This has changed to control the number of read buffers allocated to the
group, but it is only valid to set this register if the device has
indicated it supports it. Further, the default value is what we want
anyway, so we can skip setting it altogether.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Ic54672ea6cb16acc7613860e36d9f7033048bd98
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11484
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
All of the other structs and unions spell out register, so match the
style.
Change-Id: Ie502e80206305037d1518a1db590d89b7479abb4
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11433
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
SPDK can submit more commands to remote NVMf target than allowed by
negotiated queue size. SPDK submits up to SQSIZE commands, but only
SQSIZE-1 are allowed.
Here is a relevant quote from NVMe over Fabrics rev.1.1a ch.2.4.1
“Submission Queue Flow Control Negotiation”:
If SQ flow control is disabled, then the host should limit the number
of outstanding commands for a queue pair to be less than the size of
the Submission Queue. If the controller detects that the number of
outstanding commands for a queue pair is greater than or equal to the
size of the Submission Queue, then the controller shall:
a) stop processing commands and set the Controller Fatal
Status (CSTS.CFS) bit to ‘1’ (refer to section 10.5 in the NVMe Base
specification); and
b) terminate the NVMe Transport connection and end the association
between the host and the controller.
Signed-off-by: Evgeniy Kochetov <evgeniik@nvidia.com>
Change-Id: Ifbcf5d51911fc4ddcea1f7cde3135571648606f3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11413
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
According to NVMe over Fabrics specification (rev.1.1a) HSQSIZE sent
in RDMA_CM_REQUEST private data (ch.7.3.6.4) shall be the same as
SQSIZE later sent in Connect command (ch.3.3).
SPDK NVMe RDMA initiator adjusts SQSIZE to CRQSIZE received from
target in RDMA_CM_ACCEPT private data. Target is allowed to send
CRQSIZE < HSQSIZE if RNR retries are used. So, it is possible that
SQSIZE sent by SPDK will be lower than previously sent HSQSIZE. There
are targets validating this match and they reject connection from
SPDK.
Linux kernel NVMe initiator doesn't perform such adjustments and
connects well to such targets.
This patch aligns SPDK behavior with specification and Linux kernel
implementation.
Signed-off-by: Evgeniy Kochetov <evgeniik@nvidia.com>
Change-Id: I01968d1c07d284396fa5939932d85841351d7a45
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11350
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
There are errors occur that uninitialised value created by a stack allocation when running unittest_accel and unittest_nvme_rdma with valgrind.
Change-Id: I4b48b472cc7c189cbcaf8ca772830a23118e7e17
Signed-off-by: Jaylyn Ren <jaylyn.ren@arm.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10559
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
test/bdev/bdevperf/bdevperf.py invokes a process to perform test case
rather than processing RPC.
run_test_pid may be a better name than rpc_pid.
Besides, if the execution of the test hung up, try.txt is helpful to
investigate the cause. So print try.txt if the execution of the test
fails.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: Iab973f55dde2ef793fc0d3f1a36b3b59b168f579
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11400
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
it shall be executed on ctrlr's thread not subsystem's
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: I58c60525191085d3d6a583862ba5d71ea90940c7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11105
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
In many cases, addressing bdevs by their UUIDs is often easier than
using their names, which can be somewhat arbitrary. For instance, the
NVMe bdev builds a name by addng the n{NSID} suffix to the controller's
name, while the UUID is filled with NGUID (if available).
The UUID alias is stored in the form defined by RFC 4122, meaning five
groups of lower-case hexadecimal characters. It's important to note
that bdev layer uses case-sensitive name comparison, so the user needs
to use the same textual UUID representation.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I8b112fb81f29e952459d5f81d97fdc7a591730f8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11395
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
The script can now match UUIDs via the $(UUID) marker.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: Ied11f9ce65e4f1102309523f3f8ec0ee7c9e74d0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11410
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
spdk_nvme_cli_cuse.sh fails with:
```
NVMe status: DATA_XFER_ERROR:
Error while trying to transfer the data or metadata(0x2004)
```
when running test with v1.15 version. v1.16 works just fine.
Fixes#2361
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: Ic058d652d1a8f7adc05fefbad58a5e24d31f2cc8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11408
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reducing this value causes "nvme disconnect" operations
to return much quicker.
Without this change disconnecting from Kernel Target takes
about 40-50 seconds, from SPDK Target about 2 minutes.
Fixes#1748
Change-Id: Ib74d89735b4345cbeaf172190356e2c63f168fd0
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11309
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Monica Kenguva <monica.kenguva@intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
bdev_multi_allocation tries to write four characters, an integer between
0 and INT_MAX, and a nul byte into 10 characters. That requires at least
15 characters.
