VM_PHYSSEG_SPARSE depending on whether the physical address space is
densely or sparsely populated with memory. The effect of this
definition is to determine which of two implementations of
vm_page_array and PHYS_TO_VM_PAGE() is used. The legacy
implementation is obtained by defining VM_PHYSSEG_DENSE, and a new
implementation that trades off time for space is obtained by defining
VM_PHYSSEG_SPARSE. For now, all architectures except for ia64 and
sparc64 define VM_PHYSSEG_DENSE. Defining VM_PHYSSEG_SPARSE on ia64
allows the entirety of my Itanium 2's memory to be used. Previously,
only the first 1 GB could be used. Defining VM_PHYSSEG_SPARSE on
sparc64 allows USIIIi-based systems to boot without crashing.
This change is a combination of Nathan Whitehorn's patch and my own
work in perforce.
Discussed with: kmacy, marius, Nathan Whitehorn
PR: 112194
- Simplify the amount of work that has be done for each architecture by
pushing more of the truly MI code down into the PCI bus driver.
- Don't bind MSI-X indicies to IRQs so that we can allow a driver to map
multiple MSI-X messages into a single IRQ when handling a message
shortage.
The changes include:
- Add a new pcib_if method: PCIB_MAP_MSI() which is called by the PCI bus
to calculate the address and data values for a given MSI/MSI-X IRQ.
The x86 nexus drivers map this into a call to a new 'msi_map()' function
in msi.c that does the mapping.
- Retire the pcib_if method PCIB_REMAP_MSIX() and remove the 'index'
parameter from PCIB_ALLOC_MSIX(). MD code no longer has any knowledge
of the MSI-X index for a given MSI-X IRQ.
- The PCI bus driver now stores more MSI-X state in a child's ivars.
Specifically, it now stores an array of IRQs (called "message vectors" in
the code) that have associated address and data values, and a small
virtual version of the MSI-X table that specifies the message vector
that a given MSI-X table entry uses. Sparse mappings are permitted in
the virtual table.
- The PCI bus driver now configures the MSI and MSI-X address/data
registers directly via custom bus_setup_intr() and bus_teardown_intr()
methods. pci_setup_intr() invokes PCIB_MAP_MSI() to determine the
address and data values for a given message as needed. The MD code
no longer has to call back down into the PCI bus code to set these
values from the nexus' bus_setup_intr() handler.
- The PCI bus code provides a callout (pci_remap_msi_irq()) that the MD
code can call to force the PCI bus to re-invoke PCIB_MAP_MSI() to get
new values of the address and data fields for a given IRQ. The x86
MSI code uses this when an MSI IRQ is moved to a different CPU, requiring
a new value of the 'address' field.
- The x86 MSI psuedo-driver loses a lot of code, and in fact the separate
MSI/MSI-X pseudo-PICs are collapsed down into a single MSI PIC driver
since the only remaining diff between the two is a substring in a
bootverbose printf.
- The PCI bus driver will now restore MSI-X state (including programming
entries in the MSI-X table) on device resume.
- The interface for pci_remap_msix() has changed. Instead of accepting
indices for the allocated vectors, it accepts a mini-virtual table
(with a new length parameter). This table is an array of u_ints, where
each value specifies which allocated message vector to use for the
corresponding MSI-X message. A vector of 0 forces a message to not
have an associated IRQ. The device may choose to only use some of the
IRQs assigned, in which case the unused IRQs must be at the "end" and
will be released back to the system. This allows a driver to use the
same remap table for different shortage values. For example, if a driver
wants 4 messages, it can use the same remap table (which only uses the
first two messages) for the cases when it only gets 2 or 3 messages and
in the latter case the PCI bus will release the 3rd IRQ back to the
system.
MFC after: 1 month
vm.kmem_size_min. Useful when using ZFS to make sure that vm.kmem size will
be at least 256mb (for example) without forcing a particular value via vm.kmem_size.
