d/numam-dpdk
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
35b2d13fd6
numam-dpdk/doc/guides/nics/mlx5.rst
Ori Kam 909be50a34 doc: update Mellanox guides and release notes 
This patch adds some missing features to Mellanox drivers release notes.
It also updates the mlx5/mlx4 documentations.

Fixes: d85b204b5d ("doc: update release notes for Mellanox drivers")

Signed-off-by: Ori Kam <orika@mellanox.com>
Acked-by: Shahaf Shuler <shahafs@mellanox.com>
2019-05-13 21:09:04 +02:00

1084 lines
40 KiB
ReStructuredText
Raw Blame History

.. SPDX-License-Identifier: BSD-3-Clause
Copyright 2015 6WIND S.A.
Copyright 2015 Mellanox Technologies, Ltd
MLX5 poll mode driver
=====================
The MLX5 poll mode driver library (**librte_pmd_mlx5**) provides support
for **Mellanox ConnectX-4**, **Mellanox ConnectX-4 Lx** , **Mellanox
ConnectX-5**, **Mellanox ConnectX-6** and **Mellanox BlueField** families
of 10/25/40/50/100/200 Gb/s adapters as well as their virtual functions (VF)
in SR-IOV context.
Information and documentation about these adapters can be found on the
`Mellanox website <http://www.mellanox.com>`__. Help is also provided by the
`Mellanox community <http://community.mellanox.com/welcome>`__.
There is also a `section dedicated to this poll mode driver
<http://www.mellanox.com/page/products_dyn?product_family=209&mtag=pmd_for_dpdk>`__.
.. note::
Due to external dependencies, this driver is disabled by default. It must
be enabled manually by setting ``CONFIG_RTE_LIBRTE_MLX5_PMD=y`` and
recompiling DPDK.
Implementation details
----------------------
Besides its dependency on libibverbs (that implies libmlx5 and associated
kernel support), librte_pmd_mlx5 relies heavily on system calls for control
operations such as querying/updating the MTU and flow control parameters.
For security reasons and robustness, this driver only deals with virtual
memory addresses. The way resources allocations are handled by the kernel
combined with hardware specifications that allow it to handle virtual memory
addresses directly ensure that DPDK applications cannot access random
physical memory (or memory that does not belong to the current process).
This capability allows the PMD to coexist with kernel network interfaces
which remain functional, although they stop receiving unicast packets as
long as they share the same MAC address.
This means legacy linux control tools (for example: ethtool, ifconfig and
more) can operate on the same network interfaces that owned by the DPDK
application.
Enabling librte_pmd_mlx5 causes DPDK applications to be linked against
libibverbs.
Features
--------
- Multi arch support: x86_64, POWER8, ARMv8, i686.
- Multiple TX and RX queues.
- Support for scattered TX and RX frames.
- IPv4, IPv6, TCPv4, TCPv6, UDPv4 and UDPv6 RSS on any number of queues.
- Several RSS hash keys, one for each flow type.
- Default RSS operation with no hash key specification.
- Configurable RETA table.
- Support for multiple MAC addresses.
- VLAN filtering.
- RX VLAN stripping.
- TX VLAN insertion.
- RX CRC stripping configuration.
- Promiscuous mode on PF and VF.
- Multicast promiscuous mode on PF and VF.
- Hardware checksum offloads.
- Flow director (RTE_FDIR_MODE_PERFECT, RTE_FDIR_MODE_PERFECT_MAC_VLAN and
RTE_ETH_FDIR_REJECT).
- Flow API, including :ref:`flow_isolated_mode`.
- Multiple process.
- KVM and VMware ESX SR-IOV modes are supported.
- RSS hash result is supported.
- Hardware TSO for generic IP or UDP tunnel, including VXLAN and GRE.
- Hardware checksum Tx offload for generic IP or UDP tunnel, including VXLAN and GRE.
- RX interrupts.
- Statistics query including Basic, Extended and per queue.
- Rx HW timestamp.
- Tunnel types: VXLAN, L3 VXLAN, VXLAN-GPE, GRE, MPLSoGRE, MPLSoUDP.
- Tunnel HW offloads: packet type, inner/outer RSS, IP and UDP checksum verification.
- NIC HW offloads: encapsulation (vxlan, gre, mplsoudp, mplsogre), NAT, routing, TTL
increment/decrement, count, drop, mark. For details please see :ref:`Supported hardware offloads using rte_flow API`.
- Flow insertion rate of more then million flows per second, when using Direct Rules.
- Support for multiple rte_flow groups.
Limitations
-----------
- For secondary process:
- Forked secondary process not supported.
- External memory unregistered in EAL memseg list cannot be used for DMA
unless such memory has been registered by ``mlx5_mr_update_ext_mp()`` in
primary process and remapped to the same virtual address in secondary
process. If the external memory is registered by primary process but has
different virtual address in secondary process, unexpected error may happen.
- Flow pattern without any specific vlan will match for vlan packets as well:
When VLAN spec is not specified in the pattern, the matching rule will be created with VLAN as a wild card.
Meaning, the flow rule::
flow create 0 ingress pattern eth / vlan vid is 3 / ipv4 / end ...
Will only match vlan packets with vid=3. and the flow rules::
flow create 0 ingress pattern eth / ipv4 / end ...
