There is a confusion on setting max Rx packet length, this patch aims to
clarify it.
'rte_eth_dev_configure()' API accepts max Rx packet size via
'uint32_t max_rx_pkt_len' field of the config struct 'struct
rte_eth_conf'.
Also 'rte_eth_dev_set_mtu()' API can be used to set the MTU, and result
stored into '(struct rte_eth_dev)->data->mtu'.
These two APIs are related but they work in a disconnected way, they
store the set values in different variables which makes hard to figure
out which one to use, also having two different method for a related
functionality is confusing for the users.
Other issues causing confusion is:
* maximum transmission unit (MTU) is payload of the Ethernet frame. And
'max_rx_pkt_len' is the size of the Ethernet frame. Difference is
Ethernet frame overhead, and this overhead may be different from
device to device based on what device supports, like VLAN and QinQ.
* 'max_rx_pkt_len' is only valid when application requested jumbo frame,
which adds additional confusion and some APIs and PMDs already
discards this documented behavior.
* For the jumbo frame enabled case, 'max_rx_pkt_len' is an mandatory
field, this adds configuration complexity for application.
As solution, both APIs gets MTU as parameter, and both saves the result
in same variable '(struct rte_eth_dev)->data->mtu'. For this
'max_rx_pkt_len' updated as 'mtu', and it is always valid independent
from jumbo frame.
For 'rte_eth_dev_configure()', 'dev->data->dev_conf.rxmode.mtu' is user
request and it should be used only within configure function and result
should be stored to '(struct rte_eth_dev)->data->mtu'. After that point
both application and PMD uses MTU from this variable.
When application doesn't provide an MTU during 'rte_eth_dev_configure()'
default 'RTE_ETHER_MTU' value is used.
Additional clarification done on scattered Rx configuration, in
relation to MTU and Rx buffer size.
MTU is used to configure the device for physical Rx/Tx size limitation,
Rx buffer is where to store Rx packets, many PMDs use mbuf data buffer
size as Rx buffer size.
PMDs compare MTU against Rx buffer size to decide enabling scattered Rx
or not. If scattered Rx is not supported by device, MTU bigger than Rx
buffer size should fail.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Huisong Li <lihuisong@huawei.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Added macros to simplify print of MAC address.
The six bytes of a MAC address are extracted in
a macro here, to improve code readablity.
Signed-off-by: Aman Deep Singh <aman.deep.singh@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Added macro to print six bytes of MAC address.
The MAC addresses will be printed in upper case
hexadecimal format.
In case there is a specific check for lower case
MAC address, the user may need to make a change in
such test case after this patch.
Signed-off-by: Aman Deep Singh <aman.deep.singh@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Currently the sample app user guides use hard coded code snippets,
this patch changes these to use literalinclude which will dynamically
update the snippets as changes are made to the code.
This was introduced in commit 413c75c33c40 ("doc: show how to include
code in guides"). Comments within the sample apps were updated to
accommodate this as part of this patch. This will help to ensure that
the code within the sample app user guides is up to date and not out
of sync with the actual code.
Signed-off-by: Conor Fogarty <conor.fogarty@intel.com>
Signed-off-by: Conor Walsh <conor.walsh@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Add same tag as other files in this example.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Add event dev main loop based on enabled l2fwd options and eventdev
capabilities.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Acked-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
