Introduce some functions to map NIC ring indexes into netmap ring
indexes and vice versa. This way we can implement the bound
checks only in one place (and hopefully in a correct way).
On passing, make the code and comments more uniform across the
various drivers.
- remove experimental code for disabling CRC
- use the correct constant for conversion between interrupt rate
and EITR values (the previous values were off by a factor of 2)
- make dev.ix.N.queueM.interrupt_rate a RW sysctl variable.
Changing individual values affects the queue immediately,
and propagates to all interfaces at the next reinit.
- add dev.ix.N.queueM.irqs rdonly sysctl, to export the actual
interrupt counts
Netmap-related changes for ixgbe:
- use the "new" format for TX descriptors in netmap mode.
- pass interrupt mitigation delays to the user process doing poll()
on a netmap file descriptor.
On the RX side this means we will not check the ring more than once
per interrupt. This gives the process a chance to sleep and process
packets in larger batches, thus reducing CPU usage.
On the TX side we take this even further: completed transmissions are
reclaimed every half ring even if the NIC interrupts more often.
This saves even more CPU without any additional tx delays.
Generic Netmap-related changes:
- align the netmap_kring to cache lines so that there is no false sharing
(possibly useful for multiqueue NICs and MSIX interrupts, which are
handled by different cores). It's a minor improvement but it does not
cost anything.
Reviewed by: Jack Vogel
Approved by: Jack Vogel
1. correct the initialization of RDT when there is an ixgbe_init()
while a netmap client is active. This code was previously
in ixgbe_initialize_receive_units() but RDT is overwritten
shortly afterwards in ixgbe_init_locked()
2. add code (not active yet) to disable CRCSTRIP while in netmap mode.
From all evidence i could gather, it seems that when the 82599 has to
write a data block that is not a full cache line, it first reads
the line (64 bytes) and then writes back the updated version.
This hurts reception of min-sized frames, which are only 60 bytes
if the CRC is stripped: i could never get above 11Mpps
(received from one queue) with CRCSTRIP enabled, whyle 64+4-byte
packets reach 14.2 Mpps (the theoretical maximum).
Leaving the CRC in gets us 14.88Mpps for 60+4 byte frames,
(and penalizes 64+4). The min-size case is important not just because
it looks good in benchmarks, but also because this is the size
of pure acks.
Note we cannot leave CRCSTRIP on by default because it is
incompatible with some other features (LRO etc.)
the memory allocator used by netmap. No functional change,
two small bug fixes:
- in if_re.c add a missing bus_dmamap_sync()
- in netmap.c comment out a spurious free() in an error handling block
- {ixgbe,ixv}_header_split is passed to TUNABLE_INT, so delcare it
int, not bool.
- {ixgbe,ixv}_tx_ctx_setup() returns a boolean value, so declare it
bool, not int.
- {ixgbe,ixv}_tso_setup() returns a bool, so declare it bool, not boolean_t.
- {ixgbe,ixv}_txeof() returns a bool, so declare it bool, not boolean_t.
- Do not re-define bool if the symbol already exists.
MFC after: 2 weeks
Sponsored by: Isilon Systems, LLC
A link reset now is completely transparent for the netmap client:
even if the NIC resets its own ring (e.g. restarting from 0),
the client will not see any change in the current rx/tx positions,
because the driver will keep track of the offset between the two.
2. make the device-specific code more uniform across different drivers
There were some inconsistencies in the implementation of the netmap
support routines, now drivers have been aligned to a common
code structure.
3. import netmap support for ixgbe . This is implemented as a very
small patch for ixgbe.c (233 lines, 11 chunks, mostly comments:
in total the patch has only 54 lines of new code) , as most of
the code is in an external file sys/dev/netmap/ixgbe_netmap.h ,
following some initial comments from Jack Vogel about making
changes less intrusive.
(Note, i have emailed Jack multiple times asking if he had
comments on this structure of the code; i got no reply so
i assume he is fine with it).
Support for other drivers (em, lem, re, igb) will come later.
"ixgbe" is now the reference driver for netmap support. Both the
external file (sys/dev/netmap/ixgbe_netmap.h) and the device-specific
patches (in sys/dev/ixgbe/ixgbe.c) are heavily commented and should
serve as a reference for other device drivers.
Tested on i386 and amd64 with the pkt-gen program in tools/tools/netmap,
the sender does 14.88 Mpps at 1050 Mhz and 14.2 Mpps at 900 MHz
on an i7-860 with 4 cores and 82599 card. Haven't tried yet more
aggressive optimizations such as adding 'prefetch' instructions
in the time-critical parts of the code.
The current code was rounding down the maximum frame size instead of
routing up, resulting in a read size of 1024 bytes, in the non-jumbo
frame case, and splitting the packets across multiple mbufs.
Consequently the above problem exposed another issue, which is when
packets were splitted across multiple mbufs, and all of the mbufs in the
chain have the M_PKTHDR flag set.
Submitted by: original patch by Ray Ruvinskiy at BlueCoat dot com
Reviewed by: jfv, kmacy, rwatson
Approved by: re (rwatson)
MFC after: 5 days
crusty, and this still isn't perfect, but its at least a bit
more recent.
Secondly, a few improvements to the driver from Andrew Boyer,
support hint to allow devices to not attach, add VLAN_HWTSO
capability so vlans can use TSO, fix in the interrupt handler
to make sure the stack TX queue is processed. Oh, and also
make sure IPv6 does not cause a re-init in the ioctl routine.
Thanks for your efforts Andrew!
