d/freebsd-dev
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
55221653c0
freebsd-dev/sys/mips/conf/AP135.hints

180 lines
5.1 KiB
Plaintext
Raw Normal View History

Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
# This is a placeholder until the hardware support is complete.
# I'm assuming this is an AP135-020. The AP136-010 in openwrt has
# the ethernet ports wired up to the switch in the reverse way.
# $FreeBSD$
# QCA955X_ETH_CFG_RGMII_EN (1 << 0)
hint.qca955x_gmac.0.gmac_cfg=0x1
# mdiobus0 on arge0
hint.argemdio.0.at="nexus0"
hint.argemdio.0.maddr=0x19000000
hint.argemdio.0.msize=0x1000
hint.argemdio.0.order=0
Fix both arge0 and arge1 to work correctly on the AP135. * Force the arge0 interface to not use a PHY for speed negotiation for now. It'd be nice to do it, but right now the RGMII interface to the switch needs to stay at 1000/full in order to match what the switch side of the port is programmed as. So until that's all sorted out, disconnect arge0 from the PHY and leave it at fixed at 1000/full. I noticed this when I tried using a busted ethernet cable that forced the PHY to negotiate 100/full. The switch was fine and it negotiated to 100/full, but then arge0 saw the link update and set the speed to 100/full when the switch side of that hook up was set to 1000/full. Tsk. * When using argemdio, the mdio device resets and initialises the MAC, /not/ the arge_attach (or, as I discovered, arge_init.) So arge1 wasn't being fully initialised and thus no traffic would ever flow. So until I tidy up that mess, just create an argemdio bus for arge1. It's totally fine; it won't do anything or find anything attached to it. Tested: * AP135 reference board - both arge0 and arge1 now work.
2015-03-04 03:48:11 +00:00
# mdiobus1 on arge1 - required to bring up arge1?
hint.argemdio.1.at="nexus0"
hint.argemdio.1.maddr=0x1a000000
hint.argemdio.1.msize=0x1000
hint.argemdio.1.order=0
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
# AR8327 - connected via mdiobus0 on arge0
hint.arswitch.0.at="mdio0"
hint.arswitch.0.is_7240=0 # definitely not the internal switch!
hint.arswitch.0.is_9340=0 # not the internal switch!
