In fdformat.c a closing parenthesis is at the wrong place. Instead of
adding sizeof _PATH_DEV + 1 to the length of argv[optind], the length of the
string starting (sizeof _PATH_DEV + 1) characters after argv[optind]'s
beginning (accessing junk memory if we jump over the terminating null
character) is passed to malloc().
PR: bin/60026
Submitted by: Stefan Farfeleder <stefan@fafoe.narf.at>
changes in the userland utilities. For fdcontrol(8), i now finally
keep my promise made more than 7 years ago that ``the fdcontrol
utility is currently under development and the user interface will
likely change''. :-)
. The main device node now supports automatic density selection for
commonly used media densities. So you can stuff your 1.44 MB and
720 KB media into your drive and just access /dev/fd0, no questions
asked. It's all that easy, isn't it? :)
. Device density handling has been completely overhauled. The old way
of hardwired kernel density knowledge is no longer there. Instead,
the kernel now implements 16 subdevices per drive. The first
subdevice uses automatic density selection, while the remaining 15
devices are freely programmable. They can be assigned an arbitrary
name of the form /dev/fd[:digit]+.[:digit:]{1,4}, where the second
number is meant to either implement device names that are mnemonic
for their raw capacity (as it used to be), or they can alternatively
be created as "anonymous" devices like fd0.1 through fd0.15,
depending on the taste of the administrator. After creating a
subdevice, it is initialized to the maximal native density of the
respective drive type, so it needs to be customized for other
densities by using fdcontrol(8). Pseudo-partition devices (fd0a
through fd0h) are still supported as symlinks.
. The old hack to use flags 0x1 to always assume drive 0 were there is
no longer supported; this is now supposed to be done by wiring the
devices down from the loader via device flags. On IA32
architectures, the first two drives are looked up in the CMOS
configuration records though. On PCMCIA (i. e., the Y-E Data
controller of the Toshiba Libretto), a single drive is always
assumed.
. Other specialities like disabling the FIFO and not probing the drive
at boot-time are selected by per-controller or per-drive flags, too.
. Unit attentions (media has been changed) are supposed to be detected
now; density autoselection only occurs after a unit attention. (Can
be turned off by a per-drive flag, this will cause each Fdopen() to
perform the autoselection.)
. FM floppies can be handled now (on controllers that actually support
it -- not all do these days).
. Fdopen() can be told to avoid density selection by setting
O_NONBLOCK; this leaves the descriptor in a half-opened state where
only a few ioctls are accepted. This is necessary to run fdformat
on a device that uses automatic density selection (since you cannot
autoselect on an unformatted medium, obviously).
. Just differentiate between a plain old NE765 and the enhanced chips,
but don't try more; the existing code was wrong and only misdetected
the chips anyway.
BUGS and TODOs:
. All documentation update still needs to be done.
. Formatting not-so-standard format yields unpredictable results; i
have yet to figure out why this happens. "Standard" formats like
720 and 1440 KB do work, however.
. rc scripts are needed to setup device nodes with nonstandard
densities (like the old /dev/fdN.MMM we used to have).
. Obtaining device flags from the kernel environment doesn't work yet,
thus currently only drives that are present in (IA32) CMOS are
really detected. Someone who knows the odds and ends about device
flags is needed here, i can't figure out what i'm doing wrong.
. 2.88 MB still needs to be done.
Avoid using parenthesis enclosure macros (.Pq and .Po/.Pc) with plain text.
Not only this slows down the mdoc(7) processing significantly, but it also
has an undesired (in this case) effect of disabling hyphenation within the
entire enclosed block.
give a bit more information about up to 10 errors encountered during
formatting (unless -q has been specified, of course).
While being here, removed a bitrotten comment in the Makefile, and
kill the old Emacs local variable stuff at the end of fdformat.c
that's no longer useful anway.
avoid blasting the syslog with error messages from bad floppies. Both
tools have their own error reporting anyway (which could easily be
cluttered by the syslog output on your terminal).
has been made obsolete by the block/char device merging.
Reflect this change in the manual page and fix the usage of a
backslash in ``e.g.''.
Reviewed by: bright, sheldonh, phk
track.
The Id line is normally at the bottom of the main comment block in the
man page, separated from the rest of the manpage by an empty comment,
like so;
.\" $Id$
.\"
If the immediately preceding comment is a @(#) format ID marker than the
the $Id$ will line up underneath it with no intervening blank lines.
Otherwise, an additional blank line is inserted.
Approved by: bde
Message-Id: <9402201119.AA06430@login.dkuug.dk>
Subject: bug in fdformat.c
There is a bug in fdformat.c: the number of heads are hardcoded in two places.
This is quite inconsequencial at present, but a bug nontheless.
