Given enum was not aligned with spec. This status can be reported when
size equals 0.
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: If51f6b051c13880c1fd4e6bb0a02f134b28b5a88
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/928
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
To track the ZCopy IO stats like IOs and Bytes read and written.
Change-Id: Iab2c4d8397aee5d746db9491bd4e8ac4eea69529
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/539
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
When we unlock a range, we remove the range from the
locked bdev list before doing the for_each_channel
iteration to remove the range from each channel.
But at the same time, right after removing from the
locked list, a new lock on that range could start.
In that case, we also do a for_each_channel to add
the range to each channel, and that will race with
the for_each_channel remove. When the lock start
wins, it finds the range already in the channel,
but doesn't set the owner_range which results in
a seg fault when the for_each_channel completes.
The fix is actually rather simple. We just add the
locked_ctx to the comparison when checking if the
range is already in the channel. If the locked_ctx
matches, then we know it was added as part of
initializing a new channel. If it doesn't, then
we create a new range object pointing to the new
locked_ctx. The first one will get removed when
the remove for_each_channel catches up.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I94f8b20376dd437f404add35744d42fc148303ff
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/482620
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
If a locking operation has to wait because of an
existing lock, we queue the lock context. When the
existing lock finishes unlocking, we restart the
queued lock context. But we have to make sure
we restart the lock context on the same thread it
was originally submitted, since it has a channel
associated with it.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I555515f3adfc3c13a86584c601ed541d605980b7
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/482463
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This function is required for NVMf implementation
for compare and write fused command.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: If41611f5c0b8e4ed8eec66f09858c724f1800d59
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477914
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Added new function for getting NVMe specific return code
for fused commands. Also changed one of the return codes
in fused commands so that we could distinguish error
cases.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I86417ea4f5b8f3e6496162be3d6c6128076e35d4
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/481666
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
A new API was added `spdk_bdev_io_get_aux_buf` allowing the caller to request
an auxiliary buffer for its own private use. The API is used in the same manner that
`spdk_bdev_io_get_buf` is used and the length of the buffer is always the same as the
bdev_io primary buffer. 'spdk_bdev_io_put_aux_buf' is called to free the
auxiliary buffer.
The initial use case is crypto, in the next patch in series it is used. No UT were
added as the logic isn't that complicated and it is fully tested with each run
of crypto.
Fixed a comment typo also (not mine for once).
Signed-off-by: paul luse <paul.e.luse@intel.com>
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ib1939fcbc8e5db36fd909ef26771a725a551e8e6
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478383
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This will allow for some reuse in future patches adding
support to get auxiliary buffers from the bdev memory
pools.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Icd4e71d0e918cfe940c749e40cd1cc6c560e25a9
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/482022
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This will be helpful in future patches where auxiliary
buffer support is added, and we have a different
type of callback to invoke.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I81d2cf3057e706a0e68de87a20b24c194205bbd5
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/482021
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
To clarify what seems like it might be unintentional.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Id14b49e8b7bc2372ecb8dd7579e6797a395c2cf2
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477363
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Compare and write fused operation num_blocks should
not exceed value of 'atomic compare and write unit'.
In case of NVMe native support we should read this
value from 'namespace atomic compare and write unit'
if set in namespace identify data, otherwise from
'atomic and write unit' field in controller identify
data. If bdev does not support this natively we should
set this value to 1.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: Ib1ea02dbf9d1eed476d9dd0114ea96b1376e0c45
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477911
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Added new field in bdev_io structure for tracking
number of IO retries. It will be used in future patches.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I8e002e93f54c9ce39c7af0dd3a1960e6aea93580
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479828
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
We will only support a vectored variant of
compare-and-write for now.
This does no locking for now. Ii will be added
in a separate patch.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I5bd075c912de60090e19cf8fced19c4879fcc900
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475941
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
We can't allow overlapped locked ranges - otherwise
two different channels could be deadlocked.
