don't implement link power management, LPM.
This fixes error code XHCI_TRB_ERROR_BANDWIDTH for isochronous USB 3.0
transactions.
Submitted by: Horse Ma <Shichun.Ma@dell.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Name each ehci driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/ehci from kernel; already loaded from kernel
A similar fix was done in r333074 but imx_ehci wasn't renamed and generic_ehci wasn't
present at that time.
because it clobbers the super speed link status when a device is in super
speed mode. Currently the power bit is not needed for anything in the USB
hub driver.
This fixes USB warm reset for super speed devices.
Tested by: Shichun.Ma@dell.com
MFC after: 3 days
Sponsored by: Mellanox Technologies
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked). Use it in
preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Reviewed by: hselasky, kib
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D23632
This avoids getting the XHCI_TRB_ERROR_CONTEXT_STATE error code from the XHCI
controller when the endpoint is disabled or already stopped.
Suggested by: Shichun.Ma@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies
The newer versions of RPi FDT flipped the order of the interrupts
specification and added an 'interrupt-names' property for driver aide in
finding the correct interrupt, rather than assuming the positions. Use it if
it's available, or fallback to the old method if there is no interrupt-names
property with a usb value.
This has been tested with both old RPi3B FDT and new RPi3B FDT, USB again
works on the latter.
Reported by: Tom Yan <tom.ty89 gmail com>
MFC after: 3 days
Do not configure any endpoint twice, but instead keep track of which
endpoints are configured on a per device basis, and use an evaluate
endpoint context command instead. When changing the configuration make
sure all endpoints get deconfigured and the configured endpoint mask
is reset.
This fixes an issue where an endpoint might stop working if there is
an error and the endpoint needs to be reconfigured as a part of the
error recovery mechanism in the FreeBSD USB stack.
Tested by: Shichun.Ma@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies
o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't claim All Rights reserved by listing
All Rights Reserved on same line as other copyright holders (but not
me). Other such holders are also listed last where it's clear.
Create an attachment file for the existing ACPI attachment, and create a
new FDT attachment for the generic-ehci driver.
Submitted by: andrew (Original version)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D19389
above 1Kbyte. It might look like some XHCI(4) controllers do not
support when the USB control transfer is split using a link TRB. The
next NORMAL TRB after the link TRB is simply failing with XHCI error
code 4. The quirk ensures we allocate a 64Kbyte buffer so that the
data stage TRB is not broken with a link TRB.
Found at: EuroBSDcon 2019
MFC after: 1 week
Sponsored by: Mellanox Technologies
Ampere eMAG systems have XHCI just described in ACPI, not on PCI.
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: andrew
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D19986
Marvell XHCI is in fact generic-xhci, so move the driver and
add the compatible string.
While here, get and enable the phy if the dtb provide one.
The xhci bindings state that phys should be in a 'phys' property but
Marvell DTS uses 'usb-phy', only add support for 'usb-phy' for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
This is a "fake" phy that handle regulator, clocks and reset gpio.
Only clock and regulator is supported for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
transaction translator will return a NAK. Ignore this message and
retry the complete split instead.
MFC after: 3 days
Sponsored by: Mellanox Technologies
translator, when using the DWC OTG USB controller driver. Make sure to re-try
getting the complete split packets until a DATA0 packet is received. Larger
isochronous frames may be split into multiple MDATA packets terminated
by a single DATA0 packet.
PR: 230434
MFC after: 3 days
Approved by: re (gjb)
Sponsored by: Mellanox Technologies
The last known robust version of this code base was FreeBSD 8.2. There
are no users of this on current, and all users of it have abandoned
this platform or are in legacy mode with a prior version of FreeBSD.
All known users on arm@ approved this removal, and there were no
objections.
Differential Revision: https://reviews.freebsd.org/D16312
Remove all the big-endian arm architectures (ixp425 and ixp435)
support in the kernel and associated drivers.
Differential Revision: https://reviews.freebsd.org/D16257
doing it last. Also, remove the local tracking of whether usb's busdma
memory allocation got done, because it's safe to call the free_all
function even if it wasn't.
through a SYSCTL instead of a compile time define.
Add quirk by default for all LynxPoint XHCI controllers.
PR: 227602
MFC after: 3 days
Sponsored by: Mellanox Technologies
OF_getprop_alloc takes element size argument and returns number of
elements in the property. There are valid use cases for such behavior
but mostly API consumers pass 1 as element size to get string
properties. What API users would expect from OF_getprop_alloc is to be
a combination of malloc + OF_getprop with the same semantic of return
value. This patch modifies API signature to match these expectations.
For the valid use cases with element size != 1 and to reduce
modification scope new OF_getprop_alloc_multi function has been
introduced that behaves the same way OF_getprop_alloc behaved prior to
this patch.
Reviewed by: ian, manu
Differential Revision: https://reviews.freebsd.org/D14850
endpoints. The Allwinner driver will need to set this as the EPINFO
register isn't useful there.
Submitted by: jmcneill
Reviewed by: hselasky
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D5881
On the Allwinner SoCs we need to set a custom endpoint configuration. To
allow for this use a table to store the configuration so the attachment
can override it.
Reviewed by: hselasky
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14783
would be safe, but the function also tries to destroy mutexes that never
got created).
I guess this can only happen when imx_ehci_detach() is called on the
error-exit path from imx_ehci_attach(), and that path never got exercised
before today.
Similarly as other extres pseudo-drivers, implement phy by using kobj model.
This detaches it from provider device, so single device driver can export
multiple different phys. Additionally, this allows phy to be subclassed to
more specialized drivers, like is USB OTG phy, or PCIe phy with hot-plug
capability.
Tested by: manu (previous version, on Allwinner board)
MFC after: 1 month
This reduces noise when kernel is compiled by newer GCC versions,
such as one used by external toolchain ports.
Reviewed by: kib, andrew(sys/arm and sys/arm64), emaste(partial), erj(partial)
Reviewed by: jhb (sys/dev/pci/* sys/kern/vfs_aio.c and sys/kern/kern_synch.c)
Differential Revision: https://reviews.freebsd.org/D10385