception reporting solution.
The reset type and exception status are reported through
firmware. The driver modifies the corresponding code to
adapt to the new solution.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports link speed auto-negotiation for PF. If the
device supports auto-negotiation, the device negotiates with
the link partner at all speeds supported by the device.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the speed of fiber port is obtained by using the default
query type of HNS3_OPC_GET_SFP_INFO opcode. In this way, only
the speed of the optical module can be obtained. In fact, the opcode
also supports an active query type, which is a channel for obtaining
information such as the speed, the supported speed, auto-negotiation
capability, and FEC mode. This patch changes the query type of the
opcode from the default query type to the active query type to obtain
the supported speed of fiber port.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The bit(5) of supported, advertising and lp_advertising for copper
PHYs obtained from the firmware indicates 1000M full-duplex. This
speed capability bit is missing in the current codes.
Fixes: 2e4859f3b3 ("net/hns3: support PF device with copper PHYs")
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The type of return value of hns3_cmd_send is int, some function declare
the return value as hns3_cmd_status.
This patch fix the incorrect use of the enum hns3_cmd_status.
Fixes: 737f30e1c3 ("net/hns3: support command interface with firmware")
Fixes: 02a7b55657 ("net/hns3: support Rx interrupt")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch updates copyright date for hns3 PMD files.
Fixes: 565829db8b ("net/hns3: add build and doc infrastructure")
Fixes: 952ebacce4 ("net/hns3: support SVE Rx")
Fixes: e31f123db0 ("net/hns3: support NEON Tx")
Fixes: c09c7847d8 ("net/hns3: support traffic management")
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
According to the suggestion of our legal department,
to standardize the copyright license of our code to
avoid potential copyright risks, we make a unified
modification to the "Hisilicon", which was nonstandard,
in the main modules we maintain.
We change it to "HiSilicon", which is consistent with
the terms used on the following official website:
https://www.hisilicon.com/en/terms-of-use.
Fixes: 565829db8b ("net/hns3: add build and doc infrastructure")
Fixes: 952ebacce4 ("net/hns3: support SVE Rx")
Fixes: e31f123db0 ("net/hns3: support NEON Tx")
Fixes: c09c7847d8 ("net/hns3: support traffic management")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the queue reset process needs to be performed one by one,
which is inefficient. However, the queues reset in the same function is
almost at the same stage. To optimize the queue reset process, a new
function has been added to the firmware command HNS3_OPC_CFG_RST_TRIGGER
to reset all queues in the same function at a time. And the related
queue reset MBX message is adjusted in the same way too.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch added function level imissed stats for PF and VF. In
Kunpeng920, imissed is supported, only including RPU drop stats in PF.
In kunpeng930, imissed is supported,including RPU drop stats and SSU
drop stats in PF.
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
TNL is the abbreviation of tunnel, which means port
here. MAC TNL interrupt indicates the MAC status
report of the network port, which will be generated
when the MAC status changes.
This patch enables MAC TNL interrupt reporting, and
queries and prints the corresponding MAC status when
the interrupt is received, then clear the MAC interrupt
status. Because this interrupt uses the same interrupt
as RAS, the interrupt log is adjusted.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, the driver get packet type by parse the
L3_ID/L4_ID/OL3_ID/OL4_ID from Rx descriptor and then lookup multiple
tables, it's time consuming.
Now Kunpeng930 support advanced RXD layout, which:
1. Combine OL3_ID/OL4_ID to 8bit PTYPE filed, so the driver get packet
type by lookup only one table. Note: L3_ID/L4_ID become reserved
fields.
2. The 1588 timestamp located at Rx descriptor instead of query from
firmware.
3. The L3E/L4E/OL3E/OL4E will be zero when L3L4P is zero, so driver
could optimize the good checksum calculations (when L3E/L4E is zero
then mark PKT_RX_IP_CKSUM_GOOD/PKT_RX_L4_CKSUM_GOOD).
Considering compatibility, the firmware will report capability of
RXD advanced layout, the driver will identify and enable it by default.
