VR_STICKHW register would result in unexpected results on these
hardwares. wpaul said the following for the issue.
The vr_attach() routine unconditionally does this for all supported
chips:
/*
* Windows may put the chip in suspend mode when it
* shuts down. Be sure to kick it in the head to wake it
* up again.
*/
VR_CLRBIT(sc, VR_STICKHW, (VR_STICKHW_DS0|VR_STICKHW_DS1));
The problem is, the VR_STICKHW register is not valid on all Rhine
devices. The VT86C100A chip, which is present on the D-Link DFE-530TX
boards, doesn't support power management, and its register space is
only 128 bytes wide. The VR_STICKHW register offset falls outside this
range. This may go unnoticed in most scenarios, but if you happen to have
another PCI device in your system which is assigned the register
space immediately after that of the Rhine, the vr(4) driver will
incorrectly stomp it. In my case, the BIOS on my test board decided
to put the register space for my PRO/100 ethernet board right next
to the Rhine, and the Rhine driver ended up clobbering the IMR register
of the PRO/100 device. (Long story short: the board kept locking up on
boot. Took me the better part of the morning suss out why.)
The strictly correct thing to do would be to check the PCI config space
to make sure the device supports the power management capability and only
write to the VR_STICKHW register if it does.
Instead of inspecting chip revision numbers for the availability of
VR_STICKHW register, check the existence of power management capability
of the hardware as wpaul suggested.
Reported by: wpaul
Suggested by: wpaul
OK'ed by: jhb
SAS-enabled cards. It also makes the driver MPSAFE, eliminating some
problems that resulted from CAM becoming MPSAFE. Many thanks to 3Ware/AMCC
for continuing to support FreeBSD.
Submitted by: Manjunath Ranganathaiah
Approved by: re
voltage of 0. This can result in a divide by zero trap. Add a guard
for this case. The value of lfcap is checked in acpi_battery_bif_valid()
just before this, so it is safe.
Reportd by: sam
Approved by: re
MFC after: 3 days
of directly from acpi0. Before it would attach prior to the sysresource
devices, causing the later allocation of its memory range to fail and
print a warning like "acpi0: reservation of fed00000, 1000 (3) failed".
Use an explicit define for our probe order base value of 10.
Help from: jhb
Tested by: Abdullah Ibn Hamad Al-Marri <almarrie / gmail.com>
MFC after: 3 days
Approved by: re
with all functions supported. This is done adding usb device IDs
to the table of recognised devices (because there is no standard
'scanner' class, so no other way to recognise them), and with
a small change to the uscanner attach routine that prevents
reconfiguring the whole USB device while we are dealing only with
one of its USB interfaces.
The latter part has been suggested by Steinar Hamre in
http://www.freebsd.org/cgi/query-pr.cgi?pr=107665 , i have
only added a bit of explaination to the code.
I have personally tried this on the Epson DX-5050 and DX-6000
devices (on the US market they have different names, CX-something).
I have good reasons to think that, possibly with the mere addition
of more USB ids to the table in uscanner.c, this should work with
all Epson multifunction devices in that family (from DX-3800 to
DX-7000 - these units are in the 50-120$ price range).
More details on related topics (SANE configuration, OCR, etc.)
at http://info.iet.unipi.it/~luigi/FreeBSD/dx5050.html
Manpage updates coming soon.
Approved by: re, imp
MFC after: 3 days
UDMA modes.
Please notice that Soekris NET5501 bios versions before 1.32f has a bug
that prevents this from working.
Approved by: re (gnn)
MFC: 2 weeks
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.
Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)
to gem_attach() as the former access softc members not yet initialized
at that time and gem_reset() actually is enough to stop the chip. [1]
o Revise the use of gem_bitwait(); add bus_barrier() calls before calling
gem_bitwait() to ensure the respective bit has been written before we
starting polling on it and poll for the right bits to change, f.e. even
though we only reset RX we have to actually wait for both GEM_RESET_RX
and GEM_RESET_TX to clear. Add some additional gem_bitwait() calls in
places we've been missing them according to the GEM documentation.
Along with this some excessive DELAYs, which probably only were added
because of bugs in gem_bitwait() and its use in the first place, as
well as as have of an gem_bitwait() reimplementation in gem_reset_tx()
were removed.
o Add gem_reset_rxdma() and use it to deal with GEM_MAC_RX_OVERFLOW errors
more gracefully as unlike gem_init_locked() it resets the RX DMA engine
only, causing no link loss and the FIFOs not to be cleared. Also use it
deal with GEM_INTR_RX_TAG_ERR errors, with previously were unhandled.
