1. ln_en bit should not be turned on, since we only support Rx VEB.
2. lan_en bit need to be turned on for a DCF switch rule, otherwise
any Tx packet that hit on a rule will be dropped.
Fixes: fed0c5ca5f ("net/ice/base: support programming a new switch recipe")
Cc: stable@dpdk.org
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
After VF reset, FDIR rule still takes effect. To solve the issue,
this patch adds to flush all flows before flow uninit. VIRTCHNL
sends message to PF by Admin Queue, so flow flush should be implemented
before Admin Queue shut down.
Fixes: ff2d0c345c ("net/iavf: support generic flow API")
Signed-off-by: Simei Su <simei.su@intel.com>
Acked-by: Xiaolong Ye <xiaolong.ye@intel.com>
When we flush FDIR filter, we can not call i40e_fdir_teardown()
function as it will free vsi used for FDIR, then the vsi->base_queue
will be freed from pf->qp_pool, but vsi->base_queue can only get
once when do dev init in i40e_pf_setup(). If we free it, it will
never be alloc again.
Bugzilla ID: 404
Fixes: 2e67a7fbf3 ("net/i40e: config flow director automatically")
Cc: stable@dpdk.org
Signed-off-by: Wei Zhao <wei.zhao1@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Each PCTYPE can only have one specific FDIR input set at one time.
Add input set requirement info to i40e doc.
Bugzilla ID: 403
Fixes: 14c66a451e ("net/i40e: flush tunnel filters")
Cc: stable@dpdk.org
Signed-off-by: Wei Zhao <wei.zhao1@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Currently, flow "pattern eth type is 0x0806 / end actions mark id
0x86 / rss / end" can't be created successfully. FDIR parser
shouldn't deny RTE_ETHER_TYPE_ARP since ARP packets will be
parsed as PCTYPE_L2_PAYLOAD. This patch fixes the issue.
Bugzilla ID: 402
Fixes: 42044b69c6 ("net/i40e: support input set selection for FDIR")
Cc: stable@dpdk.org
Signed-off-by: Wei Zhao <wei.zhao1@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Ideally a rule with "TO VSI LIST" action should not be deleted when one
of the VF reset happens. The correct action by kernel PF driver is to
remove the VSI of a reset VF from the VSI list, but this is not
implemented in kernel PF yet, so workaround is the DCF to prevent a
rule with "To VSI List" action happens.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Reviewed-by: Wei Zhao <wei.zhao1@intel.com>
Updated the params list to include flush timer, this will
allow users to set the HW flush timer value in 10th of second.
Setting 0 will disable the pending cache flush feature.
Signed-off-by: Shahaji Bhosle <sbhosle@broadcom.com>
Signed-off-by: Randy Schacher <stuart.schacher@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The ulp required to be changed to properly call the index table
management routines and use the index for external memory indices.
The ulp no longer has to account for stride as the tf_core returns the
actual offset, not a 0 based index.
Signed-off-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Reviewed-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
- Added support variable sized action records
- Additional error checking on table scope params
- Single external pool supported per direction
- Changed to return action record pointer
- Allows action pool to fully utilize the number of flows
Signed-off-by: Farah Smith <farah.smith@broadcom.com>
Signed-off-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Peter Spreadborough <peter.spreadborough@broadcom.com>
Reviewed-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
The resource function did not have a method of invalidating or
indicating that a resource is uninitialized. Added an invalid enum so
that processing works correctly for partially added flows.
Signed-off-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Max Rx Ring count could be < Max stat contexts. While accounting
for stat contexts, this should be also considered and
the max ring count adjusted accordingly.
Fixes: f03e66cb64 ("net/bnxt: limit queue count for NS3/Stingray devices")
Cc: stable@dpdk.org
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Building DPDK on Ubuntu 20.04 with GCC 9.3.0 results in a "subscript is
outside array bounds" message in rte_memcpy function. The build error
is caused by an interaction between __builtin_constant_p and
"-Werror=array-bounds" as described in this bugzilla:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=90387
Modify the code to disable the array-bounds check for GCC versions 9.0
to 9.3.
Cc: stable@dpdk.org
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
The behavior of strtok_r() is not the same between GNU libc and FreeBSD
libc: in the first case, the context is set to "" when the last token is
returned, while in the second case it is set to NULL.
On FreeBSD, the current code crashes because we are dereferencing a NULL
pointer (ctx1). Fix it by first checking if it is NULL. This works with
both GNU and FreeBSD libc.