Approved by: njl (mentor)
Reviewed by: alc
address ranges used by local and I/O APICs in the system. Some systems
also reserve these ranges as system resources via either PnPBIOS or
ACPI, so this device currently attaches after acpi0 and legacy0 so that
the system resources are given precedence.
variable to avoid invalid constraints in dead code. Use an array of
u_char's (inside a struct) instead of a char/short/int/long variable so
that the variable and its accesses can be spelled in the same way in all
cases and code doesn't need to be cloned just to hold the spelling
differences.
Fixed strict-aliasing errors in PCPU_SET() and in the amd64 PCPU_GET().
Cast to (void *) as in rev.1.37 of the i386 version where the errors
were fixed for the i386 PCPU_GET() only. It would be more correct to
copy to and from the temp. variable using memcpy(), but then an
ifdef tangle would be required to ensure using the builtin memcpy().
We depend on fairly aggressive optimization to put the temp. variable
only in a register despite it being copied using
*(type *)(void *)&anothertype and could depend on this when using
memcpy() too. This seems to work right even for -O0, but the -O0 case
has not been completely tested.
This change gives identical object code for all object files in LINT
on amd64 (except for one file with a __TIME__ stamp). For LINT on
i386 it gives unimportant differences in instruction order and padding
in a few object files. This was only tested for -O.
This change (actually a previous version of it) gives the following
reductions in the number of object files in LINT that fail to compile
with -O2 but without the -fno-strict-aliasing kludge:
- amd64: 29 (down from 211)
- i386: 36 (down from 47)
gcc-3.4.6 actually allows the invalid constraints that result from not
using the temp. variable, at least with -O[1-2], but gcc-3.3.3 crashes
on them and I don't want to depend on compiler bugs.
register takes 16 characters (64-bit register in hex). In practice this
is a slight bit of overkill as 7 of the 56 registers are only 32-bit, but
having the buffer too small results in remote kgdb trashing kernel memory
when it connects.
PR: amd64/108673
Submitted by: Ravi Murty, Nikhil Rao @ Intel
MFC after: 3 days
used by clock code, so don't export it to the world for machdep.c to
initialize. There is a minor problem initializing it before it is
used, since although clock initialization is split up so that parts
of it can be done early, the first part was never done early enough
to actually work. Split it up a bit more and do the first part as
late as possible to document the necessary order. The functions that
implement the split are still bogusly exported.
Cleaned up initialization of the i8254 clock hardware using the new
split. Actually initialize it early enough, and don't work around it
not being initialized in DELAY() when DELAY() is called early for
initialization of some console drivers.
This unfortunately moves a little more code before the early debugger
breakpoint so that it is harder to debug. The ordering of console and
related initialization is delicate because we want to do as little as
possible before the breakpoint, but must initialize a console.
- First off, device drivers really do need to know if they are allocating
MSI or MSI-X messages. MSI requires allocating powerof2() messages for
example where MSI-X does not. To address this, split out the MSI-X
support from pci_msi_count() and pci_alloc_msi() into new driver-visible
functions pci_msix_count() and pci_alloc_msix(). As a result,
pci_msi_count() now just returns a count of the max supported MSI
messages for the device, and pci_alloc_msi() only tries to allocate MSI
messages. To get a count of the max supported MSI-X messages, use
pci_msix_count(). To allocate MSI-X messages, use pci_alloc_msix().
pci_release_msi() still handles both MSI and MSI-X messages, however.
As a result of this change, drivers using the existing API will only
use MSI messages and will no longer try to use MSI-X messages.
