.. BSD LICENSE Copyright (c) 2015 QLogic Corporation All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. * Neither the name of QLogic Corporation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. BNX2X Poll Mode Driver ====================== The BNX2X poll mode driver library (**librte_pmd_bnx2x**) implements support for **QLogic 578xx** 10/20 Gbps family of adapters as well as their virtual functions (VF) in SR-IOV context. It is supported on several standard Linux distros like Red Hat 7.x and SLES12 OS. It is compile-tested under FreeBSD OS. More information can be found at `QLogic Corporation's Official Website `_. Supported Features ------------------ BNX2X PMD has support for: - Base L2 features - Unicast/multicast filtering - Promiscuous mode - Port hardware statistics - SR-IOV VF Non-supported Features ---------------------- The features not yet supported include: - TSS (Transmit Side Scaling) - RSS (Receive Side Scaling) - LRO/TSO offload - Checksum offload - SR-IOV PF - Rx TX scatter gather Co-existence considerations --------------------------- - BCM578xx being a CNA can have both NIC and Storage personalities. However, coexistence with storage protocol drivers (cnic, bnx2fc and bnx2fi) is not supported on the same adapter. So storage personality has to be disabled on that adapter when used in DPDK applications. - For SR-IOV case, bnx2x PMD will be used to bind to SR-IOV VF device and Linux native kernel driver (bnx2x) will be attached to SR-IOV PF. Supported QLogic NICs --------------------- - 578xx Prerequisites ------------- - Requires firmware version **7.2.51.0**. It is included in most of the standard Linux distros. If it is not available visit `linux-firmware git repository `_ to get the required firmware. Pre-Installation Configuration ------------------------------ Config File Options ~~~~~~~~~~~~~~~~~~~ The following options can be modified in the ``.config`` file. Please note that enabling debugging options may affect system performance. - ``CONFIG_RTE_LIBRTE_BNX2X_PMD`` (default **n**) Toggle compilation of bnx2x driver. To use bnx2x PMD set this config parameter to 'y'. Also, in order for firmware binary to load user will need zlib devel package installed. - ``CONFIG_RTE_LIBRTE_BNX2X_DEBUG_TX`` (default **n**) Toggle display of transmit fast path run-time messages. - ``CONFIG_RTE_LIBRTE_BNX2X_DEBUG_RX`` (default **n**) Toggle display of receive fast path run-time messages. - ``CONFIG_RTE_LIBRTE_BNX2X_DEBUG_PERIODIC`` (default **n**) Toggle display of register reads and writes. .. _bnx2x_driver-compilation: Driver compilation and testing ------------------------------ Refer to the document :ref:`compiling and testing a PMD for a NIC ` for details. SR-IOV: Prerequisites and sample Application Notes -------------------------------------------------- This section provides instructions to configure SR-IOV with Linux OS. #. Verify SR-IOV and ARI capabilities are enabled on the adapter using ``lspci``: .. code-block:: console lspci -s -vvv Example output: .. code-block:: console [...] Capabilities: [1b8 v1] Alternative Routing-ID Interpretation (ARI) [...] Capabilities: [1c0 v1] Single Root I/O Virtualization (SR-IOV) [...] Kernel driver in use: igb_uio #. Load the kernel module: .. code-block:: console modprobe bnx2x Example output: .. code-block:: console systemd-udevd[4848]: renamed network interface eth0 to ens5f0 systemd-udevd[4848]: renamed network interface eth1 to ens5f1 #. Bring up the PF ports: .. code-block:: console ifconfig ens5f0 up ifconfig ens5f1 up #. Create VF device(s): Echo the number of VFs to be created into "sriov_numvfs" sysfs entry of the parent PF. Example output: .. code-block:: console echo 2 > /sys/devices/pci0000:00/0000:00:03.0/0000:81:00.0/sriov_numvfs #. Assign VF MAC address: Assign MAC address to the VF using iproute2 utility. The syntax is: ip link set vf mac Example output: .. code-block:: console ip link set ens5f0 vf 0 mac 52:54:00:2f:9d:e8 #. PCI Passthrough: The VF devices may be passed through to the guest VM using virt-manager or virsh etc. bnx2x PMD should be used to bind the VF devices in the guest VM using the instructions outlined in the Application notes below. #. Running testpmd: (Supply ``--log-level="pmd.net.bnx2x.driver",7`` to view informational messages): Follow instructions available in the document :ref:`compiling and testing a PMD for a NIC ` to run testpmd. Example output: .. code-block:: console [...] EAL: PCI device 0000:84:00.0 on NUMA socket 1 EAL: probe driver: 14e4:168e rte_bnx2x_pmd EAL: PCI memory mapped at 0x7f14f6fe5000 EAL: PCI memory mapped at 0x7f14f67e5000 EAL: PCI memory mapped at 0x7f15fbd9b000 EAL: PCI device 0000:84:00.1 on NUMA socket 1 EAL: probe driver: 14e4:168e rte_bnx2x_pmd EAL: PCI memory mapped at 0x7f14f5fe5000 EAL: PCI memory mapped at 0x7f14f57e5000 EAL: PCI memory mapped at 0x7f15fbd4f000 Interactive-mode selected Configuring Port 0 (socket 0) PMD: bnx2x_dev_tx_queue_setup(): fp[00] req_bd=512, thresh=512, usable_bd=1020, total_bd=1024, tx_pages=4 PMD: bnx2x_dev_rx_queue_setup(): fp[00] req_bd=128, thresh=0, usable_bd=510, total_bd=512, rx_pages=1, cq_pages=8 PMD: bnx2x_print_adapter_info(): [...] Checking link statuses... Port 0 Link Up - speed 10000 Mbps - full-duplex Port 1 Link Up - speed 10000 Mbps - full-duplex Done testpmd>