15afc798fd
50 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Justin T. Gibbs
|
b3b25f2cbf |
ahc_eisa.c:
ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset. |
||
|
Justin T. Gibbs
|
1d528d6792 |
aic7770.c:
aic79xx.c: aic79xx.h: aic79xx_pci.c: aic7xxx.c: aic7xxx.h: aic7xxx_pci.c: Switch ah?_reset() to take an additional "reinit" argument. Use this instead of init_level to determin if the chip should be fully reinitialized after a chip reset. This is required so that ah?_shutdown() can reset the chip without side-effects. aic79xx.c: Implement ahd_suspend() and ahd_resume(). aic7xxx.c: Change ahc_loadseq() to *not* restart the sequencer. This brings the loadseq behavior in line with that of the 7902 driver and also simplifies the init routine. Correct the resume routine to enable interrupts and restart the sequencer. |
||
|
Justin T. Gibbs
|
d6b641de7f |
Constify a string used in our EISA probe tables.
Fix a few style nits. |
||
|
Justin T. Gibbs
|
92931c12ff |
Correct/Simplify ignore wide residue message handling
aic7xxx.c: In ahc_handle_ign_wide_residue(): o Use SCB_XFERLEN_ODD SCB field to determine transfer "oddness" rather than the DATA_COUNT_ODD logic. SCB_XFERLEN_ODD is toggled on every ignore wide residue message so that multiple ignore wide residue messages for the same transaction are properly supported. o If the sg list has been exausted, the sequencer doesn't bother to update the residual data count since it is known to be zero. Perform the zeroing manually before calculating the remaining data count. o Ensure that SG_LIST_NULL is cleared in the residual sg pointer for "mid-transfer" ignore wide residue cases. o Use multibyte in/out macros instead of shifting/masking by hand. aic7xxx.h: Modify the SCB_GET_LUN() macro to mask the lun hardware SCB field with LID. This leaves two bits in the LUN field that can be used for other purposes. aic7xxx.reg: Change LID to be 0x3F. This is the maximum supported lun size for non-packetized SCSI. Map the top bit of the lun to SCB_XFERLEN_ODD. The host must set this bit whenever a transfer is an odd length. Remove the ODD_SEG bit field that was used to carry the odd transfer length information through the SG cache. This is obviated by SCB_XFERLEN_ODD field. Remove the DATA_COUNT_ODD scratch ram byte that was used dynamicaly compute data transfer oddness. This is obviated by SCB_XFERLEN_ODD field. aic7xxx.seq: Be more careful in our handling of the SCB_LUN field. It must be masked with LID if only lun information is desired. Remove all updates to the DATA_COUNT_ODD scratch ram field. Remove all uses of ODD_SEG. These two save quite a few sequencer instructions. Use SCB_XFERLEN_ODD to validate the end of transfer ignore wide residue message case. aic7xxx_inline.h: In ahc_queue_scb(), setup the SCB_XFERLEN_ODD field. Approved by: RE |
||
|
Justin T. Gibbs
|
e4e6e6d6ea |
Fix disabling of PCI parity error interrupts. We need to set
FAILDIS in the SEQCTL register, not the HCNTRL register. aic7xxx.c: Remeber SEQCTL settings in the "seqctl" field of our softc. seqctl defaults to just having FASTMODE set, but the bus attachments can override this. aic7xxx.h: Add the seqctl softc field. aic7xxx_pci.c: Update the seqctl softc field and manually update SEQCTL when to many PCI errors occur Approved by: RE |
||
|
Justin T. Gibbs
|
9bf327a70c |
aic7xxx.c:
aic7xxx.h: Split out core chip initialization into ahc_chip_init(). This will allow us to reset the chip correctly at times other than initial chip setup. aic7770.c aic7xxx_pci.c: Flesh out bus chip init methods for our two bus attachments and use these, in addition to bus suspend/resume hooks to get the core in better shape for handling these events. When disabling PCI parity error checking, use FAILDIS. Although the chip docs indicate that clearing PERRESPEN should also work, it does not. Auto-disable pci parity error checking after informing the user of AHC_PCI_TARGET_PERR_THRESH number of parity errors observed as a target. aic7xxx.h: aic7xxx_pci.c aic7770.c aic7xxx.c Add the instruction_ram_size softc field. Remove the now unused stack_size softc field. Modify ahc_loadseq to return a failure code and to actually check the downloaded instruction count against the limit set in our softc. Modify callers of ahc_loadseq to handle load failures as appropriate. Set instruction RAM sizes for each chip type. aic7xxx_pci.c: Add some delay in the aic785X termination control code. This may fix problems with the 2930. Be consistent in how we access config space registers. 16bit registers are accessed using 16bit ops. aic7xxx.c: Correct spelling errors. Have ahc_force_renegotiation() take a devinfo as is done in the U320 driver. Use this argument to correct a bug in the selection timeout handler where we forced a renegotiation with the last device that had set SAVED_SCSIID. SAVED_SCSIID is only updated once a selection is *sucessfull* and so is stale for any selection timeout. Cleanup the setup of the devinfo for busfree events. We now use this devinfo for a call to ahc_force_renegotiation() at the bottom of the routine, so it must be initialized in all cases. In ahc_pause_and_flushwork(), adjust the loop so that it will exit in the hot-eject case even if the INT_PEND mask is something other than 0xFF (as it is in this driver). Correct a wrapping string constant. Call ahc_fini_scbdata() after shutdown so that any ahc_chip_init() routine that might access SCB data will not access free'd memory. Correctly setup our buffer tag to indicate that 39bit addressing is available if in 39bit addressing mode. Rearrange some variable declarations based on type size. aic7xxx.c aic7xxx.h: aic7xxx.reg: Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AHC_OFFSET_UNKNOWN. Change AHC_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. Change MAX_OFFSET to 0x7f which is the max offset U160 aic7xxx controllers can negotiate. This ensures that curr->offset will not match AHC_OFFSET_UNKNOWN. aic7xxx_inline.h: Have our inline interrupt handler return with a value indicating whether we serviced a real interrupt. This is required for Linux support. Return earlier if the interrupt is not for us. |
||
|
Justin T. Gibbs
|
70b41139c3 |
aic7xxx.reg:
Add a constant for the controller's stack size and the maximum scsi offset. aic7xxx.seq: Style nit. The source is implied to be the destination unless overridden in an "and" instruction. Update target mode code for changes in identify seen sequencer flags. aic7xxx_pci.c: Ensure that the PCIERRGENDIS bit is set in the PCIERRGEN config space register. Perhaps this is a reason for the spurios parity errors reported on U160 controllers. Honor the AHC_NO_BIOS_INIT flag. Allow PCI interrupt reporting to be disabled, by clearing the PERRRESEN bit in the command register. This option is now enabled via a new softc flag: AHC_DISABLE_PCI_PERR. Disable SERR and pause the controller prior to performing our mmapped I/O test. This should handle the case of controllers that do not "auto-access pause". For legacy controllers, use SCB ram instead of scratch ram since the latter may contain settings left over from the BIOS that we will use if an seeprom is not found. Make use of new ahc_inl/outl() inlines. aic7xxx.h: Reformat a few comments to follow driver style. Add a controller flags that indicate that a controller has not been initialized by the BIOS and whether to disable PCI parity errors.. Remove stack probing softc members. Add a few more syncrate constants that are useful in speed fallback calculations. Add the SHOW_MASKED_ERRORS debug flag. aic7xxx.h: aic7xxx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. aic7xxx_inline.h: Implement ahc_[in|out][w|l|q]. This removes the need for manual 'or and shift" type operations throughout the driver. aic7xxx.c: Move SELTO dignostic so that the SCB is still valid when we use it for printing path information. If we are narrow, limit syncrate to Ultra2. Don't clobber ppr_options when forcing a renegotiation. The current ppr_options may be referenced while queuing new commands. Don't set our width to unknown when forcing negotiation on narrow controllers. This will confuse the negotiation code into negotiating with a wide message on narrow controllers. Add an "asserting atn" diagnostic with controller/target information. Remove the probe_stack code. The stack is always 4 deep on legacy controllers, so probing is pointless. This also avoids an issue where probing the stack would upset the aic7770. In ahc_reset(), record whether or not we found the controller in a reset state. If the controller was already reset, assume that no BIOS has initialized the controller and ignore left over scratch ram settings. Fix an ifdef bug that caused sequencer debugging to be enabled always. Clear the ultraenb flag in our tstate during startup. The ultraenbled'ness of a device is recorded in the user transfer settings. tstate->ultraenb bitmask indicates which devices we have negotiated an ultra speed with. Just after initialization, we are async. Setting the ultraenb flag while async seems to be harmless, but it was confusing to see the ULTRAENB flag set in the SCB. Enhance residual diagnostic to indicate if the residual if for sense information or normal data transfers. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. In ahc_dump_card_state() fix a logic reversal. The SCSIPHASE register only exists on U160 controllers. The SCSISIGI register exists on all controllers. Not the other way around. Also print out the ERROR register. Allow ahc_dump_card_state() to be called when the sequencer is not paused. Add dump card state markers as in the U320 driver. |
||
Scott Long
|
4d22994e96 |
Bring in many bugfixes and changes obtained from formal testing:
aic7xxx.c:
aic7xxx.h:
aic7xxx.reg:
aic7xxx.seq:
Bring in the protocol violation handler from the U320
driver and replace the NO_IDENT sequencer interrupt code
with the PROTO_VIOLATION code. Support for this code
required the following changes:
SEQ_FLAGS:
IDENTIFY_SEEN -> NOT_IDENTIFIED
Added NO_CDB_SENT
SCB_CONTROL:
TARGET_SCB == STATUS_RCVD for initiator mode
scb->flags:
Added SCB_TARGET_SCB since we cannot rely on
TARGET_SCB as a target/initiator differentiator
due to it being overloaded in initiator mode to
indicate that status has been received.
