iSCSI hotremove is broken. It relies on C undefined
behavior. Some bdev_io may be put after their bdev_channel
has been put (freed) and spdk_bdev_put_io may be reading
freed bdev_channel memory.
iSCSI tasks targetting hotremoved devices are finished
immediately. That's usually fine, but these tasks might
be subtasks of an r2t chain. Once subtasks are freed, their
parent task may be eventually freed as well. If the parent
has finished before the hotremoval, its bdev_io has been
assigned, so freeing the task will put that bdev_io and that's
where undefined behavior hits.
There's an ongoing work towards deferring iSCSI hotremove
if r2t tasks are present, so this test should be reenabled
once that's done.
Change-Id: I7fa741b8749d542bcabb211a0969da5d7742eda3
Signed-off-by: Dariusz Stojaczyk <dariuszx.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/410176
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Network namespaces are used to assure that kernel
is not routing packets within host stack,
but they go through veth interfaces.
This patch serves as a base for future VPP test changes,
where namespaces are used as well.
Change-Id: Ic7b82b0a0837bca2e16774fde244348a691fe056
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405641
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Change-Id: Icb98e4628962591da32d169853d0ff14400e1e50
Signed-off-by: Liang Yan <liang.z.yan@intel.com>
Reviewed-on: https://review.gerrithub.io/406922
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Ceph monitor IP address was always 127.0.0.1, with this change
it can be configured at setup time.
Since each test might prefer to specify different addresses
or ones that do not exist at start of autotest.sh. rbd_setup was
moved to begining of each test respectively.
Change-Id: I5626f7ea979d0db921208355ba23314cf48e971f
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/407910
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
At this time all iSCSI tests were using local address
127.0.0.1 for both sides of connection.
This patch changes iSCSI tests to use separate
veth (virtual ethernet) interfaces.
It will allow to actually verify functionality when using
different target and initiator IPs.
Veth are used as most closely resembling real enviroment
in single host and without any network hardware required.
This patch serves as a base for future VPP test changes,
where veth interfaces are used as well.
Note: Netmask changed to /30 temporarily and
verify_iscsi_connection_rpc_methods in rpc_config disabled.
Kernel will route trafic between two veth interfaces through
host stack. This causes target and initiator IPs
to be not as expected. Those are changed back in next patch
by adding namespaces.
Change-Id: Ida8fce107e8262bef94b2161e0197c45f6e3f070
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405552
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
NVML (Non Volatile Memory Library) changed its name to
PMDK (Persistent Memory Development Kit), so make the
necessary changes to the SPDK repository.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Id07a87eafb4e9a3099603030c58c0e927bafa608
Reviewed-on: https://review.gerrithub.io/406256
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
This patch changes hardcoded value for target IP to one from
common.sh.
Config file here should be replaced with RPC in the future.
Change-Id: I24ef413fcb9369a74b1db182338b5b41e0874a55
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/406364
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Add iscsi filesystem test cases(run fio) with
lvol and nvme backend in nightly.
Change-Id: I822e5c570fb9ef96ce63bf1c853c537b35c8b1d7
Signed-off-by: xuhuagen <huagenx.xu@intel.com>
Reviewed-on: https://review.gerrithub.io/405513
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
In function verify_iscsi_connection_rpc_methods fixed
initiator address verification. It was used addres for target. From now
it is used separate addres for initiator.
Change-Id: I46ee7ab758b24342b6a25553a62a517914e9b70e
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Reviewed-on: https://review.gerrithub.io/405582
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Target IP for Calsoft tests was hardcoded in config file.
Now it will be based on iSCSI tests common configuration.
Change-Id: Ic8db40b02d2be59f5fac5cb4503cc0c80b24cd91
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405865
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Change-Id: Ia536d956c7393c244afc29d44196207ac73f48be
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405545
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I58b53634fea07db219b20ee5b74cf31e708279a1
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405548
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This moves all iSCSI configuration to common.sh that
should be sourced in each test file.
When particular tests requires different configuration,
it can overwrite those values.
(See ip_migration.sh)
Change-Id: Ia5f684142fb910184809ee7efe74b5a51063b374
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405547
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This makes it clear and common among all iSCSI scripts
what ISCSI_PORT is refers to.
Change-Id: I01924179fb304b9cd111c39ff1b07aa3427d2c0c
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405544
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Previously values for iSCSI configuration were hardcoded
within the rpc_config script. Now it takes arguments
from bash script above.
This is base for making iSCSI configuration
common among all test scripts.
Change-Id: I1fecdd87bc11fe053590a4e25c9020cb9085eb30
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405543
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
add_initiator_group accepts netmask in IP/MASK format
and that should be sufficient for the current rpc_config tests.