hint.arswitch.0.numphys=5 # all ports are PHYs
hint.arswitch.0.phy4cpu=0
hint.arswitch.0.is_rgmii=0 # not needed
hint.arswitch.0.is_gmii=0 # not needed
# This is where it gets a bit odd. port 0 and port 6 are CPU ports.
# The current code only supports one CPU port. So hm, what should
# we do to hook PAD6 up to be RGMII but a PHY, not a MAC?
# The other trick - how do we get arge1 (hooked up to GMAC0) to work?
# That's currently supposed to be hooked up to CPU port 0.
# Other AR8327 configuration parameters
# AP136-020 parameters
# GMAC0 AR8327 -> GMAC1 (arge1) SoC, SGMII
# AR8327_PAD_MAC_SGMII
hint.arswitch.0.pad.0.mode=3
#hint.arswitch.0.pad.0.rxclk_delay_sel=0
hint.arswitch.0.pad.0.sgmii_delay_en=1
# GMAC6 AR8327 -> GMAC0 (arge0) SoC, RGMII
# AR8327_PAD_MAC_RGMII
# XXX I think this hooks it up to the internal MAC6
hint.arswitch.0.pad.6.mode=6
hint.arswitch.0.pad.6.txclk_delay_en=1
hint.arswitch.0.pad.6.rxclk_delay_en=1
# AR8327_CLK_DELAY_SEL1
hint.arswitch.0.pad.6.txclk_delay_sel=1
# AR8327_CLK_DELAY_SEL2
hint.arswitch.0.pad.6.rxclk_delay_sel=2
# XXX there's no LED management just yet!
hint.arswitch.0.led.ctrl0=0x00000000
hint.arswitch.0.led.ctrl1=0xc737c737
hint.arswitch.0.led.ctrl2=0x00000000
hint.arswitch.0.led.ctrl3=0x00c30c00
hint.arswitch.0.led.open_drain=1
# force_link=1 is required for the rest of the parameters
# to be configured.
hint.arswitch.0.port.0.force_link=1
hint.arswitch.0.port.0.speed=1000
hint.arswitch.0.port.0.duplex=1
hint.arswitch.0.port.0.txpause=1
hint.arswitch.0.port.0.rxpause=1
# force_link=1 is required for the rest of the parameters
# to be configured.
hint.arswitch.0.port.6.force_link=1
hint.arswitch.0.port.6.speed=1000
hint.arswitch.0.port.6.duplex=1
hint.arswitch.0.port.6.txpause=1
hint.arswitch.0.port.6.rxpause=1
# arge0 - hooked up to AR8327 GMAC6, RGMII
Now that if_arge.c handles actual 'locked' media settings, enable the WAN port to look like it has its own PHY on PHY4 (port5).
2015-03-08 22:07:32 +00:00
# set at 1000/full to the switch.
# so, lock both sides of this connect up to 1000/full;
# if_arge thus wont change the PLL configuration
# upon a link status change.
Now that the switch PHY fully works, don't limit arge0 to only being up if the WAN port is up. This way I can use it for arbitrary ports/vlans.
2015-03-21 06:12:46 +00:00
hint.arge.0.phymask=0x0
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
hint.arge.0.miimode=3 # RGMII
Fix both arge0 and arge1 to work correctly on the AP135. * Force the arge0 interface to not use a PHY for speed negotiation for now. It'd be nice to do it, but right now the RGMII interface to the switch needs to stay at 1000/full in order to match what the switch side of the port is programmed as. So until that's all sorted out, disconnect arge0 from the PHY and leave it at fixed at 1000/full. I noticed this when I tried using a busted ethernet cable that forced the PHY to negotiate 100/full. The switch was fine and it negotiated to 100/full, but then arge0 saw the link update and set the speed to 100/full when the switch side of that hook up was set to 1000/full. Tsk. * When using argemdio, the mdio device resets and initialises the MAC, /not/ the arge_attach (or, as I discovered, arge_init.) So arge1 wasn't being fully initialised and thus no traffic would ever flow. So until I tidy up that mess, just create an argemdio bus for arge1. It's totally fine; it won't do anything or find anything attached to it. Tested: * AP135 reference board - both arge0 and arge1 now work.
2015-03-04 03:48:11 +00:00
hint.arge.0.media=1000
hint.arge.0.fduplex=1
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
hint.arge.0.pll_1000=0x56000000
# MAC for arge0 is the first 6 bytes of the ART
hint.arge.0.eeprommac=0x1fff0000
# arge1 - lock up to 1000/full
hint.arge.1.phymask=0x0
hint.arge.1.media=1000
hint.arge.1.fduplex=1
hint.arge.1.miimode=5 # SGMII
hint.arge.1.pll_1000=0x03000101
# MAC for arge1 is the second 6 bytes of the ART
hint.arge.1.eeprommac=0x1fff0006
[atheros] teach these two boards about the new hints location as well.
2018-02-01 22:00:38 +00:00
# Where the ART is - last 64k in the first 8MB of flash
hint.ar71xx_caldata.0.map.0.ath_fixup_addr=0x1fff0000
hint.ar71xx_caldata.0.map.0.ath_fixup_size=16384
# And now tell the ath(4) driver where to look!
hint.ath.0.eeprom_firmware="ar71xx_caldata.0.map.0.eeprom_firmware"
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
# flash layout:
#
# bootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),6336k(rootfs),1408k(uImage),8256k(mib0),64k(ART)
Update the AP135 reference design flash layout to be more useful. * Shuffle the kernel to be at the beginning * Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest * put the cfg parition just before the ART calibration data for the wifi part in the SoC * .. and make sure ART points to the right 64k region. I've updated the freebsd-wifi-build wiki the instructions on using this. If someone has an AP135 with 8MB SPI flash then this won't work; everything minus the big mib0 partition is just a bit over 8MB. Come see me if this ever happens (you'll likely just have to shrink the rootfs and the kernel a little in order to make it fit.) Tested: * AP135 reference board.
