33e71acf3d
As per the deprecation notice, In the view of enabling unified driver for octeontx2(cn9k)/octeontx3(cn10k), removing drivers/octeontx2 drivers and replace with drivers/cnxk/ which supports both octeontx2(cn9k) and octeontx3(cn10k) SoCs. This patch does the following - Replace drivers/common/octeontx2/ with drivers/common/cnxk/ - Replace drivers/mempool/octeontx2/ with drivers/mempool/cnxk/ - Replace drivers/net/octeontx2/ with drivers/net/cnxk/ - Replace drivers/event/octeontx2/ with drivers/event/cnxk/ - Replace drivers/crypto/octeontx2/ with drivers/crypto/cnxk/ - Rename config/arm/arm64_octeontx2_linux_gcc as config/arm/arm64_cn9k_linux_gcc - Update the documentation and MAINTAINERS to reflect the same. - Change the reference to OCTEONTX2 as OCTEON 9. Old release notes and the kernel related documentation is not accounted for this change. Signed-off-by: Jerin Jacob <jerinj@marvell.com> Acked-by: Ferruh Yigit <ferruh.yigit@intel.com> Acked-by: Akhil Goyal <gakhil@marvell.com> Acked-by: Ruifeng Wang <ruifeng.wang@arm.com>
596 lines
17 KiB
ReStructuredText
596 lines
17 KiB
ReStructuredText
.. SPDX-License-Identifier: BSD-3-Clause
|
|
Copyright(c) 2016 Intel Corporation.
|
|
|
|
dpdk-test-crypto-perf Application
|
|
=================================
|
|
|
|
The ``dpdk-test-crypto-perf`` tool is a Data Plane Development Kit (DPDK)
|
|
utility that allows measuring performance parameters of PMDs available in the
|
|
crypto tree. There are available two measurement types: throughput and latency.
|
|
User can use multiply cores to run tests on but only
|
|
one type of crypto PMD can be measured during single application
|
|
execution. Cipher parameters, type of device, type of operation and
|
|
chain mode have to be specified in the command line as application
|
|
parameters. These parameters are checked using device capabilities
|
|
structure.
|
|
|
|
Limitations
|
|
-----------
|
|
On hardware devices the cycle-count doesn't always represent the actual offload
|
|
cost. The cycle-count only represents the offload cost when the hardware
|
|
accelerator is not fully loaded, when loaded the cpu cycles freed up by the
|
|
offload are still consumed by the test tool and included in the cycle-count.
|
|
These cycles are consumed by retries and inefficient API calls enqueuing and
|
|
dequeuing smaller bursts than specified by the cmdline parameter. This results
|
|
in a larger cycle-count measurement and should not be interpreted as an offload
|
|
cost measurement. Using "pmd-cyclecount" mode will give a better idea of
|
|
actual costs of hardware acceleration.
|
|
|
|
On hardware devices the throughput measurement is not necessarily the maximum
|
|
possible for the device, e.g. it may be necessary to use multiple cores to keep
|
|
the hardware accelerator fully loaded and so measure maximum throughput.
|
|
|
|
|
|
Linearization setting
|
|
---------------------
|
|
|
|
It is possible linearized input segmented packets just before crypto operation
|
|
for devices which doesn't support scatter-gather, and allows to measure
|
|
performance also for this use case.
|
|
|
|
To set on the linearization options add below definition to the
|
|
``cperf_ops.h`` file::
|
|
|
|
#define CPERF_LINEARIZATION_ENABLE
|
|
|
|
|
|
Running the Application
|
|
-----------------------
|
|
|
|
The tool application has a number of command line options:
|
|
|
|
.. code-block:: console
|
|
|
|
dpdk-test-crypto-perf [EAL Options] -- [Application Options]
|
|
|
|
EAL Options
|
|
~~~~~~~~~~~
|
|
|
|
The following are the EAL command-line options that can be used in conjunction
|
|
with the ``dpdk-test-crypto-perf`` application.
|
|
See the DPDK Getting Started Guides for more information on these options.
|
|
|
|
* ``-c <COREMASK>`` or ``-l <CORELIST>``
|
|
|
|
Set the hexadecimal bitmask of the cores to run on. The corelist is a
|
|
list cores to use.
|
|
|
|
* ``-a <PCI>``
|
|
|
|
Add a PCI device in allow list.