So add a pending_locked_ranges to the bdev. When we
start a lock operation, check if the new range overlaps
one that's already locked. If so, put it on the pending
list. When an unlock operation completes, we will
check if any pending ranges can now be locked.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I2e3113216a195887b954533495ff200df14fadc1
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478537
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Keep a mutex protected list of the active locked ranges
in the bdev itself. This is only accessed when a new
channel is created, so that it can be populated with
the currently locked ranges.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Id68311b46ad4983b6bc9b0e1a8664d121a7e9f8e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477871
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add an io_locked TAILQ to each channel, which hold
IO that will write to a currently locked region.
Also add a new step to the locking process per channel.
Each channel needs to wait until all existing outstanding
writes to the newly locked range have been completed.
Only the channel that locked an LBA range may submit
write I/O to it. It must use the same cb_arg for the
write I/O as the cb_arg used when locking the LBA range.
This ensures that only the specific I/O operations needing
the lock will bypass the lock.
When a range is unlocked, we will just blindly try to
resubmit all IO in the io_locked tailq. This could be
made more efficient in the future, but we don't expect
this path to occur very often, so going for simplicity
in the first pass.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ibdc992144dfaffe7c05471a5b3c020cedd8cdfc3
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478226
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This adds new internal APIs bdev_lock_lba_range and
bdev_unlock_lba_range. To start, these APIs will
manage dissemination of lock/unlock requests to all
existing channels for a given bdev. This does not
yet interact at all with any I/O sent to the channel.
Future patches will check new I/O to see if they
are trying to write to a range that is locked. Future
patches will also ensure we do not have overlapping
ranges active at once.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I6d5b1cc84b41a7adc2a3c5791c766bb77376581f
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478225
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This will be used by upcoming patches for implementing
LBA range locks.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ifa4ad8dcc0d09ccf20d35f010fcae19dcc17abc9
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478224
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
In the case of bdev initialization, the memory could
not be allocated. When cleaning up, it needs to check
whether the memory pointer is valid or not before
touching the address of the pointer.
This is to fix below issue:
https://github.com/spdk/spdk/issues/1126
Change-Id: Iec0e2c5a40ad153a96fb939414a15ac3b9112a01
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478849
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: <box.b.chen@intel.com>
Reviewed-by: yidong0635 <dongx.yi@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
These bdevs claim native support for zcopy operations. They should
actually support them when running on top of a bdev that claims zcopy
support.
For example, if you were to build a part or passthru bdev on top of a
malloc_bdev (which is just for testing primarily) and then try to run
bdevperf on top of that, you will currently get errors. This patch fixes
that problem.
Change-Id: I023557a3a5b1baf177cc29f1cbc1cd391cc67a8a
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478243
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Media management event was introduced. It's sent out to notify that
some portion of the data needs to be rewritten (e.g. due to data
refresh, wear leveling, high error rate, etc.). This type of
notification is only utilized by devices exposing raw access to the
physical medium (e.g. Open Channel SSDs).
Change-Id: Ia30faa5866d71fd597009b441f69c609de974161
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471460
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Create a local variable for the spdk_bdev_channel
pointer. This will be used again later in this patch
series.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I71bef863c422e60294b5249bf65f62d4939d1a53
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477870
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Add an API so that the user can enable/disable the bdev IO
timeout. Also, add the bdev io timeout handling callback.
So it means to let the upper user determine how to handle
the IO timeout scenario reset the device or abort the IO.
Change-Id: I9c7138ca46c74c045b687adab59a18d6bccc4996
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469228
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Previously, when additional resets were submitted while a reset was in
progress, those resets were queued and then executed serially as part of
executing the original reset. Doing multiple resets on a bdev in quick
succession is not useful if the first reset succeeds and is very
unlikely to be useful in the negative case. Instead, we should batch
resets and complete them all at once when the current reset succeeds or
fails.
Change-Id: If10e0f37526860eaeeb41a8803d6298a3eff3212
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/474599
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Add the tsc trace for the parent bdev_io.
