Some files were left with full license and wrong copyright format.
They are switched to this format:
SPDX-License-Identifier: BSD-3-Clause
Copyright 2017 Mellanox Technologies, Ltd
Fixes: 5feecc57d9 ("align SPDX Mellanox copyrights")
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Shahaf Shuler <shahafs@mellanox.com>
When the fail-safe device is reconfigured, it attempts to register
again for the sub-devices LSC and RMV events.
Prevent an event registration if it is already done.
Fixes: 598fb8aec6 ("net/failsafe: support device removal")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
The fail-safe PMD registers to RMV event for each removable sub-device
port in order to cleanup the sub-device resources and switch the Tx
sub-device directly when it is plugged-out.
During removal time, the fail-safe PMD stops and closes the sub-device
but it doesn't unregister the LSC and RMV callbacks of the sub-device
port.
It can lead the callbacks to be called for a port which is no more
associated with the fail-safe sub-device, because there is not a
guarantee that a sub-device gets the same port ID for each plug-in
process. This port, for example, may belong to another sub-device of a
different fail-safe device.
Unregister the LSC and RMV callbacks for sub-devices which are not
used.
Fixes: 598fb8aec6 ("net/failsafe: support device removal")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
There is time between the sub-device port probing by the sub-device PMD
to the sub-device port ownership taking by a fail-safe port.
In this time, the port is available for the application usage. For
example, the port will be exposed to the applications which use
RTE_ETH_FOREACH_DEV iterator.
Thus, ownership unaware applications may manage the port in this time
what may cause a lot of problematic behaviors in the fail-safe
sub-device initialization.
Register to the ethdev NEW event to take the sub-device port ownership
before it becomes exposed to the application.
Fixes: a46f8d584e ("net/failsafe: add fail-safe PMD")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
A new hook function is added and called inside the PMDs at the end
of the device probing:
- in primary process, after allocating, init and config
- in secondary process, after attaching and local init
This new function is almost empty for now.
It will be used later to add some post-initialization processing.
For the PMDs calling the helpers rte_eth_dev_create() or
rte_eth_dev_pci_generic_probe(), the hook rte_eth_dev_probing_finish()
is called from here, and not in the PMD itself.
Note that the helper rte_eth_dev_create() could be used more,
especially for vdevs, avoiding some code duplication in PMDs.
Cc: stable@dpdk.org
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
The iterator function rte_eth_find_next_owned_by(), used by the
iterator macro RTE_ETH_FOREACH_DEV_OWNED_BY, are ignoring the devices
which are neither ATTACHED nor REMOVED. Thus sub-devices, having
the state DEFERRED, cannot be seen with the ethdev iterator.
The state RTE_ETH_DEV_DEFERRED can be replaced by
RTE_ETH_DEV_ATTACHED + owner.
Fixes: dcd0c9c32b ("net/failsafe: use ownership mechanism for slaves")
Cc: stable@dpdk.org
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
This patch check if a input requested offloading is valid or not.
Any reuqested offloading must be supported in the device capabilities.
Any offloading is disabled by default if it is not set in the parameter
dev_conf->[rt]xmode.offloads to rte_eth_dev_configure() and
[rt]x_conf->offloads to rte_eth_[rt]x_queue_setup().
If any offloading is enabled in rte_eth_dev_configure() by application,
it is enabled on all queues no matter whether it is per-queue or
per-port type and no matter whether it is set or cleared in
[rt]x_conf->offloads to rte_eth_[rt]x_queue_setup().
If a per-queue offloading hasn't be enabled in rte_eth_dev_configure(),
it can be enabled or disabled for individual queue in
ret_eth_[rt]x_queue_setup().
A new added offloading is the one which hasn't been enabled in
rte_eth_dev_configure() and is reuqested to be enabled in
rte_eth_[rt]x_queue_setup(), it must be per-queue type,
otherwise trigger an error log.
The underlying PMD must be aware that the requested offloadings
to PMD specific queue_setup() function only carries those
new added offloadings of per-queue type.
This patch can make above such checking in a common way in rte_ethdev
layer to avoid same checking in underlying PMD.
