The rte_vdev_driver is declared twice.
The first one is not necessary.
Fixes: 050fe6e9ff ("drivers/net: use ethdev allocation helper for vdev")
Cc: stable@dpdk.org
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Transmit errors must not be reported in q_errors[] which is for
reception.
Fixes: c743e50c47 ("null: new poll mode driver")
Cc: stable@dpdk.org
Signed-off-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add 'rte_' prefix to structures:
- rename struct ether_addr as struct rte_ether_addr.
- rename struct ether_hdr as struct rte_ether_hdr.
- rename struct vlan_hdr as struct rte_vlan_hdr.
- rename struct vxlan_hdr as struct rte_vxlan_hdr.
- rename struct vxlan_gpe_hdr as struct rte_vxlan_gpe_hdr.
Do not update the command line library to avoid adding a dependency to
librte_net.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
After previous changes, the function rte_eth_dev_release_port()
can be used for primary or secondary process as well.
The only difference with rte_eth_dev_release_port_secondary()
is the shared lock used in rte_eth_dev_release_port().
The function rte_eth_dev_release_port_secondary() was recently
added in 18.11 cycle.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
This is a clean-up of common ethdev data freeing.
All data freeing are moved to rte_eth_dev_release_port()
and done only in case of primary process.
It is probably fixing some memory leaks for PMDs which were
not freeing all data.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Attach port from secondary should ignore devargs since the private
device is not necessary to support. Also previously, detach port on
a secondary process will mess primary process and cause the same
device can't be attached back again. A secondary process should use
rte_eth_dev_release_port_secondary to release a port.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Removed DEV_RX_OFFLOAD_CRC_STRIP offload flag.
Without any specific Rx offload flag, default behavior by PMDs is to
strip CRC.
PMDs that support keeping CRC should advertise DEV_RX_OFFLOAD_KEEP_CRC
Rx offload capability.
Applications that require keeping CRC should check PMD capability first
and if it is supported can enable this feature by setting
DEV_RX_OFFLOAD_KEEP_CRC in Rx offload flag in rte_eth_dev_configure()
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Tomasz Duszynski <tdu@semihalf.com>
Acked-by: Shahaf Shuler <shahafs@mellanox.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Jan Remes <remes@netcope.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Calling rte_eth_dev_info_get() on secondary process cause a crash
because eth_dev->device is not set properly.
Fixes: ee27edbe0c ("drivers/net: share vdev data to secondary process")
Cc: stable@dpdk.org
Reported-by: Vipin Varghese <vipin.varghese@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Qi Zhang <qi.z.zhang@intel.com>
A constructor is usually declared with RTE_INIT* macros.
As it is a static function, no need to declare before its definition.
The macro is used directly in the function definition.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
DEV_RX_OFFLOAD_KEEP_CRC offload flag is added. PMDs that support
keeping CRC should advertise this offload capability.
DEV_RX_OFFLOAD_CRC_STRIP flag will remain one more release
default behavior in PMDs are to keep the CRC until this flag removed
Until DEV_RX_OFFLOAD_CRC_STRIP flag is removed:
- Setting both KEEP_CRC & CRC_STRIP is INVALID
- Setting only CRC_STRIP PMD should strip the CRC
- Setting only KEEP_CRC PMD should keep the CRC
- Not setting both PMD should keep the CRC
A helper function rte_eth_dev_is_keep_crc() has been added to be able to
change the no flag behavior with minimal changes in PMDs.
The PMDs that doesn't report the DEV_RX_OFFLOAD_KEEP_CRC offload can
remove rte_eth_dev_is_keep_crc() checks next release, related code
commented to help the maintenance task.
And DEV_RX_OFFLOAD_CRC_STRIP has been added to virtual drivers since
they don't use CRC at all, when an application requires this offload
virtual PMDs should not return error.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Allain Legacy <allain.legacy@windriver.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
A new hook function is added and called inside the PMDs at the end
of the device probing:
- in primary process, after allocating, init and config
- in secondary process, after attaching and local init
This new function is almost empty for now.
It will be used later to add some post-initialization processing.
For the PMDs calling the helpers rte_eth_dev_create() or
rte_eth_dev_pci_generic_probe(), the hook rte_eth_dev_probing_finish()
is called from here, and not in the PMD itself.
Note that the helper rte_eth_dev_create() could be used more,
especially for vdevs, avoiding some code duplication in PMDs.
Cc: stable@dpdk.org
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Convert null device to use dynamic logging.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
These drivers never attempt link speed negotiation. Change link_autoneg
value to ETH_LINK_FIXED to be more accurate and consistent between PMDs.
Fixes: 1e3a958f40 ("ethdev: fix link autonegotiation value")
Cc: stable@dpdk.org
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
dpdk-procinfo, as a secondary process, cannot fetch stats for vdev.