Fixes: ffcf831454 ("kvargs: fix buffer overflow when parsing list")
Cc: stable@dpdk.org
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Tested-by: Zhimin Huang <zhiminx.huang@intel.com>
Prevent from writing beyond the allocated memory.
GCC 10 compiling output:
eal_common_trace_utils.c: In function 'eal_trace_dir_args_save':
eal_common_trace_utils.c:290:24: error: '__builtin___sprintf_chk' \
may write a terminating nul past the end of the destination \
[-Werror=format-overflow=]
290 | sprintf(dir_path, "%s/", optarg);
| ^
Fixes: 8af866df8d ("trace: add trace directory configuration parameter")
Signed-off-by: Phil Yang <phil.yang@arm.com>
Reviewed-by: Lijian Zhang <lijian.zhang@arm.com>
Tested-by: Lijian Zhang <lijian.zhang@arm.com>
Acked-by: Sunil Kumar Kori <skori@marvell.com>
Signed-off-by: David Marchand <david.marchand@redhat.com>
There is nothing performance sensitive in this list, use dynamic
allocations and remove the arbitrary limit on the number of trace
patterns a user can pass.
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Sunil Kumar Kori <skori@marvell.com>
The trace framework can be configured via 4 EAL options:
- --trace which calls eal_trace_args_save,
- --trace-dir which calls eal_trace_dir_args_save,
- --trace-bufsz which calls eal_trace_bufsz_args_save,
- --trace-mode which calls eal_trace_mode_args_save.
Those 4 internal callbacks are getting passed a non NULL value:
optarg won't be NULL since those options are declared with
required_argument (man getopt_long).
eal_trace_bufsz_args_save() already trusted passed value, align the other
3 internal callbacks.
Coverity issue: 357768
Fixes: 8c8066ea6a ("trace: add trace mode configuration parameter")
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Sunil Kumar Kori <skori@marvell.com>
Prefer a local name to optarg which is a global symbol from the C library.
Fixes: 8c8066ea6a ("trace: add trace mode configuration parameter")
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Sunil Kumar Kori <skori@marvell.com>
Invert the current trace point headers logic by making
rte_trace_point_register.h include rte_trace_point.h.
There is no more need for a RTE_TRACE_POINT_REGISTER_SELECT special macro
since including rte_trace_point_register.h itself means we want to
register trace points.
The unexplained "provider" notion is removed from the documentation and
rte_trace_point_provider.h is merged into rte_trace_point.h.
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Those trace points are defined but not registered.
Fixes: 4cf30e3f3c ("cryptodev: add tracepoints")
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Sunil Kumar Kori <skori@marvell.com>
The AltiVec header file breaks boolean type. [1] [2]
Currently the workaround was located only in mlx5 device.
Adding the trace module caused this issue to appear again, due to
order of includes, it keeps overriding the local fix.
This patch solves this issue by resetting the bool type, immediately
after it is being changed.
[1] https://mails.dpdk.org/archives/dev/2018-August/110281.html
[2]
In file included from
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:18:0,
from
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool.h:54,
from
dpdk/drivers/common/mlx5/mlx5_common_mr.c:7:
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h: In
function '__rte_trace_point_fp_is_enabled':
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:226:2:
error: incompatible types when returning type 'int' but '__vector __bool
int' was expected
return false;
^
In file included from
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:281:0,
from
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:18,
from
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool.h:54,
from
dpdk/drivers/common/mlx5/mlx5_common_mr.c:7:
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:
In function 'rte_mempool_trace_ops_dequeue_bulk':
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point_provider.h:104:6:
error: wrong type argument to unary exclamation mark
if (!__rte_trace_point_fp_is_enabled()) \
^
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:49:2:
note: in expansion of macro '__rte_trace_point_emit_header_fp'
__rte_trace_point_emit_header_##_mode(&__##_tp); \
^
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:99:2:
note: in expansion of macro '__RTE_TRACE_POINT'
__RTE_TRACE_POINT(fp, tp, args, __VA_ARGS__)
^
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:20:1:
note: in expansion of macro 'RTE_TRACE_POINT_FP'
RTE_TRACE_POINT_FP(
^
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:
In function 'rte_mempool_trace_ops_dequeue_contig_blocks':
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point_provider.h:104:6:
error: wrong type argument to unary exclamation mark
if (!__rte_trace_point_fp_is_enabled()) \
^
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:49:2:
note: in expansion of macro '__rte_trace_point_emit_header_fp'
__rte_trace_point_emit_header_##_mode(&__##_tp); \
^
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:99:2:
note: in expansion of macro '__RTE_TRACE_POINT'
__RTE_TRACE_POINT(fp, tp, args, __VA_ARGS__)
^
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:29:1:
note: in expansion of macro 'RTE_TRACE_POINT_FP'
RTE_TRACE_POINT_FP(
^
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:
In function 'rte_mempool_trace_ops_enqueue_bulk':
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point_provider.h:104:6:
error: wrong type argument to unary exclamation mark
if (!__rte_trace_point_fp_is_enabled()) \
Fixes: 725f5dd0bf ("net/mlx5: fix build on PPC64")
Signed-off-by: Ori Kam <orika@mellanox.com>
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Tested-by: David Christensen <drc@linux.vnet.ibm.com>
Tested-by: Raslan Darawsheh <rasland@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
stringop-overflow warns when it sees a possible overflow
in a string operation.