aic7xxx.seq:
Move data fifo CLRCHN to mesgin_rdptrs which is a safer
location for doing this operation. This also saves a
sequencer instruction.
aic7xxx.c:
aic7xxx.h:
Change ahc/ahd_upate_neg_request() to take a "negotiation
type" enum that allows us to negotiate:
o only if the goal and current parameters differ.
o only if the goal is non-async
o always - even if the negotiation will be for async.
aic7xxx.seq:
Reset the FIFO whenever a short CDB transfer occurs
so that the FIFO contents do not corrupt a future CDB
transfer retry.
Add support for catching the various protocol violations
handled by ahc_handle_protocol_violation.
Reformat some comments.
aic7xxx.c:
aic7xxx.h:
Just for safety, have the aic7xxx driver probe
the stack depth.
aic7xxx.c:
aic7xxx.h:
Save and restore stack contents during diagnostics.
Some chip variants overwrite stale entries on a
stack "pop".
Don't use 0 to probe the stack depth. 0 is the typical
value used to backfill the stack if entries are overwritten
on a "pop".
aic7xxx.h:
Add a missing typedef.
Collapse SCB flag entries so they are bit contiguous.
Add AHD_ULTRA2_XFER_PERIOD for narrow fallback calculations
aic7xxx.c:
Don't panic (as a diagnostic to catch bugs) if we decided to
force the renegotiation of async even if we believe we are
already async. This should allow us to negotiate async instead
of the full user goal rate during startup if bus resets are
disabled.
Add a space to the end of the ahc/ahd_print_devinfo routines
so that it behaves as expected by the code that uses it.
Only force a renegotiation on a selection timeout
if the SCB was valid. Doing otherwise may be dangerous
as the connection was not valid for an unknown reason.
Add additional diagnostic output to ahc_dump_card_state(),
and have it use the register pretty printing functions.
Update ahc_reg_print() to handle a NULL cur_col.
Add a newline to ahc_dump_card_state() output.
Bring back "use_ppr". We need to use_ppr anytime
doppr is true or we have non-zero protocol options.
The later case was not handled in the recent removal
of use_ppr.
Move a comment and remove a useless clearing of use_ppr.
Don't disable ENBUSFREE when single stepping on
a DT capable controller. We cannot re-enable unexpected
busfree detection, so we must clear BUSFREE on each
step instead.
Correct the lookup of the SCB ID in ahc_handle_proto_error.
Remove a diagnostic printf.
Remove unecessary restoration of the STACK for older
chips.
Approved by: re (blanket)
|
||
|
Justin T. Gibbs
|
3b06611aa7 |
Drop the bus reset hold delay back down to 25us. The 250us
value slipped in from a debugging session. Add AHC_LSCBS_ENABLED and AHC_SCB_CONFIG_USED ahc_flags which allow for some code to move to the core. Remove extern for ahc_syncrates[]. The OSMs no longer need direct access to this array. Add serial eeprom field to the ahc softc. Prototype ahc_search_untagged_queues() and ahc_print_register(). Convert to AHC_SHOW_XXX debug option format. |
||
|
Justin T. Gibbs
|
8f214efc9a |
Major update to the aic7xxx driver:
ahc_eisa.c: ahc_pci.c: Conform to new aic7xxx IRQ API. Adapt to aic7xxx_freebsd -> aic7xxx_osm changes. aic7770.c: Disable card generated interrupt early in our probe for "extra safety" Commonize some seeprom code with the PCI side of the driver. aic7xxx.c: Correctly initialize a few scratch ram locations during a sequencer restart. This avoids spurious sequencer ram parity errors in some configurations. Include the softc in ahc_update_residual calls. We need it for some diagnostics in this code path. Flag a data overrun on an auto-request sense failure as a CAM_AUTOSENSE_FAIL rather than a CAM_DATA_RUN_ERR. Force a renegotiation after noticing a parity error. This covers targets that lose our negotiation settings but don't bother to give us a unit attention condition. This can happen if a target fails during a reselection of us during a cable pull. Convert some code to using constants. Fix some typos. Correct target mode message loop handling. ahc_clear_msg_state was not clearing the "need to go to message out phase" bit once our loop was over. Simplify some abort handling code. Include tag information in target mode immediate notify events. When shutting down EISA controllers, don't EISA BIOS settings in the high portions of scratch ram. This fixes warm boot issues on some systems. Save a bit of space by only allocating the SCBs that we can use. Avoid some code paths in ahc_abort_scbs() if we are currently acting as a target. Correctly cleanup stranded SCBs in the card's SCB array. These are SCBs who's mapping has already been torn down by code that aborted the SCB by seeing it in another list first. Add a comment about some potential bus reset issues for target mode on Twin (EISA only) controllers. aic7xxx.h: Cleanup the hardware scb definitions a bit. Allocate a ful 256 byte scb mapping index. This simplifies the lookup code since the table covers all possible (and potentially bogus) values. Make AHC_DEBUG work again. aic7xxx.reg: Updates to hardware SCB definition. New definitions for target mode fixes. aic7xxx.seq: In target mode, initialize SAVED_LUN just after we receive the identify message. It may be required in the error recovery path when a normal cdb packet (includes lun) is not sent up to the host for processing. Respond to irregular messages during a selection in target mode. Defer looking for space for a cdb packet until we are about to enter command phase. We want to be able to handle irregular messages even if we would otherwise return QUEUE_FULL or BUSY. Add support for sending Ignore Wide Residue messages as a target. In the disable disconnect case in target mode, set our transfer rate correctly once data are availble. aic7xxx_93cx6.c: aic7xxx_93cx6.h: Add the ability to write and erase the seeprom. aic7xxx_inline.h: Correct Big Endian handling of large cdb sizes (> 12 bytes). Adaptec to changes in the calc_residual API. Correct a target mode bug where we always attempted to service the input queue even if no progress could be made due to lack of ATIOs. aic7xxx_osm.c: Adaptec to new IRQ mapping API. The new API allows the core to only enable our IRQ mapping once it is safe (sufficient initialization) to do so. Slap bootverbose protection around some diagnostics. Only attempt DT phases if we are wide. aic7xxx_osm.h: Enable big endian support. Adjust for IRQ API change. aic7xxx_pci.c: Be more careful about relying on subvendor 9005 information. We now only trust it for HBAs. This should allow the driver to attach to some MBs where the subvendor/device information does not follow the Adaptec spec. Only enable interrupts on the card once we are fully setup. Disable external SCB ram usage on the aic7895. I have not been able to make it 100% reliable. Adjust to seeprom routines being properly prefixed with "ahc". Fix a few bugs in the external SCB ram probing routine. We need to clear any parity errors we've triggered during the probe to avoid future, fatal, interrupts. If we detect an invalid cable combination, pretent there are no cable at all. This will enable all of the terminators which is probably the safest configuration we can "guess". MFC after: 4 days |
||
|
Justin T. Gibbs
|
cd036e891a |
ahc_pci.c:
