The GMII control bit ETH_MAC_CR_GMII_EN_ is not documented in
LAN78xx datasheets, but from the permissively licensed header provided
by Microchip it is:
#define ETH_MAC_CR_GMII_EN (0x00080000UL ) // GMII/RGMII Selection
is that current one (mass storage device) doesn't work as it is - it
needs to be set to 0 after the LUN is configured, which is what the
cfumass rc script does. In other words: the current default does not
work, and to actually make it work it had to be set to -1 in
/boot/loader.conf.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Previously lan78xx_chip_init locked the driver's mutex if not already
locked, but unlocked it only in the case of error. This provided a
fairly clear indication that the function is already called with the
lock held, so just replace it with a lock assertion.
Sponsored by: The FreeBSD Foundation
This driver was developed for the LAN7800 and the register-compatible
LAN7515 and has only been tested on those devices. Adding support for
other members of the family should be straightforward, once we have
devices to test.
With this change the driver will probe but fail to attach due to the
Chip ID check, but will leave a hint leading to the driver that needs
work.
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15537
This driver was developed for the LAN7800 and the register-compatible
LAN7515 (found on Raspberry Pi 3B+) and has only been tested on those
devices.
Sponsored by: The FreeBSD Foundation
This change adds support for a UBS<->RS232 adapter based on CH340 (or an
analogue) that I own. The device seems to have a newer internal version
(0x30) and the existing code incorrectly configures line control for it
resulting in garbled transmission. The changes are based on what I
learned in Linux drivers for the same hardware.
Additional changes:
- use UCHCOM_REG_LCR1 / UCHCOM_REG_LCR2 instead of explicit 0x18 and
0x25
- use NULL instead of 0 where a pointer is expected
Reviewed by: hselasky
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D15498
Also, add definitions for more bits of UCHCOM_REG_LCR1 as seen in the
Linux driver. UCHCOM_LCR1_PARENB definition was different from that in
the Linux driver and clashed with newly added UCHCOM_LCR1_RX. I took a
liberty to change UCHCOM_LCR1_PARENB to the Linux definition as it was
unused in the driver anyway. This change should make
uchcom_cfg_set_break() easier to understand.
Approved by: hselasky
MFC after: 2 weeks
Product IDs are specified in vendor documents. The previously used
device ID is not. This is a cosmetic change. No functionality depends
on those IDs.
Reviewed by: hselasky
MFC after: 2 weeks
muge was committed to the tree in r333713 but not yet connected to the
tree, and it crossed paths with the migration to using ck.
Sponsored by: The FreeBSD Foundation
Microchip provided a permissively-licensed lan78xx header, which has
an 'ETH_' prefix on most definitions. Follow suit in our driver.
Sponsored by: The FreeBSD Foundation
storage, CDC ACM (serial), and CDC ECM (ethernet) at the same time.
It's quite similar in function to Linux' "g_multi" gadget.
Reviewed by: hselasky@
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
one character too many. Note that this function is only used to decode
string descriptors generated by the kernel itself.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
This driver supports two Microchip USB-Ethernet controllers:
LAN7800 USB 3.1 to 10/100/1000 Mbps Ethernet
LAN7515 USB 2 to 10/100/1000 Mbps Ethernet with built-in USB hub
The LAN7515 is the Ethernet controller on the Raspberry Pi 3B+.
At present there is no datasheet for the LAN7515, but it is effectively
a USB 2 hub combined with a LAN7800 controller. A comprehensive LAN7800
datasheet is at http://www.microchip.com/wwwproducts/en/LAN7800.
This driver is based on the structure of the smsc(4) driver which
supports Microchip/SMSC's LAN95xx family. (Microchip acquired SMSC
in May 2012.) The Linux lan78xx driver served as a reference for some
functionality and registers.
The 'muge' driver name comes from "Microchip USB Gigabit Ethernet".
I made some style adjustments and minor edits to Arshan's submission.
It will be connected to the build after additional review and testing.
Thanks to Microchip for providing a number of Evaluation Boards (EVBs)
for development and testing.
Submitted by: Arshan Khanifar
Reviewed by: hselasky (earlier)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15168
LAN7800 USB 3.1 to 10/100/1000 Ethernet with PHY
LAN7801 USB 3.1 to 10/100/1000 Ethernet with RGMII interface
Also update manufacturer name for the Vendor ID. Microchip acquired
SMSC in May 2012.