This patch enables that by attaching the port from the shared data.
We also fill the eth dev ops, with only some ops works in secondary
process, for example, stats_get().
Note that, we still cannot Rx/Tx packets on the ports which do not
support multi-process.
Reported-by: Signed-off-by: Vipin Varghese <vipin.varghese@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Qi Zhang <qi.z.zhang@intel.com>
We introduced private rte_eth_dev_data to allow vdev to be created
both in primary process and secondary process(es). This is not
friendly to multi-process model, for example, it leads to port id
contention issue if two processes both find the data entry is free.
And to get stats of primary vdev in secondary, we must allocate
from the pre-defined array so that we can find it.
Suggested-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Qi Zhang <qi.z.zhang@intel.com>
Change the prototype and the behavior of dev_ops->eth_mac_addr_set(): a
return code is added to notify the caller (librte_ether) if an error
occurred in the PMD.
The new default MAC address is now copied in dev->data->mac_addrs[0]
only if the operation is successful.
The patch also updates all the PMDs accordingly.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Previously all null devices were getting MAC address "00:00:00:00:00:00"
After attaching two Null device to OVS, seeing "00.00.00.00.00.00" mac
address for both null devices.
Fix this issue, by setting different mac address.
Signed-off-by: Mallesh Koujalagi <malleshx.koujalagi@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Fixes: efd5d1a8d8 ("drivers/net: build some vdev PMDs with meson")
Cc: stable@dpdk.org
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Add the af_packet, null, pcap and ring PMDs to the meson build.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Keith Wiles <keith.wiles@intel.com>
Acked-by: Luca Boccassi <luca.boccassi@gmail.com>
Create a rte_ethdev_driver.h file and move PMD specific APIs here.
Drivers updated to include this new header file.
There is no update in header content and since ethdev.h included by
ethdev_driver.h, nothing changed from driver point of view, only
logically grouping of APIs. From applications point of view they can't
access to driver specific APIs anymore and they shouldn't.
More PMD specific data structures still remain in ethdev.h because of
inline functions in header use them. Those will be handled separately.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
There are 3 kind of link data in ethdev:
- capabilities (rte_eth_dev_info)
- configuration (rte_eth_conf)
- status (rte_eth_link)
A bit-field is used for capabilities (rte_eth_dev_info.speed_capa) and
configuration (rte_eth_conf.link_speeds).
Bits are defined in ETH_LINK_SPEED_*.
Some numerical (ETH_SPEED_NUM_*) and boolean (ETH_LINK_*) values
are used for the link status (rte_eth_link.*).
There was a mistake in the comment of rte_eth_link.link_autoneg,
suggesting ETH_LINK_SPEED_[AUTONEG/FIXED] which are 0/1,
instead of ETH_LINK_[AUTONEG/FIXED] which are 1/0.
The drivers are fixed to use ETH_LINK_[AUTONEG/FIXED].
Fixes: 82113036e4 ("ethdev: redesign link speed config")
Suggested-by: Andrew Rybchenko <arybchenko@solarflare.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Move the vdev bus from lib/librte_eal to drivers/bus.
As the crypto vdev helper function refers to data structure
in rte_vdev.h, so we move those helper function into drivers/bus
too.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
This flag is not necessary at the ether layer anymore.
Buses are able to advertise their hotplug support. The ether layer can
rely upon this capability instead of a special flag.
Signed-off-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
The list of libraries in LDLIBS was generated from the DEPDIRS-xyz
variable. This is valid when the subdirectory name match the library
name, but it's not always the case, especially for PMDs.
The patches removes this feature and explicitly adds the proper
libraries in LDLIBS.
Some DEPDIRS-xyz variables become useless, remove them.
Reported-by: Gage Eads <gage.eads@intel.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
The stats_get dev op API doesn't include return value, so PMD cannot
return an error in case of failure at stats getting process time.
Since PCI devices can be removed and there is a time between the
physical removal to the RMV interrupt, the user may get invalid stats
without any indication.
This patch changes the stats_get API return value to be int instead of
void.
All the net PMDs stats_get dev ops are adjusted by this patch.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Extend port_id definition from uint8_t to uint16_t in lib and drivers
data structures, specifically rte_eth_dev_data. Modify the APIs,
drivers and app using port_id at the same time.
Fix some checkpatch issues from the original code and remove some
unnecessary cast operations.
release_17_11 and deprecation docs have been updated in this patch.
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Virtual device/driver probing done via name.
A new alternative method introduced to probe the device with providing
driver name in devargs as "driver=<driver_name>".
This patch removes alternative method and fixes virtual device usages
with proper device names.
Fixes: 87c3bf29c6 ("test: do not short-circuit null device creation")
Fixes: d39670086a ("eal: parse driver argument before probing drivers")
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
mbuf next and nb_segs fields already have the default values when get
from mempool, no need to update them in PMD.