This was based on information obtained from the Linux GEM and OpenSolaris
ERI drivers.
o Turn on workarounds for silicon bugs in the Apple GMAC variants.
This was based on information obtained from the Darwin GMAC and Linux GEM
drivers.
o Turn on "infinite" (i.e. maximum 31 * 64 bytes in length) DMA bursts.
This greatly improves especially RX performance.
o Optimize the RX path, this consists of:
- kicking the receiver as soon as we've a spare descriptor in gem_rint()
again instead of just once after all the ready ones have been handled;
- kicking the receiver the right way, i.e. as outlined in the GEM
documentation in batches of 4 and by pointing it to the descriptor
after the last valid one;
- calling gem_rint() before gem_tint() in gem_intr() as gem_tint() may
take quite a while;
- doubling the size of the RX ring to 256 descriptors.
Overall the RX performance of a GEM in a 1GHz Sun Fire V210 was improved
from ~100Mbit/s to ~850Mbit/s.
o In gem_add_rxbuf() don't assign the newly allocated mbuf to rxs_mbuf
before calling bus_dmamap_load_mbuf_sg(), if bus_dmamap_load_mbuf_sg()
fails we'll free the newly allocated mbuf, unable to recycle the
previous one but a NULL pointer dereference instead.
o In gem_init_locked() honor the return value of gem_meminit().
o Simplify gem_ringsize() and dont' return garbage in the default case.
Based on OpenBSD.
o Don't turn on MAC control, MIF and PCS interrupts unless GEM_DEBUG is
defined as we don't need/use these interrupts for operation.
o In gem_start_locked() sync the DMA maps of the descriptor rings before
every kick of the transmitter and not just once after enqueuing all
packets as the NIC might instantly start transmitting after we kicked
it the first time.
o Keep state of the link state and use it to enable or disable the MAC
in gem_mii_statchg() accordingly as well as to return early from
gem_start_locked() in case the link is down. [3]
o Initialize the maximum frame size to a sane value.
o In gem_mii_statchg() enable carrier extension if appropriate.
o Increment if_ierrors in case of an GEM_MAC_RX_OVERFLOW error and in
gem_eint(). [3]
o Handle IFF_ALLMULTI correctly; don't set it if we've turned promiscuous
group mode on and don't clear the flag if we've disabled promiscuous
group mode (these were mostly NOPs though). [2]
o Let gem_eint() also report GEM_INTR_PERR errors.
o Move setting sc_variant from gem_pci_probe() to gem_pci_attach() as
device probe methods are not supposed to touch the softc.
o Collapse sc_inited and sc_pci into bits for sc_flags.
o Add CTASSERTs ensuring that GEM_NRXDESC and GEM_NTXDESC are set to
legal values.
o Correctly set up for 802.3x flow control, though #ifdef out the code
that actually enables it as this needs more testing and mainly a proper
framework to support it.
o Correct and add some conversions from hard-coded functions names to
__func__ which were borked or forgotten in if_gem.c rev. 1.42.
o Use PCIR_BAR instead of a homegrown macro.
o Replace sc_enaddr[6] with sc_enaddr[ETHER_ADDR_LEN].
o In gem_pci_attach() in case attaching fails release the resources in
the opposite order they were allocated.
o Make gem_reset() static to if_gem.c as it's not needed outside that
module.
o Remove the GEM_GIGABIT flag and the associated code; GEM_GIGABIT was
never set and the associated code was in the wrong place.
o Remove sc_mif_config; it was only used to cache the contents of the
respective register within gem_attach().
o Remove the #ifdef'ed out NetBSD/OpenBSD code for establishing a suspend
hook as it will never be used on FreeBSD.
o Also probe Apple Intrepid 2 GMAC and Apple Shasta GMAC, add support for
Apple K2 GMAC. Based on OpenBSD.
o Add support for Sun GBE/P cards, or in other words actually add support
for cards based on GEM to gem(4). This mainly consists of adding support
for the TBI of these chips. Along with this the PHY selection code was
rewritten to hardcode the PHY number for certain configurations as for
example the PHY of the on-board ERI of Blade 1000 shows up twice causing
no link as the second incarnation is isolated.