Sponsored by: The FreeBSD Foundation
through a SYSCTL instead of a compile time define.
Add quirk by default for all LynxPoint XHCI controllers.
PR: 227602
MFC after: 3 days
Sponsored by: Mellanox Technologies
Per the datasheet, the BUSY bit must be set when reading or writing PHY
registers. From Linux commit 80928805babf.
Submitted by: Arshan Khanifar
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15217
In smsc_phy_init function, when the driver was trying to reset PHY, it
didn't poll for the correct bit (BMCR_RESET) to be cleared. Instead, it
anded it with MII_BMCR (which is 0), so it just exited the loop.
This issue was fixed in Linux in commit d94609200069.
Submitted by: Arshan Khanifar
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
device-side (and only device-side) "virtual USB serial adapters" - the
ones you can get with an OTG-capable board - as consoles. It boils down
to adding the device name to kern.console sysctl, although doing that
requires jumping through some hoops. It doesn't change the actual
operation of those virtual devices. The point is to make it possible
for init(8) to recognize them as console devices and to launch getty(8)
for them, when configured as "onifconsole" in ttys(5). The point of
that, in turn, is to add such entries to the default ttys(5), so that
init(8) will launch gettys for device-side "virtual serial adapters",
but not for actual USB serial dongles.
Reviewed by: hselasky@
No objections: imp@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
OF_getprop_alloc takes element size argument and returns number of
elements in the property. There are valid use cases for such behavior
but mostly API consumers pass 1 as element size to get string
properties. What API users would expect from OF_getprop_alloc is to be
a combination of malloc + OF_getprop with the same semantic of return
value. This patch modifies API signature to match these expectations.
For the valid use cases with element size != 1 and to reduce
modification scope new OF_getprop_alloc_multi function has been
introduced that behaves the same way OF_getprop_alloc behaved prior to
this patch.
Reviewed by: ian, manu
Differential Revision: https://reviews.freebsd.org/D14850
opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.
Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.
Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.
Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941
A series of zero delay callouts can happen causing high CPU usage of the
timer subsystem when trying to repeat keys, because the time of the
absolute timeout is not moving forward. The condition clears when all
keys are released.
Reported by: Johannes Lundberg <johalun0@gmail.com>
Discussed with: bde@
PR: 226968
MFC after: 1 week
Sponsored by: Mellanox Technologies
endpoints. The Allwinner driver will need to set this as the EPINFO
register isn't useful there.
Submitted by: jmcneill
Reviewed by: hselasky
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D5881
On the Allwinner SoCs we need to set a custom endpoint configuration. To
allow for this use a table to store the configuration so the attachment
can override it.
Reviewed by: hselasky
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14783
Move copy-pasted code for RTS/CTS frame allocation into net80211.
While here, add stat / debug message for allocation failures
(copied from run(4)) + return error here in bwn(4).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D14628
the jtag port, so that a tty is not created for it.
This is based on information in the PR and from the vendor website. When
the PR was first opened we had no facility for flagging the jtag ports. I
stumbled across the still-open PR with the idea of closing it, and noticed
that this wee update was needed.
PR: 175893
network device pointer might be NULL. Wait for any pending tasks to
complete before calling axge_stop().
MFC after: 1 week
Sponsored by: Mellanox Technologies
would be safe, but the function also tries to destroy mutexes that never
got created).
I guess this can only happen when imx_ehci_detach() is called on the
error-exit path from imx_ehci_attach(), and that path never got exercised
before today.
artificial NOMATCH usb does in lieu of creating a device_t for devices
with no drivers. Also, correct bus to be 'uhub' since where USB
devices attach, even though 'usb' is more logical, we need the
physical bus here.
Submitted by: hps@
host to reprobe the bus by switching the USB pull up resistors off and
back on. In other words - when FreeBSD is configured as a USB device,
changing the sysctl will be immediately noticed by the machine it's
connected to.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Similarly as other extres pseudo-drivers, implement phy by using kobj model.
This detaches it from provider device, so single device driver can export
multiple different phys. Additionally, this allows phy to be subclassed to
more specialized drivers, like is USB OTG phy, or PCIe phy with hot-plug
capability.
Tested by: manu (previous version, on Allwinner board)
MFC after: 1 month
possible to change string and numeric vendor and product identifiers,
as well as anything else there might be to change for a particular
device side template, eg the MAC address.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D13920
This removes the direct WME info access in the ieee80211com struct and instead
provides a method of fetching the data. Right now it's a no-op but eventually
it'll turn into a per-VAP method for drivers that support it (eg iwn, iwm,
upcoming ath10k work) as things like p2p support require this kind of behaviour.