This patch only provides basic function: identify and enable the RXD
advanced layout, and lookup ptype table if supported.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The normal operation of devices with copper phys depends on the
initialization and configuration of the PHY chip. The task of
driving the PHY chip is implemented in some firmware versions.
If firmware supports the phy driver, it will report a capability
flag to driver in probing process. The driver determines whether
to support PF device with copper phys based on the capability bit.
If supported, the driver set a flag indicating that the firmware
takes over the PHY, and then the firmware initializes the PHY.
This patch supports the query of link status and link info, and
existing basic features for PF device with copper phys.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch implement Rx imissed stats by querying cmdq.
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch makes more registers dumped in the dump_reg API to help
locate the fault.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch add support for dumping module EEPROM.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
There are two scenarios that command queue uninit performed
concurrently with the firmware command: asynchronous command
and timeout command.
For asynchronous command, if a large number of functions send
commands, these commands may need to be queued to wait for
firmware processing. If a function is uninited suddenly, CMDQ
clearing and firmware processing may be performed concurrently.
For timeout command, if the command failed due to busy scheduling
of firmware, this command will be processed in the next scheduling.
And this may lead to concurrency.
The preceding concurrency may lead to a firmware exceptions.
This patch add a waiting time to ensure the firmware complete the
processing of left over command when PMD uninit.
Fixes: 737f30e1c3 ("net/hns3: support command interface with firmware")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The driver should not use the fixed value as the validity check of
RSS indirection table size with HW supported. As a result, it will
cause misjudgment when the RSS RETA size with HW supported have
changed.
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
When the hardware link status changes, the firmware proactively
reports the link status change message, and then driver update
link status. This feature is lack of a switch to control in PF
driver. Otherwise, this feature does not take effect when the
kernel PF driver that supports the feature is not loaded.
Fixes: 109e4dd1bd ("net/hns3: get link state change through mailbox")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
For Kunpeng930, the NIC engine support 1280 tqps being taken over by
a PF. In this case, a maximum of 1281 interrupt resources are also
supported in this PF. To support the maximum number of queues, several
patches are made. But the interrupt related modification are missing.
So, in RX interrupt mode, a large number of queues will be aggregated
into one interrupt due to insufficient interrupts. It will lead to
waste of interrupt resources and reduces usability.
To utilize all these interrupt resources, related IMP command has been
extended. And, the I/O address of the extended interrupt resources are
different from the existing ones. So, a function used for calculating
the address offset has been added.
Fixes: 76d794566d ("net/hns3: maximize queue number")
Fixes: 27911a6e62 ("net/hns3: add Rx interrupts compatibility")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Use errno array instead of switch-case for refactor
the hns3_cmd_convert_err_code function.
Besides, we add a type for ROH(RDMA Over HCCS) check
cmdq return error in Kunpeng930 NIC hardware.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The original command opcode '0x700A' may cause firmware error,
so '0x700A' is deserted, now use '0x700B' to replace it.
Fixes: 223d9eceae ("net/hns3: clear residual hardware configurations on init")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Some header files have included by others. Also,
some header files have a header file self-contained
error will trigger building warning. As a result,
it is unnecessary and move it into the correct
location.
Beside, here also remove some unused lines.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Forward error correction (FEC) is a bit error correction mode.
It adds error correction information to data packets at the
transmit end, and uses the error correction information to correct
the bit errors generated during data packet transmission at the
receive end. This improves signal quality but also brings a delay
to signals. This function can be enabled or disabled as required.
This patch adds FEC support for ethdev.Introduce ethdev
operations which support query and config FEC information in
hardware.
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Reviewed-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Reviewed-by: Chengwen Feng <fengchengwen@huawei.com>
Reviewed-by: Chengchang Tang <tangchengchang@huawei.com>
The new generation hns3 network engine supports independent enabling and
disabling of a single Tx/Rx queue. So, it can support the queue start
and stop feature. In addition, when different numbers of Tx and Rx
queues need to be enabled in some applications, hns3 pmd does not need
to create fake queues to enable these scenarios.