In the rte_memcpy functions different branches are taken
depending on the size. stringop-overflow is raised for the
branches in the function where it sees the static size of the
src could be overflowed.
However, in reality a correct size argument and in some cases
dynamic allocation would ensure that this does not happen.
For example, in the case below for key, the correct path will be
chosen in rte_memcpy_generic at runtime based on the size argument
but as some paths in the function could lead to a cast to 32 bytes
a warning is raised.
In function ‘_mm256_storeu_si256’,
inlined from ‘rte_memcpy_generic’
at ../lib/librte_eal/common/include/arch/x86/rte_memcpy.h:315:2,
inlined from ‘iavf_configure_rss_key’
at ../lib/librte_eal/common/include/arch/x86/rte_memcpy.h:869:10:
/usr/lib/gcc/x86_64-redhat-linux/10/include/avxintrin.h:928:8:
warning: writing 32 bytes into a region of size 1 [-Wstringop-overflow=]
928 | *__P = __A;
| ~~~~~^~~~~
In file included
from ../drivers/net/iavf/../../common/iavf/iavf_prototype.h:10,
from ../drivers/net/iavf/iavf.h:9,
from ../drivers/net/iavf/iavf_vchnl.c:22:
../drivers/net/iavf/iavf_vchnl.c:
In function ‘iavf_configure_rss_key’:
../drivers/net/iavf/../../common/iavf/virtchnl.h:508:5:
note: at offset 0 to object ‘key’ with size 1 declared here
508 | u8 key[1]; /* RSS hash key, packed bytes */
| ^~~
Ignore the stringop-overflow warnings for rte_memcpy.h functions.
Bugzilla ID: 394
Bugzilla ID: 421
Cc: stable@dpdk.org
Signed-off-by: Kevin Traynor <ktraynor@redhat.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
gcc 10.0.1 reports:
../examples/ipsec-secgw/ipsec_process.c: In function ‘ipsec_process’:
../examples/ipsec-secgw/ipsec_process.c:132:34:
error: ‘grp.m’ may be used uninitialized in this function
[-Werror=maybe-uninitialized]
132 | grp[n].cnt = pkts + i - grp[n].m;
| ~~~~~~^~
This is a correct warning for the initial execution of the statement.
However, it is the design of the loop that grp[0].cnt will later be
written with the correct value using an initialized grp[0].m before it
is used.
In order to remove the warning, initialize grp[0].m for the initial and
unused calculation of grp[0].cnt.
Fixes: 3e5f4625dc ("examples/ipsec-secgw: make data-path to use IPsec library")
Cc: stable@dpdk.org
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Kevin Traynor <ktraynor@redhat.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
gcc 10.0.1 reports:
../drivers/net/avp/avp_ethdev.c: In function ‘avp_xmit_scattered_pkts’:
../drivers/net/avp/avp_ethdev.c:1791:24:
warning: ‘avp_bufs[count]’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
1791 | tx_bufs[i] = avp_bufs[count];
| ~~~~~~~~^~~~~~~
../drivers/net/avp/avp_ethdev.c:1791:24:
warning: ‘avp_bufs[count]’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
Fix by initializing the array.
Fixes: 295abce2d2 ("net/avp: add packet transmit functions")
Cc: stable@dpdk.org
Signed-off-by: Kevin Traynor <ktraynor@redhat.com>
Acked-by: Steven Webster <steven.webster@windriver.com>
Adding programmer's guide for Graph library and the inbuilt nodes.
