At this time all iSCSI tests were using local address
127.0.0.1 for both sides of connection.
This patch changes iSCSI tests to use separate
veth (virtual ethernet) interfaces.
It will allow to actually verify functionality when using
different target and initiator IPs.
Veth are used as most closely resembling real enviroment
in single host and without any network hardware required.
This patch serves as a base for future VPP test changes,
where veth interfaces are used as well.
Note: Netmask changed to /30 temporarily and
verify_iscsi_connection_rpc_methods in rpc_config disabled.
Kernel will route trafic between two veth interfaces through
host stack. This causes target and initiator IPs
to be not as expected. Those are changed back in next patch
by adding namespaces.
Change-Id: Ida8fce107e8262bef94b2161e0197c45f6e3f070
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405552
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This will allow us to run vm setup multiple times on a vm without it
failing due to pre-existing directories.
Change-Id: Ied17dd40daaa4b5f9a1e2448940d413c7db7cc96
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/405508
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
This patch adds compilation and installation of VPP.
Note that it removes one of VPP config files, that is
responsible for setting up hugepages. It is already done
with setup.sh script.
Parameters kernel.shmmax and vm.max_map_count were set
to low count and causing issues with hugepage total sizes
above 1GB.
Change-Id: Ic6c31f4192c654672e36c4131e34eb5b8aaac022
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/404144
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Seth Howell <seth.howell5141@gmail.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Refactoring the existing AER test code which add an option
to enable temperature tests of AER, this will enable coming
patch which add Namespace attribute notice tests support.
Change-Id: I514a1d6d0d3aacf4e207fb437406b5cf048f2a71
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/406026
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
This addresses a large number of Klocwork issues.
Change-Id: I911960b12f8b62ebf54901c62f34f3b2064e5f61
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/406857
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
NVML (Non Volatile Memory Library) changed its name to
PMDK (Persistent Memory Development Kit), so make the
necessary changes to the SPDK repository.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Id07a87eafb4e9a3099603030c58c0e927bafa608
Reviewed-on: https://review.gerrithub.io/406256
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
netstat is deprecated on CentOS/RHEL in favor of
iproute utilities. At least on one of the systems
in our test pool, netstat isn't installed - we could
install it but let's instead try to use ss if it's
available and still fall back to netstat when it's
not.
While here, remove waitforlisten_tcp instead of
changing it to use ss. We are not using waitforlisten_tcp
anywhere and do not recommend enabling RPC over TCP except
for test purposes.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I4ee3597536797f501750915a4a219b55004bd454
Reviewed-on: https://review.gerrithub.io/406464
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Run identify against the subsystem we configured earlier, in addition to
the discovery subsystem. This mirrors the behaivor of
test/nvmf/host/identify.sh.
Change-Id: Ia96c46adb427239f0306d3b57588ee14742b968d
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/406638
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This commit moves the name verification function out of the
spdk_lvol_create.
Also changes return value from -EINVAL to -EEXIST when name
already exists in lvol store, as more informative. It implies
that spdk_lvol_create also returns -EEXIST error code for
this case.
Change-Id: Ie0f642b316ba8c5cc42657334d35e539be56e830
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Reviewed-on: https://review.gerrithub.io/406745
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Signed-off-by: Piotr Pelplinski <piotr.pelplinski@intel.com>
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Change-Id: Iad67be79d0ddd8c498950c4f7b1b3203e47a7a41
Reviewed-on: https://review.gerrithub.io/393936
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch adds new feature of blobstore.
New call creates a read-only snapshot of specified blob with provided options.
NOTE:
This patch doesn't cover recovery operation if snapshotting fails. This operation
will be implemented and added later.
Signed-off-by: Piotr Pelplinski <piotr.pelplinski@intel.com>
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Change-Id: I470ca13525638fa6df485d508b3adf71b6b69c0b
Reviewed-on: https://review.gerrithub.io/393935
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch changes hardcoded value for target IP to one from
common.sh.
Config file here should be replaced with RPC in the future.
Change-Id: I24ef413fcb9369a74b1db182338b5b41e0874a55
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/406364
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Make sure test case 10000 is always last, since it kills the target app
and makes any tests run after it fail.
This also de-duplicates the test execution code (now the "all" case
just fills out tc_list).