This is base for future change to parametrize arguments
in this script.
Change-Id: I53346ec7af11c3266acc3d186a81b5948f7f2919
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405542
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Use nvme bdev with lvol to replace malloc bdev to test filesystem.
Change-Id: I74243675dd65d9f007a6eef1444b73f251afe95f
Signed-off-by: xuhuagen <huagenx.xu@intel.com>
Reviewed-on: https://review.gerrithub.io/403167
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch leverages bdevperf, which configures
an iscsi initiator bdev to test iSCSI target.
Change-Id: I94c9299ef1f286a13678495d270326f4616c6241
Signed-off-by: Ziye Yang <optimistyzy@gmail.com>
Reviewed-on: https://review.gerrithub.io/404068
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ia1310c136fbfef608590326edc9f7dae8f2e5fe9
Signed-off-by: Liang Yan <liang.z.yan@intel.com>
Reviewed-on: https://review.gerrithub.io/403912
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I428d1be7db33efc1a44fa3f703ca154179fad2c0
Signed-off-by: Liang Yan <liang.z.yan@intel.com>
Reviewed-on: https://review.gerrithub.io/403441
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
This will allow us to reduce core assignments for build pool vms to 8.
Change-Id: I405a12f2c1041f77f90add0b5d27abd75f7b948d
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/403559
Reviewed-by: John Kariuki <John.K.Kariuki@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This test is incorrect - it sends immediate data
greater than negotiated FirstBurstLength, but
expects an R2T. This is illegal and SPDK is
rejecting the PDU correctly.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I52220e07fa32819ee7a4ba4e6e88a1a7328d207f
Reviewed-on: https://review.gerrithub.io/403213
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ziye Yang <optimistyzy@gmail.com>
This is the first step in reorganizing the spdk test heirarchy.
Change-Id: I83467653af2da2a53251649092bed6902d6cb86e
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/401707
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This is a TODO from long ago. Complete this while adjusting dump()
and construct() format of target.
Besides names of variables and parameters about CHAP are not unified
between JSON-RPC and SPDK internal. JSON-RPC's wording looks better
and adjust SPDK internal to JSON-RPC.
Change-Id: I89bcd1ce13a11f7d63a62d51ef094dd302186d37
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/400201
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
This is a TODO from long ago. Complete this while adjusting dump()
and construct() format of target.
Change-Id: I44348ec404cae8882086a1a71a65914c9bafccc3
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/400202
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Adding new initiator to an existing initiator group to allow login
will be usual. This patch support the following JSON-RPC commands:
- add_initiators_to_initiator_group
- delete_initiators_from_initiator_group
Both initiator's name and netmask are optional but already added
name or netmask cannot be added.
Test code is added too.
Change-Id: Ic101210b9d00c2b36e37ece23fcba8cfe8e44eb8
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/398361
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
This patch is used to test iscsi target with 30 target_node connection.
Each target_node uses one lvol bdev based on lvol store and nvme bdev.
Change-Id: I233ed6a32b417b23f2c01975a6c7fce0f46f22f3
Signed-off-by: Hailiang Wang <hailiangx.e.wang@intel.com>
Reviewed-on: https://review.gerrithub.io/389431
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
This isn't a significant effort to fix, so let's just enable it to move
closer to the official Python PEP 8 guidelines.
Fix up the existing instances where we didn't already have two lines
between functions, and re-enable the pep8 warning.
Change-Id: I9cf5e7e32b9c6dfedbd1b0f9bc92951cbb2c8a0d
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/399949
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
iscsiadm installed by some Fedora releases, like Fedora 27,
loses DataDigest parameter unintelligibly.
Change-Id: I6664146c6e0cb8933188b29166bedd087f4d38e1
Signed-off-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/396076
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Some upcoming changes will effectively render this moot
anyways by adding an epoll/kqueue descriptor to poll
on in all cases (not just connections that have been
idle for 5ms).
The epoll/kqueue code was just ifdef'd out instead
of removed - some of this code will be useful
and reusable with minimal changes in the upcoming
patches.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I0c354390537e6369cb3c32e78a59c300dec6d098
Reviewed-on: https://review.gerrithub.io/395553
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: <shuhei.matsumoto.xt@hitachi.com>
Currently setting cpumask to portal is possible only through
iSCSI.conf. This patch makes possible for any user to set cpumask
through JSON-RPC too.
The following are done in this patch:
- To keep compatibility, cpumask parameter handled as optional.
- Python test code is added.
- Current python script for JSON-RPC does not work correctly for
IPv6 and the issue is fixed.
Change-Id: I42ef397ce95040a36db4430417a35e9e97527477
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/391728
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
This patch makes possible to set and get Header Digest and Data
Digest of target.
