d5f46be3d5
Some minor code change. No functionality impact. Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
321 lines
14 KiB
C
321 lines
14 KiB
C
/*******************************************************************************
|
|
|
|
Copyright (c) 2001-2015, Intel Corporation
|
|
All rights reserved.
|
|
|
|
Redistribution and use in source and binary forms, with or without
|
|
modification, are permitted provided that the following conditions are met:
|
|
|
|
1. Redistributions of source code must retain the above copyright notice,
|
|
this list of conditions and the following disclaimer.
|
|
|
|
2. Redistributions in binary form must reproduce the above copyright
|
|
notice, this list of conditions and the following disclaimer in the
|
|
documentation and/or other materials provided with the distribution.
|
|
|
|
3. Neither the name of the Intel Corporation nor the names of its
|
|
contributors may be used to endorse or promote products derived from
|
|
this software without specific prior written permission.
|
|
|
|
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
|
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
|
|
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
|
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
|
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
|
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
|
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
POSSIBILITY OF SUCH DAMAGE.
|
|
|
|
***************************************************************************/
|
|
|
|
#ifndef _E1000_ICH8LAN_H_
|
|
#define _E1000_ICH8LAN_H_
|
|
|
|
#define ICH_FLASH_GFPREG 0x0000
|
|
#define ICH_FLASH_HSFSTS 0x0004
|
|
#define ICH_FLASH_HSFCTL 0x0006
|
|
#define ICH_FLASH_FADDR 0x0008
|
|
#define ICH_FLASH_FDATA0 0x0010
|
|
|
|
/* Requires up to 10 seconds when MNG might be accessing part. */
|
|
#define ICH_FLASH_READ_COMMAND_TIMEOUT 10000000
|
|
#define ICH_FLASH_WRITE_COMMAND_TIMEOUT 10000000
|
|
#define ICH_FLASH_ERASE_COMMAND_TIMEOUT 10000000
|
|
#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
|
|
#define ICH_FLASH_CYCLE_REPEAT_COUNT 10
|
|
|
|
#define ICH_CYCLE_READ 0
|
|
#define ICH_CYCLE_WRITE 2
|
|
#define ICH_CYCLE_ERASE 3
|
|
|
|
#define FLASH_GFPREG_BASE_MASK 0x1FFF
|
|
#define FLASH_SECTOR_ADDR_SHIFT 12
|
|
|
|
#define ICH_FLASH_SEG_SIZE_256 256
|
|
#define ICH_FLASH_SEG_SIZE_4K 4096
|
|
#define ICH_FLASH_SEG_SIZE_8K 8192
|
|
#define ICH_FLASH_SEG_SIZE_64K 65536
|
|
|
|
#define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */
|
|
/* FW established a valid mode */
|
|
#define E1000_ICH_FWSM_FW_VALID 0x00008000
|
|
#define E1000_ICH_FWSM_PCIM2PCI 0x01000000 /* ME PCIm-to-PCI active */
|
|
#define E1000_ICH_FWSM_PCIM2PCI_COUNT 2000
|
|
|
|
#define E1000_ICH_MNG_IAMT_MODE 0x2
|
|
|
|
#define E1000_FWSM_WLOCK_MAC_MASK 0x0380
|
|
#define E1000_FWSM_WLOCK_MAC_SHIFT 7
|
|
#if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT)
|
|