This patch assumes that all PMDs in 18.05-rc2 have already
converted to offload API defined in 17.11 . It also assumes
that all PMDs can return correct offloading capabilities
in rte_eth_dev_infos_get().
In the beginning of [rt]x_queue_setup() of underlying PMD,
add offloads = [rt]xconf->offloads |
dev->data->dev_conf.[rt]xmode.offloads; to keep same as offload API
defined in 17.11 to avoid upper application broken due to offload
API change.
PMD can use the info that input [rt]xconf->offloads only carry
the new added per-queue offloads to do some optimization or some
code change on base of this patch.
Signed-off-by: Wei Dai <wei.dai@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
The hot-plug alarm mechanism is responsible to practically execute both
plug in and out operations. It periodically tries to detect missed
sub-devices to be reconfigured and clean the resources of the removed
sub-devices.
The hot-plug alarm is started by the failsafe probe function, and it's
wrongly not stopped if failsafe instance got an error. for example
when starting failsafe with a MAC option, and giving it an invalid MAC
address this will lead to a NULL pointer for the dev private field. Then
when the hotplug alarm is called it will try to access this pointer,
which will lead to a segmentation fault.
Uninstall the hot-plug alarm in case of error in probe function.
Fixes: ebea83f8 ("net/failsafe: add plug-in support")
Cc: stable@dpdk.org
Signed-off-by: Raslan Darawsheh <rasland@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Advertise failsafe supported RSS functions as part of dev_infos_get
callback. Set failsafe default RSS hash functions to be:
ETH_RSS_IP, ETH_RSS_UDP, and ETH_RSS_TCP.
The result of failsafe RSS hash functions is the logical AND of the
RSS hash functions among all failsafe sub_devices and failsafe own
defaults.
Previous to this commit RSS support was reported as none. Since the
introduction of [1] it is required that all RSS configurations be
verified.
[1] commit 8863a1fbfc ("ethdev: add supported hash function check")
Signed-off-by: Ophir Munk <ophirmu@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Add rte_flow_action_count action data structure to enable shared
counters across multiple flows on a single port or across multiple
flows on multiple ports within the same switch domain. Also this enables
multiple count actions to be specified in a single flow action.
This patch also modifies the existing rte_flow_query API to take the
rte_flow_action structure as an input parameter instead of the
rte_flow_action_type enumeration to allow querying a specific action
from a flow rule when multiple actions of the same type are specified.
This patch also contains updates for the bonding, failsafe and mlx5 PMDs
and testpmd application which are affected by this API change.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Add DEV_TX_OFFLOAD_TCP_TSO to failsafe Tx offload default capabilities.
The net result of failsafe Tx capabilities is the logical AND of Tx
capabilities among all failsafe sub_devices and failsafe own default
capabilities.
Signed-off-by: Ophir Munk <ophirmu@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
rte_eal_devargs is useless, rte_devargs is sufficient.
Only experimental functions are changed for now.
Signed-off-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
rte_eal_devargs_parse can be used by EAL subsystems, drivers,
applications alike.
Device parameters may be presented with different structure each time;
as a single declaration string or several strings each describing
different parts of the declaration.
To simplify the use of this parsing facility, its parameters are made
variadic.
Signed-off-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
dpdk-procinfo, as a secondary process, cannot fetch stats for vdev.
This patch enables that by attaching the port from the shared data.
We also fill the eth dev ops, with only some ops works in secondary
process, for example, stats_get().
Note that, we still cannot Rx/Tx packets on the ports which do not
support multi-process.
Reported-by: Signed-off-by: Vipin Varghese <vipin.varghese@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Qi Zhang <qi.z.zhang@intel.com>
Change the prototype and the behavior of dev_ops->eth_mac_addr_set(): a
return code is added to notify the caller (librte_ether) if an error
occurred in the PMD.
The new default MAC address is now copied in dev->data->mac_addrs[0]
only if the operation is successful.
The patch also updates all the PMDs accordingly.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Aligning Mellanox SPDX copyrights to a single format.
In addition replace to SPDX licence files which were missed.
