By using DWC TRM terminology, normal descriptor format should be named
extended and alternate descriptor format should be named normal.
Should not been functional change.
MFC after: 4 weeks
Don't set initial voltage for regulators having their voltage already
in allowed range. As side effect of this change, we don't try to set
initial voltage for fixed voltage regulators - these don't have impemented
voltage set method so their initialization has always failed.
MFC after: 3 weeks
- always initialize selector of voltage signaling standard.
Various versions of U-boot leaves voltage signaling standard settings
for PMUIO2 domain in different state. Always initialize it
into expected state.
- start the driver as early as possible, the IO domains should be
initialized before other drivers are attached.
- rename RK3399 register to its name founds in TRM.
This is the second part of fixes for serial port corruption observed after
DT 5.6 import.
Reviewed by: manu
MFC after: 1 week
Store the attached regulator in a tailq to later find them in ofw_map.
While here, do not attempt to attach a regulator without a name, a node
might exists but if it doesn't have a name the regulator is unused.
MFC after: 1 month
If pin is switched from fixed function to GPIO, it should have prepared
direction, pull-up/down and default value before function gets switched.
Otherwise we may produce unwanted glitch on output pin.
Right order of drive strength settings is questionable, but I think that
is slightly safer to do it also before function switch.
This fixes serial port corruption observed after DT 5.6 import.
MFC after: 1 week
The TSADC familiy is a little bit more complex than V2 and V3.
Early revision do not use syscon and do not use qsel (RK3288).
Next revision still do not use syscon but uses qsel (RK3328).
Final revision use both.
Submitted by: peterj
MFC after: 1 month
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Approved by: kib (mentor, blanket)
Differential Revision: https://reviews.freebsd.org/D23635
If a regulator is already enabled, do not set its value to the minimum
supported on the board.
This fixes booting on rock64 where we set some regulator to the minimal value
while the IPs needs more based on what the bootloader configured.
MFC after: 1 week
This method will set the desired voltaged based on values in the DTS.
It will not enable the regulator, this is the job of either a consumer
or regnode_set_constraint SYSINIT if the regulator is boot_on or always_on.
Reviewed by: mmel
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D23216
The gpio controller in rockchips SoC in a child of the pinctrl driver
and cannot control pullups and pulldowns.
Use the new fdt_pinctrl interface for accessing pin capabilities and
setting them.
We can now report that every pins is capable of being IN or OUT function
and PULLUP PULLDOWN.
If the pin isn't in gpio mode no changes will be allowed.
Reviewed by: ganbold (previous version)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D22849
The two switch regulator are always 3.0V.
Add a special case in get_voltage that if min=max we directly
return the value without calculating it.
Reviewed by: mmel
Differential Revision: https://reviews.freebsd.org/D23004
This driver configure the registers in the GRF according to the value
of the regulators for the platform.
Some IP can run with either 3.0V or 1.8V, if we don't configure them
correctly according to the external voltage used they will not work.
It's only done at boot time for now and might be needed at runtime for
IP like sdmmc.
Reviewed by: mmel
Tested On: RockPro64, Firefly-RK3399 (gonzo), AIO-3288 (mmel)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D22854
The RK808 driver was missing the LDO and switch regulators.
Add support for them.
Reviewed by: mmel
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D22852
The maxpin counter starts at 0, fix one by one error.
This is still not totally correct for some banks in some SoC that have
fewer pins but this will be dealt with in another commit.
MFC after: 3 days
r351187 change the SYSCON_WRITE to SYSCON_MODIFY but didn't changed the
mask variable that used to hold the bitmask in the upper 16 bits of the
register that control which bits are changed. So we ended up clearing
bit from the upper 16bits half which are always 0 after a read.
Use the correct bit mask for bits that we want to clear.
MFC after: 3 days
Unfortunately, there are some limitations:
- memory aperture of his controller is only 16MiB, so it is nearly
unusable for graphic cards
- every attempt to generate type 1 config cycle always causes trap.
These config cycles are disabled now and we don't support cards
with PCIe switch.
- in some cases, attempt to do config cycle to (probably) not-yet ready
card also causes trap. This cannot be detected at runtime, but it seems
like very rare issue.
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D22724
Only bank 0 and bank 2 are different than other rockchip SoC, fix this.
While here remove some debug printfs that where added in r355648
MFC after: 3 days
X-MFC-With: r355648
Those clocks are always enable by default and are not really explained
in the TRM but the reason we had them is that they have the periph clock
as a parent and those parent should never be disable which can happen
if we disable all the childs. The current childs are the sd/emmc/sdio clocks
so the board will hang if we disable them.
MFC after: 1 month
RK3399 PLLs have three modes :
- Normal, where they behave normally and their freq is calculated based on
the registers values.
- Slow, where the PLL freq is 24Mhz (well, the external oscillator).
- Deep Slow, used for suspend where the freq is 32Khz.
We used to put every CPU related PLL in normal mode but it can cause problem
if the firmware didn't setup the clocks register correctly.
And even if it did but left the pll in slow or deep slow mode that might be
because the PMIC suppling voltage for the CPU haven't been configured yet
and we cannot do that at this point.
So remove the ability to set PLLs to normal mode at boot to avoid any problems.
- implement of all but mmc clocks. MMC clocks will be added later by own commit.
- use 'link' clock type for external clocks.
- use macros for initialization of structure's named members.
MFC after: 3 weeks
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D22441
- add support for log2 based dividers
- use proper write mask when writing to divider register
MFC after: 3 weeks
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D22283
- add support for fractional dividers
- allow to declare fixed and linked clock
MFC after: 3 weeks
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D22282
This function will call the regnode_check_voltage method for a given regulator
and check if the desired voltage in reachable by it.
Also adds a default method that check the std_param and which should be enough
for most regulators and add it as the method for axp* rk805 and fixed regulators.
Reviewed by: mmel
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D22260
Declare retry in the function scope.
Rename it to retry as there is a timeout function which was
causing to code to compile.
Reported by: jhibbits
MFC after: 1 month
X-MFC-WITH: r354089
The RK805 regs array was being allocated before it's required size was
known, causing the driver to use memory it didn't own. That memory
was subsequently allocated and used elsewhere causing later fatal data
aborts in rk805_map().
Whilst I'm here, add a sanity check to catch unsupported PMICs (this
shouldn't ever get hit because the probe should have failed).
Reviewed by: manu
MFC after: 1 week
Sponsored by: Google
This is a driver for the USB3 PHY present in the RK3399.
While the phy support DP (Display Port) the driver doesn't has we have
no driver to test this with for now.
All the lane and pll configuration is just magic values from rockchip.
While the manual have some info on those registers it's really hard to
understand how to calculate those values (if there is a way).
MFC after: 1 month
We only support host mode so those functions are just added so
we won't panic when generic-{e,o}hci will set the phy to host mode.
MFC after: 1 month
X-MFC-With: r353062
This driver is for the usb phy present on rockchip SoC.
It only support RK3399 and host mode for now.
The driver expose the usb clock needed by the usb controller.