Change-Id: I88b629a1ef17afd4b95a4fd7d0cbf0321238b7a4
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/406677
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
To support resize operations during I/O, we will need
to send messages to each thread to quiesce I/O while
the resize operation is in progress to guard against
the cluster map memory changing while another thread
is accessing the cluster map.
Therefore, spdk_blob_resize needs to be asynchronous.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ida037334739b4b80a1dbc76e8f1c70bca8b73582
Reviewed-on: https://review.gerrithub.io/404616
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Don't allow the user to specify an invalid ASCII string for the
controller serial number field.
Change-Id: I1c3acf6997a0afcdbfc03caf9e8d9b5fab429106
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/406441
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
SPDK_NOTICELOG should only be used for significant but non-warning/error
messages, such as notifications of deprecated config file sections.
Change-Id: I885dfe839c9cbc9eceabee234e4d0eb74c6910df
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/405923
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Dariusz Stojaczyk <dariuszx.stojaczyk@intel.com>
Reviewed-by: Pawel Wodkowski <pawelx.wodkowski@intel.com>
This unit test operated under the assumption that one could immediately
free a bdev after calling spdk_bdev_unregister. This assumption is
broken when we moved the actual destroy call to an asynchronous callback
to spdk_io_device_unregister.
Change-Id: I92d34f7e2e2993bfe9391f9bb72e08128dec74f4
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/406429
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This thread is needed in any context when we send a message.
Change-Id: Ifcb5e3bf2e6ee60385b425a976ed380228570ae6
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/406427
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
No code change - the existing code is moved as-is.
This is the only place it is used, and it is conceptually part of the
virtual controller implementation.
Change-Id: I863f5931225c4d78e515341445e91b29a73da64d
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/406251
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Several intermittent test failures have been seen with recent
changes to this test. Disabling it for now while the issue
is debugged further.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I0634f182dab3d3d259690981474866a2037c7fce
Reviewed-on: https://review.gerrithub.io/406454
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
For application like vhost/iSCSI target/NVMe-oF target/etc,
a new section as below can be added for the QoS rate limiting.
[QoS]
Limit_IOPS Malloc0 100000
Limit_IOPS Nvme0n1 500000
Also added a sample change at test/lib/bdev/bdev.conf.in
Change-Id: I7c7d951fbe1352ca2571f135c657bc4fa43b56c7
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.gerrithub.io/393221
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
As there is no I/O channel associated with the QoS
bdev channel, add the specific functions to handle
the reset operation on the QoS bdev channel. The
reset operation will be conducted on the QoS thread.
Related UT code on QoS with reset operation was also
included.
Change-Id: Ibba68ddb132fa926fec6327829157b43ac806713
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.gerrithub.io/393181
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This enables virtio tests to run with 2MB hugepages
Change-Id: I0f9e2de0cb1f68fb967b929d8a27c6e410cb675a
Signed-off-by: Dariusz Stojaczyk <dariuszx.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/404318
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Add iscsi filesystem test cases(run fio) with
lvol and nvme backend in nightly.
Change-Id: I822e5c570fb9ef96ce63bf1c853c537b35c8b1d7
Signed-off-by: xuhuagen <huagenx.xu@intel.com>
Reviewed-on: https://review.gerrithub.io/405513
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Users can use RPC to add/remove a namespace to/from
existing NVMe controller, SPDK NVMeoF target will
generate an asynchronous event as an indication to
host when asynchronous event request is available.
While here, we also set the event with invalid log
identifier, so that the host doesn't need to clear
the event. Users can use Set Feature to disable
such event.
Change-Id: I93c4d752f552d3c86c53e80877aa61c093e167cc
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/398759
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Similar with exist vhost scsi/blk target, this commit introduces
a new target: vhost nvme I/O slave target, QEMU will present an
emulated NVMe controller to VM, the SPDK I/O slave target will
process the I/Os sent from Guest VM.
Users can follow the example configuation file to evaluate this
feature, refer to etc/spdk/vhost.conf.in [VhostNvme].
Change-Id: Ia2a8a3f719573f3268177234812bd28ed0082d5c
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/384213
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This has been replaced with a pmem component-level test.
Change-Id: I3c433d9edbb4c4f0ff26d7716cd11ee9df5c0ad7
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/405910
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
The long-term plan is to use the JSON-based configuration format, but
for now, we need a config file section to be able to test a bdev module
in blockdev.sh.
Change-Id: I2a69f7172693ed6d4939a3b938747e2a1c62ff83
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/405908
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
In function verify_iscsi_connection_rpc_methods fixed
initiator address verification. It was used addres for target. From now
it is used separate addres for initiator.