Change-Id: Idf5c5df3953fa1697c384a4f83b591584dd30a80
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476588
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The reset cmd and parent of splited IO would not go into
the _bdev_io_submit() so they don't record the submitted
time. The timeout IO check needs the submitted time so we
add them in this patch.
Change-Id: Ic7217171ec878d4a6dfa80d6635957ca0186928b
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476050
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Add a link to the bdev channel for linking all the bdev
IOs that were submitted to this channel so that we can
monitor each IO's consuming-time.
Change-Id: I1e425b2059f20fd7b158eb3d6b023ce8629e7a30
Signed-off-by: JinYu <jin.yu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469227
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The _ was supposed to indicate an internal function,
but really leaving off the spdk in the function
is the standard way to denote an internal function.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I74facafb67b793502838b9c1b5f90aec2c88c69b
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475033
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
We try to reserve the spdk_ prefix for functions that
are part of the public SPDK API.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I0a95ba0f9db04b588a2e948427f8a9f53a7b5740
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475032
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
This function is not part of the SPDK public API, so
remove the spdk_ prefix from it to make it more clear
this is internal to the SPDK bdev library.
Also add "channel" to the name since this function is
operating on the channel parameter.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I57897ab4bf601b90551259b7cf6efa63152ed02f
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475031
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
This is not part of the public SPDK API, so remove
the spdk_ prefix to make it clear this is internal
to the bdev library.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ibda76e4d8e34dde0c2fe638cb965e5ba2d9e47b5
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475030
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
This function is not part of the SPDK public API, so
remove the spdk_ prefix to make that more clear when
reading the code.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I5ea4c04c474a6cf0862f11921daa97c9df728e96
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475029
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
In emulated zero copy mode on devices with separate metadata support
the start zero copy request could assert after read completion,
during _bdev_io_unset_bounce_buf; the original iovs would be NULL, but
original md_buf would have garbage data.
Signed-off-by: Kozlowski Mateusz <mateusz.kozlowski@intel.com>
Change-Id: Ia52b012c1b7462ebe490c29f5493168775646848
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/473455
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This change allows setting of the NVMe completion queue
CDW0 in spdk_bdev_io_complete_nvme_status.
Before that change, handling of vendor specific NVMe IO
commands was limited since there wasn't a way to return
command specific info back to the initiator.
Change-Id: I250d5df3bd1e62ddb89a011503d42bd4c8390f9b
Signed-off-by: Michael Haeuptle <michael.haeuptle@hpe.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470678
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
When splitting bdev's, if we run out of child IOVs, we have to
make sure that we end block aligned. That may require us to
shorten or eliminate one or more child IOVs to be picked up
on the next split. If we eliminate enough such that there
are no IOVs for this split IO, just continue and the next
split completion will kick off another split to pick up
the remaining data to be transferred.
Fixes issue #981
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: If2bfbe5f0862295e1d74cbea00692890a2178967
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471313
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
When we ran out of child_iov space, ensure the iovs to be aligned
with block size. However the calculation was wrong.
(to_next_boundary_bytes % blocklen) meant not to_last_block but to_next_block.
So calculate to_last_block_size by reducing to_last_block_size from blocklen.
The data was collected when the issue occured. So add unit test
by using the data.
Fixes#979
Reported-by: Geoffrey McRae <geoff@hostfission.com>
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I62a50bada450288ea7c60aec0e557c2a53cd8916
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470806
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch adds reference counter and gurading mutex to bdev_desc
structure to keep track of in-flight messages and avoid release of
descriptor until all of messages has been processed. With reference
counter existing remove_scheduled field in descriptor structure is not
needed anymore.
Signed-off-by: Evgeniy Kochetov <evgeniik@mellanox.com>
Signed-off-by: Sasha Kotchubievsky <sashakot@mellanox.com>
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I97f78955362b04131abf202ba04e6d60343f3faf
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469620
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
spdk_bdev_zone_append() allows writing to
open zone from multiple threads or from
single thread with queue depth greater than
one. Zone first logical address and number of
blocks to be written are provided by user.
Logical block address of written data is
returned in completion callback.