Or::
flow create 0 ingress pattern eth / vlan / ipv4 / end ...
Will match any ipv4 packet (VLAN included).
- A multi segment packet must have less than 6 segments in case the Tx burst function
is set to multi-packet send or Enhanced multi-packet send. Otherwise it must have
less than 50 segments.
- Flows with a VXLAN Network Identifier equal (or ends to be equal)
to 0 are not supported.
- VXLAN TSO and checksum offloads are not supported on VM.
- L3 VXLAN and VXLAN-GPE tunnels cannot be supported together with MPLSoGRE and MPLSoUDP.
- VF: flow rules created on VF devices can only match traffic targeted at the
configured MAC addresses (see ``rte_eth_dev_mac_addr_add()``).
.. note::
MAC addresses not already present in the bridge table of the associated
kernel network device will be added and cleaned up by the PMD when closing
the device. In case of ungraceful program termination, some entries may
remain present and should be removed manually by other means.
- When Multi-Packet Rx queue is configured (``mprq_en``), a Rx packet can be
externally attached to a user-provided mbuf with having EXT_ATTACHED_MBUF in
ol_flags. As the mempool for the external buffer is managed by PMD, all the
Rx mbufs must be freed before the device is closed. Otherwise, the mempool of
the external buffers will be freed by PMD and the application which still
holds the external buffers may be corrupted.
- If Multi-Packet Rx queue is configured (``mprq_en``) and Rx CQE compression is
enabled (``rxq_cqe_comp_en``) at the same time, RSS hash result is not fully
supported. Some Rx packets may not have PKT_RX_RSS_HASH.
- IPv6 Multicast messages are not supported on VM, while promiscuous mode
and allmulticast mode are both set to off.
To receive IPv6 Multicast messages on VM, explicitly set the relevant
MAC address using rte_eth_dev_mac_addr_add() API.
- E-Switch decapsulation Flow:
- can be applied to PF port only.
- must specify VF port action (packet redirection from PF to VF).
- optionally may specify tunnel inner source and destination MAC addresses.
- E-Switch encapsulation Flow:
- can be applied to VF ports only.
- must specify PF port action (packet redirection from VF to PF).
Statistics
----------
MLX5 supports various of methods to report statistics:
Port statistics can be queried using ``rte_eth_stats_get()``. The received and sent statistics are through SW only and counts the number of packets received or sent successfully by the PMD. The imissed counter is the amount of packets that could not be delivered to SW because a queue was full. Packets not received due to congestion in the bus or on the NIC can be queried via the rx_discards_phy xstats counter.
Extended statistics can be queried using ``rte_eth_xstats_get()``. The extended statistics expose a wider set of counters counted by the device. The extended port statistics counts the number of packets received or sent successfully by the port. As Mellanox NICs are using the :ref:`Bifurcated Linux Driver <linux_gsg_linux_drivers>` those counters counts also packet received or sent by the Linux kernel. The counters with ``_phy`` suffix counts the total events on the physical port, therefore not valid for VF.
Finally per-flow statistics can by queried using ``rte_flow_query`` when attaching a count action for specific flow. The flow counter counts the number of packets received successfully by the port and match the specific flow.
Configuration
-------------
Compilation options
~~~~~~~~~~~~~~~~~~~
These options can be modified in the ``.config`` file.
- ``CONFIG_RTE_LIBRTE_MLX5_PMD`` (default **n**)
Toggle compilation of librte_pmd_mlx5 itself.
- ``CONFIG_RTE_IBVERBS_LINK_DLOPEN`` (default **n**)
Build PMD with additional code to make it loadable without hard
dependencies on **libibverbs** nor **libmlx5**, which may not be installed
on the target system.
In this mode, their presence is still required for it to run properly,
however their absence won't prevent a DPDK application from starting (with
``CONFIG_RTE_BUILD_SHARED_LIB`` disabled) and they won't show up as
missing with ``ldd(1)``.
It works by moving these dependencies to a purpose-built rdma-core "glue"
plug-in which must either be installed in a directory whose name is based
on ``CONFIG_RTE_EAL_PMD_PATH`` suffixed with ``-glue`` if set, or in a
standard location for the dynamic linker (e.g. ``/lib``) if left to the
default empty string (``""``).
This option has no performance impact.
- ``CONFIG_RTE_IBVERBS_LINK_STATIC`` (default **n**)
Embed static flavor of the dependencies **libibverbs** and **libmlx5**
in the PMD shared library or the executable static binary.
- ``CONFIG_RTE_LIBRTE_MLX5_DEBUG`` (default **n**)
Toggle debugging code and stricter compilation flags. Enabling this option
adds additional run-time checks and debugging messages at the cost of
lower performance.
.. note::
For BlueField, target should be set to ``arm64-bluefield-linux-gcc``. This
will enable ``CONFIG_RTE_LIBRTE_MLX5_PMD`` and set ``RTE_CACHE_LINE_SIZE`` to
64. Default armv8a configuration of make build and meson build set it to 128
then brings performance degradation.
Environment variables
~~~~~~~~~~~~~~~~~~~~~
- ``MLX5_GLUE_PATH``
A list of directories in which to search for the rdma-core "glue" plug-in,
separated by colons or semi-colons.