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Since we have support for the strlcpy function in DPDK, replace all
instances where a string is copied using snprintf.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Fail-safe dev_start() operation can be called by both the application
and the hot-plug alarm mechanism.
The installation of Rx interrupt are triggered from dev_start() in any
time it is called while actually the Rx interrupt should be installed
only by the application calls.
So, each plug-in event causes reinstallation which causes memory leak
and spoils the fail-safe Rx interrupt mechanism.
Trigger the Rx interrupt installation only when it does not exist.
Fixes: 9e0360aebf ("net/failsafe: register as Rx interrupt mode")
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
The type pthread_t is not portable because it is freely defined.
On Linux, it is an unsigned long int which can be printed with %l.
On FreeBSD, it is a pointer which can be printed with %p.
That's why there was this error:
drivers/net/failsafe/failsafe_private.h:377:53: error:
format specifies type 'unsigned long' but the argument has
type 'pthread_t' (aka 'struct pthread *')
Fixes: 655fcd68c7 ("net/failsafe: fix hotplug races")
Reported-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Tested-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Fail-safe PMD manages the states of its sub-devices gradually:
DEV_UNDEFINED, DEV_PARSED, DEV_PROBED, DEV_ACTIVE, DEV_STARTED.
When the sub-device arguments successfully was parsed, the state is
raised from DEV_UNDEFINED to DEV_PARSED.
When the sub-device successfully was probed, the state is raised from
DEV_PARSED to DEV_PROBED.
When the sub-device successfully was configured by
rte_eth_dev_configure(), the state is raised from DEV_PROBED to
DEV_ACTIVE.
When the sub-device successfully was started by rte_eth_dev_start(), the
state is raised from DEV_ACTIVE to DEV_STARTED.
When the sub-device successfully was stopped by rte_eth_dev_stop(), the
state is degraded from DEV_STARTED to DEV_ACTIVE.
When the sub-device successfully was closed by rte_eth_dev_close(), the
state is degraded from DEV_ACTIVE to DEV_PROBED.
When the sub-device successfully was removed by
rte_eal_hotplug_remove(), the state is degraded from DEV_PROBED to
DEV_UNDEFINED.
Fail-safe dev_configure() operation calls to its sub-devices
dev_configure() operation, but only for sub-devices which are in
DEV_PROBED state, means that sub-devices which are in DEV_ACTIVE state
because the application triggered dev_stop() operation cannot be
reconfigured again by dev_configure() operation which is really
problematic when application wants to reconfigure its ports.
Actually, the application may get success report when some of the
sub-devices are not in the wanted configuration.
The current behavior of fail-safe dev_configure() is correct only for
the first time dev_configure() is triggered by the application or for
sub-device synchronization in plug-in event, but it ignores the option
for reconfiguration from application side.
Allow calling to sub-devices dev_configure() operations also in
DEV_ACTIVE state when the call was triggered by the application.
Fixes: a46f8d584e ("net/failsafe: add fail-safe PMD")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Fail-safe uses a periodic alarm mechanism, running from the host
thread, to manage the hot-plug events of its sub-devices. This
management requires a lot of sub-devices PMDs operations
(stop, close, start, configure, etc.).
While the hot-plug alarm runs in the host thread, the application may
call fail-safe operations, which directly trigger the sub-devices PMDs
operations as well. This call may occur from any thread decided by the
application (probably the master thread).
Thus, more than one operation can be executed to a sub-device at the
same time. This can initiate a lot of races in the sub-PMDs.
Moreover, some control operations update the fail-safe internal
databases, which can be used by the alarm mechanism at the same time.
This can also initiate races and crashes.
Fail-safe is the owner of its sub-devices and must synchronize their
use according to the ETHDEV ownership rules.
Synchronize hot-plug management by a new lock mechanism uses a mutex to
atomically defend each critical section in the fail-safe hot-plug
mechanism and control operations to prevent any races between them.
Fixes: a46f8d5 ("net/failsafe: add fail-safe PMD")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
The fail-safe PMD uses a per sub-device flag called "remove" to
indicate the scope where the sub-device was removed physically and
whether its software resources should be released.
