120be1b92b
using "The DPDK Contributors" as decided by techboard. Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com> Acked-by: Thomas Monjalon <thomas@monjalon.net>
653 lines
21 KiB
ReStructuredText
653 lines
21 KiB
ReStructuredText
.. SPDX-License-Identifier: BSD-3-Clause
|
||
Copyright 2016 The DPDK contributors
|
||
|
||
DPDK Release 16.04
|
||
==================
|
||
|
||
|
||
New Features
|
||
------------
|
||
|
||
* **Added function to check primary process state.**
|
||
|
||
A new function ``rte_eal_primary_proc_alive()`` has been added
|
||
to allow the user to detect if a primary process is running.
|
||
Use cases for this feature include fault detection, and monitoring
|
||
using secondary processes.
|
||
|
||
* **Enabled bulk allocation of mbufs.**
|
||
|
||
A new function ``rte_pktmbuf_alloc_bulk()`` has been added to allow the user
|
||
to bulk allocate mbufs.
|
||
|
||
* **Added device link speed capabilities.**
|
||
|
||
The structure ``rte_eth_dev_info`` now has a ``speed_capa`` bitmap, which
|
||
allows the application to determine the supported speeds of each device.
|
||
|
||
* **Added bitmap of link speeds to advertise.**
|
||
|
||
Added a feature to allow the definition of a set of advertised speeds for auto-negotiation,
|
||
explicitly disabling link auto-negotiation (single speed)
|
||
and full auto-negotiation.
|
||
|
||
* **Added new poll-mode driver for Amazon Elastic Network Adapters (ENA).**
|
||
|
||
The driver operates for a variety of ENA adapters through feature negotiation
|
||
with the adapter and upgradable commands set.
|
||
The ENA driver handles PCI Physical and Virtual ENA functions.
|
||
|
||
* **Restored vmxnet3 TX data ring.**
|
||
|
||
TX data ring has been shown to improve small packet forwarding performance
|
||
on the vSphere environment.
|
||
|
||
* **Added vmxnet3 TX L4 checksum offload.**
|
||
|
||
Added support for TCP/UDP checksum offload to vmxnet3.
|
||
|
||
* **Added vmxnet3 TSO support.**
|
||
|
||
Added support for TSO to vmxnet3.
|
||
|
||
* **Added vmxnet3 support for jumbo frames.**
|
||
|
||
Added support for linking multi-segment buffers together to
|
||
handle Jumbo packets.
|
||
|
||
* **Enabled Virtio 1.0 support.**
|
||
|
||
Enabled Virtio 1.0 support for Virtio pmd driver.
|
||
|
||
* **Supported Virtio for ARM.**
|
||
|
||
Enabled Virtio support for ARMv7/v8. Tested for ARM64.
|
||
Virtio for ARM supports VFIO-noiommu mode only.
|
||
Virtio can work with other non-x86 architectures as well, like PowerPC.
|
||
|
||
* **Supported Virtio offload in vhost-user.**
|
||
|
||
Added the offload and negotiation of checksum and TSO between vhost-user and
|
||
vanilla Linux Virtio guest.
|
||
|
||
* **Added vhost-user live migration support.**
|
||
|
||
* **Added vhost driver.**
|
||
|
||
Added a virtual PMD that wraps ``librte_vhost``.
|
||
|
||
* **Added multicast promiscuous mode support on VF for ixgbe.**
|
||
|
||
Added multicast promiscuous mode support for the ixgbe VF driver so all VFs
|
||
can receive the multicast packets.
|
||
|
||
Please note if you want to use this promiscuous mode, you need both PF and VF
|
||
driver to support it. The reason is that this VF feature is configured in the PF.
|
||
If you use kernel PF driver and the dpdk VF driver, make sure the kernel PF driver supports
|
||
VF multicast promiscuous mode. If you use dpdk PF and dpdk VF ensure the PF
|
||
driver is the same version as the VF.
|
||
|
||
* **Added support for E-tag on X550.**
|
||
|
||
E-tag is defined in `802.1BR - Bridge Port Extension <http://www.ieee802.org/1/pages/802.1br.html>`_.