Only matters when compiled with ``CONFIG_RTE_IBVERBS_LINK_DLOPEN``
enabled and most useful when ``CONFIG_RTE_EAL_PMD_PATH`` is also set,
since ``LD_LIBRARY_PATH`` has no effect in this case.
- ``MLX5_SHUT_UP_BF``
Configures HW Tx doorbell register as IO-mapped.
By default, the HW Tx doorbell is configured as a write-combining register.
The register would be flushed to HW usually when the write-combining buffer
becomes full, but it depends on CPU design.
Except for vectorized Tx burst routines, a write memory barrier is enforced
after updating the register so that the update can be immediately visible to
HW.
When vectorized Tx burst is called, the barrier is set only if the burst size
is not aligned to MLX5_VPMD_TX_MAX_BURST. However, setting this environmental
variable will bring better latency even though the maximum throughput can
slightly decline.
Run-time configuration
~~~~~~~~~~~~~~~~~~~~~~
- librte_pmd_mlx5 brings kernel network interfaces up during initialization
because it is affected by their state. Forcing them down prevents packets
reception.
- **ethtool** operations on related kernel interfaces also affect the PMD.
- ``rxq_cqe_comp_en`` parameter [int]
A nonzero value enables the compression of CQE on RX side. This feature
allows to save PCI bandwidth and improve performance. Enabled by default.
Supported on:
- x86_64 with ConnectX-4, ConnectX-4 LX, ConnectX-5, ConnectX-6 and BlueField.
- POWER9 and ARMv8 with ConnectX-4 LX, ConnectX-5, ConnectX-6 and BlueField.
- ``rxq_cqe_pad_en`` parameter [int]
A nonzero value enables 128B padding of CQE on RX side. The size of CQE
is aligned with the size of a cacheline of the core. If cacheline size is
128B, the CQE size is configured to be 128B even though the device writes
only 64B data on the cacheline. This is to avoid unnecessary cache
invalidation by device's two consecutive writes on to one cacheline.
However in some architecture, it is more beneficial to update entire
cacheline with padding the rest 64B rather than striding because
read-modify-write could drop performance a lot. On the other hand,
writing extra data will consume more PCIe bandwidth and could also drop
the maximum throughput. It is recommended to empirically set this
parameter. Disabled by default.
Supported on:
- CPU having 128B cacheline with ConnectX-5 and BlueField.
- ``rxq_pkt_pad_en`` parameter [int]
A nonzero value enables padding Rx packet to the size of cacheline on PCI
transaction. This feature would waste PCI bandwidth but could improve
performance by avoiding partial cacheline write which may cause costly
read-modify-copy in memory transaction on some architectures. Disabled by
default.
Supported on:
- x86_64 with ConnectX-4, ConnectX-4 LX, ConnectX-5, ConnectX-6 and BlueField.
- POWER8 and ARMv8 with ConnectX-4 LX, ConnectX-5, ConnectX-6 and BlueField.
- ``mprq_en`` parameter [int]
A nonzero value enables configuring Multi-Packet Rx queues. Rx queue is
configured as Multi-Packet RQ if the total number of Rx queues is
``rxqs_min_mprq`` or more and Rx scatter isn't configured. Disabled by
default.
Multi-Packet Rx Queue (MPRQ a.k.a Striding RQ) can further save PCIe bandwidth
by posting a single large buffer for multiple packets. Instead of posting a
buffers per a packet, one large buffer is posted in order to receive multiple
packets on the buffer. A MPRQ buffer consists of multiple fixed-size strides
and each stride receives one packet. MPRQ can improve throughput for
small-packet traffic.
When MPRQ is enabled, max_rx_pkt_len can be larger than the size of
user-provided mbuf even if DEV_RX_OFFLOAD_SCATTER isn't enabled. PMD will
configure large stride size enough to accommodate max_rx_pkt_len as long as
device allows. Note that this can waste system memory compared to enabling Rx
scatter and multi-segment packet.
- ``mprq_log_stride_num`` parameter [int]
Log 2 of the number of strides for Multi-Packet Rx queue. Configuring more
strides can reduce PCIe traffic further. If configured value is not in the
range of device capability, the default value will be set with a warning
message. The default value is 4 which is 16 strides per a buffer, valid only
if ``mprq_en`` is set.
The size of Rx queue should be bigger than the number of strides.
- ``mprq_max_memcpy_len`` parameter [int]
The maximum length of packet to memcpy in case of Multi-Packet Rx queue. Rx
packet is mem-copied to a user-provided mbuf if the size of Rx packet is less
than or equal to this parameter. Otherwise, PMD will attach the Rx packet to
the mbuf by external buffer attachment - ``rte_pktmbuf_attach_extbuf()``.
A mempool for external buffers will be allocated and managed by PMD. If Rx
packet is externally attached, ol_flags field of the mbuf will have
EXT_ATTACHED_MBUF and this flag must be preserved. ``RTE_MBUF_HAS_EXTBUF()``
checks the flag. The default value is 128, valid only if ``mprq_en`` is set.
- ``rxqs_min_mprq`` parameter [int]
Configure Rx queues as Multi-Packet RQ if the total number of Rx queues is
greater or equal to this value. The default value is 12, valid only if
``mprq_en`` is set.
- ``txq_inline`` parameter [int]
Amount of data to be inlined during TX operations. Improves latency.