If bus_dma will give us addresses > 32 bits, setup our dma tag to accept up to 39bit addresses. aic7770.c: Update the softc directly rather than use an intermediate "probe_config" structure. aic7xxx.c: Complete core work to support 39bit addresses for bulk data dma operations. Controller data structures still must reside under the 4GB boundary to reduce code/data size in the sequencer and related data structures. This has been tested under Linux IA64 and will be tested on IA64 for FreeBSD as soon as our port can run there. Add bus dmamap synchronization calls around manipulation of all controller/kernel shared host data structures. Implement data pointer reinitialation for a second data phase in a single connection in the kernel rather than bloat the sequencer. This is an extremely rare operation (does it ever happen?) and the sequencer implementation was flawed for some of the newest chips. Don't ever allow our target role to initiate a PPR. This is forbidden by the SCSI spec. Add a few missing endian conversions in the ignore wide pointers code. The core has been tested on the PPC under Linux and should work for FreeBSD PPC. As soon as I can test the OSM layer for FreeBSD PPC, I will. Move some of ahc_softc_init() into ahc_alloc() now that the probe_config structure is gone. Add a 4GB boundary condition on all of our dma tags. 32bit DAC under PCI only works on a single 4GB "page". Although we can cross 4GB on a true 64bit bus, the card won't always be installed in one and we can save code space and cost in implementing high address support by assuming the high DWORD address will never change. Add diagnostics to ahc_search_qinfifo(). Correct a target mode issue with bus resets. To avoid an interrupt storm from a malicious third party holding the reset line, the sequencer would defer re-enabling the reset interrupt until either a select-out or select-in. Unfortunately, the select-in enable bit is cleared by a bus reset, so a second reset will render the card deaf to an initiator's attempts to contact it. We now re-enable bus reset interrupts immediately if the target role is enabled. aic7xxx.h: Remove struct ahc_probe_config. SCB's now contain a pointer to the sg_map_node so we can perfrom bus dma sync operations on the SG list prior to queuing a command. aic7xxx.reg: Register the Perforce ID for this file with the VERSION keyword so it is printed in generated files. Add the DSCOMMAND1 register which is used to access the high DWORD of address bits. Add the data pointer reinitialize sequencer interrupt code. aic7xxx.seq: Register the Perforce ID for this file with the VERSION keyword so it is printed in generated files. Remove code to re-enable the bus reset interrupt after a select-in. In target mode we cannot defer this operation as ENSELI is cleared by a bus reset. Complete 39bit support. Generate a sequencer inteerrupt rather than handle the data pointers re-initialitation in the sequencer. Inline the "seen identify" assertion to save a few cycles. Short circuit the update of our residual data if we have fully completed a transfer. The residual is correct from our last S/G load operation. Short circuit full SDPTR processing if the residual is 0. Just mark the transfer as complete. aic7xxx_93cx6.c: Synchronize perforce IDs. aic7xxx_freebsd.c: Complete untested 39bit support. Add missing endia conversions. Clear our residuals prior to starting a command. The update residual code in the core only sets the residual if there is one. aic7xxx_freebsd.h: Modeify ahc_dmamap_sync() macros to take an offset and a length. This is how sync operations are performed in NetBSD, and we should update our bus dma implementation to match. aic7xxx_inline.h: Add data structure synchronization helper functions. Fix a bug in ahc_intr() where we would not clear our unsolicited interrupt counter after running our PCI interrupt handler. This may have been the cause of the spurious PCI interrupt messages. aic7xxx_pci.c: Adjust for loss of probe_config structure. Guard against bogus 9005 subdevice information as seen on some IBM MB configurations. Add 39bit address support. MFC after: 10 days |
||
|
Justin T. Gibbs
|
58fb7d8e0b |
ahc_eisa.c:
ahc_pci.c:
Prepare for making ahc a module by adding module dependency
and version info.
aic7770.c:
Remove linux header ifdefs. The headers are handled differently
in Linux where local includes (those using "'s instead of <>'s)
are allowed.
Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.
aic7xxx.c:
Remove linux header ifdefs.
current->curr to avoid Linux's use of current as a
#define for the current task on some architectures.
Add a helper function, ahc_assert_atn(), for use in
message phases we handle manually. This hides the fact
that U160 chips with the expected phase matching disabled
need to have SCSISIGO updated differently.
if (ahc_check_residual(scb) != 0)
ahc_calc_residual(scb);
else
ahc_set_residual(scb, 0);
becomes:
ahc_update_residual(scb);
Modify scsi parity error (or CRC error) handling to
reflect expected phase being disabled on U160 chips.
Move SELTO handling above BUSFREE handling so we can
use the new busfree interrupt behavior on U160 chips.
In ahc_build_transfer_msg() filter the period and ppr_options
prior to deciding whether a PPR message is required.
ppr_options may be forced to zero which will effect our
decision.
Correct a long standing but latent bug in ahc_find_syncrate().
We could choose a DT only rate even though DT transfers were
disabled. In the CAM environment this was unlikely as CAM
filters our rate to a non-DT value if the device does not
support such rates.
When displaing controller characteristics, include the
speed of the chip. This way we can modify the transfer
speed based on optional features that are enabled/disabled
in a particular application.
Add support for switching from fully blown tagged queing
to just using simple queue tags should the device reject
an ordered tag.
Remove per-target "current" disconnect and tag queuing
enable flags. These should be per-device and are not
referenced internally be the driver, so we let the OSM
track this state if it needs to.
Use SCSI-3 message terminology.
aic7xxx.h:
The real 7850 does not support Ultra modes, but there are
several cards that use the generic 7850 PCI ID even though
they are using an Ultra capable chip (7859/7860). We start
out with the AHC_ULTRA feature set and then check the
DEVSTATUS register to determine if the capability is really
present.
current -> curr
ahc_calc_residual() is no longer static allowing it to
be called from ahc_update_residual() in aic7xxx_inline.h.
Update some serial eeprom definitions for the latest
BIOS versions.
aic7xxx.reg:
Add a combined DATA_PHASE mask to the SCSIPHASE register
definition to simplify some sequencer code.
aic7xxx.seq:
Take advantage of some performance features available only
on the U160 chips. The auto-ack feature allows us to ack
data-in phases up to the data-fifo size while the sequencer
is still setting up the DMA engine. This greatly reduces
read transfer latency and simplifies testing for transfer
complete (check SCSIEN only). We also disable the expected
phase feature, and enable the new bus free interrupt behavior,
to avoid a few instructions.
Re-arrange the Ultra2+ data phase handling to allow us to
do more work in parallel with the data fifo flushing on a
read.
On an SDTR, ack the message immediately so the target can
prepare the next phase or message byte in parallel with
our work to honor the message.
aic7xxx_93cx6.c:
Remove linux header ifdefs.
aic7xxx_freebsd.c:
current -> curr
Add a module event handler.
Handle tag downgrades in our ahc_send_async() handler.
We won't be able to downgrade to "basic queuing" until
CAM is made aware of this queuing type.
aic7xxx_freebsd.h:
Include cleanups.
Define offsetof if required.
Correct a few comments.
Update prototype of ahc_send_async().
aic7xxx_inline.h:
Implement ahc_update_residual().
aic7xxx_pci.c:
Remove linux header ifdefs.
Correct a few product strings.
Enable several U160 performance enhancing features.
Modify Ultra capability determination so we will enable
Ultra speeds on devices with a 7850 PCI id that happen
to really be a 7859 or 7860.
Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.
