e9b3d79b06
PCI, vmbus, and auxiliary drivers printed a warning
when NUMA node had been reported as (-1) or not reported by OS:
EAL: Invalid NUMA socket, default to 0
This message and its level might confuse users because the configuration
is valid and nothing happens that requires attention or intervention.
It was also printed without the device identification and with an indent
(PCI only), which is confusing unless DEBUG logging is on to print
the header message with the device name.
Reduce level to INFO, reword the message, and suppress it when there is
only one NUMA node because NUMA awareness does not matter in this case.
Also, remove the indent for PCI.
Fixes: f0e0e86aa3 ("pci: move NUMA node check from scan to probe")
Fixes: 831dba47bd ("bus/vmbus: add Hyper-V virtual bus support")
Fixes: 1afce3086c ("bus/auxiliary: introduce auxiliary bus")
Cc: stable@dpdk.org
Signed-off-by: Dmitry Kozlyuk <dkozlyuk@nvidia.com>
Reviewed-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Reviewed-by: Xueming Li <xuemingl@nvidia.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
262 lines
8.7 KiB
ReStructuredText
262 lines
8.7 KiB
ReStructuredText
.. SPDX-License-Identifier: BSD-3-Clause
|
|
Copyright (c) 2015-2020 Amazon.com, Inc. or its affiliates.
|
|
All rights reserved.
|
|
|
|
ENA Poll Mode Driver
|
|
====================
|
|
|
|
The ENA PMD is a DPDK poll-mode driver for the Amazon Elastic
|
|
Network Adapter (ENA) family.
|
|
|
|
Overview
|
|
--------
|
|
|
|
The ENA driver exposes a lightweight management interface with a
|
|
minimal set of memory mapped registers and an extendable command set
|
|
through an Admin Queue.
|
|
|
|
The driver supports a wide range of ENA adapters, is link-speed
|
|
independent (i.e., the same driver is used for 10GbE, 25GbE, 40GbE,
|
|
etc.), and it negotiates and supports an extendable feature set.
|
|
|
|
ENA adapters allow high speed and low overhead Ethernet traffic
|
|
processing by providing a dedicated Tx/Rx queue pair per CPU core.
|
|
|
|
The ENA driver supports industry standard TCP/IP offload features such
|
|
as checksum offload and TCP transmit segmentation offload (TSO).
|
|
|
|
Receive-side scaling (RSS) is supported for multi-core scaling.
|
|
|
|
Some of the ENA devices support a working mode called Low-latency
|
|
Queue (LLQ), which saves several more microseconds.
|
|
|
|
Management Interface
|
|
--------------------
|
|
|
|
ENA management interface is exposed by means of:
|
|
|
|
* Device Registers
|
|
* Admin Queue (AQ) and Admin Completion Queue (ACQ)
|
|
|
|
ENA device memory-mapped PCIe space for registers (MMIO registers)
|
|
are accessed only during driver initialization and are not involved
|
|
in further normal device operation.
|
|
|
|
AQ is used for submitting management commands, and the
|
|
results/responses are reported asynchronously through ACQ.
|
|
|
|
ENA introduces a very small set of management commands with room for
|
|
vendor-specific extensions. Most of the management operations are
|
|
framed in a generic Get/Set feature command.
|
|
|
|
The following admin queue commands are supported:
|
|
|
|
* Create I/O submission queue
|
|
* Create I/O completion queue
|
|
* Destroy I/O submission queue
|
|
* Destroy I/O completion queue
|
|
* Get feature
|
|
* Set feature
|
|
* Get statistics
|
|
|
|
Refer to ``ena_admin_defs.h`` for the list of supported Get/Set Feature
|
|
properties.
|
|
|
|
Data Path Interface
|
|
-------------------
|
|
|
|
I/O operations are based on Tx and Rx Submission Queues (Tx SQ and Rx
|
|
SQ correspondingly). Each SQ has a completion queue (CQ) associated
|
|
with it.
|
|
|
|
The SQs and CQs are implemented as descriptor rings in contiguous
|
|
physical memory.
|
|
|
|
Refer to ``ena_eth_io_defs.h`` for the detailed structure of the descriptor
|
|
|
|
The driver supports multi-queue for both Tx and Rx.