Tested:
* ath(4), STA and AP mode
TODO:
* yes, this is slightly stack size-y, but it is an important first step
to get drivers migrated over to a sensible WME API. A lot of per-phy things
need to be converted to per-VAP before P2P, 11ac firmware, etc stuff shows up.
This reduces noise when kernel is compiled by newer GCC versions,
such as one used by external toolchain ports.
Reviewed by: kib, andrew(sys/arm and sys/arm64), emaste(partial), erj(partial)
Reviewed by: jhb (sys/dev/pci/* sys/kern/vfs_aio.c and sys/kern/kern_synch.c)
Differential Revision: https://reviews.freebsd.org/D10385
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
Initially, only tag files that use BSD 4-Clause "Original" license.
RelNotes: yes
Differential Revision: https://reviews.freebsd.org/D13133
Include ridx <-> rate conversion functions from rtwn(4) +
reuse already calculated value for ieee80211_radiotap(9).
Tested with Asus USB-N10, STA mode.
To accomodate all variaties of Pi DTS files floating around
we look for MAC address property either in DTS node for
USB ethernet (if it exists) or at predefined path
".../usb/hub/ethernet".
After r324184 smsc_fdt_find_eth_node started to return node
with compatibility string "usb424,ec00" as an eth node.
In imported GNU dts files this node still does not have
MAC address related property, and therefor following check for
"mac-address" and "local-mac-address" fails.
To make this logic more robust do not just search for the node
but also make sure it has required property, so if node with
accepted compatibility string exists but doesn't have the
property we fall back to looking for hardoded path mentioned above.
There should be no functional changes.
Reviewed by: hselasky
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D12670
- Added more compatibility strings to drivers not yet converted
- Added new RPI platform code compatibility string to match the ones used
upstream
- Adapted RPI and RPI2 DTS to match the new platform code compatibility
string
The goal is to use the upstream DTBs as a replacement for our custom one.
This is now possible with these changes.
Additionally, as the RPI firmware automatically chooses the right DTB for
us, this would allow to have one common armv6 kernel for RPI0 and RPI1
(BCM2835-based), and one common armv7 kernel for RPI2 v1.1 (BCM2836-based),
and RPI2 v1.2 / RPI3 (BCM2837-based).
Submitted by: Sylvain Garrigues <sylgar@gmail.com>
Differential Revision: https://reviews.freebsd.org/D12360
This patch adds hwtype parameter which keeps information about hardware
revision of Marvell EHCI controller. It allows to replace multiple
calls to ofw_bus_is_compatible with comparing hwtype value during driver
initialization.
Submitted by: Patryk Duda <pdk@semihalf.com>
Suggested by: ian
Obtained from: Semihalf
Sponsored by: Semihalf
This patch reuses ehci_mv driver by adding a support for the new
compatible string and adding ehci_mv.c to list of available options
for arm64 platforms.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12255
This driver will be used by Marvell Armada 3700 and 7k/8k SoC families.
The same, generic xhci device also appears in Armada 380, so we are reusing
driver.
This patch also adds xhci_mv.c entry to the arm64 files list.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12252
It turns out that this is more than a power optization. The OTG port
won't work on boards that have this property unless this setting is honored.
Also ensure that the usb phy device attaches before ehci.
programmed for infinite IN token retry after NAK, the SAF1761
hardware, however, does not retry the IN-token. This problem is
described in the SAF1761 errata, section 18.1.1.
While at it:
- Add some minor chip specific initialization for RTEMS.
- Add debug print for status registers in the interrupt filter.
Submitted by: Christian Mauderer <christian.mauderer@embedded-brains.de>
MFC after: 1 week
A long long time ago the register keyword told the compiler to store
the corresponding variable in a CPU register, but it is not relevant
for any compiler used in the FreeBSD world today.
ANSIfy related prototypes while here.
Reviewed by: cem, jhb
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D10193
left-click event. It can be disabled setting the new
hw.usb.wsp.enable_single_tap_clicks sysctl to 0.
Submitted by: K Staring <qdk@quickdekay.net>
Pull Request: https://github.com/freebsd/freebsd/pull/97
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
directly from the node.