This leads to build failures with "make CONFIG_DEBUG=n CONFIG_UBSAN=y".
Change-Id: I8cb9fd4ede31ae24809e4a04fd60a67dae3a0ac4
Signed-off-by: Mike Gerdts <mgerdts@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11261
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
An spdk_bs_opts structure is sometimes partially initialized due to
using sizeof(opts) (struct spdk_blob_opts, 64 bytes) rather than
sizeof(bs_opts) (struct spdk_bs_opts, 72 bytes).
Signed-off-by: Mike Gerdts <mgerdts@nvidia.com>
Change-Id: Iaaa89bb419f66969d0888f49f8991c35b3dc5ea4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11268
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
While not documented as such, spdk_bdev_module_claim_bdev() has always
allowed a bdev that is opened read-only to remain read-only when
claimed. This occurs when NULL is passed in place of an spdk_bdev_desc.
This change updates the function's documentation to match the
implementation and adds a unit test to ensure the current behavior
remains.
Signed-off-by: Mike Gerdts <mgerdts@nvidia.com>
Change-Id: Ief26de60e4408bfe1aa60b7a4e1d8adf273470b6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11267
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Blob IDs are sequentially assigned starting at 0x100000000.
When debugging with a small number of blob IDs, it is much
more intuitive to see blob ID 0x100000000 rather than blob
ID 4294967296. If blob IDs are displayed in hex, the things
that parse commands should also accept hex to facilitate
copy and paste.
Signed-off-by: Mike Gerdts <mgerdts@nvidia.com>
Change-Id: Ic71eaaf1987609b4f705d372ced4240650b12684
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11245
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
To allow SO_MINOR updates on LTS for the whole year it is supported,
the major version for all components needs to be increased.
This is to prevent scenario where two versions exists with matching
versions, but conflicting ABI.
Ex. Next SPDK release adds an API call increasing the minor version,
then LTS needs just a subset of those additions.
Increasing major so version after LTS, allows the future releases
to update versions as needed. Yet allowing LTS to increase minor
version separately.
Disabled test for increasing SO version without ABI change, as
that is goal of this patch. This check shall be removed with SPDK 22.05
release.
This patch:
- increases SO_VER by 1 for all components
- resets SO_MINOR to 0 for all components
- removes suppressions for ABI tests
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Id1a5358882dc496faa5b0b5c9a63b326c378c551
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11361
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
When an unexpected xattr name is passed to lvol_get_xattr_value(), no
error is returned to the caller. The one caller, blob_set_xattrs() via
the xattrs->get_value callback, makes the reasonable assumption that a
lookup that fails to find a value returns a NULL value. This updates
lvol_get_xattr_value() to match that expectation.
Signed-off-by: Mike Gerdts <mgerdts@nvidia.com>
Change-Id: I5c7a740f2757e6d8265ba2637afecb729acfcdd4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11326
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
VFIO in QEMU uses region 9 as the PCI passthrough devices' migration channel.
The format of the region 9 migration region is as follows:
------------------------------------------------------------------
|vfio_device_migration_info| data section |
------------------------------------------------------------------
QEMU will access vfio_device_migration_info to controll the migration
process.
For SPDK vfio-user target, we also implement the BAR9 via libvfio-user,
and we also define the NVMe device specific migration data stored in
data section of BAR9. QEMU doesn't care about the format in data section,
it will help us to gather the NVMe specific migration data in source VM and
then restore the migration date to data section of BAR9 in destination VM.
The core idea to implement live migration will following the device state
change which is controlled by QEMU. First QEMU will try to STOP the device
in the source VM, and set the destination VM to RESUME state, SPDK will save
NVMe devic state data structure to BAR9 in the source VM once the subsystem
is paused, then QEMU will read BAR9 in source VM and restore the content of
BAR9 in destination VM, finally in the destination VM, we will restore the
NVMe device state include BARs/PCI CFG/queue pairs in the destination VM.
Change-Id: I42e38f28c3ff59831be63290038b50d199d06658
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7617
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Thanos Makatos <thanos.makatos@nutanix.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch aligns namespace comparison with Linux kernel
implementation:
- UUID is optional and may be NULL
- command set (CSI) should be the same
Signed-off-by: Evgeniy Kochetov <evgeniik@nvidia.com>
Change-Id: I8f889989f24cd51b104057217f87eb303b30fa68
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11312
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
To compile contigmem and nic_uio in DPDK the `enable_kmods`
flag has to be enabled in meson. This is required for FreeBSD.
This is done in dpdkbuild/Makefile for the submodule,
but is needed in build_native_dpdk() for upstream DPDK tests.