Change-Id: I1d1b892f9dfb747c0f5ad8fc4fddef40929b4143
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/394482
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Add JSON-RPC to add an LUN to an existing target. The parameter
lun_id is optinal and if skipped, the lowest free LUN ID will be
assigned.
This JSON-RPC is tested in iscsi_tgt/rpc_config.
Change-Id: I010619f2d4ccec89c589bb0618466b4d15949ebb
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/385181
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
iscsi_tgt tests with different header and data
digests configuration.
Change-Id: I6e444eacccebccd66c099ea349be4bdeb063ba67
Signed-off-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/393717
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ziye Yang <optimistyzy@gmail.com>
Reviewed-by: <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
There is no need to keep a lun name anymore - we always
use the bdev name as the lun name so it is not providing any
additional value. This also keeps us from associating
the same bdev with different LUNs on different iSCSI target
nodes or vhost-scsi controllers.
Side effect of this change is:
1) Use "bdev_name" across the APIs to make it more clear
what these names refer to.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I3d42fde22087352ce1d5dc80178bd8c5cac8cb7c
Reviewed-on: https://review.gerrithub.io/390843
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I21be11c2a8428fdc711c404bf3ce489979159ed5
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/393712
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: <shuhei.matsumoto.xt@hitachi.com>
The iscsi_tgt test scripts can assume that the default case is testing
on a local machine using the kernel TCP stack; add a fallback TARGET_IP
and INITIATOR_IP to make it easier to run the individual iSCSI tests
outside of the autotest.sh framework.
Change-Id: I07c58201691dc5f053d5f67787768dfee4110f73
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/393214
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
In the iSCSI specification, the SCSI device name is defined to be
the iSCSI name of the node.
However, when g_spdk_iscsi.nodebase is used, the SCSI device name
is made of the device specific string (the part of IQN after the
colon).
The size of the temporary buffer fullname[MAX_TMPBUF] in
spdk_iscsi_tgt_node_construct() is 1024 and the size of
spdk_scsi_dev.name is 255. The former is larger than the later.
However the max length of IQN, EUI, NAA are 223, 20, and 36,
respectively. All are less than 255.
Hence even if we use fullname as the SCSI device name, no overflow
will occur. Even if fullname is more than 255, strncpy() does not
write more than 255 in spdk_scsi_dev_construct().
It's possible to check the length of iSCSI name strictly, but I
will do the least in this patch.
Change-Id: Icc6655fcd846797720867c10e316d2951c664030
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/390360
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
1) move iscsi_pmem to nightly
2) move idle_migration to nightly
3) reduce number of malloc bdevs and lvols for iscsi_lvol
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I63fa5a2634c6edb08db16267972fd21c20fd84f4
Reviewed-on: https://review.gerrithub.io/391976
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
ext4test takes ~80 seconds to run, which is a significant portion of the
overall test time for machines running the iSCSI tests.
Change-Id: Id6384fe023f101d4e81bc4ed2da9a53a817d2a02
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/391317
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This test ran for 10 minutes, which is half of the allotted time for
the entire nightly test run.
Additionally, we should be testing each bdev backend at the component
level (e.g. via bdevio and bdevperf), rather than trying to add tests
for the whole matrix of front-end app (iscsi_tgt, nvmf_tgt, etc.) with
each bdev backend.
Change-Id: I10311e3e5092084dc939ab8662e8312066ecab6e
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/391303
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Check the SPDK_TEST_NVMF flag before running the iscsi_tgt + NVMe-oF
host test.
Change-Id: I0d545c98f188edefc089fb79e2879d5d307726f5
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/391027
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ziye Yang <optimistyzy@gmail.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Struct spdk_scsi_lun has the claimed flag as a member.
However the claimed flag is no longer required.
Moreover the claimed flag itself is not used but
spdk_scsi_lun_claim() and _unclaim() functions are used in the
UT code by hard to understand manner. Moving the logic into
spdk_scsi_lun_construct() and _destruct() in the UT code will
be more natural.
Hence remove the claimed flag from LUN and do a little refactoring
in the UT code.
Change-Id: Ica9680b49bbdb5be7c5c4161210fb3a6dcb35229
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/390566
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
A previous commit modified this test to specify the RPC address via
command line, but failed to remove the [Rpc] section from the
configuration file.
Fixes: 59515ed6f8 ("test/iscsi/ip_migration: use UNIX socket for RPC")
Change-Id: Ibd5ac69c8e72fefc7e7b540df280d8a55b0b9946
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/390326
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I3cbb52cd9a4201704423b49eae74935b8a33b0fd
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/389903
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