These changes were ported from OpenBSD with some additional improvements
and modulo some bugs.
o Add code to if_gem_pci.c allowing to read the MAC-address from the VPD on
systems without Open Firmware.
This is an improved version of my variant of the respective code in
if_hme_pci.c
o Now that gem(4) is MI enable it for all archs.
Pointed out by: yongari [1]
Suggested by: rwatson [2], yongari [3]
Tested on: i386 (GEM), powerpc (GMACs by marcel and yongari),
sparc64 (ERI and GEM)
Reviewed by: yongari
Approved by: re (kensmith)
polling/interrupt-driven fallback and instead use polling only during
boot and pure interrupt-driven mode after boot. Polled mode could be
relegated completely to a legacy role if we could enable interrupts
during boot. Polled mode can be forced after boot by setting
debug.acpi.ec.polled="1", i.e. if there are timeouts.
- Use polling only during boot, shutdown, or if requested by the user.
Otherwise, use a generation count of GPEs, incremented atomically. This
prevents an old status value from being used if the EC is really slow
and the same condition (i.e. multiple IBEs for a write transaction) is
being checked.
- Check for and run the query handler directly if the SCI bit is set in
the status register during boot. Previously, the query handler wouldn't
run until interrupts were finally enabled late in boot.
- During boot and after starting a command, check if the event appears
to already have occurred before we even start waiting. If so, it's
possible the EC is very slow and we might accept an old status value.
Print a warning in this case. Once we've booted, interrupt-driven mode
should work just fine but polled mode could be unreliable. There's not
much more we can do about this until interrupts are enabled during boot.
- In the above case, we also do one final check if the interrupt-driven
mode gets a timeout. If the status is complete, it will force the
system back into polled mode since interrupt mode doesn't work. For
polled mode during boot, if the status appears to be already complete
before beginning the check loop, it waits 10 us before actually checking
the status, just in case the EC is really slow and hasn't gotten to work
on the new request yet.
- Use upper-case hex for the _Qxx method
- Use device_printf for errors, don't hide them under verbose
- Increase default total timeout to 750 ms and decrease polling interval
to 5 us.
- Don't pass the status value via the softc. Just read it directly.
- Remove the mutex. We use the sx lock for transaction serialization
with the query handler.
- Remove the Intel copyright notice as no code of theirs was ever
present in this file (verified against rev 1.1)
- Allow KTR module-only builds for ease of testing
Thanks to jkim and Alexey Starikovskiy for helpful discussions and testing.
Approved by: re
MFC after: 2 weeks
- The output routine of low level console is not protected by any lock
by default.
- Increment and decrement of sc->write_in_progress are not atomic and
this may cause console hang.
- We also have many other states used by emulator that should be protected
by the lock.
- This change does not fix interspersed messages which PRINTF_BUFR_SIZE
kernel option should fix.
Approved by: re (bmah)
MFC after: 1 week
controller if it's sole child device has the "usb" device class.
Previously ehci(4) would think that PCI-ISA bridges on the same slot
(such as in some Intel ICHs) were "neighbors" resulting in spurious
warnings about neighbor count mismatches.
- Fix a memory leak when looking for neighbors.
MFC after: 1 week
Approved by: re (kensmith)
Tested by: phk
to become unkillable when that process is sent a termination signal. The
process will sit in waitvt looping in the kernel, and chewing up all
available CPU until the system is rebooted.
Submitted by: Jilles Tjoelker <jilles@stack.nl>
Reviewed by: bde
Approved by: re (kensmith)
MFC after: 1 week
the mfi(4) LSI MegaSAS RAID card. Looking at the Linux driver for the
mpt(4) it should be 0x0062 and not 0x0060. Tested with an mfi card
of this device id.
Approved by: re (bmah)
Reviewed by: scottl
MFC after: 3 days
o add driver callback to handle notification of beacon changes;
this is required for devices that manage beacon frames themselves
(devices must override the default handler which does nothing)
o move beacon update-related flags from ieee80211com to the beacon
offsets storage (or handle however a driver wants)
o expand beacon offsets structure with members needed for 11h/dfs
and appie's
o change calling convention for ieee80211_beacon_alloc and
ieee80211_beacon_update
o add overlapping bss support for 11g; requires driver to pass
beacon frames from overlapping bss up to net80211 which is not
presently done by any driver
o move HT beacon contents update to a routine in the HT code area
Reviewed by: avatar, thompsa, sephe
Approved by: re (blanket wireless)
does not have a rate table in older hal's so if we scan such a
channel the driver will hit an assertion or crash; for old hal's
fallback to using the static turbo rate table for this mode
(not correct but good enough for now given none of the rate
control algorithms understand how to switch between base+boost)
Approved by: re (blanket wireless)
mode works properly, previously the hostap channel could not be changed off #3.