Change-Id: I4da994d72b7e0fe6621962e3b0f2380940ec3b45
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/461614
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
spdk_bdev_io_get_append_location() will be
used during zone append command to retrieve
location of data write.
Change-Id: I1f46ae9d2f745aa53264c1a01da3f7cef4f38c72
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469164
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
spdk_bdev_zone_management() allows to perform
management action on a zone. Zone is specified
by start logical block address. Available zone
actions: open, close, reset and finish.
Change-Id: Ie7eaed3e2cc7b9b49dd51ee2d6c28b4ef2f23eb9
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/460647
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
spdk_bdev_get_zone_info() is used for retriving
information about zones inside zoned namespace.
Change-Id: I8f931505245e984c0b1ee35ed6592c978ee47544
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/460643
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Some internal bdev.c static function will be shared
with new zoned bdev module.
Change-Id: Ifbb8bf443f67b2daf97858b15d474ecce98a9efb
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469100
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Added new public header for zoned bdev. Zoned bdev is an
extension of the bdev interface. Generic concept comes
from ATA/SCSI and is also being worked as an NVMe TP.
Zoned device logical blocks space is divided into fixed-sized
zones. Each zone is described by its start logical block address
and capacity. Writes to a single zone need to be sequential.
After zone is fully written it need to be reset to write to it
again. Such writing schema could be very beneficial in terms of
write amplification factor for NAND based devices.
SPDK Flash Translation Layer library will be consuming this
interface in the future.
Extending SPDK bdev interface will allow to use existing bdev
infrastructure for this new type of devices.
Zoned device have several properties defined in spdk_bdev
structure:
- zone_size: default size of each zone
- max_open_zone: maximum number of open zones
- optimal_open_zones: optimal number of open zones to get
best performance on writes
Single zone properties are defined in spdk_bdev_zone_info
structure:
- start_lba: first logical block of z zone
- write_pointer: logical block address in the zone at
which next write shall occur.
- capacity: maximum number of logical blocks that may
be written in the zone when zone is empty.
- state: zone state
Several zone states are defined: Empty, Open, Full, Closed,
Read Only and Offline.
To change zone state zone actions are defined: Close, Finish,
Open and Reset.
Change-Id: I5fcc22d548c15743329344cae96f5ff73e268504
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/460642
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
This patch is entry point for extending bdev
interface to support devices with zoned namespace
semantics.
spdk_bdev_is_zoned() will allow user to check if
bdev is zoned bdev.
Change-Id: Id9ea9898d406d1d942bf3081b00ebcb574ac2b5e
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/460641
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Added write_unit_size field to bdev structure.
It describes required number of logical blocks
for write operation. For legacy bdevs this value
will be equal to logical block size.
For bdevs working on top of Open Channel/Zoned
Namespace SSDs or RAID 5 volumes write size unit
could be greater than logical block size and
upper layer should perform write operations
with size of multiple of write unit size.
Change-Id: I55eb6687912a7d0d1157874b2778e7d6c2d44e37
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463802
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
spdk_bdev_part_construct() must be now called on the
same thread that called spdk_bdev_part_base_construct().
This was always the case so far and I don't see any other
case where thread safety could be useful, so just remove
it. The doxygen doesn't say anything about it either.
Even in GPT case, we create a base directly as a part of
examine and then create part bdevs in the spdk_bdev_read()
completion callback, but that callback will be always
executed on the same thread which issued the read.
Change-Id: I752f2a7f08c9faf4231ed53a46b700b33fa13697
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466024
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch adds new interface for opening bdev and
implements new style remove event. With that changes
user can be notified about different types of events
that occur in regards to bdev. spdk_bdev_open_ext
function uses bdev name as an argument instead of bdev
structure to remove race condition where user gets
the bdev structure and bdev is removed after getting
that structure and before open function is called.
spdk_bdev_open is now deprecated.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I44ebeb988bc6a2f441fc6a0c38a30668aad999ad
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455647
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Every exit path in spdk_bdev_set_qos_rate_limits() should
go through _spdk_bdev_set_qos_limit_done() as soon as
ctx is allocated and qos_mod_in_progress set to true.
