In function cmd_set_mplsogre_encap_parsed(), MPLS label value was
set in mplsogre_encap_conf struct without the required offset.
As a result the value was copied incorrectly into
rte_flow_item_mpls struct.
This patch sets MPLS label value in appropriate location at
mplsogre_encap_conf struct, so it is correctly copied to
rte_flow_item_mpls struct.
Fixes: 3e77031be855 ("app/testpmd: add MPLSoGRE encapsulation")
Cc: stable@dpdk.org
Signed-off-by: Dekel Peled <dekelp@mellanox.com>
Acked-by: Ori Kam <orika@mellanox.com>
In function cmd_set_mplsoudp_encap_parsed(), MPLS label value was
set in mplsoudp_encap_conf struct without the required offset.
As a result the value was copied incorrectly into
rte_flow_item_mpls struct.
This patch sets MPLS label value in appropriate location at
mplsoudp_encap_conf struct, so it is correctly copied to
rte_flow_item_mpls struct.
Fixes: a1191d39cb57 ("app/testpmd: add MPLSoUDP encapsulation")
Cc: stable@dpdk.org
Signed-off-by: Dekel Peled <dekelp@mellanox.com>
Acked-by: Ori Kam <orika@mellanox.com>
There is an error in function search_rx_offload(),
it will break when get unexpected return value from function
rte_eth_dev_rx_offload_name(), but rte_eth_dev_rx_offload_name()
will return some unexpected value indeed.
Fixes: c73a9071877a ("app/testpmd: add commands to test new offload API")
Cc: stable@dpdk.org
Signed-off-by: Wei Zhao <wei.zhao1@intel.com>
Tested-by: Yuan Peng <yuan.peng@intel.com>
Set port status to stopped for newly added devices.
Fixes: 2950a769315e ("bond: testpmd support")
Cc: stable@dpdk.org
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
As struct rte_tm_shaper_params defined, the command line of
testpmd should include committed and peak parameters, but
right now the command line doesn't identify whether it's
committed or peak parameter. This patch identifies and
adds the clarify definition
Fixes: bddc2f40b594 ("app/testpmd: add commands for shaper and wred profiles")
Cc: stable@dpdk.org
Signed-off-by: Rosen Xu <rosen.xu@intel.com>
After probing is done, each new port must be setup.
The new ports are currently guessed by iterating on ports
matching the devargs string used for probing.
When probing a port, it is possible that one more port probing
get triggered (e.g. PF is automatically probed when probing
a VF representor). Such automatic probing will be caught only on event.
The iterator loop may be replaced by a call from the event callback.
In order to be able to test both modes, a command is added
to choose between iterator and event modes.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
The command "port detach" is removing the EAL rte_device
of the ethdev port specified as parameter.
The function name and some comments are updated to make clear
that we are detaching the whole device.
After detaching, the pointer, which maps a port to its device,
is reset. This way, it is possible to check whether a port
is still associated to a (not removed) device.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Previous patch introduces the Tx metadata feature, with unnecessary
restrictions on data entry.
It also used the metadata in txonly fwd engine only.
This fix removes the data entry restrictions on metadata item.
It also implements callback function to add the metadata in every
Tx packet, sent by any fwd engine.
Fixes: c18feafa193c ("app/testpmd: support metadata as flow rule item")
Signed-off-by: Dekel Peled <dekelp@mellanox.com>
Acked-by: Ori Kam <orika@mellanox.com>
Example for MPLSoGRE tunnel:
ETH / IPV4 / GRE / MPLS / IP / L4..L7
In order to encapsulate such a tunnel there is a need to remove L2 of
the inner packet and encap the remaining tunnel, this is done by
applying 2 rte flow commands l2_decap followed by mplsogre_encap.
Both commands must appear in the same flow, and from the point of the
packet it both actions are applied at the same time. (There is no part
where a packet doesn't have L2 header).
Decapsulating such a tunnel works the other way, first we need to decap
the outer tunnel header and then apply the new L2.