#define E1000_FWSM_ULP_CFG_DONE 0x00000400 /* Low power cfg done */
|
|
#endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */
|
|
|
|
/* Shared Receive Address Registers */
|
|
#define E1000_SHRAL_PCH_LPT(_i) (0x05408 + ((_i) * 8))
|
|
#define E1000_SHRAH_PCH_LPT(_i) (0x0540C + ((_i) * 8))
|
|
|
|
#if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT)
|
|
#define E1000_H2ME 0x05B50 /* Host to ME */
|
|
#endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */
|
|
#if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT)
|
|
#define E1000_H2ME_ULP 0x00000800 /* ULP Indication Bit */
|
|
#define E1000_H2ME_ENFORCE_SETTINGS 0x00001000 /* Enforce Settings */
|
|
|
|
#endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */
|
|
#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \
|
|
(ID_LED_OFF1_OFF2 << 8) | \
|
|
(ID_LED_OFF1_ON2 << 4) | \
|
|
(ID_LED_DEF1_DEF2))
|
|
|
|
#define E1000_ICH_NVM_SIG_WORD 0x13
|
|
#define E1000_ICH_NVM_SIG_MASK 0xC000
|
|
#define E1000_ICH_NVM_VALID_SIG_MASK 0xC0
|
|
#define E1000_ICH_NVM_SIG_VALUE 0x80
|
|
|
|
#define E1000_ICH8_LAN_INIT_TIMEOUT 1500
|
|
|
|
#if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT)
|
|
/* FEXT register bit definition */
|
|
#define E1000_FEXT_PHY_CABLE_DISCONNECTED 0x00000004
|
|
|
|
#endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */
|
|
#define E1000_FEXTNVM_SW_CONFIG 1
|
|
#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* different on ICH8M */
|
|
|
|
#define E1000_FEXTNVM3_PHY_CFG_COUNTER_MASK 0x0C000000
|
|
#define E1000_FEXTNVM3_PHY_CFG_COUNTER_50MSEC 0x08000000
|
|
|
|
#define E1000_FEXTNVM4_BEACON_DURATION_MASK 0x7
|
|
#define E1000_FEXTNVM4_BEACON_DURATION_8USEC 0x7
|
|
#define E1000_FEXTNVM4_BEACON_DURATION_16USEC 0x3
|
|
|
|
#define E1000_FEXTNVM6_REQ_PLL_CLK 0x00000100
|
|
#define E1000_FEXTNVM6_ENABLE_K1_ENTRY_CONDITION 0x00000200
|
|
#define E1000_FEXTNVM6_K1_OFF_ENABLE 0x80000000
|
|
/* bit for disabling packet buffer read */
|
|
#define E1000_FEXTNVM7_DISABLE_PB_READ 0x00040000
|
|
#define E1000_FEXTNVM7_SIDE_CLK_UNGATE 0x00000004
|
|
#if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT)
|
|
#define E1000_FEXTNVM7_DISABLE_SMB_PERST 0x00000020
|
|
#endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */
|
|
#define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL
|
|
|
|
#define E1000_ICH_RAR_ENTRIES 7
|
|
#define E1000_PCH2_RAR_ENTRIES 5 /* RAR[0], SHRA[0-3] */
|
|
#define E1000_PCH_LPT_RAR_ENTRIES 12 /* RAR[0], SHRA[0-10] */
|
|
|
|
#define PHY_PAGE_SHIFT 5
|
|
#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
|
|
((reg) & MAX_PHY_REG_ADDRESS))
|
|
#define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */
|
|
#define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */
|
|
|
|
#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002
|
|
#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300
|
|
#define IGP3_VR_CTRL_MODE_SHUTDOWN 0x0200
|
|
|
|
/* PHY Wakeup Registers and defines */
|
|
