de34aaa96b
The tool dpdk-hugepages.py, added in DPDK 20.11, is referenced in the guides instead of more complicate commands. The original Linux commands are kept in linux_gsg/sys_reqs.rst and nics/build_and_test.rst. Suggested-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Thomas Monjalon <thomas@monjalon.net> Acked-by: Stephen Hemminger <stephen@networkplumber.org>
568 lines
22 KiB
ReStructuredText
568 lines
22 KiB
ReStructuredText
.. SPDX-License-Identifier: BSD-3-Clause
|
|
Copyright(c) 2010-2015 Intel Corporation.
|
|
|
|
Poll Mode Driver for Emulated Virtio NIC
|
|
========================================
|
|
|
|
Virtio is a para-virtualization framework initiated by IBM, and supported by KVM hypervisor.
|
|
In the Data Plane Development Kit (DPDK),
|
|
we provide a virtio Poll Mode Driver (PMD) as a software solution, comparing to SRIOV hardware solution,
|
|
for fast guest VM to guest VM communication and guest VM to host communication.
|
|
|
|
Vhost is a kernel acceleration module for virtio qemu backend.
|
|
The DPDK extends kni to support vhost raw socket interface,
|
|
which enables vhost to directly read/ write packets from/to a physical port.
|
|
With this enhancement, virtio could achieve quite promising performance.
|
|
|
|
For basic qemu-KVM installation and other Intel EM poll mode driver in guest VM,
|
|
please refer to Chapter "Driver for VM Emulated Devices".
|
|
|
|
In this chapter, we will demonstrate usage of virtio PMD driver with two backends,
|
|
standard qemu vhost back end and vhost kni back end.
|
|
|
|
Virtio Implementation in DPDK
|
|
-----------------------------
|
|
|
|
For details about the virtio spec, refer to the latest
|
|
`VIRTIO (Virtual I/O) Device Specification
|
|
<https://www.oasis-open.org/committees/tc_home.php?wg_abbrev=virtio>`_.
|
|
|
|
As a PMD, virtio provides packet reception and transmission callbacks.
|
|
|
|
In Rx, packets described by the used descriptors in vring are available
|
|
for virtio to burst out.
|
|
|
|
In Tx, packets described by the used descriptors in vring are available
|
|
for virtio to clean. Virtio will enqueue to be transmitted packets into
|
|
vring, make them available to the device, and then notify the host back
|
|
end if necessary.
|
|
|
|
Features and Limitations of virtio PMD
|
|
--------------------------------------
|
|
|
|
In this release, the virtio PMD driver provides the basic functionality of packet reception and transmission.
|
|
|
|
* It supports merge-able buffers per packet when receiving packets and scattered buffer per packet
|
|
when transmitting packets. The packet size supported is from 64 to 1518.
|
|
|
|
* It supports multicast packets and promiscuous mode.
|
|
|
|
* The descriptor number for the Rx/Tx queue is hard-coded to be 256 by qemu 2.7 and below.
|
|
If given a different descriptor number by the upper application,
|
|
the virtio PMD generates a warning and fall back to the hard-coded value.
|
|
Rx queue size can be configurable and up to 1024 since qemu 2.8 and above. Rx queue size is 256
|
|
by default. Tx queue size is still hard-coded to be 256.
|
|
|
|
* Features of mac/vlan filter are supported, negotiation with vhost/backend are needed to support them.
|
|
When backend can't support vlan filter, virtio app on guest should not enable vlan filter in order
|
|
to make sure the virtio port is configured correctly. E.g. do not specify '--enable-hw-vlan' in testpmd
|
|
command line. Note that, mac/vlan filter is best effort: unwanted packets could still arrive.
|
|
|
|
* "RTE_PKTMBUF_HEADROOM" should be defined
|
|
no less than "sizeof(struct virtio_net_hdr_mrg_rxbuf)", which is 12 bytes when mergeable or
|
|
"VIRTIO_F_VERSION_1" is set.
|
|
no less than "sizeof(struct virtio_net_hdr)", which is 10 bytes, when using non-mergeable.
|
|
|
|
* Virtio does not support runtime configuration.
|
|
|
|
* Virtio supports Link State interrupt.
|
|
|
|
* Virtio supports Rx interrupt (so far, only support 1:1 mapping for queue/interrupt).
|
|
|
|
* Virtio supports software vlan stripping and inserting.
|
|
|
|
* Virtio supports using port IO to get PCI resource when uio/igb_uio module is not available.
