Found via inspection during spec review of latest HW. We were using the
wrong stride for the WQCFG regsiter when configuring but it just so
happened to be the right value for the current DSA version. We were
mixing up the size of the WQCFG register with the stride value used to
configure the next WQCFG regsiter as they are not contiguous in HW, we
need to read another capabilities bit to determine the address of the
next wqcfg to configure..
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I14d1ff95e0131fd30121aa955bfbc8c8fb3fc512
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10968
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Compliant with both current and next gen DSA.
Note: some fields in gencap were mapped incorrectly
previously, but this did not impact the SPDK driver
because the only times those values (max_xfer_shift
and max_batch_shift) were used were in asserts.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I9648184670f661166136e7898d0d8c7e07d8c746
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10966
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
From SAM-4, section 5.13 (Sense Data);
“When a command terminates with a CHECK CONDITION status, sense data shall be returned
in the same I_T_L_Q nexus transaction (see 3.1.50) as the CHECK CONDITION status. After
the sense data is returned, it shall be cleared except when it is associated with a unit
attention condition and the UA_INTLCK_CTRL field in the Control mode page (see SPC-4)
contains 10b or 11b.”
SPDK does not set UA_INTLCK_CTRL to 10b or 11b, so we set the unit attention condition
immediately against a single IO or Admin IO after reporting it via a CHECK CONDITION.
Once the failed IO received at iSCSI initiator side, it will be retried. In the case of
resize operation, if there is no IO from iSCSI initiator side, the unit attention
condition will be delayed to report until the first IO is received at the iSCSI target
side.
Meanwhile, we clear the resizing (newly added) flag on our SCSI LUN structure after
first time we report the resize unit attention condition.
The kernel initiator won’t actually resize the corresponding block device automatically.
It will report a uevent, and then you can set up udev rules to trigger a rescan. SPDK
iSCSI initiator will automatically report the LUN size change.
Change-Id: Ifc85b8d4d3fbea13e76fb5d1faf1ac6c8f662e6c
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11086
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
This is no longer needed.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I11b7e9acbcf1239a0ad2f49169d7e3d5844a1b93
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11029
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Add/modify tpoints around io_device name in lib/bdev/bdev.c
and lib/thread/thread.c.
Deleted double spaces in commets of trace_defs.h.
Change-Id: I0e2f5118e68b1b329a422bde3400fd2273e7387e
Signed-off-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10687
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
We can do all of the configuration in spdk_idxd_get_channel, and the
configuration step was always done immediately after getting the channel
anyway.
Change-Id: I9fef342e393261f0db6308cd5be4f49720420aa0
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10349
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Monica Kenguva <monica.kenguva@intel.com>
The driver still may use batches to implement some operations or for
efficiency reasons.
Batching my be resurrected in the future, but for now we need to do some
fairly extensive performance changes on the driver and eliminating all
of this unused/inactive code makes that much easier.
Change-Id: I92fcec9e4c7424771f053123d821cc57dba9793c
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10348
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
This change introduces initial experimental wrappers for enabling/
disabling rte_pci_device interrupts and for getting event file
descriptor assosiated with an interrupt.
Signed-off-by: Maciej Szulik <maciej.szulik@intel.com>
Change-Id: Iba1ba1e57a3555001502859d0bb2c655c07bf956
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10502
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jacek Kalwas <jacek.kalwas@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Chaining may be faster, but this is really an implementation detail of
the idxd driver. Push the decision on how to implement a vectored crc
down into the individual drivers and eliminate it from the generic
framework.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Iedbdc5a6dbd3f7d1674d0a83f6827588f4b6b2fb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10291
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
This uses a batch with the fence flag for now. There are several other
implementation options that will be explored in the future.
Change-Id: I4f344d671400508de05f80b026d42f775c5b9588
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10289
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Compare two scattered memory regions
Change-Id: I6ce5c9e7bc1ee1ef0e9173c00e86628d43a1e41f
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10287
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Since spdk_bdev_zcopy_end() cannot really fail (it only fails if we pass
a bad bdev_io), we can simplify the nvmf zcopy_end functions by making
them void and always expect asynchronous completion.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I6e88ac28aba13acadea88489ac0dd20d1f52f999
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10790
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Since this path now supports sending zero-copy, use it for zcopy_start.
Additionally, it makes it possible make zcopy_start void, as it reports all errors
asynchronously via request_complete(), and remove some of the duplicated
error checks.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I41f43ce1651432d9a7d74e3680d4a3f780128a1d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10789
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
It's more descriptive that way, as it's clear the function works on a
single request. Also, passing a request instead of zcopy_phase makes it
more convient to use.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: If4d7b087511e128f3590ac7b3b5adcb8ace12003
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10781
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Dong Yi <dongx.yi@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
It makes it possible for the user to specify whether a transport should
try to use zero-copy to execute requests when possible.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I40a92b0d7a6707f4c9292795f380846acb227200
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10780
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Make trace_create_tpoint_group_mask() an external function.
