the queue where to enqueue pages that are going to be unwired.
- Add stronger checks to the enqueue/dequeue for the pagequeues when
adding and removing pages to them.
Of course, for unmanaged pages the queue parameter of vm_page_unwire() will
be ignored, just as the active parameter today.
This makes adding new pagequeues quicker.
This change effectively modifies the KPI. __FreeBSD_version will be,
however, bumped just when the full cache of free pages will be
evicted.
Sponsored by: EMC / Isilon storage division
Reviewed by: alc
Tested by: pho
portsnap extract, where previously it would panic.. clearly someone
who knows pmap should optimize this code per alc's comment...
Submitted by: alc
MFC after: probably
In particular, don't check the value of the bus_dma map against NULL
to determine if either bus_dmamem_alloc() or bus_dmamap_load() succeeded.
Instead, assume that bus_dmamap_load() succeeeded (and thus that
bus_dmamap_unload() should be called) if the bus address for a resource
is non-zero, and assume that bus_dmamem_alloc() succeeded (and thus
that bus_dmamem_free() should be called) if the virtual address for a
resource is not NULL.
In many cases these bugs could result in leaks when a driver was detached.
Reviewed by: yongari
MFC after: 2 weeks
don't create a map before calling bus_dmamem_alloc() (such maps were
leaked). It is believed that the extra destroy of the map was generally
harmless since bus_dmamem_alloc() often uses special maps for which
bus_dmamap_destroy() is a no-op (e.g. on x86).
Reviewed by: scottl
a partially populated reservation becomes fully populated, and decrease this
field when a fully populated reservation becomes partially populated.
Use this field to simplify the implementation of pmap_enter_object() on
amd64, arm, and i386.
On all architectures where we support superpages, the cost of creating a
superpage mapping is roughly the same as creating a base page mapping. For
example, both kinds of mappings entail the creation of a single PTE and PV
entry. With this in mind, use the page size field to make the
implementation of vm_map_pmap_enter(..., MAP_PREFAULT_PARTIAL) a little
smarter. Previously, if MAP_PREFAULT_PARTIAL was specified to
vm_map_pmap_enter(), that function would only map base pages. Now, it will
create up to 96 base page or superpage mappings.
Reviewed by: kib
Sponsored by: EMC / Isilon Storage Division
SoC's registers base address may differ between boards
(0xf1000000 or 0xd0000000). Therefore, in order to use
the proper CPU Boot Address Redirect register during SMP
initialization in mptramp the real, physical address has
to be passed to mptramp based on the value from DT.
Reviewed by: gber
During Armada's platform_mp_start_ap(), mptramp code
is being copied to the specific physical location (0xffff0000).
Before r265694 the address to which the code should be copied
was equal to the address of mpentry routine that followed the
mptramp in locore.S. Now the mptramp end address should be
exported and used as a copy limit.
Reviewed by: gber
(7-bit device address << 1), always leaving the room for the read/write bit.
This commit convert ti_i2c and revert r259127 on bcm2835_bsc to make them
compatible with 8-bit addresses. Previous to this commit an i2c device
would have different addresses depending on the controller it was attached
to (by example, when compared to any iicbb(4) based i2c controller), which
was a pretty annoying behavior.
Also, update the PMIC i2c address on beaglebone* DTS files to match the new
address scheme.
Now the userland utilities need to do the correct slave address shifting
(but it is going to work with any i2c controller on the system).
Discussed with: ian
MFC after: 2 weeks
The ti_i2c controller only works in the master mode and the i2c address
passed on iicbus_reset() is used to set the controller slave address when
operating as an i2c slave (which isn't currently supported).
When talking to a slave, the slave address is correctly provided to
ti_i2c_tranfer().
through a voltage divisor (R163 and R164 on page 4 of BBB schematic).
Add a note about this on ti_adc(4) man page. The ti_adc(4) man page will
first appear on 10.1-RELEASE.
MFC after: 1 week
Suggested by: Sulev-Madis Silber (ketas)
Manual page reviewed by: brueffer (D127)
and the actual PWM frequency.
Enforce the maximum value for the period sysctl.
The frequency systcl now allows the direct setting of the PWM frequency (it
will try to find the better clkdiv and period for a given frequency, i.e.
the ones that will give the better PWM resolution).
This allows the use lower frequencies on the PWM. Without changing the
clock prescaler the minimum PWM frequency was 1.52kHz.
PWM frequencies checked with an osciloscope.
PWM output tested with some R/C servos at 50Hz.
o Allow setting keymap in FDT, use hardcoded one by default
o Represent fallback keymap as a list rather than directly usable M*N array
Submitted by: Maxim Ignatenko <gelraen.ua@gmail.com>
current RADXA config. Radxa Rock (RR) boards have few types such as
RR (full version), RR Lite and some variants of RR engineering samples.
Add kernel config and FDT file for RR Lite board.
Approved by: stas (mentor)
(XScale mainly) expects the memory located before the kernel to be mapped,
and use it to allocate the page tables, the various stacks, etc.
A better fix would probably be to rewrite the various bla_machdep.c to stop
using that RAM, but I'm not so inclined to do it, especially since I don't
have hardware for all of them.
Use armv7_setttb that sets proper PT attributes.
Get rid of unused CPU functions, put nullop instead.
Exchange obsolete pj4b_/arm11_ functions to the appropriate armv7_ ones.
memory ordering model allows writes to different devices to complete out
of order, leading to a situation where the write that clears an interrupt
source at a device can complete after a write that unmasks and EOIs the
interrupt at the interrupt controller, leading to a spurious re-interrupt.
This adds a generic barrier function specific to the needs of interrupt
controllers, and calls that function from the GIC and TI AINTC controllers.
There may still be other soc-specific controllers that need to make the call.
Reviewed by: cognet, Svatopluk Kraus <onwahe@gmail.com>
MFC after: 3 days
shared flag is set on normal-memory mappings made via pmap_kenter() for SMP.
The "shared flag" part of this change isn't obvious from the diff, here's
the deal... by using the array of preformatted page table entry templates
instead of constructing the PTE from scratch, we automatically get the
right attribute bits set for both caching and shared.
MFC after: 1 week