|
|
|
|
Prerequisites
|
|
-------------
|
|
|
|
The following prerequisites apply:
|
|
|
|
* In the BIOS, turn VT-x and VT-d on
|
|
|
|
* Linux kernel with KVM module; vhost module loaded and ioeventfd supported.
|
|
Qemu standard backend without vhost support isn't tested, and probably isn't supported.
|
|
|
|
Virtio with kni vhost Back End
|
|
------------------------------
|
|
|
|
This section demonstrates kni vhost back end example setup for Phy-VM Communication.
|
|
|
|
.. _figure_host_vm_comms:
|
|
|
|
.. figure:: img/host_vm_comms.*
|
|
|
|
Host2VM Communication Example Using kni vhost Back End
|
|
|
|
|
|
Host2VM communication example
|
|
|
|
#. Load the kni kernel module:
|
|
|
|
.. code-block:: console
|
|
|
|
insmod rte_kni.ko
|
|
|
|
Other basic DPDK preparations like hugepage enabling, uio port binding are not listed here.
|
|
Please refer to the *DPDK Getting Started Guide* for detailed instructions.
|
|
|
|
#. Launch the kni user application:
|
|
|
|
.. code-block:: console
|
|
|
|
<build_dir>/examples/dpdk-kni -l 0-3 -n 4 -- -p 0x1 -P --config="(0,1,3)"
|
|
|
|
This command generates one network device vEth0 for physical port.
|
|
If specify more physical ports, the generated network device will be vEth1, vEth2, and so on.
|
|
|
|
For each physical port, kni creates two user threads.
|
|
One thread loops to fetch packets from the physical NIC port into the kni receive queue.
|
|
The other user thread loops to send packets in the kni transmit queue.
|
|
|
|
For each physical port, kni also creates a kernel thread that retrieves packets from the kni receive queue,
|
|
place them onto kni's raw socket's queue and wake up the vhost kernel thread to exchange packets with the virtio virt queue.
|
|
|
|
For more details about kni, please refer to :ref:`kni`.
|
|
|
|
#. Enable the kni raw socket functionality for the specified physical NIC port,
|
|
get the generated file descriptor and set it in the qemu command line parameter.
|
|
Always remember to set ioeventfd_on and vhost_on.
|
|
|
|
Example:
|
|
|
|
.. code-block:: console
|
|
|
|
echo 1 > /sys/class/net/vEth0/sock_en
|
|
fd=`cat /sys/class/net/vEth0/sock_fd`
|
|
exec qemu-system-x86_64 -enable-kvm -cpu host \
|
|
-m 2048 -smp 4 -name dpdk-test1-vm1 \
|
|
-drive file=/data/DPDKVMS/dpdk-vm.img \
|
|
-netdev tap, fd=$fd,id=mynet_kni, script=no,vhost=on \
|
|
-device virtio-net-pci,netdev=mynet_kni,bus=pci.0,addr=0x3,ioeventfd=on \
|
|
-vnc:1 -daemonize
|
|
|
|
In the above example, virtio port 0 in the guest VM will be associated with vEth0, which in turns corresponds to a physical port,
|
|
which means received packets come from vEth0, and transmitted packets is sent to vEth0.
|
|
|
|
#. In the guest, bind the virtio device to the uio_pci_generic kernel module and start the forwarding application.
|
|
When the virtio port in guest bursts Rx, it is getting packets from the
|
|
raw socket's receive queue.
|
|
When the virtio port bursts Tx, it is sending packet to the tx_q.
|
|
|
|
.. code-block:: console
|
|
|
|
modprobe uio
|
|
dpdk-hugepages.py --setup 1G
|
|
modprobe uio_pci_generic
|
|
./usertools/dpdk-devbind.py -b uio_pci_generic 00:03.0
|
|
|
|
We use testpmd as the forwarding application in this example.
|
|
|
|
.. figure:: img/console.*
|
|
|
|
Running testpmd
|
|
|
|
#. Use IXIA packet generator to inject a packet stream into the KNI physical port.