This is going to be used in following patch.
Change-Id: I06cd1652bb30abddd49536bc76ec134a01121537
Signed-off-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10830
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
These definitions will be used in the next patch to check if
device is rxe
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: Icc073344103991ff24fc3bb88a1ceb9867de6f6a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10727
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Currently if we remove a listener from a subsystem, we
disconnect *all* qpairs that have the same transport ID
as the listener being removed.
Fix that, since we should only disconnect qpairs from
controllers associated with the subsystem that had the
listener removed.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I6cf7422d14f23bf02ba6c4b034b172870694b3e6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10690
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This API is a helper for getting the full discovery
log page from a discovery controller. It will read the
log page header to get the total number of entries,
allocate a buffer for all of the entries, and then
issue a series of get_log_page commands to read each
4KiB worth of entries.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I02666ef5adcb9fc8825a221655811ace708f97b8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10564
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
so the functions declared in this header file are not mangled by
the C++ compiler when building, for instance, a bdev driver, implemented
in C++.
Signed-off-by: Kefu Chai <tchaikov@gmail.com>
Change-Id: I5a5d1abb06d0d3cd5f5d9245bb7c080f3874e83b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10745
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
This patch will fix the following c++ warning, if
SPDK_LOG_REGISTER_COMPONENT is used in c++ projects.
designator order for field ‘spdk_log_flag::name’ does not match declaration order in ‘spdk_log_flag’
Signed-off-by: Liu Qing <winglq@gmail.com>
Change-Id: I2a709bc78d8e4329055c2cd83cddddae01fb0fa1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10697
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
spdk_ioviter_next will walk through two iovecs and yield pointers
to common length segments. For example, given a source iovec (siov) with
4 1KiB elements and a destination iovec (diov) with 1 4KiB element, the
following will happen:
first spdk_ioviter_next:
src = siov[0].iov_base
dst = diov[0].iov_base
len = 1KiB
second spdk_ioviter_next:
src = siov[1].iov_base
dst = diov[0].iov_base + 1KiB
len = 1KiB
third spdk_ioviter_next:
src = siov[2].iov_base
dst = diov[0].iov_base + 2KiB
len = 1KiB
fourth spdk_ioviter_next:
src = siov[3].iov_base
dst = diov[0].iov_base + 3KiB
len = 1KiB
fifth spdk_ioviter_next:
len = 0
This is a useful utility for performing operations where both the source
and destination are scattered memory. As an example and a test vehicle,
spdk_iovcpy has been updated to use this internally.
Change-Id: I7e35e76d38e78d07ea1caf6282d0dfc02182aa83
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10284
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
it is possible that some specific transport doesn't support
NVMF_MAX_ASYNC_EVENTS (although it is a recommended value by spec)
with that change it is possible to reduce aerl on transport specific
layer so it can be advertised correctly during identify controller
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: Ife6465b5324fb39f9b343c6f42b860e9dd1164b2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10422
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Not every transport requires accept poller - transport specific
layer can have its own policy and way of handling new connection.
APIs to notify generic layer are already in place
- spdk_nvmf_poll_group_add
- spdk_nvmf_tgt_new_qpair
Having accept poller removed should simplify interrupt mode impl
in transport specific layer.
Fixes issue #1876
Change-Id: Ia6cac0c2da67a298e88956734c50fb6e6b7521f1
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7268
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
On aarch64 platforms, doorbells update from guest VM may not be seen
on SPDK target side. This is because there is memory type mismatch
situation here. That is on guest VM side, the doorbells are treated as
device memory while on SPDK target side, it is treated as normal
memory. And this situation cause problem on ARM platform.
Refer to "https://developer.arm.com/documentation/102376/0100/
Memory-aliasing-and-mismatched-memory-types". Only using spdk_mb()
cannot fix this. Use "dc civac" to invalidate cache may solve this.
Profiling data did not show big performance degradataion.
Signed-off-by: Rui Chang <rui.chang@arm.com>
Change-Id: I9a18718f8c4307b3007b18c32ab02e6796548958
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10222
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
This function serializes a buffer as a hex string.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I09ab93bc626f6f6543b7c1ef033bcf807050862a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10651
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Community-CI: Mellanox Build Bot
These APIs are not safe, since they do not hold the
pci device lock across calls, which can cause problems
if a device is inserted or removed while handles
returned by these APIs are being used.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I01a80f26d0a0ca4cdfc7181359932b38da8dd43a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10659
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
This is a safer alternative to spdk_pci_get_first/next_device,
since those APIs do not hold the lock between calls.
Future patches will remove those APIs, and change callers to
use this new API instead.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I71c7e8c1feb9112da8be32a8056b30e105e30463
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10655
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Batching will be made available for DSA specifically through the new
idxd_perf tool.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ic51d9ad3692074805b1ffa705cea8be35737c778
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9846
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Monica Kenguva <monica.kenguva@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The NVMe bdev module will support two features, delayed reconnect and
delete after multiple failures of reconnect to improve error recovery.