|
||
|
Justin T. Gibbs
|
b95de6dafd |
aic7770.c:
aic7xxx_pci.c: Enable board generation of interrupts only once our handler is in place and all other setup has occurred. aic7xxx.c: More conversion of data types to ahc_* names. tmode_tstate and tmode_lstate are the latest victims. Clean up the check condition path by branching early rather than indenting a giant block of code. Add support for target mode initiated sync negotiation. The code has been tested by forcing the feature on for all devices, but for the moment is left inaccesible until a decent mechanism for controlling the behavior is complete. Implementing this feature required the removal of the old "target message request" mechanism. The old method required setting one of the 16 bit fields to initiate negotiation with a particular target. This had the nice effect of being easy to change the request and have it effect the next command. We now set the MK_MESSAGE bit on any new command when negotiation is required. When the negotiation is successful, we walk through and clean up the bit on any pending commands. Since we have to walk the commands to reset the SCSI syncrate values so no additional work is required. The only drawback of this approach is that the negotiation is deferred until the next command is queued to the controller. On the plus side, we regain two bytes of sequencer scratch ram and 6 sequencer instructions. When cleaning up a target mode instance, never remove the "master" target mode state object. The master contains all of the saved SEEPROM settings that control things like transfer negotiations. This data will be cloned as the defaults if a target mode instance is re-instantiated. Correct a bug in ahc_set_width(). We neglected to update the pending scbs to reflect the new parameters. Since wide negotiation is almost always followed by sync negotiation it is doubtful that this had any real effect. When in the target role, don't complain about "Target Initiated" negotiation requests when an initiator negotiates with us. Defer enabling board interrupts until after ahc_intr_enable() is called. Pull all info that used to be in ahc_timeout for the FreeBSD OSM into ahc_dump_card_state(). This info should be printed out on all platforms. aic7xxx.h: Add the SCB_AUTO_NEGOITATE scb flag. This allows us to discern the reason the MK_MESSAGE flag is set in the hscb control byte. We only want to clear MK_MESSAGE in ahc_update_pending_scbs() if the MK_MESSAGE was set due to an auto transfer negotiation. Add the auto_negotiate bitfield for each tstate so that behavior can be controlled for each of our enabled SCSI IDs. Use a bus interrupt handler vector in our softc rather than hard coding the PCI interrupt handler. This makes it easier to build the different bus attachments to the aic7xxx driver as modules. aic7xxx.reg: Remove the TARGET_MSG_REQUEST definition for sequencer ram. aic7xxx.seq: Fix a few target mode bugs: o If MK_MESSAGE is set in an SCB, transition to message in phase and notify the kernel so that message delivery can occur. This is currently only used for target mode initiated transfer negotiation. o Allow a continue target I/O to compile without executing a status phase or disconnecting. If we have not been granted the disconnect privledge but this transfer is larger than MAXPHYS, it may take several CTIOs to get the job done. Remove the tests of the TARGET_MSG_REQUEST field in scratch ram. aic7xxx_freebsd.c: Add support for CTIOs that don't disconnect. We now defer the clearing of our pending target state until we see a CTIO for that device that has completed sucessfully. Be sure to return early if we are in a target only role and see an initiator only CCB type in our action routine. If a CTIO has the CAM_DIS_DISCONNECT flag set, propogate this flag to the SCB. This flag has no effect if we've been asked to deliver status as well. We will complete the command and release the bus in that case. Handle the new auto_negotiate field in the tstate correctly. Make sure that SCBs for "immediate" (i.e. to continue a non disconnected transaction) CTIO requests get a proper mapping in the SCB lookup table. Without this, we'll complain when the transaction completes. Update ahc_timeout() to reflect the changes to ahc_dump_card_state(). aic7xxx_inline.h: Use ahc->bus_intr rather than ahc_pci_intr. |
||
|
Justin T. Gibbs
|
6fb77fef4d |
This is an MFC candidate.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
|
||
Jeroen Ruigrok van der Werven
|
7c63796828 | Preceed/preceeding are not english words. Use precede or preceding. | ||
|
Justin T. Gibbs
|
bfadd24d57 |
aic7xxx.c:
Style nits. Make sure that our selection hardware is disabled as soon as possible after detecting a busfree and even go so far as to disable the selection hardware in advance of an event that will cause a busfree (ABORT or BUS DEVICE RESET message). The concern is that the selection hardware will select a target for which, after processing the bus free, there will be no commands pending. The sequencer idle loop will re-enable the selection should it still be necessary. In ahc_handle_scsiint(), clear SSTAT0 events several PCI transactions (most notably reads) prior to clearing SCSIINT. The newer chips seem to take a bit of time to see the change which can make the clearing of SCSIINT ineffective. Don't bother panicing at the end of ahc_handle_scsiint(). Getting to the final else just means we lost the race with clearing SCSIINT. In ahc_free(), handle init-level 0. This can happen when we fail the attach for RAID devices. While I'm here, also kill the parent dma tag. In ahc_match_scb(), consider initiator ccbs to be any that are not from the target mode group. This fixes a bug where an external target reset CCB was not getting cleaned up by the reset code. Don't bother freezing a ccb in any of our "abort" routines when the status is set to CAM_REQ_CMP. This can happen for a target reset ccb. aic7xxx.reg: Reserve space for a completion queue. This will be used to enhance performance in the near future. aic7xxx.seq: Remove an optimization for the 7890 autoflush bug that turned out to allow, in rare cases, some data to get lost. Implement a simpler, faster, fix for the PCI_2_1 retry bug that hangs the sequencer on an SCB dma for certain chips. Test against SAVED_SCSIID rather than SELID during target reselections. This is how we always did it in the past, but the code was modified while trying to work around an issue with the 7895. SAVED_SCSIID takes into account twin channel adapters such as the 2742T, whereas SELID does not have the channel bit. This caused invalid selection warnings and other strangeness on these cards. aic7xxx_pci.c Use the correct mask for checking the generic aic7892 entry. |
||
|
Justin T. Gibbs
|
64a3876fef | Update Copyright notices for new year. (should have been in last commit). | ||
|
Justin T. Gibbs
|
a5847d5c27 |
ahc_eisa.c:
Initialize rid to 0. This doesn't seem to make any difference (the driver doesn't care what rid it gets and no-one seems to check rid's value), but follows standard conventions. Pass in our device_t to ahc_alloc(). We now use device_T softc storage, so passing NULL results in a panic. Set the unit number in our softc so that the driver core can retrieve it. ahc_pci.c: Set the unit number in our softc so that the driver core can retrieve it. aic7770.c: Insert our softc into the list of softcs when initialization is successful. aic7xxx.c: Remove a workaround for an aic7895 bug we will never trigger. Add additional diagnostic info to ahc_dump_card_state(). Always panic the system if a sequencer assertion fails. AHC_SCB_BTT is a "flag" not a "feature". Check the right field in the softc. Replace a hard coded number with a constant. Guard against looping forever in ahc_pause_and_flushwork(). A hot eject or card failure may make the intstat register return 0xFF, so limit the number of interrupts we'll process. Correct the code in ahc_search_qinfifo() that guarantees that the sequencer will see an abort collision if the qinfifo is modified when a DMA is in progress. We now do this fixup after modifying the queue. This guarantees that the HSCB we place at the head of the queue is not the same as the old head. Using "next hscb" (guaranteed not to be the same as the first SCB) before clearing the queue could free up the original head hscb to be used during a remove operation placing it again at the head of the qinfifo. aic7xxx.h: Reduce the maximum number of outstanding commands to 253 from 254. To handle our output queue correctly on machines that only support 32bit stores, we must clear the array 4 bytes at a time. To avoid colliding with a DMA write from the sequencer, we must be sure that 4 slots are empty when we write to clear the queue. This reduces us to 253 SCBs: 1 that just completed and the known three additional empty slots in the queue that preceed it. Yahoo was able to force this race on one of their systems. Interrupts were disabled for such a time that the entire output queue was filled (254 entries complete without any processing), and our 32bit write to clear the status clobbered one entry. Add a feature tag for devices that are removable. aic7xxx.reg: Never use the sequencer interrupt value of 0xF0. We need to guanrantee that an INTSTAT value of 0xFF can only occur during card failure or a hot-eject. Align the busy targets table with the begining of scratch space. This seems to appease a chip bug in the aic7895. aic7xxx.seq: Be sure to disable select-out after a bus free event that occurs early in a selection. If we don't disable select-out, we will believe that it is enabled even though a new selection will never occur. Move the clearing of SELDI to just before a jump. This appeases another chip bug of the aic7895. Make the target mode command loop a bit more efficient. AHC_SCB_BTT is a "flag" not a "feature". Check the right field in the softc. Properly cleanup the last SCB we tested against should we fail to properly find an SCB for a reselection. Add some additional sequencer debugging code. aic7xxx_freebsd.c: Limit the driver to 253 outstanding commands per adapter. Guard against overflow in timeout handling. aic7xxx_inline.h: AHC_SCB_BTT is a "flag" not a "feature". Check the right field in the softc. aic7xxx_pci.c: Set the removable feature for the apa1480 cardbus and the 29160C Compact PCI card. Don't report high byte termination information for narrow cards. Use a PCI read rather than a questionable delay when fetching/setting termination settings. |
||
|
Justin T. Gibbs
|
f8838555e8 |
aic7xxx.c:
aic7xxx.h: First pass at big-endian support in the Core. Capture state for second channel on TWIN channel adapters for suspend and resume. aic7xxx_freebsd.h: Stubs for endian conversion functions. These will get filled out once we get an official kernel api for this kind of thing that is something more elegant and efficient than a bunch of manual swaps #ifdefed by platform. aic7xxx_pci.c Allow the second channel of motherboard aic7896 chips to be attached. It turns out that the encoding of the subdevice id differs between PCI cards and MB based controllers and our check to see, via the subvendor id, if the second channel was "stuffed" always turned out negative. |
||
|
Justin T. Gibbs
|
56a7c4a852 |
ahc_eisa.c:
ahc_pci.c: Add detach support. Make use of soft allocated on our behalf by newbus. For PCI devices, disable the mapping type we aren't using for extra protection from rogue code. aic7xxx_93cx6.c: aic7xxx_93cx6.h: Sync perforce IDs. aic7xxx_freebsd.c: Capture the eventhandle returned by EVENTHANDER_REGISTER so we can kill the handler off during detach. Use AHC_* constants instead of hard coded numbers in a few more places. Test PPR option state when deciding to "really" negotiate when the CAM_NEGOTIATE flag is passed in a CCB. Make use of core "ahc_pause_and_flushwork" routine in our timeout handler rather than re-inventing this code. Cleanup all of our resources (really!) in ahc_platform_free(). We should be all set to become a module now. Implement the core ahc_detach() routine shared by all of the FreeBSD front-ends. aic7xxx_freebsd.h: Softc storage for our event handler. Null implementation for the ahc_platform_flushwork() OSM callback. FreeBSD doesn't need this as XPT callbacks are safe from all contexts and are done directly in ahc_done(). aic7xxx_inline.h: Implement new lazy interrupt scheme. To avoid an extra PCI bus read, we first check our completion queues to see if any work has completed. If work is available, we assume that this is the source of the interrupt and skip reading INTSTAT. Any remaining interrupt status will be cleared by a second call to the interrupt handler should the interrupt line still be asserted. This drops the interrupt handler down to a single PCI bus read in the common case of I/O completion. This is the same overhead as in the not so distant past, but the extra sanity of perforning a PCI read after clearing the command complete interrupt and before running the completion queue to avoid missing command complete interrupts added a cycle. aic7xxx.c: During initialization, be sure to initialize all scratch ram locations before they are read to avoid parity errors. In this case, we use a new function, ahc_unbusy_tcl() to initialize the scratch ram busy target table. Replace instances of ahc_index_busy_tcl() used to unbusy a tcl without looking at the old value with ahc_unbusy_tcl(). Modify ahc_sent_msg so that it can find single byte messages. ahc_sent_msg is now used to determine if a transfer negotiation attempt resulted in a bus free. Be more careful in filtering out only the SCSI interrupts of interest in ahc_handle_scsiint. Rearrange interrupt clearing code to ensure that at least one PCI transaction occurrs after hitting CLRSINT1 and writting to CLRINT. CLRSINT1 writes take a bit to take effect, and the re-arrangement provides sufficient delay to ensure the write to CLRINT is effective. The old code might report a spurious interrupt on some "fast" chipsets. export ahc-update_target_msg_request for use by OSM code. If a target does not respond to our ATN request, clear it once we move to a non-message phase. This avoids sending a MSG_NOOP in some later message out phase. Use max lun and max target constants instead of hard-coded values. Use softc storage built into our device_t under FreeBSD. Fix a bug in ahc_free() that caused us to delete resources that were not allocated. Clean up any tstate/lstate info in ahc_free(). Clear the powerdown state in ahc_reset() so that registers can be accessed. Add a preliminary function for pausing the chip and processing any posted work. Add a preliminary suspend and resume functions. aic7xxx.h: Limit the number of supported luns to 64. We don't support information unit transfers, so this is the maximum that makes sense for these chips. Add a new flag AHC_ALL_INTERRUPTS that forces the processing of all interrupt state in a single invokation of ahc_intr(). When the flag is not set, we use the lazy interrupt handling scheme. Add data structures to store controller state while we are suspended. Use constants instead of hard coded values where appropriate. Correct some harmless "unsigned/signed" conflicts. aic7xxx.seq: Only perform the SCSIBUSL fix on ULTRA2 or newer controllers. Older controllers seem to be confused by this. In target mode, ignore PHASEMIS during data phases. This bit seems to be flakey on U160 controllers acting in target mode. aic7xxx_pci.c: Add support for the 29160C CPCI adapter. Add definitions for subvendor ID information available for devices with the "9005" vendor id. We currently use this information to determine if a multi-function device doesn't have the second channel hooked up on a board. Add rudimentary power mode code so we can put the controller into the D0 state. In the future this will be an OSM callback so that in FreeBSD we don't duplicate functionality provided by the PCI code. The powerstate code was added after I'd completed my regression tests on this code. Only capture "left over BIOS state" if the POWRDN setting is not set in HCNTRL. In target mode, don't bother sending incremental CRC data. |
||
|
Justin T. Gibbs
|
72df3c5621 |
Sync Perforce IDs, add tranceiver state change support, and correct
numerous error recovery buglets. Many thanks to Tor Egge for his assistance in diagnosing problems with the error recovery code. aic7xxx.c: Report missed bus free events using their own sequencer interrupt code to avoid confusion with other "bad phase" interrupts. Remove a delay used in debugging. This delay could only be hit in certain, very extreme, error recovery scenarios. Handle transceiver state changes correctly. You can now plug an SE device into a hot-plug LVD bus without hanging the controller. When stepping through a critical section, panic if we step more than a reasonable number of times. After a bus reset, disable bus reset interupts until we either our first attempt to (re)select another device, or another device attemps to select us. This removes the need to busy wait in kernel for the scsi reset line to fall yet still ensures we see any reset events that impact the state of either our initiator or target roles. Before this change, we had the potential of servicing a "storm" of reset interrupts if the reset line was held for a significant amount of time. Indicate the current sequencer address whenever we dump the card's state. aic7xxx.reg: Transceiver state change register definitions. Add the missed bussfree sequencer interrupt code. Re-enable the scsi reset interrupt if it has been disabled before every attempt to (re)select a device and when we have been selected as a target. When being (re)selected, check to see if the selection dissappeared just after we enabled our bus free interrupt. If the bus has gone free again, go back to the idle loop and wait for another selection. Note two locations where we should change our behavior if ATN is still raised. If ATN is raised during the presentation of a command complete or disconnect message, we should ignore the message and expect the target to put us in msgout phase. We don't currently do this as it requires some code re-arrangement so that critical sections can be properly placed around our handling of these two events. Otherwise, we cannot guarantee that the check of ATN is atomic relative to our acking of the message in byte (the kernel could assert ATN). Only set the IDENTIFY_SEEN flag after we have settled on the SCB for this transaction. The kernel looks at this flag before assuming that SCB_TAG is valid. This avoids confusion during certain types of error recovery. Add a critical section around findSCB. We cannot allow the kernel to remove an entry from the disconnected list while we are traversing it. Ditto for get_free_or_disc_scb. aic7xxx_freebsd.c: Only assume that SCB_TAG is accurate if IDENTIFY_SEEN is set in SEQ_FLAGS. Fix a typo that caused us to execute some code for the non-SCB paging case when paging SCBs. This only occurred during error recovery. |
||
|
Justin T. Gibbs
|
dd1290f033 |
aic7xxx.c:
Filter incoming transfer negotiation requests to ensure they never exceed the settings specified by the user. In restart sequencer attempt to deal with a bug in the aic7895. If a third party reset occurs at just the right time, the stack register can lock up. When restarting the sequencer after handling the SCSI reset, poke SEQADDR1 before resting the sequencers program counter. When something strange happens, dump the card's transaction state via ahc_dump_card_state(). This should aid in debugging. Handle request sense transactions via the QINFIFO instead of attaching them to the waiting queue directly. The waiting queue consumes card SCB resources and, in the pathological case of every target on the bus beating our selection attemps and issuing a check condition, could have caused us to run out of SCBs. I have never seen this happen, and only early cards with 3 or 4 SCBs had any real chance of ever getting into this state. Add additional sequencer interrupt codes to support firmware diagnostics. The diagnostic code is enabled with the AHC_DEBUG_SEQUENCER kernel option. Make it possible to switch into and out of target mode on the fly. The card comes up by default as an initiator but will switch into target mode as soon as an enable lun operation is performed. As always, target mode behavior is gated by the AHC_TMODE_ENABLE kernel option so most users will not be affected by this change. In ahc_update_target_msg_request(), also issue a new request if the ppr_options have changed. Never issue a PPR as a target. It is forbidden by the spec. Correct a bug in ahc_parse_msg() that prevented us from responding to PPR messages as a target. Mark SCBs that are on the untagged queue with a flag instead of checking several fields in the SCB to see if the SCB should be on the queue. This makes it easier for things like automatic request sense requests to be queued without touching the untagged queues even though they are untagged requests. When dealing with ignore wide residue messages that occur in the middle of a transfer, reset HADDR, not SHADDR for non-ultra2 chips. Although SHADDR is where the firmware fetches the ending transfer address for a save data pointers request, it is readonly. Setting HADDR has the side effect of also updating SHADDR. Cleanup the output of ahc_dump_card_state() by nulling out the free scb list in the non-paging case. The free list is only used if we must page SCBs. Correct the transmission of cdbs > 12 bytes in length. When swapping HSCBs prior to notifing the sequencer of the new transaction, the bus address pointer for the cdb must also be recalculated to reflect its new location. We now