|
|
|
|
The packet reception and transmission flow path is:
|
|
|
|
IXIA packet generator->82599 PF->KNI Rx queue->KNI raw socket queue->Guest
|
|
VM virtio port 0 Rx burst->Guest VM virtio port 0 Tx burst-> KNI Tx queue
|
|
->82599 PF-> IXIA packet generator
|
|
|
|
Virtio with qemu virtio Back End
|
|
--------------------------------
|
|
|
|
.. _figure_host_vm_comms_qemu:
|
|
|
|
.. figure:: img/host_vm_comms_qemu.*
|
|
|
|
Host2VM Communication Example Using qemu vhost Back End
|
|
|
|
|
|
.. code-block:: console
|
|
|
|
qemu-system-x86_64 -enable-kvm -cpu host -m 2048 -smp 2 -mem-path /dev/
|
|
hugepages -mem-prealloc
|
|
-drive file=/data/DPDKVMS/dpdk-vm1
|
|
-netdev tap,id=vm1_p1,ifname=tap0,script=no,vhost=on
|
|
-device virtio-net-pci,netdev=vm1_p1,bus=pci.0,addr=0x3,ioeventfd=on
|
|
-device pci-assign,host=04:10.1 \
|
|
|
|
In this example, the packet reception flow path is:
|
|
|
|
IXIA packet generator->82599 PF->Linux Bridge->TAP0's socket queue-> Guest
|
|
VM virtio port 0 Rx burst-> Guest VM 82599 VF port1 Tx burst-> IXIA packet
|
|
generator
|
|
|
|
The packet transmission flow is:
|
|
|
|
IXIA packet generator-> Guest VM 82599 VF port1 Rx burst-> Guest VM virtio
|
|
port 0 Tx burst-> tap -> Linux Bridge->82599 PF-> IXIA packet generator
|
|
|
|
|
|
Virtio PMD Rx/Tx Callbacks
|
|
--------------------------
|
|
|
|
Virtio driver has 6 Rx callbacks and 3 Tx callbacks.
|
|
|
|
Rx callbacks:
|
|
|
|
#. ``virtio_recv_pkts``:
|
|
Regular version without mergeable Rx buffer support for split virtqueue.
|
|
|
|
#. ``virtio_recv_mergeable_pkts``:
|
|
Regular version with mergeable Rx buffer support for split virtqueue.
|
|
|
|
#. ``virtio_recv_pkts_vec``:
|
|
Vector version without mergeable Rx buffer support, also fixes the available
|
|
ring indexes and uses vector instructions to optimize performance for split
|
|
virtqueue.
|
|
|
|
#. ``virtio_recv_pkts_inorder``:
|
|
In-order version with mergeable and non-mergeable Rx buffer support
|
|
for split virtqueue.
|
|
|
|
#. ``virtio_recv_pkts_packed``:
|
|
Regular and in-order version without mergeable Rx buffer support for
|
|
packed virtqueue.
|
|
|
|
#. ``virtio_recv_mergeable_pkts_packed``:
|
|
Regular and in-order version with mergeable Rx buffer support for packed
|
|
virtqueue.
|
|
|
|
Tx callbacks:
|
|
|
|
#. ``virtio_xmit_pkts``:
|
|
Regular version for split virtqueue.
|
|
|
|
#. ``virtio_xmit_pkts_inorder``:
|
|
In-order version for split virtqueue.
|
|
|
|
#. ``virtio_xmit_pkts_packed``:
|
|
Regular and in-order version for packed virtqueue.
|
|
|
|
By default, the non-vector callbacks are used:
|
|
|
|
* For Rx: If mergeable Rx buffers is disabled then ``virtio_recv_pkts``
|
|
or ``virtio_recv_pkts_packed`` will be used, otherwise
|
|
``virtio_recv_mergeable_pkts`` or ``virtio_recv_mergeable_pkts_packed``
|
|
will be used.
|
|
|
|
* For Tx: ``virtio_xmit_pkts`` or ``virtio_xmit_pkts_packed`` will be used.
|
|
|
|
|
|
Vector callbacks will be used when:
|
|
|
|
* Mergeable Rx buffers is disabled.
|
|
|
|
The corresponding callbacks are:
|
|
|
|
* For Rx: ``virtio_recv_pkts_vec``.
|
|
|
|
There is no vector callbacks for packed virtqueue for now.
|
|
|
|
|
|
Example of using the vector version of the virtio poll mode driver in
|
|
``testpmd``::
|
|
|
|
dpdk-testpmd -l 0-2 -n 4 -- -i --rxq=1 --txq=1 --nb-cores=1
|
|
|
|
In-order callbacks only work on simulated virtio user vdev.
|
|
|
|
For split virtqueue:
|
|
|
|
* For Rx: If in-order is enabled then ``virtio_recv_pkts_inorder`` is used.
|
|
|
|
* For Tx: If in-order is enabled then ``virtio_xmit_pkts_inorder`` is used.
|
|
|
|
For packed virtqueue, the default callbacks already support the
|
|
in-order feature.