This flag is set when the fail-safe receives an RMV notification
about the physical removal of the sub-device, and should be unset when
all the sub-device resources are released.
The previous code wrongly unsets the flag in dev_configure(), instead
of when the software resources release is completed.
Change the remove flag unsetting to take action in the end of the
software resources release.
Fixes: a46f8d5 ("net/failsafe: add fail-safe PMD")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
The hot-plug alarm mechanism of fail-safe PMD is responsible for
handling removed devices during a plug-out event and to restore them
back to activity following a plug-in event.
Fail-safe sets a flag called "pending_alarm" to validate that only one
alarm callback is pending at any time. While this flag is required to
avoid simultaneous initiations of the alarm thread - it should not be
considered during alarm thread cancellation.
So, when failsafe_hotplug_alarm_cancel() was called while the alarm
callback was being executed the alarm mechanism was not stopped.
Skip checking the "pending_alarm" flag to allow alarm thread
cancellation all the times.
Fixes: ebea83f899 ("net/failsafe: add plug-in support")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Failsafe reported Tx offloads capabilities are the AND result of its
default capabilities and those of its sub-devices.
In the corrupted code failsafe default Tx capabilities were set to 0.
As a result when running testpmd with "--tx-offloads=0x8000" parameter
(request for multi segments offload) - an error was returned:
PMD: net_failsafe:
Some Tx offloads are not supported, requested 0x8000 supported 0x0
To fix this, failsafe default Tx offload capabilities are set to
DEV_TX_OFFLOAD_MULTI_SEGS |
DEV_TX_OFFLOAD_IPV4_CKSUM |
DEV_TX_OFFLOAD_UDP_CKSUM |
DEV_TX_OFFLOAD_TCP_CKSUM,
Fixes: a46f8d584e ("net/failsafe: add fail-safe PMD")
Cc: stable@dpdk.org
Signed-off-by: Ophir Munk <ophirmu@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Fail-safe PMD sub devices management is based on ethdev port mechanism.
So, the sub-devices management structures are exposed to other DPDK
entities which may use them in parallel to fail-safe PMD.
Use the new port ownership mechanism to avoid multiple managments of
fail-safe PMD sub-devices.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Call dedicated ethdev API to free port in remove time as was done in
other fail-safe places.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
This patch is the last patch in the series of patches aimed
to add support for registering and waiting for Rx interrupts
in failsafe PMD. This allows applications to wait for Rx events
from the PMD using the DPDK rte_epoll subsystem.
The failsafe PMD presents to the application a facade of a single
device to be handled by the application while internally it manages
several devices on behalf of the application including packets
transmission and reception.
The Proposed failsafe Rx interrupt scheme follows this approach.
The failsafe PMD will present the application with a single set of
Rx interrupt vectors representing the failsafe Rx queues, while
internally it will serve as an interrupt proxy for its subdevices.
will allow applications to wait for Rx traffic from the failsafe
PMD by registering and waiting for Rx events from its Rx queues.
In order to support this the following is suggested:
* Every Rx queue in the failsafe (virtual) device will be assigned
* a Linux event file descriptor (efd) and an enable_interrupts flag.
* The failsafe PMD will fill in its rte_intr_handle structure with
the Rx efds assigned previously and register them with the EAL.
* The failsafe driver will create a private epoll fd (epfd) and
* will allocate enough space to handle all the Rx events from all its
subdevices.
* Acting as an application,
for each Rx queue in each active subdevice the failsafe will:
o Register the Rx queue with the EAL.
o Pass the EAL the failsafe private epoll fd as the epfd to
register the Rx queue event on.
o Pass the EAL, as a parameter, the pointer to the failsafe Rx
queue that handles this Rx queue.
o Using the DPDK service callbacks, the failsafe PMD will launch
an Rx proxy service that will Wait on the epoll fd for Rx
events from the sub-devices.
o For each Rx event received the proxy service will
- Retrieve the pointer to failsafe Rx queue that handles
this subdevice Rx queue from the user info returned by the
EAL.
- Trigger a failsafe Rx event on that queue by writing to
the event fd unless interrupts are disabled for that queue.