This patch fixes one path were it did not occur.
With this change qos_mod_in_progress is set to false,
when failure in allocating qos parameters occurs.
Change-Id: I04a45dfdcde9160fd2701b44f5fde26fb0245177
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465659
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This is more accurate to what they are, and will make defining library
dependencies much simpler. This change in directory does not affect the
final placement of naming of libraries at the end of time.
Change-Id: Ic48a9233dff564e39ce357a9ea0a111ea2b6414b
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465454
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Only affects QAT where only partial data transfers would occur
when a host buffer crossed a 2MB boundary.
fixes issue #897
Change-Id: Ib20bfb3557c11a6da996f4b209e9bb7c634f8f49
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464719
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
The previous patch in this series introduced the notion of an
orphan comp bdev which is available only for deletion due to
a missing PMEM file. This RPC allows applications to list
orphaned comp bdevs as they will not show up with get_bdevs
because they are not registered bdevs.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I431f9cdebd4e5ae6068308639cb41d6c52f7309b
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465812
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
When a vol load fails because of a missing pmem file, instead of
doing nothing we now claim the underlying bdev and make an entry
in our global list for a comp bdev so that the regular delete
RPC can be used to delete the comp bdev.
fixes issue #890
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Icd5357060648e722f94e8f6b9038c8dad032feb3
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465807
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
So it can be called from an earlier one in the next patch.
Change-Id: I1e79669d33d84e54c27305e38076cbdafea627e3
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465986
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Will be re-used in an upcoming patch.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I676beb7f61c100043189c56484a41c209cd2942d
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465829
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
This is a part of a change that will introduce
new spdk_bdev_open_ext function. This will make
possible to pass callback function while opening
bdev which will be called when some bdev events
occur.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I3e552edd5c90dacd39885e75e9114e48dddf50ea
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463157
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
The arithmetic was backwards when computing the latency values to
report back to rpc calls like get_bdev. This caused reasonably sized
latency values to report back 0.
Change-Id: I85e22c9c8aa202a2ac1db7e7081f397800b151b8
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465168
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Part of a larger series unifying and simplifying the library directory
structure.
Change-Id: I2782165aabbea9a31cc466fc7e3bb2b9263142dc
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465211
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Because required alignment is already set to block size and by design
the crypto module does one crypto operation per block (it uses the
LBA as the initialization vector) it should not be possible to get
a physical address that spans however adding an assert just in case.
Change-Id: I1dc844d0a32395f9ed4869429368f60b919703a4
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465107
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This is patch that implements changes according to proposal
submitted in https://review.gerrithub.io/c/spdk/spdk/+/453036
Change-Id: I5423cd34cb5fc111b34cab2b7f7c6c5f11898af8
Signed-off-by: Pawel Kaminski <pawelx.kaminski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464677
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
WRITE_TO_RO_PAGE was incorrect and misleading. This
0x82 NVMe status code indicates a write to a read-only
range of LBAs. So modify the constant name and
associated usages to use WRITE_TO_RO_RANGE instead.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I993dbebb5acc2e685a0e99aa14084942ef79d659
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465083
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
This will allow us to do interesting things in tests like configure a
bdev with a really long delay, and allow I/O to build up on a target to
see what happens, then decrease the latency to allow traffic to flow
through normally without ever having to delete and reconfigure the bdev.
Change-Id: Ibcb1101f8eed9fe3094ba239110cb4e49ace6554
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464454
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Becomes important in next patch
Change-Id: Ida19f0b59c4b841d6f5120f9130e24b57ae91560
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464717
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Data type of number of base bdevs are corrupted. uint8_t is enough
and unify almost all related variables into uint8_t.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I323aaa229a76c3d5b5361d7643c3a9591ccad340
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464357
Reviewed-by: yidong0635 <dongx.yi@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Checking if required parameters strip_size, num_base_bdevs, and
raid_level had been done in raid_bdev_config_add(). However, this
required us to use integer type.