See: 8f094a9ac5 ("mbuf: set mbuf fields while in pool")
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Olivier Matz <olivier.matz@6wind.com>
There is no need to export this API. Remaining users should use the
rte_eal_vdev_init() function instead.
Signed-off-by: Jan Blunck <jblunck@infradead.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
A virtual device should get initialized through the rte_eal_vdev_init()
function to properly initialize the driver.
Signed-off-by: Jan Blunck <jblunck@infradead.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
This is a preparation to embed the generic rte_device into the rte_eth_dev
also for virtual devices.
Signed-off-by: Jan Blunck <jblunck@infradead.org>
Signed-off-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Now that the m->next pointer and m->nb_segs is expected to be set (to
NULL and 1 respectively) after a mempool_get(), we can avoid to write them
in the Rx functions of drivers.
Only some drivers are patched, it's not an exhaustive patch. It gives
the idea to do the same in other drivers.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Before this patch, the management of dependencies between directories
had several issues:
- the generation of .depdirs, done at configuration is slow: it can take
more than one minute on some slow targets (usually ~10s on a standard
PC without -j).
- for instance, it is possible to express a dependency like:
- app/foo depends on lib/librte_foo
- and lib/librte_foo depends on app/bar
But this won't work because the directories are traversed with a
depth-first algorithm, so we have to choose between doing 'app' before
or after 'lib'.
- the script depdirs-rule.sh is too complex.
- we cannot use "make -d" for debug, because the output of make is used for
the generation of .depdirs.
This patch moves the DEPDIRS-* variables in the upper Makefile, making
the dependencies much easier to calculate. A DEPDIRS variable is still
used to process library dependencies in LDLIBS.
After this commit, "make config" is almost immediate.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Tested-by: Robin Jarry <robin.jarry@6wind.com>
Tested-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Some virtual pmds report a different name than the vdev driver name
registered in eal.
While it does not hurt, let's try to be consistent.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Since commit b1fb53a39d ("ethdev: remove some PCI specific handling"),
rte_eth_dev_info_get() relies on dev->data->drv_name to report the driver
name to caller.
Having the pmds set driver_info->driver_name in the pmds is useless,
since ethdev overwrites it right after.
The only thing the pmd must do is:
- for pci drivers, call rte_eth_copy_pci_info() which then sets
data->drv_name
- for vdev drivers, manually set data->drv_name
At this stage, virtio-user does not properly report a driver name (fixed in
next commit).
Signed-off-by: David Marchand <david.marchand@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Jan Blunck <jblunck@infradead.org>
Since rte_eth_dev_info_get does memset() on dev_info before
calling device specific code, the explicit assignment of NULL
in all these virtual drivers has no effect.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jan Blunck <jblunck@infradead.org>
This moves the non-PCI related initialization of the link state interrupt
callback list and the setting of the default MTU to rte_eth_dev_allocate()
so that drivers only need to set non-default values.
Signed-off-by: Jan Blunck <jblunck@infradead.org>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This registers the legacy names of the driver being renamed in
commit 2f45703c17 ("drivers: make driver names consistent").
Signed-off-by: Jan Blunck <jblunck@infradead.org>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
All macros related to driver registeration renamed from DRIVER_*
to RTE_PMD_*
This includes:
DRIVER_REGISTER_PCI -> RTE_PMD_REGISTER_PCI
DRIVER_REGISTER_PCI_TABLE -> RTE_PMD_REGISTER_PCI_TABLE
DRIVER_REGISTER_VDEV -> RTE_PMD_REGISTER_VDEV
DRIVER_REGISTER_PARAM_STRING -> RTE_PMD_REGISTER_PARAM_STRING
DRIVER_EXPORT_* -> RTE_PMD_EXPORT_*
Fix PMDINFOGEN tool to look for matches of RTE_PMD_REGISTER_*.
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Inline with PCI probe and remove, VDEV probe and remove hooks provide
a uniform naming.
PCI probe represents scan and driver initialization. For VDEV, it will
represent argument parsing and initialization.
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
- All devices register themselfs by calling a kind of DRIVER_REGISTER_XXX.
The PMD_REGISTER_DRIVER is not used anymore.
- PMD_VDEV type is also not being used - can be removed from all VDEVs.
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
All PMD_VDEV drivers can now use rte_vdev_driver instead of the
rte_driver (which is embedded in the rte_vdev_driver).
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
Now that hotplug has been moved to eal, there is no reason to keep the
device type in this layer.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
As discussed in the past release, driver names are modified
to be more consistent, and the future driver should follow
this new convention.
Driver names consist of:
"driver category"_"driver folder name"_"optional extra name".
For example:
- Crypto null driver -> "crypto_null"
- Network IXGBE VF driver -> "net_ixgbe_vf"
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
