reboot. Safter the reboot the TCC is usually in the Automatic mode, in which
reading current performance level is likely to produce bogus results make sure
to switch it to the On-Demand mode and set to some known performance level.
Unfortunately there is no reliable way to check that TCC is in the Automatic
mode. Reading bit 4 of ACPI Thermal Monitor Control Register produces 0
regardless of the current mode.
MFC after: 1 week
uses the i8237 without trying to emulate the PC architecture move
the register definitions for the i8237 chip into the central include
file for the chip, except for the PC98 case which is magic.
Add new isa_dmatc() function which tells us as cheaply as possible
if the terminal count has been reached for a given channel.
devclass. As pointed out by dfr@, devclasses don't have to share the same
linkage if multiple drivers have the same name. Newbus should match the
devclasses based on name and allocate non-conflicting unit numbers.
millisecond it is calibrating. Suggested by jhb@ and bde@. Don't clobber
the tsc_freq with the new value since it isn't accurate enough for
timecounters and the timecounter system as a whole needs support for
changing rates before we do this. Subtract 0.5% from our measurement
to account for overhead in DELAY. Note that this interface is for
estimating the clockrate and needs to work well at runtime so doing a full
calibration including disabling interrupts for a second is not feasible.
interrupts, read from the interrupt status register to clear any pending
interrupts. Otherwise in some rare cases the RTC would never fire any
interrupts as it constantly thinks it has an interrupt pending.
PR: i386/17800
PR: kern/76776
Submitted by: Jose M. Alcaide jose at we dot lc dot ehu dot es
MFC after: 2 weeks
copies arguments into the kernel space and one that operates
completely in the kernel space;
o use kernel-only version of execve(2) to kill another stackgap in
linuxlator/i386.
Obtained from: DragonFlyBSD (partially)
MFC after: 2 weeks
i386_{get,set}_ioperm() and make those APIs visible in the kernel namespace;
o use i386_{get,set}_ldt() and i386_{get,set}_ioperm() instead of sysarch()
in the linuxlator, which allows to kill another two stackgaps.
MFC after: 2 weeks
interrupts that have a trigger mode of conforming. This fixes problems on
some older machines that still route PCI devices via ISA interrupts when
using an I/O APIC.
Tested by: Peter Trifonov pvtrifonov at mail dot ru
MFC after: 1 month
instead of burying that in the atpic(4) code as atpic(4) is not the only
user of elcr(4). Change the elcr(4) code to export a global elcr_found
variable that other code can check to see if a valid ELCR was found.
MFC after: 1 month
(calling a __dead2 function such as panic() at the end of a function), the
saved %eip on the stack will actually not be part of the function that
executed a call instruction but instead will be the first instruction of
the next function in the text. This happens with dblfault_handler() and
syscall() for example. Work around this in the one place it matters by
looking at the saved %eip - 1 to determine the calling function when we
check for "magic" frames.
MFC after: 2 weeks
interrupt is wired up to all the I/O APICs in the system. If the system
has only one I/O APIC, then just act as if the entry specified that APIC.
We still don't try to handle global entries in a system with multiple I/O
APICs.
Tested by: Peter Trifonov pvtrifonov at mail dot ru
MFC after: 1 week
- Fix the MP Table pci bridge drivers to not probe the configuration table
unless we actually have one. Machines using a default configuration do
not have such a table.
- Only allow default configuration types of 5 (ISA + PCI) and 6 (EISA +
PCI) as the others are not likely to work. Types 1 through 4 use an
external APIC (probably with 80486 processors) which we certainly do not
support, and type 7 uses an MCA bus which has not been tested with the
new MP Table code.
- Correct the fact that the single I/O APIC in a default configuration has
an ID of 2, not 0.
- Fix off by one errors in setting the bus types from the default_data[]
arrays for default configurations.
- Explicitly configure each of the 16 interrupt pins on the sole I/O APIC
when using a default configuration. This is especially helpful for type
6 (EISA + PCI) since the EISA interrupts need to have their polarity
programmed based on the values in the ELCR.
Much thanks to the submitter and tester who endured several rounds of
testing to get this fixed.
MFC after: 1 week
Tested by: Georg Schwarz georg dot schwarz at freenet dot de
cuts to the chase and fills in a provided s/g list. This is meant to optimize
out the cost of the callback since the callback doesn't serve much purpose for
mbufs since mbuf loads will never be deferred. This is just for amd64 and
i386 at the moment, other arches will be coming shortly.
from 4.x kernel config files. User's wishing to upgrade from 4.x to 6
will need to go through 5.x, or grab this script from there. These
scripts will remain in RELENG_5...
other comments. Clarify that the next two things needed for SMP are
two lines.
- Expand mii abbreviation to miibus for clarity in the USB ethernet
comment.
system from an AP at runtime (i.e., calling cpu_reset from ddb). Someday,
if we move to an NMI for stopping cpus instead, we can do away with this.
Requested by: jhb
though these aren't used yet.
- Add missing function prototypes for some static functions.
- Allow lvt_mode() to handle an LVT entry with a delivery mode of fixed.
- Consolidate code duplicated in lapic_init() and lapic_setup() to program
the spurious vector register of a local APIC in a static lapic_enable()
function.
- Dump the timer, thermal, error, and performance counter LVT entries
during lapic_dump().
- Program LVT pins (currently only LINT0 and LINT1) after the local
APIC has been software enabled via lapic_enable() since otherwise the
LVT programming will not be able to unmask LVT sources.
on entry and it assumes the responsibility for releasing the page queues
lock if it must sleep.
Remove a bogus comment from pmap_enter_quick().
Using the first change, modify vm_map_pmap_enter() so that the page queues
lock is acquired and released once, rather than each time that a page
is mapped.