This patch Add queue start and stop feature for the new generation hns3
networking engine. Cancel the creation of fake queue on the new
generation network engine. And the previously improperly named queue
related function was renamed to improve readability.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The maximum number of queues for hns3 PF and VF driver is 64 based on
hns3 network engine with revision_id equals 0x21. Based on hns3 network
engine with revision_id equals 0x30, the hns3 PF PMD driver can support
up to 1280 queues, and hns3 VF PMD driver can support up to 128 queues.
The following points need to be modified to support maximizing queue
number and maintain better compatibility:
1) Maximizing the number of queues for hns3 PF and VF PMD driver In
current version, VF is not supported when PF is driven by hns3 PMD
driver. If maximum queue numbers allocated to PF PMD driver is less
than total tqps_num allocated to this port, all remaining number of
queues are mapped to VF function, which is unreasonable. So we fix
that all remaining number of queues are mapped to PF function.
Using RTE_LIBRTE_HNS3_MAX_TQP_NUM_PER_PF which comes from
configuration file to limit the queue number allocated to PF device
based on hns3 network engine with revision_id greater than 0x30. And
PF device still keep the maximum 64 queues based on hns3 network
engine with revision_id equals 0x21.
Remove restriction of the macro HNS3_MAX_TQP_NUM_PER_FUNC on the
maximum number of queues in hns3 VF PMD driver and use the value
allocated by hns3 PF kernel netdev driver.
2) According to the queue number allocated to PF device, a variable
array for Rx and Tx queue is dynamically allocated to record the
statistics of Rx and Tx queues during the .dev_init ops
implementation function.
3) Add an extended field in hns3_pf_res_cmd to support the case that
numbers of queue are greater than 1024.
4) Use new base address of Rx or Tx queue if QUEUE_ID of Rx or Tx queue
is greater than 1024.
5) Remove queue id mask and use all bits of actual queue_id as the
queue_id to configure hardware.
6) Currently, 0~9 bits of qset_id in hns3_nq_to_qs_link_cmd used to
record actual qset id and 10 bit as VLD bit are configured to
hardware. So we also need to use 11~15 bits when actual qset_id is
greater than 1024.
7) The number of queue sets based on different network engine are
different. We use it to calculate group number and configure to
hardware in the backpressure configuration.
8) Adding check operations for number of Rx and Tx queue user configured
when mapping queue to tc Rx queue numbers under a single TC must be
less than rss_size_max supported by a single TC. Rx and Tx queue
numbers are allocated to every TC by average. So Rx and Tx queue
numbers must be an integer multiple of 2, or redundant queues are not
available.
9) We can specify which packets enter the queue with a specific queue
number, when creating flow table rules by rte_flow API. Currently,
driver uses 0~9 bits to record the queue_id. So it is necessary to
extend one bit field to record queue_id and configure to hardware, if
the queue_id is greater than 1024.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The maximum number of queues for one TC hns3 PF PMD driver supported is
64 based on hns3 network engine with revision_id equals 0x21, while it
is expanded up to 512 on hns3 network engine with revision_id equals
0x30.
So the following points need to be modified to maintain better
compatibility.
1) Using a extended rss_size_max field as the maximum queue number of
one TC PF driver supported.
2) The data type of the RSS redirection table needs to be changed from
uint8_t to uint16_t.
3) rss_tc_mode modification
The bitwidth of tc_offset, meaning the rx queue index, has to expand
from 10 bit to 11 bits. The tc_size, meaning the exponent with base 2
of queues supported on TC, needs to expand from 3 bits to 4 bits.
4) RSS indirection table modification
Currently, a field with 7 bits width is used to record the queue
index for RSS indirection table. It means that PF needs to expand the
queue index field to 9 bits. As the RSS indirection table config
command reserved 4 bytes to configure the RSS queue index, a extern
field can be added. So an entries of RSS indirection table queue
index has two fields to set: rss_result_l and rss_result_h, while
rss_result_l records the lower 8 bits and rss_result_h records the
higher 1 bit.