- Because MSI-X allows for each message to have its own data and address
values (and thus does not require all of the messages to have their
MD vectors allocated as a group), some devices allow for "sparse" use
of MSI-X message slots. For example, if a device supports 8 messages
but the OS is only able to allocate 2 messages, the device may make the
best use of 2 IRQs if it enables the messages at slots 1 and 4 rather
than default of using the first N slots (or indicies) at 1 and 2. To
support this, add a new pci_remap_msix() function that a driver may call
after a successful pci_alloc_msix() (but before allocating any of the
SYS_RES_IRQ resources) to allow the allocated IRQ resources to be
assigned to different message indices. For example, from the earlier
example, after pci_alloc_msix() returned a value of 2, the driver would
call pci_remap_msix() passing in array of integers { 1, 4 } as the
new message indices to use. The rid's for the SYS_RES_IRQ resources
will always match the message indices. Thus, after the call to
pci_remap_msix() the driver would be able to access the first message
in slot 1 at SYS_RES_IRQ rid 1, and the second message at slot 4 at
SYS_RES_IRQ rid 4. Note that the message slots/indices are 1-based
rather than 0-based so that they will always correspond to the rid
values (SYS_RES_IRQ rid 0 is reserved for the legacy INTx interrupt).
To support this API, a new PCIB_REMAP_MSIX() method was added to the
pcib interface to change the message index for a single IRQ.
Tested by: scottl
MPLOCKED. The cleaning in rev.1.25 was supposed to have been undone
by rev.1.26, but 1.26 could never have actually affected asm files
since atomic.h is full of C declarations so including it in asm files
would just give syntax errors. The asm MPLOCKED is even less needed
than when misplaced definitions of it were first removed, and is now
unused in any asm file in the src tree except in anachronismns in
sys/i386/i386/support.s.
mainly involves removing all __CC_SUPPORTS___INLINE__ ifdefs. These
ifdefs are even less needed for amd64 than for i386, but the i386
atomic.h never had them. The ifdefs here were just an optimization
of obsolescent compatibility cruft (__inline) for a null set of
compilers. I think null sets of compilers should only be supported
in cases where this is more than an optimization, doesn't require
extensive ifdefs, and only involves not-so-obsolescent compatibility
cruft (plain inline here).
These functions are used a lot for mutexes, so this reduces the text
size of an average kernel by about 0.75%. This wasn't intended to
be a significant optimization, but it somehow increased the maximum
number of packets per second that can be transmitted by my bge hardware
from 320000 to 460000 (this benchmark is CPU-bound and remarkably
sensitive to changes in the text section).
Details: we would prefer to leave the result of the cmpxchg in %al,
but cannot tell gcc that it is there, so we have to convert it to an
integer register. We converted to %al, then to %[re]ax, but the
latter step is usually wasted since gcc usually only wants the condition
code and can recover it from %al just as easily as from %[re]ax. Let
gcc promote %al in the few cases where this is needed.
Nearby style fixes;
- let gcc manage the load of `res', and don't abuse `res' for a copy of `exp'
- don't echo `res's name in comments
- consistently spell the condition code as 'e' after comparison for equality
- don't hard-code %al anywhere except in constraints
- for the version that doesn't use cmpxchg, there is no requirement to use
%al anywhere, so don't hard-code it in the constraints either.
Style non-fix:
- for the versions that use cmpxchg, keep using "a" (was %[re]ax, now %al)
for the main output operand, although this is not required. The input
and output operands that use the "a" constraint are now decoupled, and
this makes things clearer except for the reason that the output register
is hard-coded. It is now just a hack to tell gcc that the input "a" has
been clobbered without increasing the number of operands.
as if they were really passed by reference. Specifically, the dead stores
elimination pass in the GCC 4.1 optimiser breaks the non-compliant behavior
on which FreeBSD relied. This change brings FreeBSD up to date by switching
trap frames to being explicitly passed by reference.
Reviewed by: kan
Tested by: kan
of various scattered magic values.
- Pretty print the address of hardware watchpoints in 'show watch' rather
than just displaying hex.
- Expand address field width on amd64 for 64-bit pointers.
- Add a new apic_alloc_vectors() method to the local APIC support code
to allocate N contiguous IDT vectors (aligned on a M >= N boundary).
This function is used to allocate IDT vectors for a group of MSI
messages.
- Add MSI and MSI-X PICs. The PIC code here provides methods to manage
edge-triggered MSI messages as x86 interrupt sources. In addition to
the PIC methods, msi.c also includes methods to allocate and release
MSI and MSI-X messages. For x86, we allow for up to 128 different
MSI IRQs starting at IRQ 256 (IRQs 0-15 are reserved for ISA IRQs,
16-254 for APIC PCI IRQs, and IRQ 255 is reserved).
