Fix the mbuf offload flags namespace by adding an RTE_ prefix to the
name. The old flags remain usable, but a deprecation warning is issued
at compilation.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Add 'RTE_ETH' namespace to all enums & macros in a backward compatible
way. The macros for backward compatibility can be removed in next LTS.
Also updated some struct names to have 'rte_eth' prefix.
All internal components switched to using new names.
Syntax fixed on lines that this patch touches.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Tyler Retzlaff <roretzla@linux.microsoft.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Wisam Jaddo <wisamm@nvidia.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Chenbo Xia <chenbo.xia@intel.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
There is a confusion on setting max Rx packet length, this patch aims to
clarify it.
'rte_eth_dev_configure()' API accepts max Rx packet size via
'uint32_t max_rx_pkt_len' field of the config struct 'struct
rte_eth_conf'.
Also 'rte_eth_dev_set_mtu()' API can be used to set the MTU, and result
stored into '(struct rte_eth_dev)->data->mtu'.
These two APIs are related but they work in a disconnected way, they
store the set values in different variables which makes hard to figure
out which one to use, also having two different method for a related
functionality is confusing for the users.
Other issues causing confusion is:
* maximum transmission unit (MTU) is payload of the Ethernet frame. And
'max_rx_pkt_len' is the size of the Ethernet frame. Difference is
Ethernet frame overhead, and this overhead may be different from
device to device based on what device supports, like VLAN and QinQ.
* 'max_rx_pkt_len' is only valid when application requested jumbo frame,
which adds additional confusion and some APIs and PMDs already
discards this documented behavior.
* For the jumbo frame enabled case, 'max_rx_pkt_len' is an mandatory
field, this adds configuration complexity for application.
As solution, both APIs gets MTU as parameter, and both saves the result
in same variable '(struct rte_eth_dev)->data->mtu'. For this
'max_rx_pkt_len' updated as 'mtu', and it is always valid independent
from jumbo frame.
For 'rte_eth_dev_configure()', 'dev->data->dev_conf.rxmode.mtu' is user
request and it should be used only within configure function and result
should be stored to '(struct rte_eth_dev)->data->mtu'. After that point
both application and PMD uses MTU from this variable.
When application doesn't provide an MTU during 'rte_eth_dev_configure()'
default 'RTE_ETHER_MTU' value is used.
Additional clarification done on scattered Rx configuration, in
relation to MTU and Rx buffer size.
MTU is used to configure the device for physical Rx/Tx size limitation,
Rx buffer is where to store Rx packets, many PMDs use mbuf data buffer
size as Rx buffer size.
PMDs compare MTU against Rx buffer size to decide enabling scattered Rx
or not. If scattered Rx is not supported by device, MTU bigger than Rx
buffer size should fail.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Huisong Li <lihuisong@huawei.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Currently, most ethdev callback API use queue ID as parameter, but Rx
and Tx queue release callback use queue object which is used by Rx and
Tx burst data plane callback.
To align with other eth device queue configuration callbacks:
- queue release callbacks are changed to use queue ID
- all drivers are adapted
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Reviewed-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
The function rte_malloc() could return NULL, the return value
need to be checked.
Fixes: ce7ea764597e ("net/mvneta: support Rx/Tx")
Cc: stable@dpdk.org
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Acked-by: Liron Himi <lironh@marvell.com>
For tx checksum offload it is not mandatory to provide
a valid packet_type in addition to a valid ol_flags.
This patch only use ol_flags information for this feature
as a performance improvement.
Signed-off-by: Liron Himi <lironh@marvell.com>
Reviewed-by: Yuri Chipchev <yuric@marvell.com>
Tested-by: Liron Himi <lironh@marvell.com>
Add part of PMD for actual reception/transmission.
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Zyta Szpak <zr@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