Can improve PPS performance when PCI back pressure is detected and may be
useful for scenarios involving heavy traffic on many queues.
Because additional software logic is necessary to handle this mode, this
option should be used with care, as it can lower performance when back
pressure is not expected.
- ``txqs_min_inline`` parameter [int]
Enable inline send only when the number of TX queues is greater or equal
to this value.
This option should be used in combination with ``txq_inline`` above.
On ConnectX-4, ConnectX-4 LX, ConnectX-5, ConnectX-6 and BlueField without
Enhanced MPW:
- Disabled by default.
- In case ``txq_inline`` is set recommendation is 4.
On ConnectX-5, ConnectX-6 and BlueField with Enhanced MPW:
- Set to 8 by default.
- ``txqs_max_vec`` parameter [int]
Enable vectorized Tx only when the number of TX queues is less than or
equal to this value. Effective only when ``tx_vec_en`` is enabled.
On ConnectX-5:
- Set to 8 by default on ARMv8.
- Set to 4 by default otherwise.
On BlueField
- Set to 16 by default.
- ``txq_mpw_en`` parameter [int]
A nonzero value enables multi-packet send (MPS) for ConnectX-4 Lx and
enhanced multi-packet send (Enhanced MPS) for ConnectX-5, ConnectX-6 and BlueField.
MPS allows the TX burst function to pack up multiple packets in a
single descriptor session in order to save PCI bandwidth and improve
performance at the cost of a slightly higher CPU usage. When
``txq_inline`` is set along with ``txq_mpw_en``, TX burst function tries
to copy entire packet data on to TX descriptor instead of including
pointer of packet only if there is enough room remained in the
descriptor. ``txq_inline`` sets per-descriptor space for either pointers
or inlined packets. In addition, Enhanced MPS supports hybrid mode -
mixing inlined packets and pointers in the same descriptor.
This option cannot be used with certain offloads such as ``DEV_TX_OFFLOAD_TCP_TSO,
DEV_TX_OFFLOAD_VXLAN_TNL_TSO, DEV_TX_OFFLOAD_GRE_TNL_TSO, DEV_TX_OFFLOAD_VLAN_INSERT``.
When those offloads are requested the MPS send function will not be used.
It is currently only supported on the ConnectX-4 Lx, ConnectX-5, ConnectX-6 and BlueField
families of adapters.
On ConnectX-4 Lx the MPW is considered un-secure hence disabled by default.
Users which enable the MPW should be aware that application which provides incorrect
mbuf descriptors in the Tx burst can lead to serious errors in the host including, on some cases,
NIC to get stuck.
On ConnectX-5, ConnectX-6 and BlueField the MPW is secure and enabled by default.
- ``txq_mpw_hdr_dseg_en`` parameter [int]
A nonzero value enables including two pointers in the first block of TX
descriptor. This can be used to lessen CPU load for memory copy.
Effective only when Enhanced MPS is supported. Disabled by default.
- ``txq_max_inline_len`` parameter [int]
Maximum size of packet to be inlined. This limits the size of packet to
be inlined. If the size of a packet is larger than configured value, the
packet isn't inlined even though there's enough space remained in the
descriptor. Instead, the packet is included with pointer.
Effective only when Enhanced MPS is supported. The default value is 256.
- ``tx_vec_en`` parameter [int]
A nonzero value enables Tx vector on ConnectX-5, ConnectX-6 and BlueField NICs if the number of
global Tx queues on the port is less than ``txqs_max_vec``.
This option cannot be used with certain offloads such as ``DEV_TX_OFFLOAD_TCP_TSO,
DEV_TX_OFFLOAD_VXLAN_TNL_TSO, DEV_TX_OFFLOAD_GRE_TNL_TSO, DEV_TX_OFFLOAD_VLAN_INSERT``.
When those offloads are requested the MPS send function will not be used.
Enabled by default on ConnectX-5, ConnectX-6 and BlueField.
- ``rx_vec_en`` parameter [int]
A nonzero value enables Rx vector if the port is not configured in
multi-segment otherwise this parameter is ignored.
Enabled by default.
- ``vf_nl_en`` parameter [int]
A nonzero value enables Netlink requests from the VF to add/remove MAC
addresses or/and enable/disable promiscuous/all multicast on the Netdevice.
Otherwise the relevant configuration must be run with Linux iproute2 tools.
This is a prerequisite to receive this kind of traffic.
Enabled by default, valid only on VF devices ignored otherwise.
- ``l3_vxlan_en`` parameter [int]
A nonzero value allows L3 VXLAN and VXLAN-GPE flow creation. To enable
L3 VXLAN or VXLAN-GPE, users has to configure firmware and enable this
parameter. This is a prerequisite to receive this kind of traffic.
Disabled by default.
- ``dv_flow_en`` parameter [int]
A nonzero value enables the DV flow steering assuming it is supported
by the driver.
Disabled by default.
- ``dv_esw_en`` parameter [int]
A nonzero value enables E-Switch using Direct Rules.
Enabled by default if supported.
- ``mr_ext_memseg_en`` parameter [int]
A nonzero value enables extending memseg when registering DMA memory. If
enabled, the number of entries in MR (Memory Region) lookup table on datapath
is minimized and it benefits performance. On the other hand, it worsens memory
utilization because registered memory is pinned by kernel driver. Even if a
page in the extended chunk is freed, that doesn't become reusable until the
entire memory is freed.