|
||
|
||
This feature is for the VF, but the settings are on the PF. It means
|
||
the CLIs should be used on the PF, but some of their effects will be shown on the VF.
|
||
The forwarding of E-tag packets based on GRP and E-CID_base will have an effect
|
||
on the PF. Theoretically, the E-tag packets can be forwarded to any pool/queue
|
||
but normally we'd like to forward the packets to the pools/queues belonging
|
||
to the VFs. And E-tag insertion and stripping will have an effect on VFs. When
|
||
a VF receives E-tag packets it should strip the E-tag. When the VF transmits
|
||
packets, it should insert the E-tag. Both actions can be offloaded.
|
||
|
||
When we want to use this E-tag support feature, the forwarding should be
|
||
enabled to forward the packets received by the PF to the indicated VFs. And insertion
|
||
and stripping should be enabled for VFs to offload the effort to hardware.
|
||
|
||
Features added:
|
||
|
||
* Support E-tag offloading of insertion and stripping.
|
||
* Support Forwarding E-tag packets to pools based on
|
||
GRP and E-CID_base.
|
||
|
||
* **Added support for VxLAN and NVGRE checksum off-load on X550.**
|
||
|
||
* Added support for VxLAN and NVGRE RX/TX checksum off-load on
|
||
X550. RX/TX checksum off-load is provided on both inner and
|
||
outer IP header and TCP header.
|
||
* Added functions to support VxLAN port configuration. The
|
||
default VxLAN port number is 4789 but this can be updated
|
||
programmatically.
|
||
|
||
* **Added support for new X550EM_a devices.**
|
||
|
||
Added support for new X550EM_a devices and their MAC types, X550EM_a and X550EM_a_vf.
|
||
Updated the relevant PMD to use the new devices and MAC types.
|
||
|
||
* **Added x550em_x V2 device support.**
|
||
|
||
Added support for x550em_x V2 device. Only x550em_x V1 was supported before.
|
||
A mask for V1 and V2 is defined and used to support both.
|
||
|
||
* **Supported link speed auto-negotiation on X550EM_X**
|
||
|
||
Normally the auto-negotiation is supported by firmware and software doesn't care about
|
||
it. But on x550em_x, firmware doesn't support auto-negotiation. As the ports of x550em_x
|
||
are 10GbE, if we connect the port with a peer which is 1GbE, the link will always
|
||
be down.
|
||
We added the support for auto-negotiation by software to avoid this link down issue.
|
||
|
||
* **Added software-firmware sync on X550EM_a.**
|
||
|
||
Added support for software-firmware sync for resource sharing.
|
||
Use the PHY token, shared between software-firmware for PHY access on X550EM_a.
|
||
|
||
* **Updated the i40e base driver.**
|
||
|
||
The i40e base driver was updated with changes including the
|
||
following:
|
||
|
||
* Use RX control AQ commands to read/write RX control registers.
|
||
* Add new X722 device IDs, and removed X710 one was never used.
|
||
* Expose registers for HASH/FD input set configuring.
|
||
|
||
* **Enabled PCI extended tag for i40e.**
|
||
|
||
Enabled extended tag for i40e by checking and writing corresponding PCI config
|
||
space bytes, to boost the performance.
|
||
The legacy method of reading/writing sysfile supported by kernel module igb_uio
|
||
is now deprecated.
|
||
|
||
* **Added i40e support for setting mac addresses.**
|
||
|
||
* **Added dump of i40e registers and EEPROM.**
|
||
|
||
* **Supported ether type setting of single and double VLAN for i40e**
|
||
|
||
* **Added VMDQ DCB mode in i40e.**
|
||
|
||
Added support for DCB in VMDQ mode to i40e driver.
|
||
|
||
* **Added i40e VEB switching support.**
|
||
|
||
* **Added Flow director enhancements in i40e.**
|
||
|
||
* **Added PF reset event reporting in i40e VF driver.**
|
||
|
||
* **Added fm10k RX interrupt support.**
|
||
|
||
* **Optimized fm10k TX.**
|
||
|
||
Optimized fm10k TX by freeing multiple mbufs at a time.