|
|
|
|
Interrupt mode
|
|
--------------
|
|
|
|
.. _virtio_interrupt_mode:
|
|
|
|
There are three kinds of interrupts from a virtio device over PCI bus: config
|
|
interrupt, Rx interrupts, and Tx interrupts. Config interrupt is used for
|
|
notification of device configuration changes, especially link status (lsc).
|
|
Interrupt mode is translated into Rx interrupts in the context of DPDK.
|
|
|
|
.. Note::
|
|
|
|
Virtio PMD already has support for receiving lsc from qemu when the link
|
|
status changes, especially when vhost user disconnects. However, it fails
|
|
to do that if the VM is created by qemu 2.6.2 or below, since the
|
|
capability to detect vhost user disconnection is introduced in qemu 2.7.0.
|
|
|
|
Prerequisites for Rx interrupts
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
To support Rx interrupts,
|
|
#. Check if guest kernel supports VFIO-NOIOMMU:
|
|
|
|
Linux started to support VFIO-NOIOMMU since 4.8.0. Make sure the guest
|
|
kernel is compiled with:
|
|
|
|
.. code-block:: console
|
|
|
|
CONFIG_VFIO_NOIOMMU=y
|
|
|
|
#. Properly set msix vectors when starting VM:
|
|
|
|
Enable multi-queue when starting VM, and specify msix vectors in qemu
|
|
cmdline. (N+1) is the minimum, and (2N+2) is mostly recommended.
|
|
|
|
.. code-block:: console
|
|
|
|
$(QEMU) ... -device virtio-net-pci,mq=on,vectors=2N+2 ...
|
|
|
|
#. In VM, insert vfio module in NOIOMMU mode:
|
|
|
|
.. code-block:: console
|
|
|
|
modprobe vfio enable_unsafe_noiommu_mode=1
|
|
modprobe vfio-pci
|
|
|
|
#. In VM, bind the virtio device with vfio-pci:
|
|
|
|
.. code-block:: console
|
|
|
|
./usertools/dpdk-devbind.py -b vfio-pci 00:03.0
|
|
|
|
Example
|
|
~~~~~~~
|
|
|
|
Here we use l3fwd-power as an example to show how to get started.
|
|
|
|
Example:
|
|
|
|
.. code-block:: console
|
|
|
|
$ dpdk-l3fwd-power -l 0-1 -- -p 1 -P --config="(0,0,1)" \
|
|
--no-numa --parse-ptype
|
|
|
|
|
|
Virtio PMD arguments
|
|
--------------------
|
|
|
|
Below devargs are supported by the PCI virtio driver:
|
|
|
|
#. ``vdpa``:
|
|
|
|
A virtio device could also be driven by vDPA (vhost data path acceleration)
|
|
driver, and works as a HW vhost backend. This argument is used to specify
|
|
a virtio device needs to work in vDPA mode.
|
|
(Default: 0 (disabled))
|
|
|
|
#. ``speed``:
|
|
|
|
It is used to specify link speed of virtio device. Link speed is a part of
|
|
link status structure. It could be requested by application using
|
|
rte_eth_link_get_nowait function.
|
|
(Default: 0xffffffff (Unknown))
|
|
|
|
#. ``vectorized``:
|
|
|
|
It is used to specify whether virtio device prefers to use vectorized path.
|
|
Afterwards, dependencies of vectorized path will be checked in path
|
|
election.
|
|
(Default: 0 (disabled))
|
|
|
|
Below devargs are supported by the virtio-user vdev:
|
|
|
|
#. ``path``:
|
|
|
|
It is used to specify a path to connect to vhost backend.
|
|
|
|
#. ``mac``:
|
|
|
|
It is used to specify the MAC address.
|
|
|
|
#. ``cq``:
|
|
|
|
It is used to enable the control queue. (Default: 0 (disabled))
|
|
|
|
#. ``queue_size``:
|
|
|
|
It is used to specify the queue size. (Default: 256)
|
|
|
|
#. ``queues``:
|
|
|
|
It is used to specify the queue number. (Default: 1)
|
|
|
|
#. ``iface``:
|
|
|
|
It is used to specify the host interface name for vhost-kernel
|
|
backend.
|
|
|
|
#. ``server``:
|
|
|
|
It is used to enable the server mode when using vhost-user backend.
|
|
(Default: 0 (disabled))
|
|
|
|
#. ``mrg_rxbuf``:
|
|
|
|
It is used to enable virtio device mergeable Rx buffer feature.