#define BM_PORT_GEN_CFG PHY_REG(BM_PORT_CTRL_PAGE, 17)
|
|
#define BM_RCTL PHY_REG(BM_WUC_PAGE, 0)
|
|
#define BM_WUC PHY_REG(BM_WUC_PAGE, 1)
|
|
#define BM_WUFC PHY_REG(BM_WUC_PAGE, 2)
|
|
#define BM_WUS PHY_REG(BM_WUC_PAGE, 3)
|
|
#define BM_RAR_L(_i) (BM_PHY_REG(BM_WUC_PAGE, 16 + ((_i) << 2)))
|
|
#define BM_RAR_M(_i) (BM_PHY_REG(BM_WUC_PAGE, 17 + ((_i) << 2)))
|
|
#define BM_RAR_H(_i) (BM_PHY_REG(BM_WUC_PAGE, 18 + ((_i) << 2)))
|
|
#define BM_RAR_CTRL(_i) (BM_PHY_REG(BM_WUC_PAGE, 19 + ((_i) << 2)))
|
|
#define BM_MTA(_i) (BM_PHY_REG(BM_WUC_PAGE, 128 + ((_i) << 1)))
|
|
|
|
#define BM_RCTL_UPE 0x0001 /* Unicast Promiscuous Mode */
|
|
#define BM_RCTL_MPE 0x0002 /* Multicast Promiscuous Mode */
|
|
#define BM_RCTL_MO_SHIFT 3 /* Multicast Offset Shift */
|
|
#define BM_RCTL_MO_MASK (3 << 3) /* Multicast Offset Mask */
|
|
#define BM_RCTL_BAM 0x0020 /* Broadcast Accept Mode */
|
|
#define BM_RCTL_PMCF 0x0040 /* Pass MAC Control Frames */
|
|
#define BM_RCTL_RFCE 0x0080 /* Rx Flow Control Enable */
|
|
|
|
#define HV_LED_CONFIG PHY_REG(768, 30) /* LED Configuration */
|
|
#define HV_MUX_DATA_CTRL PHY_REG(776, 16)
|
|
#define HV_MUX_DATA_CTRL_GEN_TO_MAC 0x0400
|
|
#define HV_MUX_DATA_CTRL_FORCE_SPEED 0x0004
|
|
#define HV_STATS_PAGE 778
|
|
/* Half-duplex collision counts */
|
|
#define HV_SCC_UPPER PHY_REG(HV_STATS_PAGE, 16) /* Single Collision */
|
|
#define HV_SCC_LOWER PHY_REG(HV_STATS_PAGE, 17)
|
|
#define HV_ECOL_UPPER PHY_REG(HV_STATS_PAGE, 18) /* Excessive Coll. */
|
|
#define HV_ECOL_LOWER PHY_REG(HV_STATS_PAGE, 19)
|
|
#define HV_MCC_UPPER PHY_REG(HV_STATS_PAGE, 20) /* Multiple Collision */
|
|
#define HV_MCC_LOWER PHY_REG(HV_STATS_PAGE, 21)
|
|
#define HV_LATECOL_UPPER PHY_REG(HV_STATS_PAGE, 23) /* Late Collision */
|
|
#define HV_LATECOL_LOWER PHY_REG(HV_STATS_PAGE, 24)
|
|
#define HV_COLC_UPPER PHY_REG(HV_STATS_PAGE, 25) /* Collision */
|
|
#define HV_COLC_LOWER PHY_REG(HV_STATS_PAGE, 26)
|
|
#define HV_DC_UPPER PHY_REG(HV_STATS_PAGE, 27) /* Defer Count */
|
|
#define HV_DC_LOWER PHY_REG(HV_STATS_PAGE, 28)
|
|
#define HV_TNCRS_UPPER PHY_REG(HV_STATS_PAGE, 29) /* Tx with no CRS */
|
|
#define HV_TNCRS_LOWER PHY_REG(HV_STATS_PAGE, 30)
|
|
|
|
#define E1000_FCRTV_PCH 0x05F40 /* PCH Flow Control Refresh Timer Value */
|
|
|
|
#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */
|
|
#define E1000_NVM_K1_ENABLE 0x1 /* NVM Enable K1 bit */
|
|
#define K1_ENTRY_LATENCY 0
|
|
#define K1_MIN_TIME 1
|
|
|
|
/* SMBus Control Phy Register */
|
|
#define CV_SMB_CTRL PHY_REG(769, 23)
|
|
#define CV_SMB_CTRL_FORCE_SMBUS 0x0001
|
|
|
|
#if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT)
|
|
/* I218 Ultra Low Power Configuration 1 Register */
|
|
#define I218_ULP_CONFIG1 PHY_REG(779, 16)
|
|
#define I218_ULP_CONFIG1_START 0x0001 /* Start auto ULP config */
|
|
#define I218_ULP_CONFIG1_IND 0x0004 /* Pwr up from ULP indication */
|
|
#define I218_ULP_CONFIG1_STICKY_ULP 0x0010 /* Set sticky ULP mode */
|
|
#define I218_ULP_CONFIG1_INBAND_EXIT 0x0020 /* Inband on ULP exit */