defer the calculation of the cdb address until just before queing it to the card. When pulling transfer negotiation settings out of scratch ram, convert 5MHz/clock doubled settings to 10MHz. Add a new function ahc_qinfifo_requeue_tail() for use by error recovery actions and auto-request sense operations. These operations always occur when the sequencer is paused, so we can avoid the extra expense incurred in the normal SCB queue method. Use the BMOV instruction for all single byte moves on controllers that support it. The bmov instruction is twice as fast as an AND with an immediate of 0xFF as is used on older controllers. Correct a few bugs in ahc_dump_card_state(). If we have hardware assisted queue registers, use them to get the sequencer's idea of the head of the queue. When enumerating the untagged queue, it helps to use the correct index for the queue. aic7xxx.h: Indicate via a feature flag, which controllers can take on both the target and the initiator role at the same time. Add the AHC_SEQUENCER_DEBUG flag. Add the SCB_CDB32_PTR flag used for dealing with cdbs with lengths between 13 and 32 bytes. Add new prototypes. aic7xxx.reg: Allow the SCSIBUSL register to be written to. This is required to fix a selection timeout problem on the 7892/99. Cleanup the sequencer interrupt codes so that all debugging codes are grouped at the end of the list. Correct the definition of the ULTRA_ENB and DISC_DSB locations in scratch ram. This prevented the driver from properly honoring these settings when no serial eeprom was available. Remove an unused sequencer flag. aic7xxx.seq: Just before a potential select-out, clear the SCSIBUSL register. Occasionally, during a selection timeout, the contents of the register may be presented on the bus, causing much confusion. Add sequencer diagnostic code to detect software and or hardware bugs. The code attempts to verify most list operations so any corruption is caught before it occurs. We also track information about why a particular reconnection request was rejected. Don't clobber the digital REQ/ACK filter setting in SXFRCTL0 when clearing the channel. Fix a target mode bug that would cause us to return busy status instead of queue full in respnse to a tagged transaction. Cleanup the overrun case. It turns out that by simply butting the chip in bitbucket mode, it will ack any bytes until the phase changes. This drasticaly simplifies things. Prior to leaving the data phase, make sure that the S/G preload queue is empty. Remove code to place a request sense request on the waiting queue. This is all handled by the kernel now. Change the semantics of "findSCB". In the past, findSCB ensured that a freshly paged in SCB appeared on the disconnected list. The problem with this is that there is no guarantee that the paged in SCB is for a disconnected transation. We now defer any list manipulation to the caller who usually discards the SCB via the free list. Inline some busy target table operations. Add a critical section to protect adding an SCB to the disconnected list. aic7xxx_freebsd.c: Handle changes in the transfer negotiation setting API to filter incoming requests. No filtering is necessary for "goal" requests from the XPT. Set the SCB_CDB32_PTR flag when queing a transaction with a large cdb. In ahc_timeout, only take action if the active SCB is the timedout SCB. This deals with the case of two transactions to the same device with different timeout values. Use ahc_qinfifo_requeu_tail() instead of home grown version. aic7xxx_inline.h: Honor SCB_CDB32_PTR when queuing a new request. aic7xxx_pci.c: Use the maximum data fifo threshold for all chips. |
||
|
Justin T. Gibbs
|
70351c9a14 |
Store a pointer to our softc in the kernel's SCB structure. In the
past we stored this data in the CCB and attained the CCB via a pointer in the SCB. In ahc_timeout(), however, the timedout SCB may have already been completed (inherent race), meaning that the CCB could have been recycled, and the ahc pointer reset. Clean up the logic in ahc_search_qinfifo that deals with the busy device table. For some reason it assumed that the only valid time to search to see if additional lun entries should be checked was if lun 0 matched. Now we properly itterate through the necessary luns. The busy device table is used to detect invalid reselections, so a device would have had to perform an unexpected reselection for this to cause problems. Further, all luns are collapsed to a single entry unless we have external ram with large SCBs (3940AU models) so the chance of this happening was rather remote. Clean up the logic for dealing with the untagged queues. We now set a flag in the SCB that indicates that it is on the untagged queue instead of inferring this from the type and setup of the CCB pased into us by CAM. In ahc_timeout(), don't print the path of the SCB until the controller is paused and we are sure that it has not completed yet. This, in conjunction with referencing the ahc pointer in the SCB rather than the CCB in the SCB avoids panics in the case of a timedout scb completing just before the timeout handler runs. This turns out to be guaranteed if interrupt delivery is failing, as we run our interrupt handler to flush any "just missed events" when a timeout occurs. Mention the likelyhood of broken interrupts if a timedout SCB is completed by our call to ahc_intr(). |
||
|
Justin T. Gibbs
|
73f1c25915 |
Clean up error recovery code:
aic7xxx.c: In target mode, reset the TQINPOS on every restart of the sequencer. In the past we did this only during a bus reset, but there are other reasons the sequencer might be reset. In ahc_clear_critical_section(), disable pausing chip interrupts while we step the sequencer out of a critical section. This avoids the possibility of getting a pausing interrupt (unexpected bus free, bus reset, etc.) that would prevent the sequencer from stepping. Send the correct async notifications in the case of a BDR or bus reset. In ahc_loadseq(), correct the calculation of our critical sections. In some cases, the sections would be larger than needed. aic7xxx.h: Remove an unused SCB flag. aic7xxx.seq: MK_MESSAGE is cleared by the kernel, there is no need to waste a sequencer instruction clearing it. aic7xxx_freebsd.c: Go through the host message loop instead of issuing a single byte message directly in the ahc_timeout() case where we are currently on the bus to the device. The effect is the same, but this way we get a nice printf saying that an expected BDR was delivered instead of an unexpected bus free. If we are requeuing an SCB for an error recovery action, be sure to set the DISCONNECTED flag in the in-core version of the SCB. This ensures that, in the SCB-paging case, the sequencer will still recognize the reselection as valid even if the version of the SCB with this flag set was never previously paged out to system memory. In the non-paging case, set the MK_MESSAGE flag in SCB_CONTROL directly. aic7xxx_pci.c: Enable the Memeory Write and Invalidate bug workaround for all aic7880 chips with revs < 1. This bug is rarely triggered in FreeBSD as most transfers end on cache-aligned boundaries, but a recheck of my references indicates that these chips are affected. |
||
|
Justin T. Gibbs
|
039c6f3637 |
Correct corruption of the qinfifo in ahc_search_qinififo() for all
non-LVD controllers. We only need to take special action on the qinfifo if we have dectected the case of an SCB that has been removed from the qinfifo but has not been fully DMAed to the controller. A missing conditional caused this code to be executed every time an SCB was aborted from the queue Don't attempt to print the path of an SCB that has been freed. Clean up the traversal of the pending scb list in ahc_update_pending_syncrates(). This has no functional change. Correct ahc_timeout()'s requeing of a timedout SCB to effect a recovery action. We now use ahc_qinfifo_requeue() and a new function ahc_qinfifo_count() instead of performing the requeue inline. The old code did not conform to the new qinfifo method. Clear the timedout SCB from the disconnected list. This ensures that the SCB_NEXT field is free to be used for queuing us to the qinfifo. |
||
|
Justin T. Gibbs
|
a49630ac82 |
Convert the driver to use a single DMA for fetching new commands instead
of two (one to access the circular input fifo, the other to get the SCB). This costs us a command slot so the driver can now only queue 254 simultaneous commands. Have the kernel driver honor critical sections in sequencer code. When prefetching S/G segments only pull a cacheline's worth but never less than two elements. This reduces the impact of the prefetch on the main data transfer when compared to the 128 byte fetches the driver used to do. Add "bootverbose" logging for transfer negotiations. Correct a bug in ahc_set_syncrate() that would prevent an update of the sync parameters if only the ppr_options had changed. Correct locking for calls to ahc_free_scb(). ahc_free_scb() is no longer protected internally to simplify ports to other platforms. Make sure we unfreeze our SIMQ if a resource shortage has occurred and an SCB is been freed. ahc_pci.c: Turn on cacheline streaming for all controllers that support it. Clarify diagnostic messages about PCI interrupts. |
||
|
Justin T. Gibbs
|
c498406d58 |
Add Perforce RCSIDs for easy revision correlation to my local tree.
ahc_pci.c: Bring back the AHC_ALLOW_MEMIO option at least until the memory mapped I/O problem on the SuperMicro 370DR3 is better understood. aic7xxx.c: If we see a spurious SCSI interrupt, attempt to clear it and continue by unpausing the sequencer. Change the interface to ahc_send_async(). Some async messages need to be broadcast to all the luns of a target or all the targets of a bus. This is easier to achieve by passing explicit channel, target, and lun parameters instead of attempting to construct a device info struct to match. Filter the sync parameters for the PPR message in exactly the same way we do for an old fashioned SDTR message. Correct some typos and correct a panic message. Handle rejected PPR messages. In ahc_handle_msg_reject(), let ahc_build_transfer_msg() build any additional transfer messages instead of doing this inline. aic7xxx.h: Increase the size of both msgout_buf and msgin_buf to better accomodate PPR messages. aic7xxx_freebsd.c: Update for change in ahc_send_async() parameters. aic7xxx_freebsd.h Update for change in ahc_send_async() parameters. Honor AHC_ALLOW_MEMIO. aic7xxx_pci.c: Check the error register before going into full blown PCI interrupt handling. This avoids a few costly PCI configuration space reads when we run our PCI interrupt handler because another device sharing our interrupt line is more active than we are. Also unpause the sequencer after processing a PCI interrupt. |
||
|
Justin T. Gibbs
|
717d424718 |
Move aicasm to its own subdirectory.