|
||
|
||
* **Handled error flags in fm10k vector RX.**
|
||
|
||
Parse error flags in RX descriptor and set error bits in mbuf with vector instructions.
|
||
|
||
* **Added fm10k FTAG based forwarding support.**
|
||
|
||
* **Added mlx5 flow director support.**
|
||
|
||
Added flow director support (``RTE_FDIR_MODE_PERFECT`` and
|
||
``RTE_FDIR_MODE_PERFECT_MAC_VLAN``).
|
||
|
||
Only available with Mellanox OFED >= 3.2.
|
||
|
||
* **Added mlx5 RX VLAN stripping support.**
|
||
|
||
Added support for RX VLAN stripping.
|
||
|
||
Only available with Mellanox OFED >= 3.2.
|
||
|
||
* **Added mlx5 link up/down callbacks.**
|
||
|
||
Implemented callbacks to bring link up and down.
|
||
|
||
* **Added mlx5 support for operation in secondary processes.**
|
||
|
||
Implemented TX support in secondary processes (like mlx4).
|
||
|
||
* **Added mlx5 RX CRC stripping configuration.**
|
||
|
||
Until now, CRC was always stripped. It can now be configured.
|
||
|
||
Only available with Mellanox OFED >= 3.2.
|
||
|
||
* **Added mlx5 optional packet padding by HW.**
|
||
|
||
Added an option to make PCI bus transactions rounded to a multiple of a
|
||
cache line size for better alignment.
|
||
|
||
Only available with Mellanox OFED >= 3.2.
|
||
|
||
* **Added mlx5 TX VLAN insertion support.**
|
||
|
||
Added support for TX VLAN insertion.
|
||
|
||
Only available with Mellanox OFED >= 3.2.
|
||
|
||
* **Changed szedata2 driver type from vdev to pdev.**
|
||
|
||
Previously szedata2 device had to be added by ``--vdev`` option.
|
||
Now szedata2 PMD recognizes the device automatically during EAL
|
||
initialization.
|
||
|
||
* **Added szedata2 functions for setting link up/down.**
|
||
|
||
* **Added szedata2 promiscuous and allmulticast modes.**
|
||
|
||
* **Added af_packet dynamic removal function.**
|
||
|
||
An af_packet device can now be detached using the API, like other PMD devices.
|
||
|
||
* **Increased number of next hops for LPM IPv4 to 2^24.**
|
||
|
||
The ``next_hop`` field has been extended from 8 bits to 24 bits for IPv4.
|
||
|
||
* **Added support of SNOW 3G (UEA2 and UIA2) for Intel Quick Assist devices.**
|
||
|
||
Enabled support for the SNOW 3G wireless algorithm for Intel Quick Assist devices.
|
||
Support for cipher-only and hash-only is also provided
|
||
along with algorithm-chaining operations.
|
||
|
||
* **Added SNOW3G SW PMD.**
|
||
|
||
A new Crypto PMD has been added, which provides SNOW 3G UEA2 ciphering
|
||
and SNOW3G UIA2 hashing.
|
||
|
||
* **Added AES GCM PMD.**
|
||
|
||
Added new Crypto PMD to support AES-GCM authenticated encryption and
|
||
authenticated decryption in software.
|
||
|
||
* **Added NULL Crypto PMD**
|
||
|
||
Added new Crypto PMD to support null crypto operations in software.
|
||
|
||
* **Improved IP Pipeline Application.**
|
||
|
||
The following features have been added to ip_pipeline application;
|
||
|
||
* Added CPU utilization measurement and idle cycle rate computation.
|
||
* Added link identification support through existing port-mask option or by
|
||
specifying PCI device in every LINK section in the configuration file.
|
||
* Added load balancing support in passthrough pipeline.
|
||
|
||
* **Added IPsec security gateway example.**
|
||
|
||
Added a new application implementing an IPsec Security Gateway.