In addition, 2~4 modifications is also compatible with hns3 VF PMD
driver.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch support for hash type input set configuration. That is, upper
level application can call the rte_flow_create or
rte_eth_dev_rss_hash_update API to set the specified tuples by RSS types.
As a result, the hardware can selectively use the tuples to perform hash
calculation based on the specific tuple to enable the fields.
The following uses the RSS flow as an example:
When application calls the rte_flow_create API to select tuple input for
ipv4-tcp l3-src-only, the driver can enable the ipv4-tcp src field of the
hardware register by calling the internal function named
hns3_set_rss_tuple_by_rss_hf according to the RSS types in actions list.
In testpmd application, the command as follows:
testpmd> flow create 0 ingress pattern end actions rss types \
ipv4-tcp l3-src-only end queues 1 3 end / end
The following use the rte_eth_dev_rss_hash_update as an example:
if the user set the select tuple input for ipv4-tcp l3-src-only by
rte_eth_rss_conf structure in rte_eth_dev_rss_hash_update. the next
flow is the same as that of the RSS flow. In testpmd application,
the command as follows:
testpmd> port config all rss ipv4-tcp l3-src-only
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Kunpeng 930 hardware support spread packets to region of queues which can
be configured by FDIR rule, it means user can create one FDIR rule which
action is one region of queues, and then RSS use the region info to spread
packets.
As we know, RTE_FLOW_ACTION_TYPE_RSS is used to spread packets among
several queues, user could config such as func/level/types/key/queue
parameter to control RSS function, so we provide this feature under the
RTE_FLOW_ACTION_TYPE_RSS framework.
Consider RSS input tuple don't have eth header, we use the following
rule to distinguish them (whether it's queue region configuration or
rss general configuration):
Case 1: pattern have ETH and action's queue_num > 0, indicate it is
queue region configuration.
Case other: rss general configuration.
So if user want to configure one flow which ipv4=192.168.1.192 spread to
queue region of queue 0/1/2/3, the patter should:
RTE_FLOW_ITEM_TYPE_ETH with spec=last=mask=NULL
RTE_FLOW_ITEM_TYPE_IPV4 with spec=192.168.1.192 last=mask=NULL
RTE_FLOW_ITEM_TYPE_END
the action should:
RTE_FLOW_ACTION_TYPE_RSS with queue_num=4 queue=0/1/2/3
RTE_FLOW_ACTION_TYPE_END
after calling rte_flow_create, one FDIR rule will be created.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Because of hardware limitation based on the old version of hns3 network
engine, there are some restrictions:
a) HNS3 PMD driver needs select different processing mode for VLAN based
on whether PVID is set which means our driver need sense the PVID
states.
b) For packets transmitting process, only two layer of VLAN tag is
supported. If the total number of VLAN tags in mbuf and VLAN offload
by hardware (VLAN insert by descriptor) exceeds two, the VLAN in mbuf
will be overwritten by VLAN in the descriptor.
c) If port based VLAN is set, only one VLAN header is allowed in mbuf or
it will be discard by hardware.
In order to solve these restriction, two change is implemented on the
new versions of network engine.
1) add a new VLAN tagged insertion mode, named tag shift mode;
2) add a new VLAN strip control bit, named strip hide enable;
The tag shift mode means that VLAN tag will shift automatically when the
inserted place has a tag. For PMD driver, the VLAN tag1 and tag2
configurations in Tx side do not need to be considered because the
hardware completes it. However, the related configuration will still be
retained to be compatible with the old version of network engine.
The VLAN strip hide means that hardware will strip the VLAN tag and hide
VLAN in descriptor (VLAN ID exposed as zero and related STRIP_TAGP is
off).