2015-10-10 05:00:18 +00:00
# The default flash layout isn't enough to fit a freebsd kernel
# now, so the layout has been shuffled around.
#
# By default it's set to:
# 256KB uboot, 64KB uboot-env, 6336KB rootfs, 1344KB kernel, 64KB cfg, 8256MB mib0, 64KB ART
# With 'bootcmd=bootm 0x9f680000' in the environment.
#
# Instead, now let's make it:
# 256KB uboot, 64KB uboot-env, 2048MB kernel, 6144MB rootfs, 7644KB mib0, 64KB cfg, 64KB ART
# .. and then you change the boot env to be:
# 'bootcmd=bootm 0x9f050000'
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
# 256KiB u-boot
hint.map.0.at="flash/spi0"
hint.map.0.start=0x00000000
hint.map.0.end=0x00040000 # 256k u-boot
hint.map.0.name="u-boot"
hint.map.0.readonly=1
# 64KiB u-boot-env
hint.map.1.at="flash/spi0"
hint.map.1.start=0x00040000
hint.map.1.end=0x00050000 # 64k u-boot-env
hint.map.1.name="u-boot-env"
hint.map.1.readonly=1
Update the AP135 reference design flash layout to be more useful. * Shuffle the kernel to be at the beginning * Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest * put the cfg parition just before the ART calibration data for the wifi part in the SoC * .. and make sure ART points to the right 64k region. I've updated the freebsd-wifi-build wiki the instructions on using this. If someone has an AP135 with 8MB SPI flash then this won't work; everything minus the big mib0 partition is just a bit over 8MB. Come see me if this ever happens (you'll likely just have to shrink the rootfs and the kernel a little in order to make it fit.) Tested: * AP135 reference board.
2015-10-10 05:00:18 +00:00
# 2048KiB kernel
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
hint.map.2.at="flash/spi0"
hint.map.2.start=0x00050000
Update the AP135 reference design flash layout to be more useful. * Shuffle the kernel to be at the beginning * Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest * put the cfg parition just before the ART calibration data for the wifi part in the SoC * .. and make sure ART points to the right 64k region. I've updated the freebsd-wifi-build wiki the instructions on using this. If someone has an AP135 with 8MB SPI flash then this won't work; everything minus the big mib0 partition is just a bit over 8MB. Come see me if this ever happens (you'll likely just have to shrink the rootfs and the kernel a little in order to make it fit.) Tested: * AP135 reference board.
2015-10-10 05:00:18 +00:00
hint.map.2.end=0x00250000 # 2048k rootfs
hint.map.2.name="kernel"
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
hint.map.2.readonly=1
Update the AP135 reference design flash layout to be more useful. * Shuffle the kernel to be at the beginning * Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest * put the cfg parition just before the ART calibration data for the wifi part in the SoC * .. and make sure ART points to the right 64k region. I've updated the freebsd-wifi-build wiki the instructions on using this. If someone has an AP135 with 8MB SPI flash then this won't work; everything minus the big mib0 partition is just a bit over 8MB. Come see me if this ever happens (you'll likely just have to shrink the rootfs and the kernel a little in order to make it fit.) Tested: * AP135 reference board.
2015-10-10 05:00:18 +00:00
# 6144KiB rootfs
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
hint.map.3.at="flash/spi0"
Update the AP135 reference design flash layout to be more useful. * Shuffle the kernel to be at the beginning * Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest * put the cfg parition just before the ART calibration data for the wifi part in the SoC * .. and make sure ART points to the right 64k region. I've updated the freebsd-wifi-build wiki the instructions on using this. If someone has an AP135 with 8MB SPI flash then this won't work; everything minus the big mib0 partition is just a bit over 8MB. Come see me if this ever happens (you'll likely just have to shrink the rootfs and the kernel a little in order to make it fit.) Tested: * AP135 reference board.