Change-Id: I46ee7ab758b24342b6a25553a62a517914e9b70e
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Reviewed-on: https://review.gerrithub.io/405582
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Target IP for Calsoft tests was hardcoded in config file.
Now it will be based on iSCSI tests common configuration.
Change-Id: Ic8db40b02d2be59f5fac5cb4503cc0c80b24cd91
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405865
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
- Add support for multi page CNS 0x2
- Use CNS value 0x02 (SPDK_NVME_IDENTIFY_ACTIVE_NS_LIST)
to query active namespaces
- Add an API to iterate the active list
Change-Id: Iea524881fa6e3610a7d85ab02a2005a92fd633df
Signed-off-by: John Meneghini <johnm@netapp.com>
Reviewed-on: https://review.gerrithub.io/401957
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
unlike previous implementations of ceph, luminous (which ships with
fedora 27) does not create a default pool for us. In case we are on a
system using luminous, we need to create that pool ourselves.
Change-Id: I183dc4fff6b92f7b270bd5a5d05947f0d99e9d04
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/405703
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
There are timeouts in NIGHTLY_TEST mainly caused by long duration
of spdk_vhost.sh --fs-integrity-blk test. It could be shorten by
reducing file size in fio test
Change-Id: Ic99f6f3ce52ed8bf1fafc75bb0f908d9df0d0d4e
Signed-off-by: Pawel Niedzwiecki <pawelx.niedzwiecki@intel.com>
Reviewed-on: https://review.gerrithub.io/405587
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This problem was discovered after an lpfc card was installed
in one of our CIT tetbeds. When an lpfc card is installed the
modprobe call in identify_kernel_nvmf.sh will load lpfc
as a side effect of loading nvmet. When this happens, you
can't unload nvmet until lpfc is unloaded.
Change-Id: I2cf63ea7d20b7dc15d73c7a8c8502fb05bef29f8
Signed-off-by: John Meneghini <johnm@netapp.com>
Reviewed-on: https://review.gerrithub.io/405518
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Test pool (and personal observatian VM launched by hand) show that VM
boot and shutdwon time can vary a lot. It would be good to make this
time more predictable but till then increase the shutdown timeout to 30s
in hope this will solve random shutdown timeout issue.
Change-Id: Icd23dc512aaf91bff47740308929ec4057c69469
Signed-off-by: Pawel Wodkowski <pawelx.wodkowski@intel.com>
Reviewed-on: https://review.gerrithub.io/405885
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
SPKD base bdev might be part of multiple vbdevs. The same is true in
reverse direction. So consider folowing scenario:
bdev3 bdev4 bdev5
| | |
+-+--+ + +--+--+
/ \ | / \
bdev0 bdev1 bdev2
In current implementation bdev0/1/2 will apear as base base for
bdev3/4/5 which is obviously wrong.
This patch try to address this issue.
Change-Id: Ic99c13c8656ceb597aba7e41ccb2fa8090b4f13b
Signed-off-by: Pawel Wodkowski <pawelx.wodkowski@intel.com>
Reviewed-on: https://review.gerrithub.io/405104
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Dariusz Stojaczyk <dariuszx.stojaczyk@intel.com>
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Change-Id: Ia536d956c7393c244afc29d44196207ac73f48be
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405545
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I58b53634fea07db219b20ee5b74cf31e708279a1
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405548
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This moves all iSCSI configuration to common.sh that
should be sourced in each test file.
When particular tests requires different configuration,
it can overwrite those values.
(See ip_migration.sh)
Change-Id: Ia5f684142fb910184809ee7efe74b5a51063b374
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405547
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This makes it clear and common among all iSCSI scripts
what ISCSI_PORT is refers to.
Change-Id: I01924179fb304b9cd111c39ff1b07aa3427d2c0c
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405544
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Previously values for iSCSI configuration were hardcoded
within the rpc_config script. Now it takes arguments
from bash script above.
This is base for making iSCSI configuration
common among all test scripts.
Change-Id: I1fecdd87bc11fe053590a4e25c9020cb9085eb30
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405543
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
add_initiator_group accepts netmask in IP/MASK format
and that should be sufficient for the current rpc_config tests.
This is base for future change to parametrize arguments
in this script.
Change-Id: I53346ec7af11c3266acc3d186a81b5948f7f2919
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/405542
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