|
||
|
||
|
||
Resolved Issues
|
||
---------------
|
||
|
||
Drivers
|
||
~~~~~~~
|
||
|
||
* **ethdev: Fixed overflow for 100Gbps.**
|
||
|
||
100Gbps in Mbps (100000) was exceeding the 16-bit max value of ``link_speed``
|
||
in ``rte_eth_link``.
|
||
|
||
* **ethdev: Fixed byte order consistency between fdir flow and mask.**
|
||
|
||
Fixed issue in ethdev library where the structure for setting
|
||
fdir's mask and flow entry was not consistent in byte ordering.
|
||
|
||
* **cxgbe: Fixed crash due to incorrect size allocated for RSS table.**
|
||
|
||
Fixed a segfault that occurs when accessing part of port 0's RSS
|
||
table that gets overwritten by subsequent port 1's part of the RSS
|
||
table due to incorrect size allocated for each entry in the table.
|
||
|
||
* **cxgbe: Fixed setting wrong device MTU.**
|
||
|
||
Fixed an incorrect device MTU being set due to the Ethernet header and
|
||
CRC lengths being added twice.
|
||
|
||
* **ixgbe: Fixed zeroed VF mac address.**
|
||
|
||
Resolved an issue where the VF MAC address is zeroed out in cases where the VF
|
||
driver is loaded while the PF interface is down.
|
||
The solution is to only set it when we get an ACK from the PF.
|
||
|
||
* **ixgbe: Fixed setting flow director flag twice.**
|
||
|
||
Resolved an issue where packets were being dropped when switching to perfect
|
||
filters mode.
|
||
|
||
* **ixgbe: Set MDIO speed after MAC reset.**
|
||
|
||
The MDIO clock speed must be reconfigured after the MAC reset. The MDIO clock
|
||
speed becomes invalid, therefore the driver reads invalid PHY register values.
|
||
The driver now set the MDIO clock speed prior to initializing PHY ops and
|
||
again after the MAC reset.
|
||
|
||
* **ixgbe: Fixed maximum number of available TX queues.**
|
||
|
||
In IXGBE, the maximum number of TX queues varies depending on the NIC operating
|
||
mode. This was not being updated in the device information, providing
|
||
an incorrect number in some cases.
|
||
|
||
* **i40e: Generated MAC address for each VFs.**
|
||
|
||
It generates a MAC address for each VFs during PF host initialization,
|
||
and keeps the VF MAC address the same among different VF launch.
|
||
|
||
* **i40e: Fixed failure of reading/writing RX control registers.**
|
||
|
||
Fixed i40e issue of failing to read/write rx control registers when
|
||
under stress with traffic, which might result in application launch
|
||
failure.
|
||
|
||
* **i40e: Enabled vector driver by default.**
|
||
|
||
Previously, vector driver was disabled by default as it couldn't fill packet type
|
||
info for l3fwd to work well. Now there is an option for l3fwd to analyze
|
||
the packet type so the vector driver is enabled by default.
|
||
|
||
* **i40e: Fixed link info of VF.**
|
||
|
||
Previously, the VF's link speed stayed at 10GbE and status always was up.
|
||
It did not change even when the physical link's status changed.
|
||
Now this issue is fixed to make VF's link info consistent with physical link.
|
||
|
||
* **mlx5: Fixed possible crash during initialization.**
|
||
|
||
A crash could occur when failing to allocate private device context.
|
||
|
||
* **mlx5: Added port type check.**
|
||
|
||
Added port type check to prevent port initialization on non-Ethernet link layers and
|
||
to report an error.
|
||
|
||
* **mlx5: Applied VLAN filtering to broadcast and IPv6 multicast flows.**
|
||
|
||
Prevented reception of multicast frames outside of configured VLANs.
|
||
|
||
* **mlx5: Fixed RX checksum offload in non L3/L4 packets.**
|
||
|
||
Fixed report of bad checksum for packets of unknown type.
|
||
|
||
* **aesni_mb: Fixed wrong return value when creating a device.**
|
||
|
||
The ``cryptodev_aesni_mb_init()`` function was returning the device id of the device created,
|
||
instead of 0 (on success) that ``rte_eal_vdev_init()`` expects.