|
|
|
|
Configuration information
|
|
-------------------------
|
|
|
|
**Runtime Configuration Parameters**
|
|
|
|
* **large_llq_hdr** (default 0)
|
|
|
|
Enables or disables usage of large LLQ headers. This option will have
|
|
effect only if the device also supports large LLQ headers. Otherwise, the
|
|
default value will be used.
|
|
|
|
**ENA Configuration Parameters**
|
|
|
|
* **Number of Queues**
|
|
|
|
This is the requested number of queues upon initialization, however, the actual
|
|
number of receive and transmit queues to be created will be the minimum between
|
|
the maximal number supported by the device and number of queues requested.
|
|
|
|
* **Size of Queues**
|
|
|
|
This is the requested size of receive/transmit queues, while the actual size
|
|
will be the minimum between the requested size and the maximal receive/transmit
|
|
supported by the device.
|
|
|
|
Building DPDK
|
|
-------------
|
|
|
|
See the :ref:`DPDK Getting Started Guide for Linux <linux_gsg>` for
|
|
instructions on how to build DPDK.
|
|
|
|
By default the ENA PMD library will be built into the DPDK library.
|
|
|
|
For configuring and using UIO and VFIO frameworks, please also refer :ref:`the
|
|
documentation that comes with DPDK suite <linux_gsg>`.
|
|
|
|
Supported ENA adapters
|
|
----------------------
|
|
|
|
Current ENA PMD supports the following ENA adapters including:
|
|
|
|
* ``1d0f:ec20`` - ENA VF
|
|
* ``1d0f:ec21`` - ENA VF RSERV0
|
|
|
|
Supported Operating Systems
|
|
---------------------------
|
|
|
|
Any Linux distribution fulfilling the conditions described in ``System Requirements``
|
|
section of :ref:`the DPDK documentation <linux_gsg>` or refer to *DPDK Release Notes*.
|
|
|
|
Supported features
|
|
------------------
|
|
|
|
* MTU configuration
|
|
* Jumbo frames up to 9K
|
|
* IPv4/TCP/UDP checksum offload
|
|
* TSO offload
|
|
* Multiple receive and transmit queues
|
|
* RSS hash
|
|
* RSS indirection table configuration
|
|
* Low Latency Queue for Tx
|
|
* Basic and extended statistics
|
|
* LSC event notification
|
|
* Watchdog (requires handling of timers in the application)
|
|
* Device reset upon failure
|
|
* Rx interrupts
|
|
|
|
Prerequisites
|
|
-------------
|
|
|
|
#. Prepare the system as recommended by DPDK suite. This includes environment
|
|
variables, hugepages configuration, tool-chains and configuration.
|
|
|
|
#. ENA PMD can operate with ``vfio-pci``(*) or ``igb_uio`` driver.
|
|
|
|
(*) ENAv2 hardware supports Low Latency Queue v2 (LLQv2). This feature
|
|
reduces the latency of the packets by pushing the header directly through
|
|
the PCI to the device, before the DMA is even triggered. For proper work
|
|
kernel PCI driver must support write combining (WC).
|
|
In DPDK ``igb_uio`` it must be enabled by loading module with
|
|
``wc_activate=1`` flag (example below). However, mainline's vfio-pci
|
|
driver in kernel doesn't have WC support yet (planed to be added).
|
|
If vfio-pci used user should be either turn off ENAv2 (to avoid performance
|
|
impact) or recompile vfio-pci driver with patch provided in
|
|
`amzn-github <https://github.com/amzn/amzn-drivers/tree/master/userspace/dpdk/enav2-vfio-patch>`_.
|
|
|
|
#. Insert ``vfio-pci`` or ``igb_uio`` kernel module using the command
|
|
``modprobe vfio-pci`` or ``modprobe uio; insmod igb_uio.ko wc_activate=1``
|
|
respectively.
|
|
|
|
#. For ``vfio-pci`` users only:
|
|
Please make sure that ``IOMMU`` is enabled in your system,
|
|
or use ``vfio`` driver in ``noiommu`` mode::
|
|
|
|
echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode
|
|
|
|
To use ``noiommu`` mode, the ``vfio-pci`` must be built with flag
|
|
``CONFIG_VFIO_NOIOMMU``.