|
|
|
|
* ``--vdev <driver><id>``
|
|
|
|
Add a virtual device.
|
|
|
|
Application Options
|
|
~~~~~~~~~~~~~~~~~~~
|
|
|
|
The following are the application command-line options:
|
|
|
|
* ``--ptest type``
|
|
|
|
Set test type, where ``type`` is one of the following::
|
|
|
|
throughput
|
|
latency
|
|
verify
|
|
pmd-cyclecount
|
|
|
|
* ``--silent``
|
|
|
|
Disable options dump.
|
|
|
|
* ``--pool-sz <n>``
|
|
|
|
Set the number of mbufs to be allocated in the mbuf pool.
|
|
|
|
* ``--total-ops <n>``
|
|
|
|
Set the number of total operations performed.
|
|
|
|
* ``--burst-sz <n>``
|
|
|
|
Set the number of packets per burst.
|
|
|
|
This can be set as:
|
|
* Single value (i.e. ``--burst-sz 16``)
|
|
* Range of values, using the following structure ``min:inc:max``,
|
|
where ``min`` is minimum size, ``inc`` is the increment size and ``max``
|
|
is the maximum size (i.e. ``--burst-sz 16:2:32``)
|
|
* List of values, up to 32 values, separated in commas (i.e. ``--burst-sz 16,24,32``)
|
|
|
|
* ``--buffer-sz <n>``
|
|
|
|
Set the size of single packet (plaintext or ciphertext in it).
|
|
|
|
This can be set as:
|
|
* Single value (i.e. ``--buffer-sz 16``)
|
|
* Range of values, using the following structure ``min:inc:max``,
|
|
where ``min`` is minimum size, ``inc`` is the increment size and ``max``
|
|
is the maximum size (i.e. ``--buffer-sz 16:2:32``)
|
|
* List of values, up to 32 values, separated in commas (i.e. ``--buffer-sz 32,64,128``)
|
|
|
|
* ``--imix <n>``
|
|
|
|
Set the distribution of packet sizes.
|
|
|
|
A list of weights must be passed, containing the same number of items than buffer-sz,
|
|
so each item in this list will be the weight of the packet size on the same position
|
|
in the buffer-sz parameter (a list have to be passed in that parameter).
|
|
|
|
Example:
|
|
|
|
To test a distribution of 20% packets of 64 bytes, 40% packets of 100 bytes and 40% packets
|
|
of 256 bytes, the command line would be: ``--buffer-sz 64,100,256 --imix 20,40,40``.
|
|
Note that the weights do not have to be percentages, so using ``--imix 1,2,2`` would result
|
|
in the same distribution
|
|
|
|
* ``--segment-sz <n>``
|
|
|
|
Set the size of the segment to use, for Scatter Gather List testing.
|
|
By default, it is set to the size of the maximum buffer size, including the digest size,
|
|
so a single segment is created.
|
|
|
|
* ``--devtype <name>``
|
|
|
|
Set device type, where ``name`` is one of the following::
|
|
|
|
crypto_aesni_gcm
|
|
crypto_aesni_mb
|
|
crypto_armv8
|
|
crypto_cn9k
|
|
crypto_cn10k
|
|
crypto_dpaa_sec
|
|
crypto_dpaa2_sec
|
|
crypto_kasumi
|
|
crypto_mvsam
|
|
crypto_null
|
|
crypto_octeontx
|
|
crypto_openssl
|
|
crypto_qat
|
|
crypto_scheduler
|
|
crypto_snow3g
|
|
crypto_zuc
|
|
|
|
* ``--optype <name>``
|
|
|
|
Set operation type, where ``name`` is one of the following::
|
|
|
|
cipher-only
|
|
auth-only
|
|
cipher-then-auth
|
|
auth-then-cipher
|
|
aead
|
|
pdcp
|
|
docsis
|
|
modex
|
|
|
|
For GCM/CCM algorithms you should use aead flag.
|
|
|
|
* ``--sessionless``
|
|
|
|
Enable session-less crypto operations mode.
|
|
|
|
* ``--out-of-place``
|
|
|
|
Enable out-of-place crypto operations mode.
|
|
|
|
* ``--test-file <name>``
|
|
|
|
Set test vector file path. See the Test Vector File chapter.
|
|
|
|
* ``--test-name <name>``
|
|
|
|
Set specific test name section in the test vector file.