|
|
#define I218_ULP_CONFIG1_WOL_HOST 0x0040 /* WoL Host on ULP exit */
|
|
#define I218_ULP_CONFIG1_RESET_TO_SMBUS 0x0100 /* Reset to SMBus mode */
|
|
#define I218_ULP_CONFIG1_DISABLE_SMB_PERST 0x1000 /* Disable on PERST# */
|
|
|
|
#endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */
|
|
/* SMBus Address Phy Register */
|
|
#define HV_SMB_ADDR PHY_REG(768, 26)
|
|
#define HV_SMB_ADDR_MASK 0x007F
|
|
#define HV_SMB_ADDR_PEC_EN 0x0200
|
|
#define HV_SMB_ADDR_VALID 0x0080
|
|
#define HV_SMB_ADDR_FREQ_MASK 0x1100
|
|
#define HV_SMB_ADDR_FREQ_LOW_SHIFT 8
|
|
#define HV_SMB_ADDR_FREQ_HIGH_SHIFT 12
|
|
|
|
/* Strapping Option Register - RO */
|
|
#define E1000_STRAP 0x0000C
|
|
#define E1000_STRAP_SMBUS_ADDRESS_MASK 0x00FE0000
|
|
#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17
|
|
#define E1000_STRAP_SMT_FREQ_MASK 0x00003000
|
|
#define E1000_STRAP_SMT_FREQ_SHIFT 12
|
|
|
|
/* OEM Bits Phy Register */
|
|
#define HV_OEM_BITS PHY_REG(768, 25)
|
|
#define HV_OEM_BITS_LPLU 0x0004 /* Low Power Link Up */
|
|
#define HV_OEM_BITS_GBE_DIS 0x0040 /* Gigabit Disable */
|
|
#define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */
|
|
|
|
/* KMRN Mode Control */
|
|
#define HV_KMRN_MODE_CTRL PHY_REG(769, 16)
|
|
#define HV_KMRN_MDIO_SLOW 0x0400
|
|
|
|
/* KMRN FIFO Control and Status */
|
|
#define HV_KMRN_FIFO_CTRLSTA PHY_REG(770, 16)
|
|
#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_MASK 0x7000
|
|
#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_SHIFT 12
|
|
|
|
/* PHY Power Management Control */
|
|
#define HV_PM_CTRL PHY_REG(770, 17)
|
|
#define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA 0x100
|
|
#define HV_PM_CTRL_K1_ENABLE 0x4000
|
|
|
|
#define SW_FLAG_TIMEOUT 1000 /* SW Semaphore flag timeout in ms */
|
|
|
|
/* Inband Control */
|
|
#define I217_INBAND_CTRL PHY_REG(770, 18)
|
|
#define I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_MASK 0x3F00
|
|
#define I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_SHIFT 8
|
|
|
|
/* Low Power Idle GPIO Control */
|
|
#define I217_LPI_GPIO_CTRL PHY_REG(772, 18)
|
|
#define I217_LPI_GPIO_CTRL_AUTO_EN_LPI 0x0800
|
|
|
|
/* PHY Low Power Idle Control */
|
|
#define I82579_LPI_CTRL PHY_REG(772, 20)
|
|
#define I82579_LPI_CTRL_100_ENABLE 0x2000
|
|
#define I82579_LPI_CTRL_1000_ENABLE 0x4000
|
|
#define I82579_LPI_CTRL_ENABLE_MASK 0x6000
|
|
|
|
/* 82579 DFT Control */
|
|
#define I82579_DFT_CTRL PHY_REG(769, 20)
|
|
#define I82579_DFT_CTRL_GATE_PHY_RESET 0x0040 /* Gate PHY Reset on MAC Reset */
|
|
|
|
/* Extended Management Interface (EMI) Registers */
|
|
#define I82579_EMI_ADDR 0x10
|
|
#define I82579_EMI_DATA 0x11
|
|
#define I82579_LPI_UPDATE_TIMER 0x4805 /* in 40ns units + 40 ns base value */
|
|
#define I82579_MSE_THRESHOLD 0x084F /* 82579 Mean Square Error Threshold */
|
|
#define I82577_MSE_THRESHOLD 0x0887 /* 82577 Mean Square Error Threshold */
|
|
#define I82579_MSE_LINK_DOWN 0x2411 /* MSE count before dropping link */