If we do the check in raid_bdev_parse_raid(), we will be able to
use the same type between function parameters and variables of
struct, and hence do in this patch.
This will align with the next patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I10fd75f25ed9a5d40eb189b05c2a20c276fa3ad6
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464365
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: yidong0635 <dongx.yi@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The following issue was observed.
The first thread returned the last IO channel and the second thread
then removed the first base device, but raid_bdev_cleanup() was
called before raid_bdev_destroy_cb() was called.
raid_bdev_destroy_cb() was accessed to the raid bdev already freed
by raid_bdev_cleanup() and caused segmentation fault.
The call sequence was as follows:
The first thread:
spdk_put_io_channel() -> ch->destroy_cb -> raid_bdev_destroy_cb
-> access raid bdev
The second thread:
raid_bdev_remove_base_devices() -> raid_bdev_deconfigure() ->
spdk_bdev_unregister() -> spdk_io_device_unregister() ->
spdk_bdev_destroy_cb() -> raid_bdev_destruct() -> raid_bdev_cleanup()
-> free raid bdev
The fix is to hold number of created channels in struct
raid_bdev_io_channel and use it in raid_bdev_destroy_cb().
Bdev layer, IO device/channel layer, and NVMe-oF layer already
process this case correctly.
Fixes#884.
Reported-by: yidong0635 <dongx.yi@intel.com>
Change-Id: Ie9d61bdddca479ce7f491ff9a08db45e71f16a8d
Signed-off-by: yidong0635 <dongx.yi@intel.com>
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463249
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
After recent changes, that function can not return
NULL anymore, so remove all redundant checks from
various SPDK libraries.
Change-Id: If80344b6fa81ad5f87a7086804dba221522cd7e2
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464175
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
spdk_jsonrpc_send_error_response() is documented as a
shorthand for spdk_jsonrpc_begin_result() + end result,
but we used to call it already after doing
spdk_jsonrpc_begin_result(), which makes the response
completely invalid.
Fix it by deferring the initial spdk_jsonrpc_begin_result()
until after we did our error checking. While here, remove
the NULL checks from that function. After recent jsonrpc
changes it can never return NULL.
Change-Id: Ibb69803d4e6ce6516817673eec6626dcfc4f1abf
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464174
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
'ResetControllerOnTimeout' was renamed to 'ActionOnTimeout' for a
long time, so we deprecate the support for this old configuration
option.
Change-Id: Ia44035a8749ca046c1df16f82601389b5bafeb76
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464491
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
SPDK_NVME_DEFAULT_RETRY_COUNT is the default value for each controller, so
we can move it out from public header file, and change the value if users
provide a new one.
"NvmeRetryCount" was deprecated for a long time, so we removed the support
for this configuration option as well.
Change-Id: I187251cc1e5342abb4fce96727d06631b7c16a01
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464489
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The lines in this file are extremely long. astyle doesn't
really allow us to always go under 100, but we can at least
try to do our best.
Change-Id: I36f454b67460cadf92f99578512349d048d4861b
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/462377
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Ran into this while putting the compress tests in CI, an error
message will print following the completion of the app, checked
with Jim and it is actually not an error when lvols are involved
so change to warn now as this will show up in everyone's build
log for bdev testing.
Change-Id: Ib509b89acf5b6bfbeb349692ab59bbea4964557f
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463803
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Will execute short run per patch, longer nightly. This
path only covers the ISAL PMD as there are QAT upgrades
needed in CI. It does so by using the new 'perform_tests'
RPC in both bdevio and bdevperf.
Change-Id: I93afda336d7411b695b2ddd0332cce0050d075a4
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455113
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Chunyang Hui <chunyang.hui@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
A single I/O may allocate more than one request, since splitting may be
necessary to conform to the device's maximum transfer size, PRP list
compatibility requirements, or driver-assisted striping. Very big
I/O request sent from application may get error due to limited resources
in NVMe driver layer, so here we add an optional parameter to make the
parameter can be configured by users.