|
|
|
|
* ``--cipher-algo <name>``
|
|
|
|
Set cipher algorithm name, where ``name`` is one of the following::
|
|
|
|
3des-cbc
|
|
3des-ecb
|
|
3des-ctr
|
|
aes-cbc
|
|
aes-ctr
|
|
aes-ecb
|
|
aes-f8
|
|
aes-xts
|
|
arc4
|
|
null
|
|
kasumi-f8
|
|
snow3g-uea2
|
|
zuc-eea3
|
|
|
|
* ``--cipher-op <mode>``
|
|
|
|
Set cipher operation mode, where ``mode`` is one of the following::
|
|
|
|
encrypt
|
|
decrypt
|
|
|
|
* ``--cipher-key-sz <n>``
|
|
|
|
Set the size of cipher key.
|
|
|
|
* ``--cipher-iv-sz <n>``
|
|
|
|
Set the size of cipher iv.
|
|
|
|
* ``--auth-algo <name>``
|
|
|
|
Set authentication algorithm name, where ``name`` is one
|
|
of the following::
|
|
|
|
3des-cbc
|
|
aes-cbc-mac
|
|
aes-cmac
|
|
aes-gmac
|
|
aes-xcbc-mac
|
|
md5
|
|
md5-hmac
|
|
sha1
|
|
sha1-hmac
|
|
sha2-224
|
|
sha2-224-hmac
|
|
sha2-256
|
|
sha2-256-hmac
|
|
sha2-384
|
|
sha2-384-hmac
|
|
sha2-512
|
|
sha2-512-hmac
|
|
kasumi-f9
|
|
snow3g-uia2
|
|
zuc-eia3
|
|
|
|
* ``--auth-op <mode>``
|
|
|
|
Set authentication operation mode, where ``mode`` is one of
|
|
the following::
|
|
|
|
verify
|
|
generate
|
|
|
|
* ``--auth-key-sz <n>``
|
|
|
|
Set the size of authentication key.
|
|
|
|
* ``--auth-iv-sz <n>``
|
|
|
|
Set the size of auth iv.
|
|
|
|
* ``--aead-algo <name>``
|
|
|
|
Set AEAD algorithm name, where ``name`` is one
|
|
of the following::
|
|
|
|
aes-ccm
|
|
aes-gcm
|
|
|
|
* ``--aead-op <mode>``
|
|
|
|
Set AEAD operation mode, where ``mode`` is one of
|
|
the following::
|
|
|
|
encrypt
|
|
decrypt
|
|
|
|
* ``--aead-key-sz <n>``
|
|
|
|
Set the size of AEAD key.
|
|
|
|
* ``--aead-iv-sz <n>``
|
|
|
|
Set the size of AEAD iv.
|
|
|
|
* ``--aead-aad-sz <n>``
|
|
|
|
Set the size of AEAD aad.
|
|
|
|
* ``--digest-sz <n>``
|
|
|
|
Set the size of digest.
|
|
|
|
* ``--desc-nb <n>``
|
|
|
|
Set number of descriptors for each crypto device.
|
|
|
|
* ``--pmd-cyclecount-delay-ms <n>``
|
|
|
|
Add a delay (in milliseconds) between enqueue and dequeue in
|
|
pmd-cyclecount benchmarking mode (useful when benchmarking
|
|
hardware acceleration).
|
|
|
|
* ``--csv-friendly``
|
|
|
|
Enable test result output CSV friendly rather than human friendly.
|
|
|
|
* ``--pdcp-sn-sz <n>``
|
|
|
|
Set PDCP sequence number size(n) in bits. Valid values of n will
|
|
be 5/7/12/15/18.
|
|
|
|
* ``--pdcp-domain <control/user>``
|
|
|
|
Set PDCP domain to specify short_mac/control/user plane.
|
|
|
|
* ``--docsis-hdr-sz <n>``
|
|
|
|
Set DOCSIS header size(n) in bytes.
|
|
|
|
* ``--pdcp-ses-hfn-en``
|
|
|
|
Enable fixed session based HFN instead of per packet HFN.
|
|
|
|
Test Vector File
|
|
~~~~~~~~~~~~~~~~
|
|
|
|
The test vector file is a text file contain information about test vectors.
|
|
The file is made of the sections. The first section doesn't have header.