|
|
|
|
#. Bind the intended ENA device to ``vfio-pci`` or ``igb_uio`` module.
|
|
|
|
At this point the system should be ready to run DPDK applications. Once the
|
|
application runs to completion, the ENA can be detached from attached module if
|
|
necessary.
|
|
|
|
**Rx interrupts support**
|
|
|
|
ENA PMD supports Rx interrupts, which can be used to wake up lcores waiting for
|
|
input. Please note that it won't work with ``igb_uio``, so to use this feature,
|
|
the ``vfio-pci`` should be used.
|
|
|
|
ENA handles admin interrupts and AENQ notifications on separate interrupt.
|
|
There is possibility that there won't be enough event file descriptors to
|
|
handle both admin and Rx interrupts. In that situation the Rx interrupt request
|
|
will fail.
|
|
|
|
**Note about usage on \*.metal instances**
|
|
|
|
On AWS, the metal instances are supporting IOMMU for both arm64 and x86_64
|
|
hosts.
|
|
|
|
* x86_64 (e.g. c5.metal, i3.metal):
|
|
IOMMU should be disabled by default. In that situation, the ``igb_uio`` can
|
|
be used as it is but ``vfio-pci`` should be working in no-IOMMU mode (please
|
|
see above).
|
|
|
|
When IOMMU is enabled, ``igb_uio`` cannot be used as it's not supporting this
|
|
feature, while ``vfio-pci`` should work without any changes.
|
|
To enable IOMMU on those hosts, please update ``GRUB_CMDLINE_LINUX`` in file
|
|
``/etc/default/grub`` with the below extra boot arguments::
|
|
|
|
iommu=1 intel_iommu=on
|
|
|
|
Then, make the changes live by executing as a root::
|
|
|
|
# grub2-mkconfig > /boot/grub2/grub.cfg
|
|
|
|
Finally, reboot should result in IOMMU being enabled.
|
|
|
|
* arm64 (a1.metal):
|
|
IOMMU should be enabled by default. Unfortunately, ``vfio-pci`` isn't
|
|
supporting SMMU, which is implementation of IOMMU for arm64 architecture and
|
|
``igb_uio`` isn't supporting IOMMU at all, so to use DPDK with ENA on those
|
|
hosts, one must disable IOMMU. This can be done by updating
|
|
``GRUB_CMDLINE_LINUX`` in file ``/etc/default/grub`` with the extra boot
|
|
argument::
|
|
|
|
iommu.passthrough=1
|
|
|
|
Then, make the changes live by executing as a root::
|
|
|
|
# grub2-mkconfig > /boot/grub2/grub.cfg
|
|
|
|
Finally, reboot should result in IOMMU being disabled.
|
|
Without IOMMU, ``igb_uio`` can be used as it is but ``vfio-pci`` should be
|
|
working in no-IOMMU mode (please see above).
|
|
|
|
Usage example
|
|
-------------
|
|
|
|
Follow instructions available in the document
|
|
:ref:`compiling and testing a PMD for a NIC <pmd_build_and_test>` to launch
|
|
**testpmd** with Amazon ENA devices managed by librte_net_ena.
|
|
|
|
Example output:
|
|
|
|
.. code-block:: console
|
|
|
|
[...]
|
|
EAL: PCI device 0000:00:06.0 on NUMA socket -1
|
|
EAL: Device 0000:00:06.0 is not NUMA-aware, defaulting socket to 0
|
|
EAL: probe driver: 1d0f:ec20 net_ena
|
|
|
|
Interactive-mode selected
|
|
testpmd: create a new mbuf pool <mbuf_pool_socket_0>: n=171456, size=2176, socket=0
|
|
testpmd: preferred mempool ops selected: ring_mp_mc
|
|
Warning! port-topology=paired and odd forward ports number, the last port will pair with itself.
|
|
Configuring Port 0 (socket 0)
|
|
Port 0: 00:00:00:11:00:01
|
|
Checking link statuses...
|
|
|
|
Done
|
|
testpmd>
|