Enabled by default.
- ``representor`` parameter [list]
This parameter can be used to instantiate DPDK Ethernet devices from
existing port (or VF) representors configured on the device.
It is a standard parameter whose format is described in
:ref:`ethernet_device_standard_device_arguments`.
For instance, to probe port representors 0 through 2::
representor=[0-2]
Firmware configuration
~~~~~~~~~~~~~~~~~~~~~~
- L3 VXLAN and VXLAN-GPE destination UDP port
.. code-block:: console
mlxconfig -d <mst device> set IP_OVER_VXLAN_EN=1
mlxconfig -d <mst device> set IP_OVER_VXLAN_PORT=<udp dport>
Verify configurations are set:
.. code-block:: console
mlxconfig -d <mst device> query | grep IP_OVER_VXLAN
IP_OVER_VXLAN_EN True(1)
IP_OVER_VXLAN_PORT <udp dport>
Prerequisites
-------------
This driver relies on external libraries and kernel drivers for resources
allocations and initialization. The following dependencies are not part of
DPDK and must be installed separately:
- **libibverbs**
User space Verbs framework used by librte_pmd_mlx5. This library provides
a generic interface between the kernel and low-level user space drivers
such as libmlx5.
It allows slow and privileged operations (context initialization, hardware
resources allocations) to be managed by the kernel and fast operations to
never leave user space.
- **libmlx5**
Low-level user space driver library for Mellanox
ConnectX-4/ConnectX-5/ConnectX-6/BlueField devices, it is automatically loaded
by libibverbs.
This library basically implements send/receive calls to the hardware
queues.
- **libmnl**
Minimalistic Netlink library mainly relied on to manage E-Switch flow
rules (i.e. those with the "transfer" attribute and typically involving
port representors).
- **Kernel modules**
They provide the kernel-side Verbs API and low level device drivers that
manage actual hardware initialization and resources sharing with user
space processes.
Unlike most other PMDs, these modules must remain loaded and bound to
their devices:
- mlx5_core: hardware driver managing Mellanox
ConnectX-4/ConnectX-5/ConnectX-6/BlueField devices and related Ethernet kernel
network devices.
- mlx5_ib: InifiniBand device driver.
- ib_uverbs: user space driver for Verbs (entry point for libibverbs).
- **Firmware update**
Mellanox OFED/EN releases include firmware updates for
ConnectX-4/ConnectX-5/ConnectX-6/BlueField adapters.
Because each release provides new features, these updates must be applied to
match the kernel modules and libraries they come with.
.. note::
Both libraries are BSD and GPL licensed. Linux kernel modules are GPL
licensed.
Installation
~~~~~~~~~~~~
Either RDMA Core library with a recent enough Linux kernel release
(recommended) or Mellanox OFED/EN, which provides compatibility with older
releases.
RDMA Core with Linux Kernel
^^^^^^^^^^^^^^^^^^^^^^^^^^^
- Minimal kernel version : v4.14 or the most recent 4.14-rc (see `Linux installation documentation`_)
- Minimal rdma-core version: v15+ commit 0c5f5765213a ("Merge pull request #227 from yishaih/tm")
(see `RDMA Core installation documentation`_)
- When building for i686 use:
- rdma-core version 18.0 or above built with 32bit support.
- Kernel version 4.14.41 or above.
- Starting with rdma-core v21, static libraries can be built::
cd build
CFLAGS=-fPIC cmake -DIN_PLACE=1 -DENABLE_STATIC=1 -GNinja ..
ninja
.. _`Linux installation documentation`: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git/plain/Documentation/admin-guide/README.rst
.. _`RDMA Core installation documentation`: https://raw.githubusercontent.com/linux-rdma/rdma-core/master/README.md
If rdma-core libraries are built but not installed, DPDK makefile can link them,
thanks to these environment variables:
- ``EXTRA_CFLAGS=-I/path/to/rdma-core/build/include``
- ``EXTRA_LDFLAGS=-L/path/to/rdma-core/build/lib``
- ``PKG_CONFIG_PATH=/path/to/rdma-core/build/lib/pkgconfig``
Mellanox OFED/EN
^^^^^^^^^^^^^^^^
- Mellanox OFED version: ** 4.5, 4.6** /
Mellanox EN version: **4.5, 4.6**
- firmware version:
- ConnectX-4: **12.21.1000** and above.
- ConnectX-4 Lx: **14.21.1000** and above.
- ConnectX-5: **16.21.1000** and above.
- ConnectX-5 Ex: **16.21.1000** and above.
- ConnectX-6: **20.99.5374** and above.
- BlueField: **18.25.1010** and above.
While these libraries and kernel modules are available on OpenFabrics
Alliance's `website <https://www.openfabrics.org/>`__ and provided by package
managers on most distributions, this PMD requires Ethernet extensions that
may not be supported at the moment (this is a work in progress).
`Mellanox OFED
<http://www.mellanox.com/page/products_dyn?product_family=26&mtag=linux>`__ and
`Mellanox EN
<http://www.mellanox.com/page/products_dyn?product_family=27&mtag=linux>`__
include the necessary support and should be used in the meantime. For DPDK,
only libibverbs, libmlx5, mlnx-ofed-kernel packages and firmware updates are
required from that distribution.