So the commands will be mplsogre_decap / l2_encap
Due to the complex encapsulation of MPLSoGRE flow action and
based on the fact testpmd does not allocate memory, this patch adds a
new command in testpmd to initialise a global structure containing the
necessary information to make the outer layer of the packet. This same
global structures will then be used by the flow commands in testpmd when
the action mplsogre_encap, mplsogre_decap, will be parsed, at this
point, the conversion into such action becomes trivial.
Signed-off-by: Ori Kam <orika@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
MPLSoUDP is an example for L3 tunnel encapsulation.
L3 tunnel type is a tunnel that is missing the layer 2 header of the
inner packet.
Example for MPLSoUDP tunnel:
ETH / IPV4 / UDP / MPLS / IP / L4..L7
In order to encapsulate such a tunnel there is a need to remove L2 of
the inner packet and encap the remaining tunnel, this is done by
applying 2 rte flow commands l2_decap followed by mplsoudp_encap.
Both commands must appear in the same flow, and from the point of the
packet it both actions are applied at the same time. (There is no part
where a packet doesn't have L2 header).
Decapsulating such a tunnel works the other way, first we need to decap
the outer tunnel header and then apply the new L2.
So the commands will be mplsoudp_decap / l2_encap
Due to the complex encapsulation of MPLSoUDP and L2 flow actions and
based on the fact testpmd does not allocate memory, this patch adds a
new command in testpmd to initialise a global structures containing the
necessary information to make the outer layer of the packet. This same
global structures will then be used by the flow commands in testpmd when
the action mplsoudp_encap, mplsoudp_decap, l2_encap, l2_decap, will be
parsed, at this point, the conversion into such action becomes trivial.
The l2_encap and l2_decap actions can also be used for other L3 tunnel
types.
Signed-off-by: Ori Kam <orika@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
As described in [1], this series adds option to set metadata value
as match pattern when creating a new flow rule.
This patch introduces additional options in testpmd commands:
- New item type "meta" "data"
- New per-port offload flag "match_metadata".
It also adds commands to configure the tx_metadata value to use:
- New 'config' command takes a 32 bit value and stores it per port:
port config <port_id> tx_metadata <value>
testpmd will add to any Tx packet sent from this port the metadata
value, and set ol_flags accordingly.
- A matching 'show' command is added to read the configured value:
port config <port_id> tx_metadata <value>
[1] "ethdev: support metadata as flow rule criteria"
Signed-off-by: Dekel Peled <dekelp@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add following testpmd run-time commands to support test of TM packet
marking:
set port tm mark ip_ecn <port_id> <green> <yellow> <red>
set port tm mark ip_dscp <port_id> <green> <yellow> <red>
set port tm mark vlan_dei <port_id> <green> <yellow> <red>
Signed-off-by: Krzysztof Kanas <krzysztof.kanas@caviumnetworks.com>
In interactive mode, when the "quit" command is issued, pmd_test_exit()
is being called twice, once through the "quit" command and the other
after termination of prompt.
Remove duplicated exit routine by removing call from "quit" command.
Steps to reproduce:
- Run testpmd in interactive mode.
- type "quit".
Fixes: af75078fece3 ("first public release")
Cc: stable@dpdk.org
Signed-off-by: Brian Archbold <brian.archbold@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
existing testpmd command "show port info" is too verbose.
Added a new summary command to print brief information on ports.
console output:
testpmd> show port summary all
Number of available ports: 2
Port MAC Address Name Driver Status Link
0 11:22:33:44:55:66 0000:07:00.0 net_i40e up 40000Mbps
1 66:55:44:33:22:11 0000:07:00.1 net_i40e up 40000Mbps
Signed-off-by: Emma Finn <emma.finn@intel.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Added outer-udp Tx HW checksum support for csum forward engine
if device supports DEV_TX_OFFLOAD_OUTER_UDP_CKSUM.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Command shouldn't ask RSS hash functions as argument to get supported
RSS hash function, those values will be overwritten by PMD anyway.
To display configured RSS hash functions
"show port (port_id) rss-hash"
To display configured RSS hash functions and hash key
"show port (port_id) rss-hash key"
Fixes: 8205e241b2b0 ("app/testpmd: add missing type to RSS hash commands")
Cc: stable@dpdk.org
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Based on the documentation and help print, the sub command
for csum suppose to be "parse-tunnel" instead of "parse_tunnel".