|
|
It contain global information used in each test variant vectors -
|
|
typically information about plaintext, ciphertext, cipher key, auth key,
|
|
initial vector. All other sections begin header.
|
|
The sections contain particular information typically digest.
|
|
|
|
**Format of the file:**
|
|
|
|
Each line beginning with sign '#' contain comment and it is ignored by parser::
|
|
|
|
# <comment>
|
|
|
|
Header line is just name in square bracket::
|
|
|
|
[<section name>]
|
|
|
|
Data line contain information token then sign '=' and
|
|
a string of bytes in C byte array format::
|
|
|
|
<token> = <C byte array>
|
|
|
|
**Tokens list:**
|
|
|
|
* ``plaintext``
|
|
|
|
Original plaintext to be encrypted.
|
|
|
|
* ``ciphertext``
|
|
|
|
Encrypted plaintext string.
|
|
|
|
* ``cipher_key``
|
|
|
|
Key used in cipher operation.
|
|
|
|
* ``auth_key``
|
|
|
|
Key used in auth operation.
|
|
|
|
* ``cipher_iv``
|
|
|
|
Cipher Initial Vector.
|
|
|
|
* ``auth_iv``
|
|
|
|
Auth Initial Vector.
|
|
|
|
* ``aad``
|
|
|
|
Additional data.
|
|
|
|
* ``digest``
|
|
|
|
Digest string.
|
|
|
|
Examples
|
|
--------
|
|
|
|
Call application for performance throughput test of single Aesni MB PMD
|
|
for cipher encryption aes-cbc and auth generation sha1-hmac,
|
|
one million operations, burst size 32, packet size 64::
|
|
|
|
dpdk-test-crypto-perf -l 6-7 --vdev crypto_aesni_mb -a 0000:00:00.0 --
|
|
--ptest throughput --devtype crypto_aesni_mb --optype cipher-then-auth
|
|
--cipher-algo aes-cbc --cipher-op encrypt --cipher-key-sz 16 --auth-algo
|
|
sha1-hmac --auth-op generate --auth-key-sz 64 --digest-sz 12
|
|
--total-ops 10000000 --burst-sz 32 --buffer-sz 64
|
|
|
|
Call application for performance latency test of two Aesni MB PMD executed
|
|
on two cores for cipher encryption aes-cbc, ten operations in silent mode::
|
|
|
|
dpdk-test-crypto-perf -l 4-7 --vdev crypto_aesni_mb1
|
|
--vdev crypto_aesni_mb2 -a 0000:00:00.0 -- --devtype crypto_aesni_mb
|
|
--cipher-algo aes-cbc --cipher-key-sz 16 --cipher-iv-sz 16
|
|
--cipher-op encrypt --optype cipher-only --silent
|
|
--ptest latency --total-ops 10
|
|
|
|
Call application for verification test of single open ssl PMD
|
|
for cipher encryption aes-gcm and auth generation aes-gcm,ten operations
|
|
in silent mode, test vector provide in file "test_aes_gcm.data"
|
|
with packet verification::
|
|
|
|
dpdk-test-crypto-perf -l 4-7 --vdev crypto_openssl -a 0000:00:00.0 --
|
|
--devtype crypto_openssl --aead-algo aes-gcm --aead-key-sz 16
|
|
--aead-iv-sz 16 --aead-op encrypt --aead-aad-sz 16 --digest-sz 16
|
|
--optype aead --silent --ptest verify --total-ops 10
|
|