Separate our platform independent hooks from core driver functionality shared between platforms (FreeBSD and Linux at this time). Add sequencer workarounds for several chip->chipset interactions. Correct external SCB corruption problem on aic7895 based cards (3940AUW). Lots of cleanups resulting from the port to another OS. |
||
|
Justin T. Gibbs
|
957790c3e6 |
ahc_pci.c:
Disable "cache line streaming" for aic7890/91 Rev A chips. I have never seen these chips fail using this feature, but some of Adaptec's regression tests have. Explicitly set "cache line streaming" to on for aic7896/97 chips. This was happening before, but this documents the fact that these chips will not function correctly without CACHETHEEN set. aic7xxx.h: Add new bug types. Fix a typo in a comment. aic7xxx.reg: Add a definition for the SHVALID bit in SSTAT3 for Ultra2/3 chips. This bit inicates whether the bottom most (current) element in the S/G fifo has exhausted its data count. aic7xxx.seq: Be more careful in how we turn off the secondary DMA channel. Being less careful may hang the PCI bus arbitor that negotiates between the two DMA engines. Remove an unecessary and incorrect flag set operation in the overrun case. On Ultra2/3 controllers, clear the dma FIFO before starting to handle an overrun. We don't want any residual bytes from the beginning of the overrun to cause the code that shuts down the DMA engine from hanging because the FIFO is not (and never will be) empty. If the data fifo is empty by the time we notice that a read transaction has completed, there is no need to hit the flush bit on aic7890/91 hardware that will not perform an auto-flush. Skip some cycles by short circuiting the manual flush code in this case. When transitioning out of data phase, make sure that we have the next S/G element loaded for the following reconnect if there is more work to do. The code would do this in most cases before, but there was a small window where the current S/G element could be exhausted before our fetch of the next S/G element completed. Since the S/G fetch is already initiated at this point, it makes sense to just wait for the segment to arrive instead of incuring even more latency by canceling the fetch and initiating it later. Fast path the end of data phase handling for the last S/G segment. In the general case, we might have worked ahead a bit by stuffing the S/G FIFO with additional segments. If we stop before using them all, we need to fixup our location in the S/G stream. Since we can't work past the last S/G segment, no fixups are ever required if we stop somewhere in that final segment. Fix a little buglet in the target mode dma bug handler. We were employing the workaround in all cases instead of only for the chips that require it. Fix the cause of SCB timeouts and possible "lost data" during read operations on the aic7890. When sending a data on any Ultra2/3 controller, the final segment must be marked as such so the FIFO will be flushed and cleaned up correctly when the transfer is ended. We failed to do this for the CDB transfer and so, if the target immediately transfered from command to data phase without an intervening disconnection, the first segment transferred would be any residual bytes from the cdb transfer. The Ultra160 controllers for some reason were not affected by this problem. Many Thanks to Tor Egge for bringing the aic7890 problem to my attention, providing analysis, as well as a mechanism to reproduce the problem. |
||
|
Justin T. Gibbs
|
c27eebfde8 |
aic7xxx.c:
Correct the BUILD_TCL macro. It was placing the target id in the wrong bits. This was only an issue for adapters that do not perform SCB paging (aha-3940AUW for instance). Don't bother inlining ahc_index_busy_tcl. It is never used in a performance critical path and is a bit chunky. Correct ahc_index_busy_tcl to deal with "busy target tables" embedded in the latter half of 64byte SCBs. Don't initialize the busy target table to its empty state until after we have finished extracting configuration information from chip SRAM. In the common case of using 16 bytes of chip SRAM to do untagged target lookups, we were trashing the last 8 targets configuration data. (actually only target 8 because of the bug in the BUILD_TCL macro). Cram the "bus reset delivered" message back under bootverbose. Fix the cleanup of the SCB busy target table when aborting commands. If the lun is wildcarded, we must loop through all possible luns. aic7xxx.h: Only bother supporting 64 luns right now. It doesn't seem like either this driver or any peripherals will be doing information unit transfers (where the lun number is a 32 bit integer) any time soon. aic7xxx.seq: Fix support for the aic7895. We must flush the data FIFO if performing a manual transfer that is not a multiple of 8 bytes. We were doing this quite regularly for embedded cdbs. Manaually flush the fifo on earlier adapters when dealing with embedded cdbs too. We were stuffing the FIFO with 16 bytes instead, but triggering the flush is more efficient and allows us to remove two instructions from the "copy_to_fifo" routine. |
||
|
Justin T. Gibbs
|
aa6dfd9d3d |
o Convert to <inttypes.h> style fixed sized types to facilitate porting to
other systems. o Normalize copyright text. o Clean up probe code function interfaces by passing around a single structure of common arguments instead of passing "too many" args in each function call. o Add support for the AAA-131 as a SCSI adapter. o Add support for the AHA-4944 courtesy of "Matthew N. Dodd" <winter@jurai.net o Correct manual termination support for PCI cards. The bit definitions for manual termination control in the SEEPROM were incorrect. o Add support for extracting NVRAM information from SCB 2 for BIOSen that use this mechanism to pass this data to OS drivers. o Properly set the STPWLEVEL bit in PCI config space based on the setting in an SEEPROM. o Go back to useing 32byte SCBs for all controllers. The current firmware allows us to embed 12byte cdbs on all controllers in a 32byte SCB, and larger cdbs are rarely used, so it is a better use of this space to offer more SCBs (32). o Add support for U160 transfers. o Add an idle loop executed during data transfers that prefetches S/G segments on controllers that have a secondary DMA engine (aic789X). o Improve the performance of reselections by avoiding an extra one byte DMA in the case of an SCB lookup miss for the reselecting target. We now keep a 16byte "untagged target" array on the card for dealing with untagged reselections. If the controller has external SCB ram and can support 64byte SCBs, then we use an "untagged target/lun" array to maximize concurrency. Without external SCB ram, the controller is limited to one untagged transaction per target, auto-request sense operations excluded. o Correct the setup of the STPWEN bit in SXFRCTL1. This control line is tri-stated until set to one, so set it to one and then set it to the desired value. o Add tagged queuing support to our target role implementation. o Handle the common cases of the ignore wide residue message in firmware. o Add preliminary support for 39bit addressing. o Add support for assembling on big-endian machines. Big-endian support is not complete in the driver. o Correctly remove SCBs in the waiting for selection queue when freezing a device queue. o Now that we understand more about the autoflush bug on the aic7890, only use the workaround on devices that need it. o Add a workaround for the "aic7890 hangs the system when you attempt to pause it" problem. We can now pause the aic7890 safely regardless of what instruction it is executing. |
||
Peter Wemm
|
7b1e0b9c51 | Unused include: #include "ahc.h" | ||
Jake Burkholder
|
e39756439c |
Back out the previous change to the queue(3) interface.
It was not discussed and should probably not happen. Requested by: msmith and others |
||
|
Jake Burkholder
|
740a1973a6 |
Change the way that the queue(3) structures are declared; don't assume that
the type argument to *_HEAD and *_ENTRY is a struct. Suggested by: phk Reviewed by: phk Approved by: mdodd |
||
|
Justin T. Gibbs
|
85ac786b13 |
Kill the "unpause_always" argument to unpause_sequencer(). The reasons
for optimizing the unpause operation no-longer exist, and this is much safer. When restarting the sequencer, reconstitute the free SCB list on the card. This deals with a single instruction gap between marking the SCB as free and actually getting it onto the free list. Reduce the number of transfer negotiations that occur. In the past, we renegotiated after every reported check condition status. This ensures that we catch devices that have unexpectidly reset. In this situation, the target will always report the check condition before performing a data-phase. The new behavior is to renegotiate for any check-condition where the residual matches the orginal data-length of the command (including 0 length transffers). This avoids renegotiations during things like variable tape block reads, where the check condition is reported only to indicate the residual of the read. Revamp the parity error detection logic. We now properly report and handle injected parity errors in all phases. The old code used to hang on message-in parity errors. Correct the reporting of selection timeout errors to the XPT. When a selection timeout occurs, only the currently selecting command is flagged with SELTO status instead of aborting all currently active commands to that target. Fix flipped arguments in ahc_match_scb and in some of the callers of this routine. I wish that gcc allowed you to request warnings for enums passed as ints. Make ahc_find_msg generically handle all message types. Work around the target mode data-in wideodd bug in all non-U2 chips. We can now do sync-wide target mode transfers in target mode across the hole product line. Use lastphase exclusively for handling timeouts. The current phase doesn't take the bus free state into account. Fix a bug in the timeout handler that could cause corruption of the disconnected list. When sending an embedded cdb to a target, ensure that we start on a quad word boundary in the data-fifo. It seems that unaligned stores do not work correctly. |
||
|
Justin T. Gibbs
|
ba09901130 |
Update copyrights to Y2K.