Fixes: 64fc36064dc3 ("app/testpmd: add csum parse-tunnel command")
Cc: stable@dpdk.org
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Removed DEV_RX_OFFLOAD_CRC_STRIP offload flag.
Without any specific Rx offload flag, default behavior by PMDs is to
strip CRC.
PMDs that support keeping CRC should advertise DEV_RX_OFFLOAD_KEEP_CRC
Rx offload capability.
Applications that require keeping CRC should check PMD capability first
and if it is supported can enable this feature by setting
DEV_RX_OFFLOAD_KEEP_CRC in Rx offload flag in rte_eth_dev_configure()
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Tomasz Duszynski <tdu@semihalf.com>
Acked-by: Shahaf Shuler <shahafs@mellanox.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Jan Remes <remes@netcope.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Without this patch, testpmd command to config Rx offload keep_crc
would fail and report "Bad argument".
This patch also fix the command to config the Tx offload mbuf_fast_free.
Fixes: 70815c9ecadd ("ethdev: add new offload flag to keep CRC")
Fixes: c73a9071877a ("app/testpmd: add commands to test new offload API")
Cc: stable@dpdk.org
Signed-off-by: Wei Dai <wei.dai@intel.com>
Tested-by: Yuan Peng <yuan.peng@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
If the "port config all crc-strip on" command is issued,
The DEV_RX_OFFLOAD_KEEP_CRC offload flag should be cleared.
If the "port config all crc-strip off command is issued,
The DEV_RX_OFFLOAD_KEEP_CRC offload flag should be set.
Fixes: 70815c9ecadd ("ethdev: add new offload flag to keep CRC")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
This patch reverts the testpmd CLI prompt routine modifications done
in order to support softnic.
The reason of doing so is due to testpmd abnormal exit observed on
several setups caused by the softnic modifications to this routine,
for example: When running testpmd with tap interface
(testpmd
-n 4 --vdev=net_tap0,iface=tap0,remote=eth1 -- --burst=64
--mbcache=512 -i --nb-cores=7 --rxq=2 --txq=2 --txd=512
--rxd=512 --port-topology=chained --forward-mode=rxonly)
testpmd crashes seconds after presenting its prompt with the following
error:
testpmd> PANIC in prompt():
CLI poll error (-1)
Thread 1 "testpmd" received signal SIGABRT, Aborted.
0x00007ffff668e0d0 in raise () from /lib64/libc.so.6
(gdb) bt
#0 0x00007ffff668e0d0 in raise () from /lib64/libc.so.6
#1 0x00007ffff668f6b1 in abort () from /lib64/libc.so.6
#2 0x0000000000468027 in __rte_panic ()
#3 0x00000000004876ed in prompt ()
#4 0x000000000046dffc in main ()
When running testpmd with bare-metal device
(testpmd -n 4 --socket-mem=1024,1024 -w 04:00.0 --
--burst=64 --mbcache=512 -i --nb-cores=7
--rxq=64 --txq=4 --txd=16 --rxd=16)
and pressing CTRL+D right after testpmd prompt is presented then
the program crashes while presenting the same messages as above.
Needless to say that this behavior is not observed when using the
previous CLI prompt routine.
Fixes: 0ad778b398c6 ("app/testpmd: rework softnic forward mode")
Signed-off-by: Moti Haimovsky <motih@mellanox.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Due to the complex NVGRE_ENCAP flow action and based on the fact testpmd
does not allocate memory, this patch adds a new command in testpmd to
initialise a global structure containing the necessary information to
make the outer layer of the packet. This same global structure will
then be used by the flow command line in testpmd when the action
nvgre_encap will be parsed, at this point, the conversion into such
action becomes trivial.
