With this change, the driver tests good (at least on i386):
wb0: <Winbond W89C840F 10/100BaseTX> port 0xb800-0xb87f mem 0xe6800000-0xe680007f irq 12 at device 10.0 on pci0
miibus1: <MII bus> on wb0
amphy0: <Am79C873 10/100 media interface> on miibus1
amphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
wb0: Ethernet address: 00:00:e8:18:2a:02
wb0: link state changed to DOWN
wb0: link state changed to UP
* freebsd-spec.h (FBSD_TARGET_OS_CPP_BUILTINS):
Use builtin_define_with_int_value() instead of
adding a new check for every new major FreeBSD version.
Motivated by: simon
Discussed with: obrien, kan
- Add locked variants of init() and start().
- Use callout_*() to manage callout.
- Test IFF_DRV_RUNNING rather than IFF_UP in wb_intr() to see if we are
still active when an interrupt comes in.
I couldn't find any of these cards anywhere to test on myself, and google
turns up references to FreeBSD and OpenBSD manpages for this driver when
trying to locate a card that way. I'm not sure anyone actually uses these
cards with FreeBSD.
Tested by: NO ONE (despite repeated requests)
I had to initialize the ifnet a bit earlier in attach so that the
if_printf()'s in vr_reset() didn't explode with a page fault.
- Use M_ZERO with contigmalloc() rather than an explicit bzero.
even initialized it, but it never used it.
- Use callout_*() to manage the callout.
- Use m_devget() to copy data out of the rx buffers rather than doing it
all by hand.
- Use m_getcl() to allocate mbuf clusters rather than doing it all by hand.
- Don't free the software descriptor for a rx ring entry if we can't
allocate an mbuf cluster for it. We left a dangling pointer and never
reallocated the entry anyway. OpenBSD's code (from which this was
derived) has the same bug.
Tested by: NO ONE (despite repeated requests)
Reviewed by: wpaul (5)
gdb(1) command better, though I must admit it's confusing: these
files have not only [debugging] symbols, but much more than that.
Requested by: obrien
'device npx' (both of which aren't really optional right now) and
'device io' and 'device mem' (to preserve POLA for 4.x users upgrading
to 6.0) from GENERIC into DEFAULTS.
Requested by: scottl
Reviewed by: scottl
set. When watchdogd(1) is terminated intentionally it clears the bit,
which should then disable it in the kernel.
PR: kern/74386
Submitted by: Alex Hoff <ahoff at sandvine dot com>
Approved by: phk, rwatson (mentor)
directory before the specified config file. This is implemented by
opening DEFAULTS as stdin if it exists, and if so resetting stdin to the
actual config file when DEFAULTS is fully parsed via yywrap(). In short,
this lets us create DEFAULTS kernel configs in /sys/<arch>/conf that can
enable certain options or devices by default and allow users to disable
them via 'nooptions' or 'nodevice' rather than having to create kludge
NO_FOO options.
Requested by: scottl
Reviewed by: scottl
can't acquire an sx lock in ttyinfo() because ttyinfo() can be called
from interrupt handlers (such as atkbd_intr()). Instead, go back to
locking the process group while we pick a thread to display information for
and hold that lock until after we drop sched_lock to make sure the
process doesn't exit out from under us. sched_lock ensures that the
specific thread from that process doesn't go away. To protect against
the process exiting after we drop the proc lock but before we dereference
it to lookup the pid and p_comm in the call to ttyprintf(), we now copy
the pid and p_comm to local variables while holding the proc lock.
This problem was found by the recently added TD_NO_SLEEPING assertions for
interrupt handlers.
Tested by: emaste
MFC after: 1 week
our kernel linker will only load PT_LOAD segments, apparently not.
Instead, produce .dbg objects from .debug objects, and install
them together with non-debug objects, as described in objcopy(1).
Original code by: obrien
debug.kdb.panic and debug.kdb.trap alongside the existing debug.kdb.enter
sysctl. 'panic' causes a panic, and 'trap' causes a page fault. We used
these to ensure that crash dumps succeed from those two common failure
modes. This avoids the need for creating a 'panic' kld module.
* Don't recursively panic if we've already paniced and the local apic is
now stuck.
* Add hw.apic.* tunables/sysctls for extint controls
* Change "lapic%d timer" to "cpu%d timer" intname to match i386
because it sets the floppy controller parameters, which requires O_RDWR.
Specifically, the FD_SOPTS ioctl requires this, and the code errors out
and aborts if it can't do it. Among other things, it is changing the
FDOPT_NOERRLOG flag. Broken in 6.0 as well.
to set the floppy controller parameters, but that requires that the
device node be open in O_RDWR mode now. I think it is broken in 6.0 as
well. This line looks like a stray anyway.
the start of the section headers has to take into account the fact
that the image_nt_header is really variable sized. It happens that
the existing calculation is correct for _most_ production binaries
produced by the Windows DDK, but if we get a binary with oddball
offsets, the PE loader could crash.
Changes from the supplied patch are:
- We don't really need to use the IMAGE_SIZEOF_NT_HEADER() macro when
computing how much of the header to return to callers of
pe_get_optional_header(). While it's important to take the variable
size of the header into account in other calculations, we never
actually look at anything outside the non-variable portion of the
header. This saves callers from having to allocate a variable sized
buffer off the heap (I purposely tried to avoid using malloc()
in subr_pe.c to make it easier to compile in both the -D_KERNEL and
!-D_KERNEL case), and since we're copying into a buffer on the
stack, we always have to copy the same amount of data or else
we'll trash the stack something fierce.
- We need <stddef.h> to get offsetof() in the !-D_KERNEL case.
- ndiscvt.c needs the IMAGE_FIRST_SECTION() macro too, since it does
a little bit of section pre-processing.
PR: kern/83477