93cx6.c: Make the SRAM dump output a little prettier. aic7xxx.c: Store all SG entries into our SG array in kernel space. This makes data-overrun and other error reporting more useful as we can dump all SG entries. In the past, we only stored the SG entries that the sequencer might need to access, which meant we skipped the first element that is embedded into the SCB. Add a table of chip strings and replace ugly switch statements with table lookups. Add a table with bus phase strings and message reponses to parity errors in those phases. Use the table to pretty print bus phase messages as well as collapse another switch statement. Fix a bug in target mode that could cause us to unpause the sequencer early in bus reset processing. Add the 80MHz/DT mode into our syncrate table. This rate is not yet used or enabled. Correct some comments, clean up some code... aic7xxx.h: Add U160 controller feature information. Add some more bit fields for various SEEPROM formats. aic7xxx.reg: Add U160 register and register bit definitions. aic7xxx.seq: Make phasemis state tracking more straight forward. This avoids the consumption of SINDEX which is a very useful register. For the U160 chips, you must use the 'mov' instruction to update DFCNTRL. Using 'or' to set the PRELOADED bit is completely ineffective. At the end of the command phase, wair for our ACK signal to de-assert before disabling the SCSI dma engine. For slow devices, this avoids clearing the ACK before the other end has had a chance to see it and lower REQ. |
||
|
Justin T. Gibbs
|
41c47eee15 |
Simplify my copyright license terms.
aic7xxx.c: Add a function for sucking firmware out of the controller prior to reset. Remove some inline bloat from functions that should not have been inlined. During initialization, wait 1ms after the chip reset before touching any registers. You can get machine checks on certain architectures (Atari I think?) without the delay. Return CAM_REQ_CMP for external BDR requests instead of CAM_BDR_SENT. Bump some messages to bootverbose levels above 1. Don't clear any negotiated sync rate if the target rejects a WDTR message. The sync rate is only cleared if the target accepts a WDTR message. Fix a small bug in the mesgin handling code that could cause us to believe that we had recieved a message that was actually received by another target. This could only confuse us in some very rare transmission negotiation scenarios. Remove some unecessary cleanup of residual information after a residual is reported. The sequencer does this when the command is queued now. |
||
|
Justin T. Gibbs
|
9be376cc32 |
aic7xxx.c:
Clean out some #if 0'ed debugging cruft. aic7xxx.h: Definitions for the aic7855 and aic7859. |
||
|
Peter Wemm
|
c3aac50f28 | $Id$ -> $FreeBSD$ | ||
|
Justin T. Gibbs
|
7457cf2d46 |
Add support for issuing immediate notify event ccbs for bus resets, bdr
messages, abort messages, and abort tag messages. Fix a bug in how default transfer negotiations are handled if the user had disabled initial bus resets. Support multi-targetid on the aic7895C. |
||
|
Justin T. Gibbs
|
ebada55cce |
aic7xxx.c:
Honor the 'bus reset at startup' option now that the XPT properly handles transfer negotiation in this scenario. Honor the sync rate settings on Ultra2 controllers. We would always negotiate at the fastest speed. Oops. aic7xxx.h: Whitespace. aic7xxx.seq: Fix a minor nit that would cause the controller to miss the update of the negotiation required bitmask causing the negotiation to be delayed by a command. |
||
|
Justin T. Gibbs
|
40ca72018b | Update copyright. Correct some whitespace. | ||
|
Justin T. Gibbs
|
06d2b844cc |
Better workaround for aic7890 chip bug. Use the HS_MAILBOX register to
tell the sequencer to pause itself for a target msg variable update. This avoids the pause race entirely as HS_MAILBOX can be accessed without pausing the chip. 3.2 Merge candidate. |
||
|
Justin T. Gibbs
|
00fa2b1fa7 |
Complete conversion to bus dma. This driver now works on the alpha.
aicasm_symbol.c: Correct an unaligned access problem. You can't rely on DB to store your data in an aligned fashion. |
||
|
Justin T. Gibbs
|
c562189829 |
Keep track of negotiated transfer parameters for each initiator<->target
connection. Clean up support for devices featuring the multiple target SCSI ID feature. On aic7890/91/96/97 chips, we can now assume the target role on multiple target ids simultaneously. Although these chips also have sufficient instruction space to hold to support the initiator and target role at the same time, the initiator role is currently disabled as it will conflict (chip design restriction) with the multi-tid feature. I'll probably add a nob to enable the initiator (there-by disabling multi-tid) some time in the future. Return queue full or busy, depending on the tagged nature of the incoming request, if our command input queue fills up in host memeory. Deal with accept target I/O resource shortages. If we get an underrun on a transaction that wasn't supposed to transmit any data, don't attempt to print out the S/G list. The code would run until hitting a non-present page. (oops) |
||
|
Justin T. Gibbs
|
863c602654 |
Add support for routing initiator transactions to disabled luns to the
black hole device. The controller will now only accept selections if the black hole device is present and some other target/lun is enabled for target mode. Handle the IGNORE WIDE RESIDUE message. This support has not been tested. Checkpoint work on handling ABORT, BUS DEVICE RESET, TERMINATE I/O PROCESS, and CLEAR QUEUE messages as a target. Fix a few problems with tagged command handling in target mode. Wait until the sync offset counter falls to 0 before changing phase after a data-in transfer completes as the DMA logic seems to indicate transfer complete as soon as our last REQ is issued. Simplify some of the target mode message handling code in the sequencer. |
||
|
Justin T. Gibbs
|
0ca48af774 |
Perform a save data pointers operation if a data transfer was performed
in target mode, but we are not completing the command. Use a template of allowed bus arbitration phases to selectively and dynamically enable/disable initiator or target (re)selection. Properly handle timeouts for target role transactions - just go to the bus free state and report the error to the peripheral driver. Checkpoint support for the XPT_ABORT_CCB function code. This currently handles the accept tio and immediate notify ccb types, but does not handle the continue target I/O or SCSI I/O ccb types. This is enough to handle dynamic target enable/disable events. Clean up the SCSI reset code so that we perform at most 1 SCSI bus reset at initialization, the reset requested by the XPT layer. |
||
|
Justin T. Gibbs
|
4dd5dcaecd |
Revamp the way that exceptional message handling is performed so that it
is more robust and common code can be used for both the target and iniator roles. The mechanism for tracking negotiation state has also been simplified. Add support for sync/wide negotiation in target mode and fix many of the target mode bugs running at higher speeds uncovered. Make a first stab at getting all of the bus skew delays correct. Sync+Wide dataout transfers still cause problems, but this may be an initiator problem. Ensure that we exit BITBUCKET mode if the controller is restarted. Add support for target mode only firmware downloads. This has been tested on the aic7880, but should mean that we can perform target mode on any aic7xxx controller. Mixed mode (initiator and target roles in the same firmware load) is currently only supported on the aic7890, but with optimization, may fit on chips with less instruction space. |
||
|
Justin T. Gibbs
|
08c6fbfa40 |
Change the delivery mechanism for incoming target commands. We now
use a 256 entry ring buffer of descriptersfor this purpose. This allows the use of a simple 8bit counter in the sequencer code for tracking start location. Entries in the ring buffer now contain a "cmd_valid" byte at their tail. As an entry is serviced, this byte is cleared by the kernel and set by the sequencer during its dma of a new entry. Since this byte is the last portion of the command touched during a dma, the kernel can use this byte to ensure the command it processes is completely valid. The new command format requires a fixed sized DMA from the controller to deliver which allowed for additional simplification of the sequencer code. The hack that required 1 SCB slot to be stolen for incoming command delivery notification is also gone. |
||
|
Justin T. Gibbs
|
3bafc9d432 |
Massive overhaul of the aic7xxx driver:
- Convert to CAM - Use a new DMA based queuing and paging scheme - Add preliminary target mode support - Add support for the aic789X chips - Take advantage of external SRAM on more controllers. - Numerous bug fixes and performance improvements. |