- Use ni_txparms directly instead of calculating them manually every time
- Move M_EAPOL flag check upper; otherwise it may be skipped due to
'ucastrate' / 'mcastrate' check
- Use 'mgtrate' for control frames too (see ifconfig(8), mgtrate parameter)
- Add few more M_EAPOL checks where it was missing (zyd(4), ural(4),
urtw(4))
- Few unrelated cleanups
Tested with:
- Intel 6205 (iwn(4)), STA mode;
- WUSB54GC (rum(4)), HOSTAP mode + RTL8188EU (rtwn(4)), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9811
This change removes limitation of single S/G list entry and limitation on
maximal I/O size, using multiple data transfers per I/O if needed. Also
it removes code duplication between send and receive paths, which are now
completely equal.
for USB OTG-capable hardware to implement device side of USB
Mass Storage, ie pretend it's a flash drive. It's configured
in the same way as other CTL frontends, using ctladm(8)
or ctld(8). Differently from usfs(4), all the configuration
can be done without rebuilding the kernel.
Testing and review is welcome. Right now I'm still moving,
and I don't have access to my test environment, so I'm somewhat
reluctant to making larger changes to this code; on the other
hand I don't want to let it sit on Phab until my testing setup
is back, because I want to get it into 11.1-RELEASE.
Reviewed by: emaste (cursory), wblock (man page)
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8787
This enables the PHY circuitry for UTMI+ level 2 and 3, and sets the
flag to tell the ehci code that the root hub has a transaction translator
in it. For imx6 we can use the standard ehci_get_port_speed_portsc()
function to find out what speed device is connected to the port.
The tty layer uses tsw_busy to poll for busy/idle status of the transmitter
hardware during close() and tcdrain(). The ucom layer defines ULSR_TXRDY and
ULSR_TSRE bits for the line status register; when both are set, the
transmitter is idle. Not all chip drivers maintain those bits in the sc_lsr
field, and if the bits never get set the transmitter will always appear
busy, causing hangs in tcdrain().
These changes add a new sc_flag bit, UCOM_FLAG_LSRTXIDLE. When this flag is
set, ucom_busy() uses the lsr bits to return busy vs. idle state, otherwise
it always returns idle (which is effectively what happened before this
change because tsw_busy wasn't implemented).
For the uftdi chip driver, these changes stop masking out the tx idle bits
when processing the status register (because now they're useful), and it
calls ucom_use_lsr_txbits() to indicate the bits are maintained by the
driver and can be used by ucom_busy().
Differential Revision: https://reviews.freebsd.org/D9183
sure the XHCI controller is reset after halting it. The problem is
clearly a BIOS bug as the suspend and resume is failing without
loading the XHCI driver. The same happens when using Linux and the
XHCI driver is not loaded.
Submitted by: Yanko Yankulov <yanko.yankulov@gmail.com>
PR: 216261
MFC after: 1 week
Replace archaic "busses" with modern form "buses."
Intentionally excluded:
* Old/random drivers I didn't recognize
* Old hardware in general
* Use of "busses" in code as identifiers
No functional change.
http://grammarist.com/spelling/buses-busses/
PR: 216099
Reported by: bltsrc at mail.ru
Sponsored by: Dell EMC Isilon
These have been tested back-to-back with Linux 3.x and a similar attachment
at the other end; a CDC EEM-like encapsulation can be used for emulated
Ethernet over udbp(4) with ng_ether.
I don't yet know which RX descriptor bits map to shortgi, long-gi,
short-preamble, long-preamble, STBC, LDPC, HT40, etc - so I can't
easily add those just yet.
There's apparently no per-frame RX RSSI information exposed so we
also just use the results from the previous calibration task.
This also tidies up how the per-mbuf RSSI is pushed into the frame -
now that it's attached to the mbuf via rx_stats, we don't have to
do any silly hijinx to get it out of the frame processing path.
Tested:
* RTL8712, 1x1 cut 3, STA mode
boot panics in conjunction with the recently added EARLY_AP_STARTUP feature.
The panics happen due to using kernel facilities like callouts too early.
Tested by: jhb @
MFC after: 1 week
- Do not ignore initialization errors; call ieee80211_stop()
when initialization failed.
- Use usb_pause_mtx() instead of DELAY() while waiting for firmware
loading; this fixes system freeze during firmware startup.
- Do not execute rsu_stop() when device is powered off; fixes
'unknown board type (rfconfig=0xff)' error when the device is
reattached.
Tested with Asus USB-N10.
- Replace all remaining DPRINTF(N)'s with RSU_DPRINTF.