This global structure is only used for the encap action.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Ori Kam <orika@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Mohammad Abdul Awal <mohammad.abdul.awal@intel.com>
Tested-by: Mohammad Abdul Awal <mohammad.abdul.awal@intel.com>
Due to the complex VXLAN_ENCAP flow action and based on the fact testpmd
does not allocate memory, this patch adds a new command in testpmd to
initialise a global structure containing the necessary information to
make the outer layer of the packet. This same global structure will
then be used by the flow command line in testpmd when the action
vxlan_encap will be parsed, at this point, the conversion into such
action becomes trivial.
This global structure is only used for the encap action.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Ori Kam <orika@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Mohammad Abdul Awal <mohammad.abdul.awal@intel.com>
Tested-by: Mohammad Abdul Awal <mohammad.abdul.awal@intel.com>
udp_cksum is duplicated, second one should be tcp_cksum
Fixes: c73a9071877a ("app/testpmd: add commands to test new offload API")
Cc: stable@dpdk.org
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Modied the testpmd softnic forwarding mode as per the
changes in softnic PMD.
To run testpmd application with softnic fwd mode, following
command is used;
$ ./testpmd -c 0xc -n 4 --vdev 'net_softnic0,firmware=script.cli'
-- -i --forward-mode=softnic
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
This patch enables GSO for UDP/IPv4 packets. Oversized UDP/IPv4
packets transmitted over a GSO-enabled port will undergo segmentation.
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Acked-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Tested-by: Yuwei Zhang <yuwei1.zhang@intel.com>
ethdev layer introduced checks for application requested RSS hash
functions and returns error for ones unsupported by hardware
This check breaks some sample applications which blindly configures
RSS hash functions without checking underlying hardware support.
Updated examples to mask out unsupported RSS has functions during device
configuration.
Prints a log if configuration values updated by this check.
Fixes: aa1a6d87f15d ("ethdev: force RSS offload rules again")
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Meijuan Zhao <meijuanx.zhao@intel.com>
Tested-by: Yingya Han <yingyax.han@intel.com>
Acked-by: David Hunt <david.hunt@intel.com>
Add following testpmd run-time commands to support test of
new Rx offload API:
show port <port_id> rx_offload capabilities
show port <port_id> rx_offload configuration
port config <port_id> rx_offload <offload> on|off
port <port_id> rxq <queue_id> rx_offload <offload> on|off
Above last 2 commands should be run when the port is stopped.
And <offload> can be one of "vlan_strip", "ipv4_cksum", ...
Add following testpmd run-time commands to support test of
new Tx offload API:
show port <port_id> tx_offload capabilities
show port <port_id> tx_offload configuration
port config <port_id> tx_offload <offload> on|off
port <port_id> txq <queue_id> tx_offload <offload> on|off
Above last 2 commands should be run when the port is stopped.
And <offload> can be one of "vlan_insert", "udp_cksum", ...
Signed-off-by: Wei Dai <wei.dai@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Traffic manager provides an API for resuming
an arbitrary node in a hierarchy.
This commit adds support for calling this API
from testpmd.
Signed-off-by: Tomasz Duszynski <tdu@semihalf.com>
Reviewed-by: Jasvinder Singh <jasvinder.singh@intel.com>
Traffic manager provides an API for suspending
an arbitrary node in a hierarchy.
This commit adds support for calling this API from testpmd.
Signed-off-by: Tomasz Duszynski <tdu@semihalf.com>
Reviewed-by: Jasvinder Singh <jasvinder.singh@intel.com>
After add RSS hash offload check, default rss_hf will fail on
devices that not support all bits, the patch take rss_hf as
a suggest value and only set bits that device supported base on
rte_eth_dev_get_info, also rss_hf will only be updated when new
rss offload is successfully updated on all ports by
"port config all rss [!default]" command.
Fixes: 8863a1fbfc66 ("ethdev: add supported hash function check")
Fixes: d9aa619c60b6 ("app/testpmd: new parameter for port config all RSS command")
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
This change adds a new option to "port config" command to
add udp tunnel port for VXLAN and GENEVE tunneling protocols.
This command can be extended for other tunneling protocols
listed in "enum rte_eth_tunnel_type" as and when needed.
usage:
port config <port_id> udp_tunnel_port add|rm vxlan|geneve <udp_port>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add command to change specific queue's ring size configure,
the new value will only take effect after command that restart
the device(port stop <port_id>/port start <port_id>) or command
that setup the queue(port <port_id> rxq <qid> setup) at runtime.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Each queue has independent configure information in rte_port.