|
|
(Default: 1 (enabled))
|
|
|
|
#. ``in_order``:
|
|
|
|
It is used to enable virtio device in-order feature.
|
|
(Default: 1 (enabled))
|
|
|
|
#. ``packed_vq``:
|
|
|
|
It is used to enable virtio device packed virtqueue feature.
|
|
(Default: 0 (disabled))
|
|
|
|
#. ``speed``:
|
|
|
|
It is used to specify link speed of virtio device. Link speed is a part of
|
|
link status structure. It could be requested by application using
|
|
rte_eth_link_get_nowait function.
|
|
(Default: 0xffffffff (Unknown))
|
|
|
|
#. ``vectorized``:
|
|
|
|
It is used to specify whether virtio device prefers to use vectorized path.
|
|
Afterwards, dependencies of vectorized path will be checked in path
|
|
election.
|
|
(Default: 0 (disabled))
|
|
|
|
Virtio paths Selection and Usage
|
|
--------------------------------
|
|
|
|
Logically virtio-PMD has 9 paths based on the combination of virtio features
|
|
(Rx mergeable, In-order, Packed virtqueue), below is an introduction of these
|
|
features:
|
|
|
|
* `Rx mergeable <https://docs.oasis-open.org/virtio/virtio/v1.1/cs01/
|
|
virtio-v1.1-cs01.html#x1-2140004>`_: With this feature negotiated, device
|
|
can receive large packets by combining individual descriptors.
|
|
* `In-order <https://docs.oasis-open.org/virtio/virtio/v1.1/cs01/
|
|
virtio-v1.1-cs01.html#x1-690008>`_: Some devices always use descriptors
|
|
in the same order in which they have been made available, these
|
|
devices can offer the VIRTIO_F_IN_ORDER feature. With this feature negotiated,
|
|
driver will use descriptors in order.
|
|
* `Packed virtqueue <https://docs.oasis-open.org/virtio/virtio/v1.1/cs01/
|
|
virtio-v1.1-cs01.html#x1-610007>`_: The structure of packed virtqueue is
|
|
different from split virtqueue, split virtqueue is composed of available ring,
|
|
used ring and descriptor table, while packed virtqueue is composed of descriptor
|
|
ring, driver event suppression and device event suppression. The idea behind
|
|
this is to improve performance by avoiding cache misses and make it easier
|
|
for hardware to implement.
|
|
|
|
Virtio paths Selection
|
|
~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
If packed virtqueue is not negotiated, below split virtqueue paths will be selected
|
|
according to below configuration:
|
|
|
|
#. Split virtqueue mergeable path: If Rx mergeable is negotiated, in-order feature is
|
|
not negotiated, this path will be selected.
|
|
#. Split virtqueue non-mergeable path: If Rx mergeable and in-order feature are not
|
|
negotiated, also Rx offload(s) are requested, this path will be selected.
|
|
#. Split virtqueue in-order mergeable path: If Rx mergeable and in-order feature are
|
|
both negotiated, this path will be selected.
|
|
#. Split virtqueue in-order non-mergeable path: If in-order feature is negotiated and
|
|
Rx mergeable is not negotiated, this path will be selected.
|
|
#. Split virtqueue vectorized Rx path: If Rx mergeable is disabled and no Rx offload
|
|
requested, this path will be selected.
|
|
|
|
If packed virtqueue is negotiated, below packed virtqueue paths will be selected
|
|
according to below configuration:
|
|
|
|
#. Packed virtqueue mergeable path: If Rx mergeable is negotiated, in-order feature
|
|
is not negotiated, this path will be selected.
|
|
#. Packed virtqueue non-mergeable path: If Rx mergeable and in-order feature are not
|
|
negotiated, this path will be selected.
|
|
#. Packed virtqueue in-order mergeable path: If in-order and Rx mergeable feature are
|
|
both negotiated, this path will be selected.
|
|
#. Packed virtqueue in-order non-mergeable path: If in-order feature is negotiated and
|
|
Rx mergeable is not negotiated, this path will be selected.
|
|
#. Packed virtqueue vectorized Rx path: If building and running environment support
|
|
(AVX512 || NEON) && in-order feature is negotiated && Rx mergeable
|
|
is not negotiated && TCP_LRO Rx offloading is disabled && vectorized option enabled,
|
|
this path will be selected.
|
|
#. Packed virtqueue vectorized Tx path: If building and running environment support
|
|
(AVX512 || NEON) && in-order feature is negotiated && vectorized option enabled,
|
|
this path will be selected.