|
||
This made it impossible to create more than one aesni_mb device
|
||
from the command line.
|
||
|
||
* **qat: Fixed AES GCM decryption.**
|
||
|
||
Allowed AES GCM on the cryptodev API, but in some cases gave invalid results
|
||
due to incorrect IV setting.
|
||
|
||
|
||
Libraries
|
||
~~~~~~~~~
|
||
|
||
* **hash: Fixed CRC32c hash computation for non multiple of 4 bytes sizes.**
|
||
|
||
Fix crc32c hash functions to return a valid crc32c value for data lengths
|
||
not a multiple of 4 bytes.
|
||
|
||
* **hash: Fixed hash library to support multi-process mode.**
|
||
|
||
Fix hash library to support multi-process mode, using a jump table,
|
||
instead of storing a function pointer to the key compare function.
|
||
Multi-process mode only works with the built-in compare functions,
|
||
however a custom compare function (not in the jump table) can only
|
||
be used in single-process mode.
|
||
|
||
* **hash: Fixed return value when allocating an existing hash table.**
|
||
|
||
Changed the ``rte_hash*_create()`` functions to return ``NULL`` and set
|
||
``rte_errno`` to ``EEXIST`` when the object name already exists. This is
|
||
the behavior described in the API documentation in the header file.
|
||
The previous behavior was to return a pointer to the existing object in
|
||
that case, preventing the caller from knowing if the object had to be freed
|
||
or not.
|
||
|
||
* **lpm: Fixed return value when allocating an existing object.**
|
||
|
||
Changed the ``rte_lpm*_create()`` functions to return ``NULL`` and set
|
||
``rte_errno`` to ``EEXIST`` when the object name already exists. This is
|
||
the behavior described in the API documentation in the header file.
|
||
The previous behavior was to return a pointer to the existing object in
|
||
that case, preventing the caller from knowing if the object had to be freed
|
||
or not.
|
||
|
||
* **librte_port: Fixed segmentation fault for ring and ethdev writer nodrop.**
|
||
|
||
Fixed core dump issue on txq and swq when dropless is set to yes.
|
||
|
||
|
||
Examples
|
||
~~~~~~~~
|
||
|
||
* **l3fwd-power: Fixed memory leak for non-IP packet.**
|
||
|
||
Fixed issue in l3fwd-power where, on receiving packets of types
|
||
other than IPv4 or IPv6, the mbuf was not released, and caused
|
||
a memory leak.
|
||
|
||
* **l3fwd: Fixed using packet type blindly.**
|
||
|
||
l3fwd makes use of packet type information without querying if devices or PMDs
|
||
really set it. For those devices that don't set ptypes, add an option to parse it.
|
||
|
||
* **examples/vhost: Fixed frequent mbuf allocation failure.**
|
||
|
||
The vhost-switch often fails to allocate mbuf when dequeue from vring because it
|
||
wrongly calculates the number of mbufs needed.
|
||
|
||
|
||
API Changes
|
||
-----------
|
||
|
||
* The ethdev statistics counter ``imissed`` is considered to be independent of ``ierrors``.
|
||
All drivers are now counting the missed packets only once, i.e. drivers will
|
||
not increment ierrors anymore for missed packets.
|
||
|
||
* The ethdev structure ``rte_eth_dev_info`` was changed to support device
|
||
speed capabilities.
|
||
|
||
* The ethdev structures ``rte_eth_link`` and ``rte_eth_conf`` were changed to
|
||
support the new link API.
|
||
|
||
* The functions ``rte_eth_dev_udp_tunnel_add`` and ``rte_eth_dev_udp_tunnel_delete``
|
||
have been renamed into ``rte_eth_dev_udp_tunnel_port_add`` and
|
||
``rte_eth_dev_udp_tunnel_port_delete``.
|
||
|
||
* The ``outer_mac`` and ``inner_mac`` fields in structure
|
||
``rte_eth_tunnel_filter_conf`` are changed from pointer to struct in order
|
||
to keep code's readability.