Fix issue #745.
Change-Id: I7824232c54865b052dcd0ec6e91484c3837fc2c4
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/461182
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
For aarch64 spdk_mb is defined as "__asm volatile("dsb sy" ::: "memory")"
and spdk_smp_mb is defined as "__asm volatile("dmb ish" ::: "memory")".
"dsb sy" completes when all instructions before this instruction complete.
And "dmb ish" only keeps the order of memory access instructions before
and after it. It doesn't affect the ordering of any other instructions.
Here I think "dmb ish" is enough.
And replace spdk_mb with spdk_smp_mb here will not affect PPC64, X86_64
and i386.
Signed-off-by: Richael Zhuang <richael.zhuang@arm.com>
Change-Id: Idd65f74567c594e5a6514a4ab0665b8f3606c883
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463455
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Was 1024 but w/the performance optimizations we can now use up
to 4 mbufs per outstanding IO so going to 8192 only uses 1MB of
mem and gives us better head room before we have to start queueing
compression operations to wait for mbufs. Note: the mbuf pool is
shared accross all virtual compression bdevs.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I64d3973e7c7d31925b1ce5028ef960f90331c067
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463538
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
There's a small drive-by in here also, use the max iovec define
from the reduce header instead of manually making sure its the same
here.
The change in the size of the MBUF pool is to accommodate the new
QAT driver being faster (?) than the old such that we could run out
of MBUFS with a fio test using 6 threads. On the + side, when we did
the queueing code in the compression operation worked good.
Also related to QAT and experimenting with fio compression ratios, QAT
can fairly often return an error on compression that we were treating
as an error for printing, change it to a NOTCELOG instead of an error.
Change-Id: Id842064b7d659f7ad7f9d785ffffdc6b827f6989
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463369
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Old name was misleading due to earlier changes
Change-Id: Ic04223db983e98c9703a43e6778b0094f99bc81d
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463341
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
qpairs can be limited by the compression polled mode driver or
system resources and we need one per thread so if we run out we
have to fail the callback.
Change-Id: Ibd07d9c65880e7de321c439119aed479ef00746c
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463339
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
When connecting to an iscsi url that effectively does not exist we free
the data structures of the very context we are processing. This results in a
use after free and subsequently in a crash.
Signed-off-by: Jeffry Molanus <jeffry.molanus@gmail.com>
Change-Id: I67cab1efb161bfa23fa1022e150661080d90b556
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/462614
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Jeffry Molanus <Jeffry.molanus@gmail.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
If available, if not use the bdev unique name. This results in
a much friendlier comp_bdev naem for the user. For example,
now it would look something like this: COMP_lvs0/lvs as opposed
to like this COMP_0b149b31-b66b-4cf7-ab39-a55b50788cd1
Change-Id: I319a141221ed8880edcec930ca5be9f256b105e0
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463246
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Was previously creating the number of qp based on the # of cores
reported via DPDK function. Also was assigning one qp per comp_bdev.
After testing w/multiple threads in fio 2 things needed to change:
* remove use of rte core related functions as fio threads are not EAL
threads. This required choosing an upper limit for the number of
threads that the bdev module will support
* changing the qp assignment code such that comp_bdevs share the
same device_qp if on the same thread
Fixes issue #879
Change-Id: Ib968ee04bef63013616546341974a4431d8f266a
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463107
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Improve error messages where possible.
Also change return code values to negative in bdev_pmem.c so that
it follows the same pattern as other bdev modules.
Change-Id: I81b205a41104e15457154d1e31540210636ef9d3
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/461548
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Vitaliy Mysak <vitaliy.mysak@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Added parsing and saving of (optional) parameters which are responsible for
relocation in FTL. Changing the parameters may affect Write
Amplification Factor and overall performance, especially during random
write workloads. If parameters are not specified, default values will be used.
Signed-off-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Change-Id: Ic0229e39109460f3541c31e1cbf2a485efe408c6
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/460504
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