Base on this, we are able to add new commands to configure
different queues with different value.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add new command to setup queue, rte_eth_[rx|tx]_queue_setup will
be called corresponsively.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Correct couple port id from uint8_t to uint16_t.
Fixes: f8244c6399d9 ("ethdev: increase port id range")
Cc: stable@dpdk.org
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patches add "default" parameter to "port config all rss" command.
"default" means all supported hash types reported by device info.
Signed-off-by: Xueming Li <xuemingl@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Except for a list of queues, RSS configuration (hash key and fields) cannot
be specified from the flow command line and testpmd does not provide safe
defaults either.
In order to validate their implementation with testpmd, PMDs had to
interpret its NULL RSS configuration parameters somehow, however this has
never been valid to begin with.
This patch makes testpmd always provide default values.
The list of RSS types to use is exclusively taken from the global "rss_hf"
variable, itself configured through the "port config all rss" command or
--rss-ip/--rss-udp command-line options.
Fixes: 05d34c6e9d2c ("app/testpmd: add queue actions to flow command")
Cc: stable@dpdk.org
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
The previous symbols were deprecated for two releases.
They are now marked as such and cannot be used anymore.
They are replaced by ones respecting the new namespace that are marked
experimental.
As a result, eth_dev attach and detach are slightly reworked to follow
the changes.
Signed-off-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Unused variables will appear when setting RTE_LIBRTE_I40E_PMD
to be disabled.
The fix was to move these variables to the I40E_PMD scope,
since only I40E_PMD is using it.
Fixes: a9dbe1802226 ("fix ethdev port id validation")
Signed-off-by: Wisam Jaddo <wisamm@mellanox.com>
Some DPDK applications wrongly assume these requirements:
- no hotplug, i.e. ports are never detached
- all allocated ports are available to the application
Such application iterates over ports by its own mean.
The most common pattern is to request the port count and
assume ports with index in the range [0..count[ can be used.
In order to fix this common mistake in all external applications,
the function rte_eth_dev_count is deprecated, while introducing
the new functions rte_eth_dev_count_avail and rte_eth_dev_count_total.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Some DPDK applications wrongly assume these requirements:
- no hotplug, i.e. ports are never detached
- all allocated ports are available to the application
Such application assume a valid port index is in the range [0..count[.
There are three consequences when using such wrong design:
- new ports having an index higher than the port count won't be valid
- old ports being detached (RTE_ETH_DEV_UNUSED) can be valid
Such mistake will be less common with growing hotplug awareness.
All applications and examples inside this repository - except testpmd -
must be fixed to use the function rte_eth_dev_is_valid_port.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Some DPDK applications wrongly assume these requirements:
- no hotplug, i.e. ports are never detached
- all allocated ports are available to the application
Such application iterates over ports by its own mean.
The most common pattern is to request the port count and
assume ports with index in the range [0..count[ can be used.
There are three consequences when using such wrong design:
- new ports having an index higher than the port count won't be seen
- old ports being detached (RTE_ETH_DEV_UNUSED) can be seen as ghosts
- failsafe sub-devices (RTE_ETH_DEV_DEFERRED) will be seen by the application
Such mistake will be less common with growing hotplug awareness.
All applications and examples inside this repository - except testpmd -
must be fixed to use the iterator RTE_ETH_FOREACH_DEV.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
The optimal values of several transmission & reception related
parameters, such as burst sizes, descriptor ring sizes, and number
of queues, varies between different network interface devices. This
patch allows testpmd to make use of per-PMD tuned parameter values.
Signed-off-by: Remy Horton <remy.horton@intel.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
The dynamic link is broken for ARM platform because the dependencies
of the DPAA PMD are not declared.
Fixes: 83c82e15e1c0 ("app/testpmd: support loopback config for DPAA")
Cc: stable@dpdk.org
Reported-by: Marco Varlese <mvarlese@suse.de>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