Thanks to Claudio Jeker for noticing the ixgbe_xmit() routine
was not correctly swapping the dma map from the first to the
last descriptor in a multi-descriptor transmission, corrected
this.
- Also a couple minor tweaks to the TX code from the same source.
- Add the INET ioctl code which has been missing from this driver,
and which caused IP aliases to reset the interface.
- Last, some minor logic changes that just reflect upcoming
hardware support, but have no other functional effect now.
MFC after a week
CRITICAL FIX - with stats changes the older 82598 will panic
and trash the stack on driver load, FCOE registers ONLY exist
in 82599 and must not be read otherwise.
kern/153951 - to correct incorrect media type on adapters
with pluggable modules I have eliminated the old static
table in favor of a new dynamic shared code routine. This
also has the benefit of detecting changes when a different
module is inserted.
Performance/enhancement to the Flow Director code from my
linux coworker (the developer of the code).
Fixes from Michael Tuexen - a data corruption problem on the
82599 (CRITICAL), fix so the buf size correctly adjusts as
the cluster changes, and max descriptors are set properly.
Also added 16K clusters for those REALLY big jumbos :)
In the RX path, the RX LOCK was not being released, and this
causes LOR problems. Add the code that igb already has.
Sync with in house shared code, this was necessary for the
Flow Director fix.
MFC in 2 days
finding. The test to compare the mbuf m_len against
a fixed value and then returning needs to be removed.
When using VLANS and doing HW_TAGGING, and IPV6, the
ICMP6 packets actually fail this condition, the constant
assumes that the tag is IN the frame, and its not, so
the length is actually tiny. Furthermore, I'm not sure
what the point was to just return??
MFC after: 3 days
- This adds a VM SRIOV interface, ixv, it is however
transparent to the user, it links with the ixgbe.ko,
but when ixgbe is loaded in a virtualized guest with
SRIOV configured this will be detected.
- Sync shared code to latest
- Many bug fixes and improvements, thanks to everyone
who has been using the driver and reporting issues.
configuration function. For failed memory allocations, em(4)/lem(4)
called panic(9) which is not acceptable on production box.
igb(4)/ixgb(4)/ix(4) allocated the required memory in stack which
consumed 768 bytes of stack memory which looks too big.
To address these issues, allocate multicast array memory in device
attach time and make multicast configuration success under any
conditions. This change also removes the excessive use of memory in
stack.
Reviewed by: jfv
limit the advertised speed of an SFP+ to 1G, effectively
"forcing" link at that lower speed. It is off by default
and is enabled by sysctl dev.ix.0.force_gig=1, 0 will
set it back to the norm.
doing bidirectional stress traffic on 82598.
Also a couple bug fixes from Michael Tuexen, thank you!!
Add a workaround into the header so that 8 REL can use
the driver (adds local copy of ALTQ fix).
MFC: in a few days
When not defining header split do not allocate mbufs,
this can be a BIG savings in the mbuf memory pool.
Also keep seperate dma maps for the header and
payload pieces when doing header split. The basis
of this code was a patch done a while ago by
yongari, thank you :)
A number of white space changes.
MFC: in a few days
- add a moderation value to the Link vector
- allow disabling HW RSC on the 82599 if LRO
is not enabled.
- correct error in the stats code
- change optic type on the 82598 DA device
Thanks to Andrew Boyer for the changes.
no flowid is present, this was causing some bad
reordering, now just use 0.
Also, add a few watchdog bits, and tx handler bits
that were corrected in igb.
also for finding a one character bug that kept TSO from working.
Sometimes with direct attach cables a failure can occur in init,
the old method of calling detach was broken, there is no way to
return an error to the system from init, so I have changed it to
return failure thru the ioctl.
And, have fixed the ALTQ code changes of Max Laier, sorry Max :)
- add some new hardware support for 82599
- Big change to interrupt architecture, it now
uses a queue which contains an RX/TX pair as
the recipient of the interrupt. This will reduce
overall system interrupts/msix usage.
- Improved RX mbuf handling: the old get_buf routine
is no longer synchronized with rxeof, this allows
the elimination of packet discards due to mbuf
allocation failure.
- Much simplified and improved AIM code, it now
happens in the queue interrupt context and takes
into account both the traffic on the RX AND TX
side.
- variety of small tweaks, like ring size, that have
been seen as performance improvements.
- Thanks to those that provided feedback or suggested
changes, I hope I've caught all of them.
- introduce drbr_needs_enqueue that returns whether the interface/br needs
an enqueue operation: returns true if altq is enabled or there are
already packets in the ring (as we need to maintain packet order)
- update all drbr consumers
- fix drbr_flush
- avoid using the driver queue (IFQ_DRV_*) in the altq case as the
multiqueue consumer does not provide enough protection, serialize altq
interaction with the main queue lock
- make drbr_dequeue_cond work with altq
Discussed with: kmacy, yongari, jfv
MFC after: 4 weeks
This adds new feature support for the 82599, a hardware
assist to LRO, doing this required a large revamp to the
RX cleanup code because the descriptor ring may not be
processed out of order, this necessitated the elimination
of global pointers.
Additionally, the RX routine now does not refresh mbufs
on every descriptor, rather it will do a range, and then
update the hardware pointer at that time. These are
performance oriented changes.
The TX side now has a cleaner simpler watchdog algorithm
as well, in TX cleanup a read of ticks is stored, that
can then be compared in local_timer to determine if
there is a hang.
Various other cleanups along the way, thanks to all who
have provided input and testing.