|
|
#define I82579_RX_CONFIG 0x3412 /* Receive configuration */
|
|
#define I82579_LPI_PLL_SHUT 0x4412 /* LPI PLL Shut Enable */
|
|
#define I82579_EEE_PCS_STATUS 0x182E /* IEEE MMD Register 3.1 >> 8 */
|
|
#define I82579_EEE_CAPABILITY 0x0410 /* IEEE MMD Register 3.20 */
|
|
#define I82579_EEE_ADVERTISEMENT 0x040E /* IEEE MMD Register 7.60 */
|
|
#define I82579_EEE_LP_ABILITY 0x040F /* IEEE MMD Register 7.61 */
|
|
#define I82579_EEE_100_SUPPORTED (1 << 1) /* 100BaseTx EEE */
|
|
#define I82579_EEE_1000_SUPPORTED (1 << 2) /* 1000BaseTx EEE */
|
|
#define I82579_LPI_100_PLL_SHUT (1 << 2) /* 100M LPI PLL Shut Enabled */
|
|
#define I217_EEE_PCS_STATUS 0x9401 /* IEEE MMD Register 3.1 */
|
|
#define I217_EEE_CAPABILITY 0x8000 /* IEEE MMD Register 3.20 */
|
|
#define I217_EEE_ADVERTISEMENT 0x8001 /* IEEE MMD Register 7.60 */
|
|
#define I217_EEE_LP_ABILITY 0x8002 /* IEEE MMD Register 7.61 */
|
|
#define I217_RX_CONFIG 0xB20C /* Receive configuration */
|
|
|
|
#define E1000_EEE_RX_LPI_RCVD 0x0400 /* Tx LP idle received */
|
|
#define E1000_EEE_TX_LPI_RCVD 0x0800 /* Rx LP idle received */
|
|
|
|
/* Intel Rapid Start Technology Support */
|
|
#define I217_PROXY_CTRL BM_PHY_REG(BM_WUC_PAGE, 70)
|
|
#define I217_PROXY_CTRL_AUTO_DISABLE 0x0080
|
|
#define I217_SxCTRL PHY_REG(BM_PORT_CTRL_PAGE, 28)
|
|
#define I217_SxCTRL_ENABLE_LPI_RESET 0x1000
|
|
#define I217_CGFREG PHY_REG(772, 29)
|
|
#define I217_CGFREG_ENABLE_MTA_RESET 0x0002
|
|
#define I217_MEMPWR PHY_REG(772, 26)
|
|
#define I217_MEMPWR_DISABLE_SMB_RELEASE 0x0010
|
|
|
|
/* Receive Address Initial CRC Calculation */
|
|
#define E1000_PCH_RAICC(_n) (0x05F50 + ((_n) * 4))
|
|
|
|
#if defined(QV_RELEASE) || !defined(NO_PCH_LPT_B0_SUPPORT)
|
|
#define E1000_PCI_REVISION_ID_REG 0x08
|
|
#endif /* defined(QV_RELEASE) || !defined(NO_PCH_LPT_B0_SUPPORT) */
|
|
void e1000_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
|
|
bool state);
|
|
void e1000_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
|
|
void e1000_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
|
|
void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw);
|
|
u32 e1000_resume_workarounds_pchlan(struct e1000_hw *hw);
|
|
s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
|
|
s32 e1000_configure_k0s_lpt(struct e1000_hw *hw, u8 entry_latency, u8 min_time);
|
|
void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw);
|
|
s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable);
|
|
s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
|
|
s32 e1000_write_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 data);
|
|
s32 e1000_set_eee_pchlan(struct e1000_hw *hw);
|
|
#ifdef ULP_SUPPORT
|
|
s32 e1000_enable_ulp_lpt_lp(struct e1000_hw *hw, bool to_sx);
|
|
s32 e1000_disable_ulp_lpt_lp(struct e1000_hw *hw, bool force);
|
|
#endif /* ULP_SUPPORT */
|
|
#endif /* _E1000_ICH8LAN_H_ */
|
|
void e1000_demote_ltr(struct e1000_hw *hw, bool demote, bool link);
|