|
||
|
||
* The fields in ethdev structure ``rte_eth_fdir_masks`` were changed
|
||
to be in big endian.
|
||
|
||
* A parameter ``vlan_type`` has been added to the function
|
||
``rte_eth_dev_set_vlan_ether_type``.
|
||
|
||
* The af_packet device init function is no longer public. The device should be attached
|
||
via the API.
|
||
|
||
* The LPM ``next_hop`` field is extended from 8 bits to 24 bits for IPv4
|
||
while keeping ABI compatibility.
|
||
|
||
* A new ``rte_lpm_config`` structure is used so the LPM library will allocate
|
||
exactly the amount of memory which is necessary to hold application’s rules.
|
||
The previous ABI is kept for compatibility.
|
||
|
||
* The prototype for the pipeline input port, output port and table action
|
||
handlers are updated: the pipeline parameter is added,
|
||
the packets mask parameter has been either removed or made input-only.
|
||
|
||
|
||
ABI Changes
|
||
-----------
|
||
|
||
* The RETA entry size in ``rte_eth_rss_reta_entry64`` has been increased
|
||
from 8-bit to 16-bit.
|
||
|
||
* The ethdev flow director structure ``rte_eth_fdir_flow`` structure was
|
||
changed. New fields were added to extend flow director's input set.
|
||
|
||
* The cmdline buffer size has been increase from 256 to 512.
|
||
|
||
|
||
Shared Library Versions
|
||
-----------------------
|
||
|
||
The libraries prepended with a plus sign were incremented in this version.
|
||
|
||
.. code-block:: diff
|
||
|
||
+ libethdev.so.3
|
||
librte_acl.so.2
|
||
librte_cfgfile.so.2
|
||
+ librte_cmdline.so.2
|
||
librte_distributor.so.1
|
||
librte_eal.so.2
|
||
librte_hash.so.2
|
||
librte_ip_frag.so.1
|
||
librte_ivshmem.so.1
|
||
librte_jobstats.so.1
|
||
librte_kni.so.2
|
||
librte_kvargs.so.1
|
||
librte_lpm.so.2
|
||
librte_mbuf.so.2
|
||
librte_mempool.so.1
|
||
librte_meter.so.1
|
||
+ librte_pipeline.so.3
|
||
librte_pmd_bond.so.1
|
||
librte_pmd_ring.so.2
|
||
librte_port.so.2
|
||
librte_power.so.1
|
||
librte_reorder.so.1
|
||
librte_ring.so.1
|
||
librte_sched.so.1
|
||
librte_table.so.2
|
||
librte_timer.so.1
|
||
librte_vhost.so.2
|
||
|
||
|
||
Tested Platforms
|
||
----------------
|
||
|
||
#. SuperMicro 1U
|
||
|
||
- BIOS: 1.0c
|
||
- Processor: Intel(R) Atom(TM) CPU C2758 @ 2.40GHz
|
||
|
||
#. SuperMicro 1U
|
||
|
||
- BIOS: 1.0a
|
||
- Processor: Intel(R) Xeon(R) CPU D-1540 @ 2.00GHz
|
||
- Onboard NIC: Intel(R) X552/X557-AT (2x10G)
|
||
|
||
- Firmware-version: 0x800001cf
|
||
- Device ID (PF/VF): 8086:15ad /8086:15a8
|
||
|
||
- kernel driver version: 4.2.5 (ixgbe)
|
||
|
||
#. SuperMicro 1U
|
||
|
||
- BIOS: 1.0a
|
||
- Processor: Intel(R) Xeon(R) CPU E5-4667 v3 @ 2.00GHz
|
||
|
||
#. Intel(R) Server board S2600GZ
|
||
|
||
- BIOS: SE5C600.86B.02.02.0002.122320131210
|
||