* The failsafe pmd will also implement the rx_queue_intr_enable
* and rx_queue_intr_disable routines that will enable and disable Rx
interrupts respectively on both on the failsafe and its subdevices.
Signed-off-by: Moti Haimovsky <motih@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
This commit adds the following functionality to failsafe PMD:
* Register and unregister slaves Rx interrupts.
* Enable and Disable slaves Rx interrupts.
The interrupts events generated by the slaves are not handled in this
commit.
Signed-off-by: Moti Haimovsky <motih@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
This patch adds registering the Rx queues of the failsafe PMD with EAL
Rx interrupts subsystem.
Each failsafe RX queue is assigned with a unique eventfd and an enable
interrupts flag.
The PMD creates an interrupt vector containing the above eventfds and
Registers it with EAL. The PMD also implements the Rx interrupts enable
and disable interface routines.
This patch does not implement the generation of Rx interrupts, so an
application can now wait for failsafe Rx interrupts but it will not
receive one.
Signed-off-by: Moti Haimovsky <motih@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
In case of plugged out device, the fail-safe PMD uses failsafe_rx_burst
function for packet receiving.
This function iterates over the present sub-devices until it
receives a traffic from one of them or they are all cannot receive
packets.
The corrupted code didn't advance the sub-device pointer when the
sub-device was not present and caused to infinite loop.
Advance the sub-device pointer also in plugged-out sub-device case.
Fixes: 8052bbd9d5 ("net/failsafe: improve Rx sub-devices iteration")
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Add checks during build to ensure that all symbols in the EXPERIMENTAL
version map section have __experimental tags on their definitions, and
enable the warnings needed to announce their use. Also add an
ALLOW_EXPERIMENTAL_APIS define to allow individual libraries and files
to declare the acceptability of experimental api usage
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Create a rte_ethdev_driver.h file and move PMD specific APIs here.
Drivers updated to include this new header file.
There is no update in header content and since ethdev.h included by
ethdev_driver.h, nothing changed from driver point of view, only
logically grouping of APIs. From applications point of view they can't
access to driver specific APIs anymore and they shouldn't.
More PMD specific data structures still remain in ethdev.h because of
inline functions in header use them. Those will be handled separately.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
There is time between the physical removal of the device until
sub-device PMDs get a RMV interrupt. At this time DPDK PMDs and
applications still don't know about the removal and may call sub-device
control operation which should return an error.
In previous code this error is reported to the application contrary to
fail-safe principle that the app should not be aware of device removal.
Add an removal check in each relevant control command error flow and
prevent an error report to application when the sub-device is removed.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Previous fail-safe code didn't support probed sub-devices capture and
failed when it tried to probe them.
Skip fail-safe sub-device probing when it already was probed.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
rte_free() is not supposed to work with pointers returned by calloc().
Fixes: a0194d8281 ("net/failsafe: add flexible device definition")
Cc: stable@dpdk.org
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Ethdev Rx offloads API has changed since:
commit ce17eddefc ("ethdev: introduce Rx queue offloads API")
This commit adds support for the new Rx offloads API.
Signed-off-by: Moti Haimovsky <motih@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Ethdev Tx offloads API has changed since:
commit cba7f53b71 ("ethdev: introduce Tx queue offloads API")
This commit adds support for the new Tx offloads API.
Signed-off-by: Moti Haimovsky <motih@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Connecting the sub-devices each other by cyclic linked list can help to
iterate over them by Rx burst functions because there is no need to
check the sub-devices ring wraparound.
Create the aforementioned linked-list and change the Rx burst functions
iteration accordingly.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Fail-safe uses atomic operations to protect sub-device close operation
calling by host thread in removal time while the removed sub-device
burst functions are still in process by application threads.
Using "set" atomic operations is a little bit more efficient than "add"
or "sub" atomic operations because "set" shouldn't read the value and
in fact, it does not need a special atomic mechanism in x86 platforms.