--test-file test_aes_gcm.data
|
|
|
|
Test vector file for cipher algorithm aes cbc 256 with authorization sha::
|
|
|
|
# Global Section
|
|
plaintext =
|
|
0xff, 0xca, 0xfb, 0xf1, 0x38, 0x20, 0x2f, 0x7b, 0x24, 0x98, 0x26, 0x7d, 0x1d, 0x9f, 0xb3, 0x93,
|
|
0xd9, 0xef, 0xbd, 0xad, 0x4e, 0x40, 0xbd, 0x60, 0xe9, 0x48, 0x59, 0x90, 0x67, 0xd7, 0x2b, 0x7b,
|
|
0x8a, 0xe0, 0x4d, 0xb0, 0x70, 0x38, 0xcc, 0x48, 0x61, 0x7d, 0xee, 0xd6, 0x35, 0x49, 0xae, 0xb4,
|
|
0xaf, 0x6b, 0xdd, 0xe6, 0x21, 0xc0, 0x60, 0xce, 0x0a, 0xf4, 0x1c, 0x2e, 0x1c, 0x8d, 0xe8, 0x7b
|
|
ciphertext =
|
|
0x77, 0xF9, 0xF7, 0x7A, 0xA3, 0xCB, 0x68, 0x1A, 0x11, 0x70, 0xD8, 0x7A, 0xB6, 0xE2, 0x37, 0x7E,
|
|
0xD1, 0x57, 0x1C, 0x8E, 0x85, 0xD8, 0x08, 0xBF, 0x57, 0x1F, 0x21, 0x6C, 0xAD, 0xAD, 0x47, 0x1E,
|
|
0x0D, 0x6B, 0x79, 0x39, 0x15, 0x4E, 0x5B, 0x59, 0x2D, 0x76, 0x87, 0xA6, 0xD6, 0x47, 0x8F, 0x82,
|
|
0xB8, 0x51, 0x91, 0x32, 0x60, 0xCB, 0x97, 0xDE, 0xBE, 0xF0, 0xAD, 0xFC, 0x23, 0x2E, 0x22, 0x02
|
|
cipher_key =
|
|
0xE4, 0x23, 0x33, 0x8A, 0x35, 0x64, 0x61, 0xE2, 0x49, 0x03, 0xDD, 0xC6, 0xB8, 0xCA, 0x55, 0x7A,
|
|
0xd0, 0xe7, 0x4b, 0xfb, 0x5d, 0xe5, 0x0c, 0xe7, 0x6f, 0x21, 0xb5, 0x52, 0x2a, 0xbb, 0xc7, 0xf7
|
|
auth_key =
|
|
0xaf, 0x96, 0x42, 0xf1, 0x8c, 0x50, 0xdc, 0x67, 0x1a, 0x43, 0x47, 0x62, 0xc7, 0x04, 0xab, 0x05,
|
|
0xf5, 0x0c, 0xe7, 0xa2, 0xa6, 0x23, 0xd5, 0x3d, 0x95, 0xd8, 0xcd, 0x86, 0x79, 0xf5, 0x01, 0x47,
|
|
0x4f, 0xf9, 0x1d, 0x9d, 0x36, 0xf7, 0x68, 0x1a, 0x64, 0x44, 0x58, 0x5d, 0xe5, 0x81, 0x15, 0x2a,
|
|
0x41, 0xe4, 0x0e, 0xaa, 0x1f, 0x04, 0x21, 0xff, 0x2c, 0xf3, 0x73, 0x2b, 0x48, 0x1e, 0xd2, 0xf7
|
|
cipher_iv =
|
|
0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B, 0x0C, 0x0D, 0x0E, 0x0F
|
|
# Section sha 1 hmac buff 32
|
|
[sha1_hmac_buff_32]
|
|
digest =
|
|
0x36, 0xCA, 0x49, 0x6A, 0xE3, 0x54, 0xD8, 0x4F, 0x0B, 0x76, 0xD8, 0xAA, 0x78, 0xEB, 0x9D, 0x65,
|
|
0x2C, 0xCA, 0x1F, 0x97
|
|
# Section sha 256 hmac buff 32
|
|
[sha256_hmac_buff_32]
|
|
digest =
|
|
0x1C, 0xB2, 0x3D, 0xD1, 0xF9, 0xC7, 0x6C, 0x49, 0x2E, 0xDA, 0x94, 0x8B, 0xF1, 0xCF, 0x96, 0x43,
|
|
0x67, 0x50, 0x39, 0x76, 0xB5, 0xA1, 0xCE, 0xA1, 0xD7, 0x77, 0x10, 0x07, 0x43, 0x37, 0x05, 0xB4
|
|
|
|
|
|
Graph Crypto Perf Results
|
|
-------------------------
|
|
|
|
The ``dpdk-graph-crypto-perf.py`` tool is a simple script to automate
|
|
running crypto performance tests, and graphing the results.
|
|
It can be found in the ``app/test-crypto-perf/`` directory.
|
|
The output graphs include various grouped barcharts for throughput
|
|
tests, and histogram and boxplot graphs for latency tests.
|
|
These are output to PDF files, with one PDF per test suite graph type.