.. note::
Several versions of Mellanox OFED/EN are available. Installing the version
this DPDK release was developed and tested against is strongly
recommended. Please check the `prerequisites`_.
Libmnl
^^^^^^
Minimal version for libmnl is **1.0.3**.
As a dependency of the **iproute2** suite, this library is often installed
by default. It is otherwise readily available through standard system
packages.
Its development headers must be installed in order to compile this PMD.
These packages are usually named **libmnl-dev** or **libmnl-devel**
depending on the Linux distribution.
Supported NICs
--------------
* Mellanox(R) ConnectX(R)-4 10G MCX4111A-XCAT (1x10G)
* Mellanox(R) ConnectX(R)-4 10G MCX4121A-XCAT (2x10G)
* Mellanox(R) ConnectX(R)-4 25G MCX4111A-ACAT (1x25G)
* Mellanox(R) ConnectX(R)-4 25G MCX4121A-ACAT (2x25G)
* Mellanox(R) ConnectX(R)-4 40G MCX4131A-BCAT (1x40G)
* Mellanox(R) ConnectX(R)-4 40G MCX413A-BCAT (1x40G)
* Mellanox(R) ConnectX(R)-4 40G MCX415A-BCAT (1x40G)
* Mellanox(R) ConnectX(R)-4 50G MCX4131A-GCAT (1x50G)
* Mellanox(R) ConnectX(R)-4 50G MCX413A-GCAT (1x50G)
* Mellanox(R) ConnectX(R)-4 50G MCX414A-BCAT (2x50G)
* Mellanox(R) ConnectX(R)-4 50G MCX415A-GCAT (2x50G)
* Mellanox(R) ConnectX(R)-4 50G MCX416A-BCAT (2x50G)
* Mellanox(R) ConnectX(R)-4 50G MCX416A-GCAT (2x50G)
* Mellanox(R) ConnectX(R)-4 50G MCX415A-CCAT (1x100G)
* Mellanox(R) ConnectX(R)-4 100G MCX416A-CCAT (2x100G)
* Mellanox(R) ConnectX(R)-4 Lx 10G MCX4121A-XCAT (2x10G)
* Mellanox(R) ConnectX(R)-4 Lx 25G MCX4121A-ACAT (2x25G)
* Mellanox(R) ConnectX(R)-5 100G MCX556A-ECAT (2x100G)
* Mellanox(R) ConnectX(R)-5 Ex EN 100G MCX516A-CDAT (2x100G)
Quick Start Guide on OFED/EN
----------------------------
1. Download latest Mellanox OFED/EN. For more info check the `prerequisites`_.
2. Install the required libraries and kernel modules either by installing
only the required set, or by installing the entire Mellanox OFED/EN:
.. code-block:: console
./mlnxofedinstall --upstream-libs --dpdk
3. Verify the firmware is the correct one:
.. code-block:: console
ibv_devinfo
4. Verify all ports links are set to Ethernet:
.. code-block:: console
mlxconfig -d <mst device> query | grep LINK_TYPE
LINK_TYPE_P1 ETH(2)
LINK_TYPE_P2 ETH(2)
Link types may have to be configured to Ethernet:
.. code-block:: console
mlxconfig -d <mst device> set LINK_TYPE_P1/2=1/2/3
* LINK_TYPE_P1=<1|2|3> , 1=Infiniband 2=Ethernet 3=VPI(auto-sense)
For hypervisors verify SR-IOV is enabled on the NIC:
.. code-block:: console
mlxconfig -d <mst device> query | grep SRIOV_EN
SRIOV_EN True(1)
If needed, set enable the set the relevant fields:
.. code-block:: console
mlxconfig -d <mst device> set SRIOV_EN=1 NUM_OF_VFS=16
mlxfwreset -d <mst device> reset
5. Restart the driver:
.. code-block:: console
/etc/init.d/openibd restart
or:
.. code-block:: console
service openibd restart
If link type was changed, firmware must be reset as well:
.. code-block:: console
mlxfwreset -d <mst device> reset
For hypervisors, after reset write the sysfs number of virtual functions
needed for the PF.
To dynamically instantiate a given number of virtual functions (VFs):
.. code-block:: console
echo [num_vfs] > /sys/class/infiniband/mlx5_0/device/sriov_numvfs
6. Compile DPDK and you are ready to go. See instructions on
:ref:`Development Kit Build System <Development_Kit_Build_System>`
Enable switchdev mode
---------------------
Switchdev mode is a mode in E-Switch, that binds between representor and VF.
Representor is a port in DPDK that is connected to a VF in such a way
that assuming there are no offload flows, each packet that is sent from the VF
will be received by the corresponding representor. While each packet that is
sent to a representor will be received by the VF.
This is very useful in case of SRIOV mode, where the first packet that is sent
by the VF will be received by the DPDK application which will decide if this
flow should be offloaded to the E-Switch. After offloading the flow packet
that the VF that are matching the flow will not be received any more by
the DPDK application.