While here, removed comment in autotest_common.sh that refered
to patch that was already upstreamed to DPDK. See:
https://review.spdk.io/gerrit/c/spdk/dpdk/+/2534
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I2ee17ed5b62291881e64b687c642a81993e03e36
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11238
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Michal Berger <michallinuxstuff@gmail.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
For correct behaviour, pthread_mutex must be initialized before use
and destroyed afterwards. An already initialized mutex should not
be re-initialized.
Add calls to nvme_ctrlr_construct where nvme_ctrlr_destruct is
called without a matching construct.
Add missing calls to mutex_init and mutex_destroy as required.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I9753fa7fbd77402f23a08a66f4b489a5c229487a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11298
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Community-CI: Mellanox Build Bot
Apply https://review.spdk.io/gerrit/c/spdk/dpdk/+/11139 patch
to accomadate QAT SYM and ASYM VFs when running crypto
functional tests.
This replaces DPDK v21.08 patches, as v21.08 is no longer
supported.
Change-Id: Ic11de9de1f96288f6b2ff504a1d262e41ad66063
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11204
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
SPDK test script can fail during any point of the
execution. To keep using the same devices
between test runs in CI, those devices have to
be cleaned between runs.
To select device for tests or to clean before tests,
the partition table and lack of mount points is used.
SPDK GPT partitions were always considered not in use.
Meanwhile Linux GPT were not, even if lacking a mount
point.
Some of the SPDK tests create Linux GPT partitions,
which might remain after a test run.
Linux GPT partitions created during tests now contain
"SPDK_TEST" as part of their partition name.
This allows marking such block devices as 'not in use',
to be cleaned and used in further SPDK test.
fixes#2345
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I0098776239da9b0c5dcc748625485284e4863525
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11220
Reviewed-by: Michal Berger <michallinuxstuff@gmail.com>
Reviewed-by: Dong Yi <dongx.yi@intel.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The common file is sourced in all test scripts, so it
is ideal place to put all library paths.
It will make changes to those paths simpler in next patch.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ic37148e6be669f296e8561d6554e735132941413
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6685
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This reverts commit eb09178a59.
Reason for revert:
This caused a degradation for adminq.
For adminq, ctrlr_delete_io_qpair() is not called until ctrlr is destructed.
So necessary delete operations are not done for adminq.
Reverting the patch is practical for now.
Change-Id: Ib55ff81dfe97ee1e2c83876912e851c61f20e354
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10878
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Fix issue: #2320
Only the primary process will do the unmap bar operation as for
the map bar operation.
The DevHandle is process specific and the issue here is the
secondary process's function pointer of DevHandle is not properly
set.
Change-Id: I95dddc76c6ce4be8775b6aaf54699002baffd3b9
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11216
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Found via inspection during spec review of latest HW. We were using the
wrong stride for the WQCFG regsiter when configuring but it just so
happened to be the right value for the current DSA version. We were
mixing up the size of the WQCFG register with the stride value used to
configure the next WQCFG regsiter as they are not contiguous in HW, we
need to read another capabilities bit to determine the address of the
next wqcfg to configure..
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I14d1ff95e0131fd30121aa955bfbc8c8fb3fc512
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10968
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Compliant with both current and next gen DSA.
Note: some fields in gencap were mapped incorrectly
previously, but this did not impact the SPDK driver
because the only times those values (max_xfer_shift
and max_batch_shift) were used were in asserts.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I9648184670f661166136e7898d0d8c7e07d8c746
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10966
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Creation of sockets is specific to rte_vhost, so it
functionality responsible for setting path for them.
dev_dirname is renamed to g_vhost_user_dev_dirname
and its definition is moved to rte_vhost_user.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I9bae67667b0f6624f2daf3244a048d10e94e553c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10631
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
vhost.c contains a lot of functionality that
is rte_vhost specific. This series is moving
rte_vhost specific functionality to rte_vhost_user.c.
UT for vhost didn't make a distinction for either.
So starting with this patch the rte_vhost_user.c
is now included in the UT, only stubing out rte_vhost functions.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I0d5f62ad47d1261bbb44c0aa23400d94ece4564e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10743
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
From SAM-4, section 5.13 (Sense Data);
“When a command terminates with a CHECK CONDITION status, sense data shall be returned
in the same I_T_L_Q nexus transaction (see 3.1.50) as the CHECK CONDITION status. After
the sense data is returned, it shall be cleared except when it is associated with a unit
attention condition and the UA_INTLCK_CTRL field in the Control mode page (see SPC-4)
contains 10b or 11b.”
SPDK does not set UA_INTLCK_CTRL to 10b or 11b, so we set the unit attention condition
immediately against a single IO or Admin IO after reporting it via a CHECK CONDITION.