- Add pcib_(alloc|release)_msi[x]() methods to the MD x86 PCI bridge
drivers to bubble the request up to the nexus driver.
- Add pcib_(alloc|release)_msi[x]() methods to the x86 nexus drivers that
ask the MSI PIC code to allocate resources and IDT vectors.
MFC after: 2 months
of NKPT is no longer enough to run amd64 with 16G of RAM, as it
doesn't have space for mapping a kernel (16M kernel would require
additionally 8 page tables).
- Don't use a frame pointer. Our callers need a frame pointer, but we
could only use one to support things that aren't supported. (These
things are:
- profiling of profiling
- debugging of profiling. The core ENTRY() macro doesn't support
forcing a frame pointer for debugging, so don't do more here.)
- Ensure that we are in the text section and have normal alignment.
- Use the normal syntax for `.type'.
Fixed a syntax error for the (!__KERNEL && !__GNUCLIKE_ASM) case in
rev.1.36. Apparently, this case has never been reached even by lint.
Submitted by: stefanf
{amd64,i386}/include/profile.h:
In case the above case is actually reached, break it properly by
providing null support that will fail at link time instead of a stub
that gives wrong (null) profiling at runtime.
this used to be slightly cleaner than using ifdefs in a few places to
support both a.out and elf, but using it now just causes messes and
unportabilities. It seems to be impossible to implement the elf
HIDENAME() portably in cpp (since token pasting of "." and <name> is
invalid).
*/prof_machdep.c:
- Removed all uses of CNAME(). CNAME() is easy enough to use in pure
asm code, but using it in inline asm requires messy quoting. The
core pure asm code has been hacked on more and all uses of CNAME() in
it have already gone away. Just assume the elf convention here too.
- Removed now-uneeded include of <machine/asmacros.h>.
- Removed the workaround for a namespace conflict with this include.
profiling is configured but high resolution profiling is not configured.
Only functions in *.[Ss] called the stub, so efficiency was not
significantly affected.
(PICs) rather than interrupt sources. This allows interrupt controllers
with no interrupt pics (such as the 8259As when APIC is in use) to
participate in suspend/resume.
- Always register the 8259A PICs even if we don't use any of their pins.
- Explicitly reset the 8259As on resume on amd64 if 'device atpic' isn't
included.
- Add a "dummy" PIC for the local APIC on the BSP to reset the local APIC
on resume. This gets suspend/resume working with APIC on UP systems.
SMP still needs more work to bring the APs back to life.
The MFC after is tentative.
Tested by: anholt (i386)
Submitted by: Andrea Bittau <a.bittau at cs.ucl.ac.uk> (3)
MFC after: 1 week
Submitted by:
Reviewed by:
Approved by:
Obtained from:
MFC after:
Security:
Move the relocation definitions to the common elf header so that DTrace
can use them on one architecture targeted to a different one.
Add the additional ELF types defines in Sun's "Linker and Libraries"
manual.
WB (write-back) on x86 via control bits in PTEs and PDEs (including making
use of the PAT MSR). Changes include:
- A new pmap_mapdev_attr() function for amd64 and i386 which takes an
additional parameter (relative to pmap_mapdev()) specifying the cache
mode for this mapping. Note that on amd64 only WB mappings are done with
the direct map, all other modes result in a private mapping.
- pmap_mapdev() on i386 and amd64 now defaults to using UC (uncached)
mappings rather than WB. Previously we relied on the BIOS setting up
MTRR's to enforce memio regions being treated as UC. This might make
hw.cbb_start_memory unnecessary in some cases now for example.
- A new pmap_mapbios()/pmap_unmapbios() API has been added to allow places
that used pmap_mapdev() to map non-device memory (such as ACPI tables)
to do so using WB as before.
- A new pmap_change_attr() function for amd64 and i386 that changes the
caching mode for a range of KVA.
Reviewed by: alc