- Processor: Intel(R) Xeon(R) CPU E5-2680 v2 @ 2.80GHz
|
||
|
||
#. Intel(R) Server board W2600CR
|
||
|
||
- BIOS: SE5C600.86B.02.01.0002.082220131453
|
||
- Processor: Intel(R) Xeon(R) CPU E5-2680 v2 @ 2.80GHz
|
||
|
||
#. Intel(R) Server board S2600CWT
|
||
|
||
- BIOS: SE5C610.86B.01.01.0009.060120151350
|
||
- Processor: Intel(R) Xeon(R) CPU E5-2699 v3 @ 2.30GHz
|
||
|
||
#. Intel(R) Server board S2600WTT
|
||
|
||
- BIOS: SE5C610.86B.01.01.0005.101720141054
|
||
- Processor: Intel(R) Xeon(R) CPU E5-2699 v3 @ 2.30GHz
|
||
|
||
#. Intel(R) Server board S2600WTT
|
||
|
||
- BIOS: SE5C610.86B.11.01.0044.090120151156
|
||
- Processor: Intel(R) Xeon(R) CPU E5-2695 v4 @ 2.10GHz
|
||
|
||
|
||
Tested NICs
|
||
-----------
|
||
|
||
#. Intel(R) Ethernet Controller X540-AT2
|
||
|
||
- Firmware version: 0x80000389
|
||
- Device id (pf): 8086:1528
|
||
- Driver version: 3.23.2 (ixgbe)
|
||
|
||
#. Intel(R) 82599ES 10 Gigabit Ethernet Controller
|
||
|
||
- Firmware version: 0x61bf0001
|
||
- Device id (pf/vf): 8086:10fb / 8086:10ed
|
||
- Driver version: 4.0.1-k (ixgbe)
|
||
|
||
#. Intel(R) Corporation Ethernet Connection X552/X557-AT 10GBASE-T
|
||
|
||
- Firmware version: 0x800001cf
|
||
- Device id (pf/vf): 8086:15ad / 8086:15a8
|
||
- Driver version: 4.2.5 (ixgbe)
|
||
|
||
#. Intel(R) Ethernet Converged Network Adapter X710-DA4 (4x10G)
|
||
|
||
- Firmware version: 5.02 0x80002284
|
||
- Device id (pf/vf): 8086:1572 / 8086:154c
|
||
- Driver version: 1.4.26 (i40e)
|
||
|
||
#. Intel(R) Ethernet Converged Network Adapter X710-DA2 (2x10G)
|
||
|
||
- Firmware version: 5.02 0x80002282
|
||
- Device id (pf/vf): 8086:1572 / 8086:154c
|
||
- Driver version: 1.4.25 (i40e)
|
||
|
||
#. Intel(R) Ethernet Converged Network Adapter XL710-QDA1 (1x40G)
|
||
|
||
- Firmware version: 5.02 0x80002281
|
||
- Device id (pf/vf): 8086:1584 / 8086:154c
|
||
- Driver version: 1.4.25 (i40e)
|
||
|
||
#. Intel(R) Ethernet Converged Network Adapter XL710-QDA2 (2X40G)
|
||
|
||
- Firmware version: 5.02 0x80002285
|
||
- Device id (pf/vf): 8086:1583 / 8086:154c
|
||
- Driver version: 1.4.25 (i40e)
|
||
|
||
#. Intel(R) 82576EB Gigabit Ethernet Controller
|
||
|
||
- Firmware version: 1.2.1
|
||
- Device id (pf): 8086:1526
|
||
- Driver version: 5.2.13-k (igb)
|
||
|
||
#. Intel(R) Ethernet Controller I210
|
||
|
||
- Firmware version: 3.16, 0x80000500, 1.304.0
|
||
- Device id (pf): 8086:1533
|
||
- Driver version: 5.2.13-k (igb)
|
||
|
||
#. Intel(R) Corporation I350 Gigabit Network Connection
|
||
|
||
- Firmware version: 1.48, 0x800006e7
|
||
- Device id (pf/vf): 8086:1521 / 8086:1520
|
||
- Driver version: 5.2.13-k (igb)
|
||
|
||
|
||
#. Intel(R) Ethernet Multi-host Controller FM10000
|
||
|
||
- Firmware version: N/A
|
||
- Device id (pf/vf): 8086:15d0
|
||
- Driver version: 0.17.0.9 (fm10k)
|