1. Enable SRIOV mode:
.. code-block:: console
mlxconfig -d <mst device> set SRIOV_EN=true
2. Configure the max number of VFs:
.. code-block:: console
mlxconfig -d <mst device> set NUM_OF_VFS=<num of vfs>
3. Reset the FW:
.. code-block:: console
mlxfwreset -d <mst device> reset
3. Configure the actual number of VFs:
.. code-block:: console
echo <num of vfs > /sys/class/net/<net device>/device/sriov_numvfs
4. Unbind the device (can be rebind after the switchdev mode):
.. code-block:: console
echo -n "<device pci address" > /sys/bus/pci/drivers/mlx5_core/unbind
5. Enbale switchdev mode:
.. code-block:: console
echo switchdev > /sys/class/net/<net device>/compat/devlink/mode
Performance tuning
------------------
1. Configure aggressive CQE Zipping for maximum performance:
.. code-block:: console
mlxconfig -d <mst device> s CQE_COMPRESSION=1
To set it back to the default CQE Zipping mode use:
.. code-block:: console
mlxconfig -d <mst device> s CQE_COMPRESSION=0
2. In case of virtualization:
- Make sure that hypervisor kernel is 3.16 or newer.
- Configure boot with ``iommu=pt``.
- Use 1G huge pages.
- Make sure to allocate a VM on huge pages.
- Make sure to set CPU pinning.
3. Use the CPU near local NUMA node to which the PCIe adapter is connected,
for better performance. For VMs, verify that the right CPU
and NUMA node are pinned according to the above. Run:
.. code-block:: console
lstopo-no-graphics
to identify the NUMA node to which the PCIe adapter is connected.
4. If more than one adapter is used, and root complex capabilities allow
to put both adapters on the same NUMA node without PCI bandwidth degradation,
it is recommended to locate both adapters on the same NUMA node.
This in order to forward packets from one to the other without
NUMA performance penalty.
5. Disable pause frames:
.. code-block:: console
ethtool -A <netdev> rx off tx off
6. Verify IO non-posted prefetch is disabled by default. This can be checked
via the BIOS configuration. Please contact you server provider for more
information about the settings.
.. note::
On some machines, depends on the machine integrator, it is beneficial
to set the PCI max read request parameter to 1K. This can be
done in the following way:
To query the read request size use:
.. code-block:: console
setpci -s <NIC PCI address> 68.w
If the output is different than 3XXX, set it by:
.. code-block:: console
setpci -s <NIC PCI address> 68.w=3XXX
The XXX can be different on different systems. Make sure to configure
according to the setpci output.
7. To minimize overhead of searching Memory Regions:
- '--socket-mem' is recommended to pin memory by predictable amount.
- Configure per-lcore cache when creating Mempools for packet buffer.
- Refrain from dynamically allocating/freeing memory in run-time.
Supported hardware offloads using rte_flow API
----------------------------------------------
.. _Supported hardware offloads using rte_flow API:
.. table:: Supported hardware offloads using rte_flow API
+-----------------------+-----------------+-----------------+
| Offload | E-Switch | NIC |
| | | |
+=======================+=================+=================+
| Count | | DPDK 19.05 | | DPDK 19.02 |
| | | OFED 4.6 | | OFED 4.6 |
| | | RDMA-CORE V24 | | RDMA-CORE V23 |
| | | ConnectX-5 | | ConnectX-5 |
+-----------------------+-----------------+-----------------+
| Drop / Queue / RSS | | DPDK 19.05 | | DPDK 18.11 |
| | | OFED 4.6 | | OFED 4.5 |
| | | RDMA-CORE V24 | | RDMA-CORE V23 |
| | | ConnectX-5 | | ConnectX-4 |
+-----------------------+-----------------+-----------------+
| Encapsulation | | DPDK 19.05 | | DPDK 19.02 |
| (VXLAN / NVGRE / RAW) | | OFED 4.6.2 | | OFED 4.6 |
| | | RDMA-CORE V24 | | RDMA-CORE V23 |
| | | ConnectX-5 | | ConnectX-5 |
+-----------------------+-----------------+-----------------+
| Header rewrite | | DPDK 19.05 | | DPDK 19.02 |
| (set_ipv4_src / | | OFED 4.6.2 | | OFED 4.6.2 |
| set_ipv4_dst / | | RDMA-CORE V24 | | RDMA-CORE V23 |
| set_ipv6_src / | | ConnectX-5 | | ConnectX-5 |
| set_ipv6_dst / | | |
| set_tp_src / | | |
| set_tp_dst / | | |
| dec_ttl / | | |
| set_ttl / | | |
| set_mac_src / | | |
| set_mac_dst) | | |
+-----------------------+-----------------+-----------------+
| Jump | | DPDK 19.05 | | DPDK 19.02 |
| | | OFED 4.6.2 | | OFED 4.6.2 |
| | | RDMA-CORE V24 | | N/A |
| | | ConnectX-5 | | ConnectX-5 |
+-----------------------+-----------------+-----------------+
| Mark / Flag | | DPDK 19.05 | | DPDK 18.11 |
| | | OFED 4.6 | | OFED 4.5 |
| | | RDMA-CORE V24 | | RDMA-CORE V23 |
| | | ConnectX-5 | | ConnectX-4 |
+-----------------------+-----------------+-----------------+
| Port ID | | DPDK 19.05 | | N/A |
| | | OFED 4.6 | | N/A |
| | | RDMA-CORE V24 | | N/A |
| | | ConnectX-5 | | N/A |
+-----------------------+-----------------+-----------------+
* Minimum version for each component and nic.