Once the failed IO received at iSCSI initiator side, it will be retried. In the case of
resize operation, if there is no IO from iSCSI initiator side, the unit attention
condition will be delayed to report until the first IO is received at the iSCSI target
side.
Meanwhile, we clear the resizing (newly added) flag on our SCSI LUN structure after
first time we report the resize unit attention condition.
The kernel initiator won’t actually resize the corresponding block device automatically.
It will report a uevent, and then you can set up udev rules to trigger a rescan. SPDK
iSCSI initiator will automatically report the LUN size change.
Change-Id: Ifc85b8d4d3fbea13e76fb5d1faf1ac6c8f662e6c
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11086
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Enable vfio_user mode to be able to test VFIO transport
using the exact same steps as we do for Vhost target.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I482fae29f3b67bedff00f9853d93c5772b0ee447
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6702
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Skip this option when using different target
(i.e. nvmf_tgt for vfio-user tests) as it might
be unsupported.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I9bc0677a6142039a1531255ca974059ee29cf705
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11015
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Increase the batch size and with it the effective queue depth per
channel to 512.
Change-Id: Ide665e92d47ee753c141f34dd6a8bc4d040fe8db
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11031
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: John Kariuki <John.K.Kariuki@intel.com>
SPDK RDMA target reports msdbd=16, these addtitional
SGL descriptors are located in capsule. The user can
set ICD size lower than required for msdbd=16. This
patch verifies that ICD can hold all additional SGLs.
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I875d40e14e6506c39169d084e56df7ca5d761209
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10686
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
We will assign each SQ with different poll group in round
robin way by default, this may cause race condition to
post completions to one CQ in different threads, so here
we will assign the SQs which share one CQ into same poll
group.
Also enable multiple cores NVMe compliance tests so that
to cover shared IO CQ case.
Change-Id: I9d7cc78aaedceed23986d9f89ed945e0eb337e09
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11115
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
libvfio-user will call quiesce callback when there are
memory region add/remove and device state change requests
from client, and in the quiesce callback, we will pause
the subsystem so that it's safe to do everything after
it, then after quiesce callback, we will resume the
subsystem. The quiesce callback is also used in
live migration, each device state change will quiesce
the device first.
Change-Id: I3a6a0320ad76c6b2d1d65c754b9f79cce5c9c683
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10620
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Admin commands can be sent and polled from any thread, which also means
that the error injection queue on the admin qpair can be accessed from
multiple threads. Therefore, any modifications to that queue should be
done under the ctrlr lock.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: Ib1ed194405cb5b93f65a007b9749fd4433dc367d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11099
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
There is an error case that the block device didn't complete
outstanding IOs during the controller reset or shutdown, so
the NVMf library will wait until all the IOs returned from
the backend, however, so here we added a timeout timer, when
the time expired, we will try to reset the block device which
hold the outstanding IOs.
Fix#2194.
Change-Id: I8d0746335e1f20a09e6a9ea87730551808a898d1
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9909
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Dong Yi <dongx.yi@intel.com>
Fix warning: missing braces around initializer
This issue is seen with gcc (GCC) 4.8.5 20150623.
Warning like below:
nvme_tcp_ut.c:243:9: warning: (near initialization for ‘ctrlr.ns’) [-Wmissing-braces]
nvme_tcp_ut.c: In function ‘test_nvme_tcp_req_init’:
nvme_tcp_ut.c:525:9: warning: missing braces around initializer [-Wmissing-braces]
struct spdk_nvme_ctrlr ctrlr = {0};
^
nvme_tcp_ut.c:525:9: warning: (near initialization for ‘ctrlr.ns’) [-Wmissing-braces]
And more information from below link:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=53119
Change-Id: I88b5b3908d5d0daa9383e47a1ed53288f342ca3b
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11137
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
This is the same effort as the last patch.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: I94ef08abdbb2bd2e07d0cd1e552c5d05c805233e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10817
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
More precise stubs for spdk_nvme_poll_group are critically important
to verify upcoming changes.
Add a flag is_failed to struct spdk_nvme_qpair separately from
is_connected. This is used to inject error to a connection.
Replace a single list qpairs by two lists, connected_qpairs and
disconnected_qpairs for struct spdk_nvme_poll_group.
Then utilize these to manage qpair in poll group.
spdk_nvme_ctrlr_reconnect_io_qpair() is not used in the NVMe bdev
module now. Remove the corresponding stub.
Adjust polling count accordingly.
Change-Id: I4d867c56ae518276813f6f96d23a5f6933364fd4
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10816
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
nvme_poll_group_disconnect_qpair() is called only by a single place now.
We do not need the flag poll_group_disconnect_in_progress any more.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: I8f9c0f14baa8fcb9b0637635a5bb3d34a8b11af5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10673
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