Fix an ifp/sc misuse while I am here.
Reported by: many
Approved by: re (bmah)
change interrupt if the link is established with link parter. However
interrupt handler didn't acknowledge the interrupt if nfe(4) was not
running at the time of interrupt delivery. This caused endless
interrupt generation. Fix the bug by acknowledging the interrupt
regardless of running state of the driver.
PR: kern/116295
Submitted by: Mark Derbyshire (mark At taom dot com)
Approved by: re (kensmith)
other changes too).
(without any real order)
1. Use device_get_nameunit for mutex naming
2. Add timer for low-latency playback
3. Move most mixer controls from sysctls to mixer(8) controls.
This is a largest part of this patch.
4. Add analog/digital switch (as a temporary sysctl)
5. Get back support for low-bitrate playback (with help of (2))
6. Change locking for exclusive I/O. Writing to non-PTR register
is almost safe and does not need to be ordered with PTR operations.
7. Disable MIDI until we get it to detach properly and fix memory
managment problems.
8. Enable multichannel playback by default. It is as stable as
single-channel mode. Multichannel recording is still an
experimental feature.
9. Multichannel options can be changed by loader tunables.
10. Add a way to disable card from a loader tunable.
11. Add new PCI IDs.
12. Debugger settings are loader tunables now.
14. Remove some unused variables.
15. Mark pcm sub-devices MPSAFE.
16. Partially revert (bus_setup_intr -> snd_setup_intr) since it need
to be done independently
Submitted by: Yuriy Tsibizov (driver maintainer)
Approved by: re (bmah)
- duplicate #define in header, thanks to Kevin Lo for pointing out.
- incorrect BUSMASTER enable logic, thanks Patrick Oeschger
- 82543 fails due to bogus IO BAR logic
- Allow 82571 to use MSI interrupts
- Checksum Offload for UDP not working on 82575
Approved by:re
ioctl().
Note that other information provided by ifconfig(8) such like "list chan"
or "list ap" are still not available at this moment.
Before an(4) is connected to wlan(4), users are encouraged to use
ancontrol(8) to retrieve aforementioned information.
Reported by: dhw (http://lists.freebsd.org/pipermail/freebsd-current/2007-July/074848.html)
Reviewed by: ambrisko
Tested by: dhw
Approved by: re (bmah)
- fix the use after free seen when sending packets small enough to fit as an immediate
and bpf peers are present
- update to firmware rev 4.7 along with various small vendor fixes
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 3 days
that can lead to a panic when the stick is yanked.
- make sure that zyd_attach() returns 0 or errno.
Submitted by: Weongyo Jeong <weongyo.jeong@gmail.com>
Reported by: Ted Lindgreen <ted@tednet.nl>
Reviewed by: sam
Approved by: re (blanket wireless)
o update ic_lastdata to reflect time of last outbound frame
o outbound traffic must preempt/cancel bg scanning to avoid delays
This stuff was somehow missed in the initial import.
Reviewed by: thompsa, avatar, sephe (earlier version)
Approved by: re (blanket wireless)
The first drop was Beta, this code is expected to be the release version.
Note that this driver code will build in either 6.2 or 7. If you
use the code in 6.2 you will not get TSO or MSI/X support but it will
function in a legacy mode.
Approved by: re
needed at least to convince the BIOS to give us access to CPU freq
control on MacBooks.
Submitted by: Rui Paulo <rpaulo / fnop.net>
Approved by: re
MFC after: 5 days
ZD1211/ZD1211B USB IEEE 802.11b/g wireless network devices. Not (yet)
connected to the build process (next batch of commits once I've looped
the current back back).
Submitted by: Weongyo Jeong
Reviewed by: sam@
Approved by: re@
Both WWNN and WWPN are 64-bit unsigned integers and they are prefixed
with "0x", which requires two more bytes each.
Submitted by: Danny Braniss (danny at cs dot huji dot ac dot il)
via Matthew Jacob (lydianconcepts at gmail dot com)
Approved by: re (bmah)
MFC after: 3 days