These changes make it no longer necessary for the hns3 PMD driver to be
aware of the PVID status and have the ability to send mult-layer (more
than two) VLANs packets. Therefore, hns3 PMD driver introduces the
concept of VLAN mode and adds a new VLAN mode named HNS3_PVID_MODE to
indicate that PVID-related IO process can be implemented by the
hardware. And VF driver does not need to be modified because the related
mailbox messages will not be sent by PF kernel mode netdev driver under
new network engine and all the related hardware configuration is on the
PF side.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The new firmware adds the hardware error types reported by MSI-x mode.
These errors are defined as RAS errors in hardware and belong to a
different type from the MSI-x errors processed by the driver.
When hardware detects an error which must be handled by the driver for
device to run properly it reports the error information through the
MSI-x interrupt. After receiving the interrupt reported by the hardware,
the driver queries the error information and identifies the error level,
then rectifies the error. All errors will be logged.
In addition, the hardware may be reset at the function or global level
based on the error level. After the reset is complete, the hardware will
recover to the normal status.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
There are difference about queue's interrupt configurations for
different versions of hardware network engine, such as queue's interrupt
mapping mode, coalesce configuration, etc.
The following uses the configuration differences of the interrupt
mapping mode as an example.
1) For some versions of hardware network engine, such as kunpeng 920,
because of the hardware constraint, we need implement unmmapping
relationship configurations by binding all queues to the last
interrupt vector and reserving the last interrupt vector. This
results in a decrease of the maximum queues when upper applications
call the rte_eth_dev_configure API function to enable Rx interrupt.
2) And for another versions, such as kunpeng 930, hns3 PMD driver can
map/unmmap all interrupt vectors with queues when Rx interrupt is
enabled.
This patch resolves configuration differences about Rx interrupts based
on kunpeng 920 and kunpeng 930.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds getting device capabilities from firmware, so driver can
supply different capabilities and specifications to upper level
applications base on different versions of hardware network engine.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The 200G device has a new device id 0xA228, so adds this device id
to pci table for pci driver can probe it. Similar to the network port
with other speed, the hns3 PMD driver gets 200G speed information
from firmware, and passes them to DPDK framework.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
When the last driver exits abnormally, for example, it is killed by
'kill -9', it may be too late to clear the configuration and cause the
configuration to remain. Therefore, to ensure that the hardware
environment is clean during initialization, the PF driver actively clear
the hardware environment during initialization, including PF and
corresponding VFs' vlan, mac, flow table configurations, etc.
Fixes: d51867db65 ("net/hns3: add initialization")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
This patch modifies the print format for firmware version in the log, It
replaces "0x%08x" with "%lu.%lu.%lu.%lu" in the format control string.
By the way, this patch adds ".fw_version_get" ops implemation for hns3
VF PMD driver.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, when receiving and transmitting packets based on hns3 network
engine there are probably unexpected and redundant Tx interrupts if Rx
interrupt is enabled.
The root cause as below:
Tx and Rx queues with the same number share the interrupt vector in hns3
network engine, and in this case there are the residual hardware mapping
relationship configuration between queue and interrupt vector configured
in hns3 kernel ethdev driver.
We should clear the all hardware mapping relationship configurations in
the initialization. Because of the hardware constraints, we have to
implement clearing the relationship by binding all queues to the last
interrupt vector and reserving the last interrupt vector, this method
results in a decrease of the maximum queues when upper applications call
the rte_eth_dev_configure API function to enable Rx interrupt.
Fixes: 02a7b55657 ("net/hns3: support Rx interrupt")
Cc: stable@dpdk.org
Signed-off-by: Hao Chen <chenhao164@huawei.com>
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds supports of receive packets through interrupt mode for
hns3 PF/VF driver. The following ops functions should be implemented
defined in the struct eth_dev_ops:
rx_queue_intr_enable
rx_queue_intr_disable
Signed-off-by: Hao Chen <chenhao164@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds support for cmd of hns3 PMD driver, driver can interact
with firmware through command to complete hardware configuration.
Signed-off-by: Hao Chen <chenhao164@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chunsong Feng <fengchunsong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