This patch also updates the release note for the new libraries.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Add graph creation, configuration logic and graph main loop.
This graph main loop is run on every slave lcore and calls
rte_graph_walk() to walk over lcore specific rte_graph.
Master core accumulates and prints graph walk stats of all the
lcore's graph's.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Add changes to ethdev port and queue configuration based
on command line parameters for l3fwd graph application.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Add graph based l3fwd application skeleton with cmdline
parsing support inline with normal l3fwd.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Add packet drop node process function for pkt_drop
rte_node. This node simply free's every object received as
an rte_mbuf to its rte_pktmbuf pool.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Add ip4_rewrite and ip4_lookup ctrl API. ip4_lookup ctrl
API is used to add route entries for LPM lookup with
result data containing next hop id and next proto.
ip4_rewrite ctrl API is used to add rewrite data for
every next hop.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Add ip4 rewrite process function for ip4_rewrite
rte_node. On every packet received by this node,
header is overwritten with new data before forwarding
it to next node. Header data to overwrite with is
identified by next hop id passed in mbuf priv data
by previous node.
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Add IPv4 lookup process function for ip4_lookup
rte_node. This node performs LPM lookup using x86_64
vector supported RTE_LPM API on every packet received
and forwards it to a next node that is identified by
lookup result.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Add arm64 specific IPv4 lookup process function
for ip4_lookup node. This node performs LPM lookup
on every packet received and forwards it to a next
node that is identified by lookup result.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Add IPv4 lookup process function for ip4_lookup node.
This node performs LPM lookup using simple RTE_LPM API on every packet
received and forwards it to a next node that is identified by lookup
result.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Add ctrl api to setup ethdev_rx and ethdev_tx node.
This ctrl api clones 'N' number of ethdev_rx and ethdev_tx
nodes with specific (port, queue) pairs updated in their context.
All the ethdev ports and queues are setup before this api
is called.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Add rte_node ethdev_tx process function and register it to
graph infra. This node has a specific (port, tx-queue) as context
and it enqueue's all the packets received to that specific queue pair.
When rte_eth_tx_burst() i.e enqueue to queue pair fails, packets
are forwarded to pkt_drop node to be free'd.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Add source rte_node ethdev_rx process function and register
it. This node is a source node that will be called periodically
and when called, performs rte_eth_rx_burst() on a specific
(port, queue) pair and enqueue them as stream of objects to
next node.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Add log infra for node specific logging.
Also, add null rte_node that just ignores all the objects
directed to it.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Add unit test framework to create and test performance of various
graph models.
example command to test:
echo "graph_perf_autotest" | sudo ./build/app/test/dpdk-test -c 0x30
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding the unit test to test the functionality of node and graph APIs.
Testing includes registering a node, cloning a node, creating a graph,
perform graph walk, collecting stats and all node and graph debug APIs.
example command to test:
echo "graph_autotest" | sudo ./build/app/test/dpdk-test -c 0x30
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding implementation for rte_graph_walk() API. This will perform a walk
on the circular buffer and call the process function of each node
and collect the stats if stats collection is enabled.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding implementation for graph stats collection API. This API will
create a cluster for a specified node pattern and aggregate the node
runtime stats.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding implementation for graph specific API to dump the
Graph information to a file. This API will dump detailed internal
info about node objects and graph objects.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding API implementation support exporting the graph object to file.
This will export the graph to a file in Graphviz format.
It can be viewed in many viewers such as
https://dreampuf.github.io/GraphvizOnline/
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding support for graph specific API implementation like
Graph lookup to get graph object, retrieving graph ID
From name and graph name from ID.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding graph specific API implementations like graph create
and graph destroy. This detect loops in the graph,
check for isolated nodes and operation to verify the validity of
graph.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding support to create and populate the memory for graph reel.
This includes reserving the memory in the memzone, populating the nodes,
Allocating memory for node-specific streams to hold objects.
Once it is populated the reel memory contains the following sections.
+---------------------+
| Graph Header |
+---------------------+
| Fence |
+---------------------+
| Circular buffer |
+---------------------+
| Fence |
+---------------------+
| Node Object 0 |
+------------------- -+
| Node Object 1 |
+------------------- -+
| Node Object 2 |
+------------------- -+
| Node Object n |
+------------------- -+
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding internal graph API helpers support to check whether a graph has
isolated nodes and any node have a loop to itself and BFS
algorithm implementation etc.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding node debug API implementation support to dump
single or all the node objects to the given file.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