- Add new RSU_DEBUG_USB flag to track error codes returned by
usbd_do_request_flags().
- Improve few messages.
- Add partial promiscuous mode support (no management frames;
they cannot be received by the firmware and net80211 at the same time).
- Add monitor mode support (all frames).
Tested with Asus, USB-N10.
This is required for USB Rx aggregation
(and fixes 'could not allocate RX mbuf' / few other failures).
While here, reduce the number of Rx buffers from 100 to 1 -
the driver never uses more than one Rx buffer.
Tested with Asus USB-N10.
values. This more closely matches other wifi drivers in the tree.
The bitmap levels have been based closely on other drivers (primarily
[u]rtwn(4)) in the hope that one day these can be unified into a shared
wifi-debug framework.
This is the first step of several pieces of work I'm planning on doing
with the run(4) driver. I may well adjust and refine some of the debug
bitmaps at a later date.
Reviewed by: adrian, avos
Differential Revision: https://reviews.freebsd.org/D8704
This change includes firmware commands for key setup +
some additional checking via CAMREAD / CAMWRITE registers.
Nothing (except rsu_delete_key() for pairwise keys) is deferred;
to ensure that things are done in order rsu_set_key() will wait
until key deletion task will be finished.
Tested with Asus USB-N10 (all ciphers).
Differences from initial (reviewed) patch:
- Pause AC queues before disassociation - since CMD_DISCONNECT clears
crypto state all pending frames must be processed / dropped before it.
- Check sc_running flag before trying to set static keys.
- Clear key index from bitmap even when firmware command fails
(it will be invalidated via CAMWRITE anyway).
Reviewed by: adrian, kevlo
Tested by: kevlo
Differential Revision: https://reviews.freebsd.org/D8706
- Append RCR_APP_PHYSTS bit after firmware loading - otherwise
firmware will reset the register and this modification will be lost.
(without it Rx PHY descriptor section will contain garbage).
- Check if R92S_RXDW0_PHYST bit is set (like it is done in rtwn(4)) -
even if infosz is non-zero the section may not contain anything useful.
- In case, if descriptor is absent (A-MPDU?) use last calibrated RSSI
(rtwn(4) uses RSSI from the previous (sub)frame; probably, this
approach should be used here too).
Tested with Asus USB-N10, STA mode.
- Fill in Rx radiotap header correctly (for every packet in a chain;
not once per chain).
- Fix rate / flags fields in Rx radiotap.
- Add debug messages for discarded frames.
- Pass received control (< sizeof(struct ieee80211_frame)) frames
to net80211 (if allowed by device filter; cannot happen yet).
Tested with Asus USB-N10.
Differential Revision: https://reviews.freebsd.org/D5723
- Set IEEE80211_FEXT_SCAN_OFFLOAD flag; firmware can send null data
frames when associated.
- Check IEEE80211_SCAN_ACTIVE scan flag instead of IEEE80211_F_ASCAN
ic flag; the last is never set since r170530.
- Eliminate software scan (net80211) <-> site_survey (driver) race:
* override ic_scan_curchan and ic_scan_mindwell pointers so net80211
will not try to finish scanning automatically;
* inform net80211 about current status via ieee80211_cancel_scan()
and ieee80211_scan_done();
* remove corresponding workaround from rsu_join_bss().
Now the driver can associate to an AP with hidden SSID.
Tested with Asus USB-N10.
The directly following m_defrag() call can wait, so there is no reason this
call can't as well.
Reported by: Coverity
CID: 1353551
Sponsored by: Dell EMC Isilon
- Use ums lock as evdev lock
- Do not cap axes values to sysmouse limits for evdev reports
- Do not map T-axis events to buttons for evdev reports
- Use shortcuts for event reporting
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
MFC after: 1 week
When detaching device trees parent devices must be detached prior to
detaching its children. This is because parent devices can have
pointers to the child devices in their softcs which are not
invalidated by device_delete_child(). This can cause use after free
issues and panic().
Device drivers implementing trees, must ensure its detach function
detaches or deletes all its children before returning.
While at it remove now redundant device_detach() calls before
device_delete_child() and device_delete_children(), mostly in
the USB controller drivers.