|
|
|
|
Rx/Tx callbacks of each Virtio path
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
Refer to above description, virtio path and corresponding Rx/Tx callbacks will
|
|
be selected automatically. Rx callbacks and Tx callbacks for each virtio path
|
|
are shown in below table:
|
|
|
|
.. table:: Virtio Paths and Callbacks
|
|
|
|
============================================ ================================= ========================
|
|
Virtio paths Rx callbacks Tx callbacks
|
|
============================================ ================================= ========================
|
|
Split virtqueue mergeable path virtio_recv_mergeable_pkts virtio_xmit_pkts
|
|
Split virtqueue non-mergeable path virtio_recv_pkts virtio_xmit_pkts
|
|
Split virtqueue in-order mergeable path virtio_recv_pkts_inorder virtio_xmit_pkts_inorder
|
|
Split virtqueue in-order non-mergeable path virtio_recv_pkts_inorder virtio_xmit_pkts_inorder
|
|
Split virtqueue vectorized Rx path virtio_recv_pkts_vec virtio_xmit_pkts
|
|
Packed virtqueue mergeable path virtio_recv_mergeable_pkts_packed virtio_xmit_pkts_packed
|
|
Packed virtqueue non-meregable path virtio_recv_pkts_packed virtio_xmit_pkts_packed
|
|
Packed virtqueue in-order mergeable path virtio_recv_mergeable_pkts_packed virtio_xmit_pkts_packed
|
|
Packed virtqueue in-order non-mergeable path virtio_recv_pkts_packed virtio_xmit_pkts_packed
|
|
Packed virtqueue vectorized Rx path virtio_recv_pkts_packed_vec virtio_xmit_pkts_packed
|
|
Packed virtqueue vectorized Tx path virtio_recv_pkts_packed virtio_xmit_pkts_packed_vec
|
|
============================================ ================================= ========================
|
|
|
|
Virtio paths Support Status from Release to Release
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
Virtio feature implementation:
|
|
|
|
* In-order feature is supported since DPDK 18.08 by adding new Rx/Tx callbacks
|
|
``virtio_recv_pkts_inorder`` and ``virtio_xmit_pkts_inorder``.
|
|
* Packed virtqueue is supported since DPDK 19.02 by adding new Rx/Tx callbacks
|
|
``virtio_recv_pkts_packed`` , ``virtio_recv_mergeable_pkts_packed`` and
|
|
``virtio_xmit_pkts_packed``.
|
|
|
|
All virtio paths support status are shown in below table:
|
|
|
|
.. table:: Virtio Paths and Releases
|
|
|
|
============================================ ============= ============= ============= =======
|
|
Virtio paths 16.11 ~ 18.05 18.08 ~ 18.11 19.02 ~ 19.11 20.05 ~
|
|
============================================ ============= ============= ============= =======
|
|
Split virtqueue mergeable path Y Y Y Y
|
|
Split virtqueue non-mergeable path Y Y Y Y
|
|
Split virtqueue vectorized Rx path Y Y Y Y
|
|
Split virtqueue simple Tx path Y N N N
|
|
Split virtqueue in-order mergeable path Y Y Y
|
|
Split virtqueue in-order non-mergeable path Y Y Y
|
|
Packed virtqueue mergeable path Y Y
|
|
Packed virtqueue non-mergeable path Y Y
|
|
Packed virtqueue in-order mergeable path Y Y
|
|
Packed virtqueue in-order non-mergeable path Y Y
|
|
Packed virtqueue vectorized Rx path Y
|
|
Packed virtqueue vectorized Tx path Y
|
|
============================================ ============= ============= ============= =======
|
|
|
|
QEMU Support Status
|
|
~~~~~~~~~~~~~~~~~~~
|
|
|
|
* Qemu now supports three paths of split virtqueue: Split virtqueue mergeable path,
|
|
Split virtqueue non-mergeable path, Split virtqueue vectorized Rx path.
|
|
* Since qemu 4.2.0, Packed virtqueue mergeable path and Packed virtqueue non-mergeable
|
|
path can be supported.
|
|
|
|
How to Debug
|
|
~~~~~~~~~~~~
|
|
|
|
If you meet performance drop or some other issues after upgrading the driver
|
|
or configuration, below steps can help you identify which path you selected and
|
|
root cause faster.
|
|
|
|
#. Run vhost/virtio test case;
|
|
#. Run "perf top" and check virtio Rx/Tx callback names;
|
|
#. Identify which virtio path is selected refer to above table.
|