2015-10-10 05:00:18 +00:00
hint.map.3.start=0x00250000
hint.map.3.end=0x00850000
hint.map.3.name="rootfs"
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
hint.map.3.readonly=1
Update the AP135 reference design flash layout to be more useful. * Shuffle the kernel to be at the beginning * Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest * put the cfg parition just before the ART calibration data for the wifi part in the SoC * .. and make sure ART points to the right 64k region. I've updated the freebsd-wifi-build wiki the instructions on using this. If someone has an AP135 with 8MB SPI flash then this won't work; everything minus the big mib0 partition is just a bit over 8MB. Come see me if this ever happens (you'll likely just have to shrink the rootfs and the kernel a little in order to make it fit.) Tested: * AP135 reference board.
2015-10-10 05:00:18 +00:00
# 7644KiB mib0
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
hint.map.4.at="flash/spi0"
Update the AP135 reference design flash layout to be more useful. * Shuffle the kernel to be at the beginning * Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest * put the cfg parition just before the ART calibration data for the wifi part in the SoC * .. and make sure ART points to the right 64k region. I've updated the freebsd-wifi-build wiki the instructions on using this. If someone has an AP135 with 8MB SPI flash then this won't work; everything minus the big mib0 partition is just a bit over 8MB. Come see me if this ever happens (you'll likely just have to shrink the rootfs and the kernel a little in order to make it fit.) Tested: * AP135 reference board.
2015-10-10 05:00:18 +00:00
hint.map.4.start=0x00850000
hint.map.4.end=0x00fe0000
hint.map.4.name="mib0"
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
hint.map.4.readonly=0
Update the AP135 reference design flash layout to be more useful. * Shuffle the kernel to be at the beginning * Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest * put the cfg parition just before the ART calibration data for the wifi part in the SoC * .. and make sure ART points to the right 64k region. I've updated the freebsd-wifi-build wiki the instructions on using this. If someone has an AP135 with 8MB SPI flash then this won't work; everything minus the big mib0 partition is just a bit over 8MB. Come see me if this ever happens (you'll likely just have to shrink the rootfs and the kernel a little in order to make it fit.) Tested: * AP135 reference board.
2015-10-10 05:00:18 +00:00
# 64KiB cfg
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
hint.map.5.at="flash/spi0"
Update the AP135 reference design flash layout to be more useful. * Shuffle the kernel to be at the beginning * Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest * put the cfg parition just before the ART calibration data for the wifi part in the SoC * .. and make sure ART points to the right 64k region. I've updated the freebsd-wifi-build wiki the instructions on using this. If someone has an AP135 with 8MB SPI flash then this won't work; everything minus the big mib0 partition is just a bit over 8MB. Come see me if this ever happens (you'll likely just have to shrink the rootfs and the kernel a little in order to make it fit.) Tested: * AP135 reference board.
2015-10-10 05:00:18 +00:00
hint.map.5.start=0x00fe0000
hint.map.5.end=0x00ff0000
hint.map.5.name="cfg"
hint.map.5.readonly=0
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
# 64KiB ART
hint.map.6.at="flash/spi0"
Update the AP135 reference design flash layout to be more useful. * Shuffle the kernel to be at the beginning * Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest * put the cfg parition just before the ART calibration data for the wifi part in the SoC * .. and make sure ART points to the right 64k region. I've updated the freebsd-wifi-build wiki the instructions on using this. If someone has an AP135 with 8MB SPI flash then this won't work; everything minus the big mib0 partition is just a bit over 8MB. Come see me if this ever happens (you'll likely just have to shrink the rootfs and the kernel a little in order to make it fit.) Tested: * AP135 reference board.
2015-10-10 05:00:18 +00:00
hint.map.6.start=0x00ff0000
Add support for the AP135 2.0 reference platform. This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3 NIC and an AR8327 gigabit ethernet switch. TODO: * The AR8327 gigabit switch support bugfixes are forthcoming. * 11ac support and 11ac NIC support
2015-03-02 02:27:25 +00:00
hint.map.6.end=0x01000000 # 64k ART
hint.map.6.name="ART"
hint.map.6.readonly=1
Reference in New Issue Copy Permalink