Tested by: Jan Henrik Sylvester <me@janh.de>
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D8070
MFC after: 2 weeks
to ieee80211_add_rx_params() + drop last (ieee80211_rx_stats) parameter
Note: there is an additional check for ieee80211_get_rx_params()
return value (which does not exist in the original diff).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8207
- If check for net,ethernet/usb,device compatible node fails, try to find
.../usb/hub/ethernet, where ... is bus path that can depend on actual HW.
net,ethernet/usb,device compatibity strings are FreeBSD custom invention
that is used only in RPi DTBs and since there is no other way to tie USB
device to FDT node we just do our best effort here to work with upstream
device tree
- Use -1 value to indicate invalid phandle_t, 0 is valid phandle value and
shouldn't be used as error signal
This should have been committed in r307093: resource allocation depends
on source of the device tree. upstream dts has extra interrupt that we can
ignore
There are a variety of more interesting RX statistics that we should
keep track of but we don't. This is a starting point for adding more
information.
Specifically:
* now the RX rate information and some of the packet status is
passed up;
* The 32 bit or 64 bit TSF is passed up;
* the PHY mode is passed up;
* the "I'm decap'ed AMSDU!" state is passed up;
* number of RX chains is bumped to 4.
This is all mostly a placeholder for getting the data into the RX status
before we pass it up to net80211 - unfortunately we don't yet enforce
that drivers provide it, nor do we pass the provided info back up the
stack so anyone can use the data.
We're going to need to use some of this data moving forward.
Notably, now that some hardware can do AMSDU decap for us (the intel iwm
driver can do it when we flip it on; the ath10k port I'm doing does
it for us) then we need to pass it up through the stack so the duplicate
RX sequence numbers and crypto/IV details don't cause the packet to
be dropped and/or counted against a replay counter.
It's also the beginning of being able to do more interesting node
accounting in net80211. Specifically, once drivers start populating
per-packet rate information, AMPDU information, timestamps, etc,
we can start providing histograms of rate-versus-RSSI, account
for receive time spent per node and other such interesting things.
(Note: I'm also hoping to include ranging and RTT information for
future chipset support; and it's likely going to include it in
this kind of fashion.)
Replace various void * / int argument combinations with common structures:
- ieee80211_ratectl_tx_status for *_tx_complete();
- ieee80211_ratectl_tx_stats for *_tx_update();
While here, improve amrr_tx_update() for a bit:
1. In case, if receiver is not known (typical for Ralink USB drivers),
refresh Tx rate for all nodes on the interface.
2. There was a misuse:
- otus(4) sends non-decreasing counters (as originally intended);
- but ural(4), rum(4) and run(4) are using 'read & clear' registers
to obtain statistics for some period of time (and those 'last period'
values are used as arguments for tx_update()). If arguments are not big
enough, they are just discarded after the next call.
Fix: move counting into *_tx_update()
(now otus(4) will zero out all node counters after every tx_update() call)
Tested with:
- Intel 3945BG (wpi(4)), STA mode.
- WUSB54GC (rum(4)), STA / HOSTAP mode.
- RTL8188EU (urtwn(4)), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8037
- Convert "options EVDEV" to "device evdev" and "device uinput", add
modules for both new devices. They are isolated subsystems and do not
require any compile-time changes to general kernel subsytems
- For hybrid drivers that have evdev as an optional way to deliver input
events add option EVDEV_SUPPORT. Update all existing hybrid drivers
to use it instead of EVDEV
- Remove no-op DECLARE_MODULE in evdev, it's not required, MODULE_VERSION
is enough
- Add evdev module dependency to uinput
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Prepare for making evdev a module. "Pure" evdev device drivers (like
touchscreen) and evdev itself can be built as a modules regardless of
"options EVDEV" in kernel config. So if people does not require evdev
functionality in hybrid drivers like ums and ukbd they can, for instance,
kldload evdev and utouchscreen to run FreeBSD in kiosk mode.
Clear 'sc_calibrating' flag and stop calibration task when interface
is not associated; this fixes possible panic after detach.
Reported and tested by: hselasky
Reviewed by: adrian
MFC after: 6 days
event generation is disabled by default in favour of sysmouse. This
behavoiur is controlled by kern.evdev.rcpt_mask sysctl, bit 2 should
be set to give priority to hw over sysmouse
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Reviewed by: hans
Differential Revision: https://reviews.freebsd.org/D7863
event generation is disabled by default in favour of kbdmux. This
behavoiur is controlled by kern.evdev.rcpt_mask sysctl, bit 3 should
be set to give priority to hw over mux
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Reviewed by: hans
Differential Revision: https://reviews.freebsd.org/D7957