The recently added two APIs, spdk_nvme_ctrlr_reset_async() and
spdk_nvme_ctrlr_reset_poll_async(), were not good enough.
spdk_nvme_ctrlr_reset_ctx was not necessary. It had only a pointer to ctrlr.
Using a pointer to ctrlr directly saves us from undesirable malloc error
processing.
Separate spdk_nvme_ctrlr_reset_async() into spdk_nvme_ctrlr_disconnect()
and spdk_nvme_ctrlr_reconnect_async(). spdk_nvme_ctrlr_disconnect()
disconnects ctrlr including disconnecting adminq.
spdk_nvme_ctrlr_reconnect_async() moves the ctrlr state to INIT.
Then rename spdk_nvme_ctrlr_reset_poll_async() by
spdk_nvme_ctrlr_reconnect_poll_async().
Finally deprecate spdk_nvme_ctrlr_reset_async() and
spdk_nvme_ctrlr_reset_poll_async().
The following patches will change the NVMe bdev module to use these new APIs.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Id1d6858dcdc5fc2e9db0a6ebf3f79cab4f9bbcb7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10091
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The nvmf library will use INTEL VID/SSVID/IEEE values by default,
each transport can overwrite them if needed.
Change-Id: I9dad521c4d080b6f0cc1aaeb4b5d5f6863c6846d
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10095
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch enables WARN_NO_PARAMDOC in Doxygen and
resolves remaining issues.
Void return type does not require documentation.
Some of the removed docs were not even Doxygen type
comment, see lack of '\'.
Fixed errors were similar to below:
spdk/include/spdk/nvmf.h:1081: warning: documented empty return type of spdk_nvmf_tgt_add_transport
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I6bb282ead8dc918885f7a89ab8829e4f5c477247
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10387
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Dong Yi <dongx.yi@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Documentation for spdk_scsi_dev_get_next_lun now matches
the function.
include/spdk/scsi.h:239: error: argument 'lun' of command @param is not found in the argument list of spdk_scsi_dev_get_next_lun(struct spdk_scsi_lun *prev_lun)
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I40512656cc215933fcd945429fac23318a083e09
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10384
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
behaviour for spdk_for_each_channel_continue was not clear when user
pass non 0 status, now it is clarified
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: I1aa5b5226e1aaf150ef069743f363f46d6c19e6d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10497
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
For any processed events, the function actually returns the number of them, not 0.
Signed-off-by: Maciej Szulik <maciej.szulik@intel.com>
Change-Id: I37bb456925e0b02c51276af169107e609d2bf301
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10229
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jacek Kalwas <jacek.kalwas@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add a parameter which determines the owner of the
map - target or initiator. It allows to set different
access flags when creating Memory Regions
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I0016847fe116e193d0954db1c8e65066b4ff82bf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10283
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Issue: spdk_top tracked pollers by the poller name string and the
thread_id they are running on. This shows incorrect stats when
multiple pollers exist on the same thread with the same name.
Solution: Added a unique poller id for each poller on a thread and
to allow spdk_top to track pollers by thread_id and poller_id.
Signed-off-by: Michael Piszczek <mpiszczek@ddn.com>
Change-Id: I1879e2afc9a929d1df9e8e35510f0092c5443bdc
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5868
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
In the bdev-zone API, there are a few functions that takes a zone_id:
spdk_bdev_get_zone_info(), spdk_bdev_zone_management(), and the
spdk_bdev_zone_append() functions.
The way a zoned application is usually written is that it starts off
by getting the zone report for all zones (zone_id will be sent in as 0),
and then the application will keep the whole zone report in memory.
Therefore, an application usually have access to the zone_id/zslba for
all zones. However, there are cases, e.g. when getting an error on write,
where the completion callback will only have the lba of the write that
failed.
Add a helper function that can be used to get the zone_id/slba for a
given lba. Having this helper in bdev-zone will avoid SPDK applications
needing to provide their own implementation for this.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I978335f87f7d49bc33aed81afcaa6d9f0af8a1e4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10180
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
There already is a spdk_u32_is_pow2() function that handles uint32_t.
Add a spdk_u64_is_pow2() function that handles uint64_t.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: Idc96680dbe280d1510aba94a6900eff64ccb4f03
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10179
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Clearly indicate that the value returned by this function has been
misinterpreted so many times that it has been rendered worthless.
Instead, software can use the functions to iterate the active namespaces
as a replacement.
Change-Id: I355f123eac0d33d63716cc333dc674d2ef226dc4
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10100
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
nvme_tcp_build_iovs() calculates the plen for
the iovs, but only uses the calculated value in
an assert, so we get set-but-not-used errors in
release builds. So mark the variable as unused
to squash those errors.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ifdf72faa6182c0fba622da9e5e2a33e3c6bbaf86
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10125
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Dong Yi <dongx.yi@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