Replace "add 1" and "sub 1" atomic operations by "set 1" and "set 0"
atomic operations.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
failsafe_rx_burst function is used when there are no sub-devices or at
least one of them has been removed, on the other hand, when all the
sub-devices are present, failsafe_rx_burst_fast function is used.
So it's really expected that some of the sub-devices will be unsafe for
Rx burst in failsafe_rx_burst execution.
Remove unlikely compiler hint from fs_rx_unsafe calling.
Fixes: a46f8d584e ("net/failsafe: add fail-safe PMD")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Gaetan Rivet <gaetan.rivet@6wind.com>
The pointer to the user parameter of the callback registration is
automatically pass to the callback function.
There is no point to allow changing this user parameter by a caller.
That's why this parameter is always set to NULL by PMDs and set only
in ethdev layer before calling the callback function.
The history is that the user parameter was initially used
by the callback implementation to pass some information
between the application and the driver:
c1ceaf3ad0 ("ethdev: add an argument to internal callback function")
Then a new parameter has been added to leave the user parameter
to its standard usage of context given at registration:
d6af1a13d7 ("ethdev: add return values to callback process API")
The NULL parameter in the internal callback processing function
is now removed. It makes clear that the callback parameter is user
managed and opaque from a DPDK point of view.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
There are 3 kind of link data in ethdev:
- capabilities (rte_eth_dev_info)
- configuration (rte_eth_conf)
- status (rte_eth_link)
A bit-field is used for capabilities (rte_eth_dev_info.speed_capa) and
configuration (rte_eth_conf.link_speeds).
Bits are defined in ETH_LINK_SPEED_*.
Some numerical (ETH_SPEED_NUM_*) and boolean (ETH_LINK_*) values
are used for the link status (rte_eth_link.*).
There was a mistake in the comment of rte_eth_link.link_autoneg,
suggesting ETH_LINK_SPEED_[AUTONEG/FIXED] which are 0/1,
instead of ETH_LINK_[AUTONEG/FIXED] which are 1/0.
The drivers are fixed to use ETH_LINK_[AUTONEG/FIXED].
Fixes: 82113036e4 ("ethdev: redesign link speed config")
Suggested-by: Andrew Rybchenko <arybchenko@solarflare.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Move the vdev bus from lib/librte_eal to drivers/bus.
As the crypto vdev helper function refers to data structure
in rte_vdev.h, so we move those helper function into drivers/bus
too.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
failsafe device has vlan stripping configured at startup however once
a sub device is found as non-capable of vlan-stripping failsafe
updates it configuration and removes vlan stripping from it.
This update occurs only once at startup. Following a later plugin
attempt and in case of vlan stripping mismatch between failsafe
configuration and device capability - failsafe cannot recover and the
device remains constantly in plug out state.
The sequence of events leading to this situation is described as
follows:
1. Start testpmd with failsafe where mlx4 is a sub device (not capable
of vlan stripping). Expected printout:
PMD: net_failsafe: Disabling VLAN stripping offload
2. Execute:
testpmd> port stop all
testpmd> port config all max-pkt-len 2048
testpmd> port start all
3. Do a plug out (e.g. disable sriov)
4. Do a plug in (e.g. enable sriov)
5. Expected result: failsafe successfully configures and starts its sub
devices
Actual result: failsafe is continuously failing with these messages:
PMD: net_failsafe: VLAN stripping offload requested but not supported by
sub_device 0
PMD: net_failsafe: device already configured, cannot fix live
configuration
PMD: net_failsafe: Unable to synchronize sub device state
Root cause analysis: at startup failsafe removes vlan stripping from its
configuration. After executing "port config all max-pkt-len 2048"
testpmd marks failsafe in need for configuration update.
After executing "port start all" testpmd overrides failsafe
configuration with its own configuration which includes vlan stripping
During the plugin attempt failsafe refuses to update its configuration
by removing vlan stripping since it has already updated its
configuration at startup.
The fix is for failsafe to stop validation and disabling non-supported
offloads in its sub-devices.
Fixes: bbc6a53dda ("net/failsafe: support Rx offload capabilities")
Cc: stable@dpdk.org
Signed-off-by: Ophir Munk <ophirmu@mellanox.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