|
|
|
|
|
|
Dependencies
|
|
~~~~~~~~~~~~
|
|
|
|
The following python modules must be installed to run the script:
|
|
|
|
.. code-block:: console
|
|
|
|
pip3 install img2pdf plotly pandas psutil kaleido
|
|
|
|
|
|
Test Configuration
|
|
~~~~~~~~~~~~~~~~~~
|
|
|
|
The test cases run by the script are defined by a JSON config file.
|
|
Some config files can be found in ``app/test-crypto-perf/configs/``,
|
|
or the user may create a new one following the same format as the config files provided.
|
|
|
|
An example of this format is shown below for one test suite in the ``crypto-perf-aesni-mb.json`` file.
|
|
This shows the required default config for the test suite, and one test case.
|
|
The test case has additional app config that will be combined with
|
|
the default config when running the test case.
|
|
|
|
.. code-block:: c
|
|
|
|
"throughput": {
|
|
"default": {
|
|
"eal": {
|
|
"l": "1,2",
|
|
"vdev": "crypto_aesni_mb"
|
|
},
|
|
"app": {
|
|
"csv-friendly": true,
|
|
"buffer-sz": "64,128,256,512,768,1024,1408,2048",
|
|
"burst-sz": "1,4,8,16,32",
|
|
"ptest": "throughput",
|
|
"devtype": "crypto_aesni_mb"
|
|
}
|
|
},
|
|
"AES-CBC-128 SHA1-HMAC auth-then-cipher decrypt": {
|
|
"cipher-algo": "aes-cbc",
|
|
"cipher-key-sz": "16",
|
|
"auth-algo": "sha1-hmac",
|
|
"optype": "auth-then-cipher",
|
|
"cipher-op": "decrypt"
|
|
}
|
|
}
|
|
|
|
.. note::
|
|
The specific test cases only allow modification of app parameters,
|
|
and not EAL parameters.
|
|
The default case is required for each test suite in the config file,
|
|
to specify EAL parameters.
|
|
|
|
Currently, crypto_qat, crypto_aesni_mb, and crypto_aesni_gcm devices for
|
|
both throughput and latency ptests are supported.
|
|
|
|
|
|
Usage
|
|
~~~~~
|
|
|
|
.. code-block:: console
|
|
|
|
./dpdk-graph-crypto-perf <config_file>
|
|
|
|
The ``config_file`` positional argument is required to run the script.
|
|
This points to a valid JSON config file containing test suites.
|
|
|
|
.. code-block:: console
|
|
|
|
./dpdk-graph-crypto-perf configs/crypto-perf-aesni-mb.json
|
|
|
|
The following are the application optional command-line options:
|
|
|
|
* ``-h, --help``
|
|
|
|
Display usage information and quit.
|
|
|
|
* ``-f <file_path>, --file-path <file_path>``
|
|
|
|
Provide path to ``dpdk-test-crypto-perf`` application.
|
|
The script uses the installed app by default.
|
|
|
|
.. code-block:: console
|
|
|
|
./dpdk-graph-crypto-perf <config_file> \
|
|
-f <build_dir>/app/dpdk-test-crypto-perf
|
|
|
|
* ``-t <test_suite_list>, --test-suites <test_suite_list>``
|
|
|
|
Specify test suites to run. All test suites are run by default.
|
|
|
|
To run crypto-perf-qat latency test suite only:
|
|
|
|
.. code-block:: console
|
|
|
|
./dpdk-graph-crypto-perf configs/crypto-perf-qat -t latency
|
|
|
|
To run both crypto-perf-aesni-mb throughput and latency test suites
|
|
|
|
.. code-block:: console
|
|
|
|
./dpdk-graph-crypto-perf configs/crypto-perf-aesni-mb -t throughput latency
|
|
|
|
* ``-o <output_path>, --output-path <output_path>``
|
|
|
|
Specify directory to use for output files.
|
|
The default is to use the script's directory.
|
|
|
|
.. code-block:: console
|
|
|
|
./dpdk-graph-crypto-perf <config_file> -o <output_dir>
|
|
|
|
* ``-v, --verbose``
|
|
|
|
Enable verbose output. This displays ``dpdk-test-crypto-perf`` app output in real-time.
|
|
|
|
.. code-block:: console
|
|
|
|
./dpdk-graph-crypto-perf <config_file> -v
|
|
|
|
.. warning::
|
|
Latency performance tests have a large amount of output.
|
|
It is not recommended to use the verbose option for latency tests.
|