Notes for testpmd
-----------------
Compared to librte_pmd_mlx4 that implements a single RSS configuration per
port, librte_pmd_mlx5 supports per-protocol RSS configuration.
Since ``testpmd`` defaults to IP RSS mode and there is currently no
command-line parameter to enable additional protocols (UDP and TCP as well
as IP), the following commands must be entered from its CLI to get the same
behavior as librte_pmd_mlx4:
.. code-block:: console
> port stop all
> port config all rss all
> port start all
Usage example
-------------
This section demonstrates how to launch **testpmd** with Mellanox
ConnectX-4/ConnectX-5/ConnectX-6/BlueField devices managed by librte_pmd_mlx5.
#. Load the kernel modules:
.. code-block:: console
modprobe -a ib_uverbs mlx5_core mlx5_ib
Alternatively if MLNX_OFED/MLNX_EN is fully installed, the following script
can be run:
.. code-block:: console
/etc/init.d/openibd restart
.. note::
User space I/O kernel modules (uio and igb_uio) are not used and do
not have to be loaded.
#. Make sure Ethernet interfaces are in working order and linked to kernel
verbs. Related sysfs entries should be present:
.. code-block:: console
ls -d /sys/class/net/*/device/infiniband_verbs/uverbs* | cut -d / -f 5
Example output:
.. code-block:: console
eth30
eth31
eth32
eth33
#. Optionally, retrieve their PCI bus addresses for whitelisting:
.. code-block:: console
{
for intf in eth2 eth3 eth4 eth5;
do
(cd "/sys/class/net/${intf}/device/" && pwd -P);
done;
} |
sed -n 's,.*/\(.*\),-w \1,p'
Example output:
.. code-block:: console
-w 0000:05:00.1
-w 0000:06:00.0
-w 0000:06:00.1
-w 0000:05:00.0
#. Request huge pages:
.. code-block:: console
echo 1024 > /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages/nr_hugepages
#. Start testpmd with basic parameters:
.. code-block:: console
testpmd -l 8-15 -n 4 -w 05:00.0 -w 05:00.1 -w 06:00.0 -w 06:00.1 -- --rxq=2 --txq=2 -i
Example output:
.. code-block:: console
[...]
EAL: PCI device 0000:05:00.0 on NUMA socket 0
EAL: probe driver: 15b3:1013 librte_pmd_mlx5
PMD: librte_pmd_mlx5: PCI information matches, using device "mlx5_0" (VF: false)
PMD: librte_pmd_mlx5: 1 port(s) detected
PMD: librte_pmd_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:fe
EAL: PCI device 0000:05:00.1 on NUMA socket 0
EAL: probe driver: 15b3:1013 librte_pmd_mlx5
PMD: librte_pmd_mlx5: PCI information matches, using device "mlx5_1" (VF: false)
PMD: librte_pmd_mlx5: 1 port(s) detected
PMD: librte_pmd_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:ff
EAL: PCI device 0000:06:00.0 on NUMA socket 0
EAL: probe driver: 15b3:1013 librte_pmd_mlx5
PMD: librte_pmd_mlx5: PCI information matches, using device "mlx5_2" (VF: false)
PMD: librte_pmd_mlx5: 1 port(s) detected
PMD: librte_pmd_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:fa
EAL: PCI device 0000:06:00.1 on NUMA socket 0
EAL: probe driver: 15b3:1013 librte_pmd_mlx5
PMD: librte_pmd_mlx5: PCI information matches, using device "mlx5_3" (VF: false)
PMD: librte_pmd_mlx5: 1 port(s) detected
PMD: librte_pmd_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:fb
Interactive-mode selected
Configuring Port 0 (socket 0)
PMD: librte_pmd_mlx5: 0x8cba80: TX queues number update: 0 -> 2
PMD: librte_pmd_mlx5: 0x8cba80: RX queues number update: 0 -> 2
Port 0: E4:1D:2D:E7:0C:FE
Configuring Port 1 (socket 0)
PMD: librte_pmd_mlx5: 0x8ccac8: TX queues number update: 0 -> 2
PMD: librte_pmd_mlx5: 0x8ccac8: RX queues number update: 0 -> 2
Port 1: E4:1D:2D:E7:0C:FF
Configuring Port 2 (socket 0)
PMD: librte_pmd_mlx5: 0x8cdb10: TX queues number update: 0 -> 2
PMD: librte_pmd_mlx5: 0x8cdb10: RX queues number update: 0 -> 2
Port 2: E4:1D:2D:E7:0C:FA
Configuring Port 3 (socket 0)
PMD: librte_pmd_mlx5: 0x8ceb58: TX queues number update: 0 -> 2
PMD: librte_pmd_mlx5: 0x8ceb58: RX queues number update: 0 -> 2
Port 3: E4:1D:2D:E7:0C:FB
Checking link statuses...
Port 0 Link Up - speed 40000 Mbps - full-duplex
Port 1 Link Up - speed 40000 Mbps - full-duplex
Port 2 Link Up - speed 10000 Mbps - full-duplex
Port 3 Link Up - speed 10000 Mbps - full-duplex
Done
testpmd>
Reference in New Issue View Git Blame Copy Permalink