new VIA CPUs.
For older CPUs HMAC/SHA1 and HMAC/SHA256 (and others) will still be done
in software.
Move symmetric cryptography (currently only AES-CBC 128/192/256) to
padlock_cipher.c file. Move HMAC cryptography to padlock_hash.c file.
Hardware from: Centaur Technologies
sound cards with optional pseudo-multichannel playback.
It's based on snd_emu10k1 sound driver. Single channel version is available
from audio/emu10kx port since some time.
The two new ALSA header files (GPLed), which contain Audigy 2 ("p16v") and
Audigy 2 Value ("p17v") specific interfaces, are latest versions from ALSA
Mercurial repository.
This is not connected to the build yet.
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
loading for the QLogic cards.
Because isp(4) exists before the root is mounted, it's not really
possible for us to use the kernel's linker to load modules directly
from disk- that's really too bad.
However, the this is still a net win in in that the firmware has
been split up on a per chip (and in some cases, functionality)
basis, so the amount of stuff loaded *can* be substantially less
than the 1.5MB of firmware images that ispfw now manages. That is,
each specific f/w set is now also built as a module. For example,
QLogic 2322 f/w is built as isp_2322.ko and Initiator/Target 1080
firmware is built as isp_1080_it.ko.
For compatibility purposes (i.e., to perturb folks the least), we
also still build all of the firmware as one ispfw.ko module.
This allows us to let 'ispfw_LOAD' keep on working in existing
loader.conf files. If you now want to strip this down to just
the firmware for your h/w, you can then change loader.conf to
load the f/w you specifically want.
We also still allow for ispfw to be statically built (e.g., for
PAE and sparc64).
Future changes will look at f/w unloading and also role switching
that then uses the kernel linker to load different ips f/w sets.
MFC after: 2 months
This driver was ported from OpenBSD by Shigeaki Tagashira
<shigeaki@se.hiroshima-u.ac.jp> and posted at
http://www.se.hiroshima-u.ac.jp/~shigeaki/software/freebsd-nfe.html
It was additionally cleaned up by me.
It is still a work-in-progress and thus is purposefully not in GENERIC.
And it conflicts with nve(4), so only one should be loaded.
yet. More commits to follow.
I got no response from the author, but since the driver is BSD licensed
I don't think he will complain. :-)
I got it from http://people.freebsd.org/~lofi/envy24.tar.gz
Written by: Katsurajima Naoto <raven@katsurajima.seya.yokohama.jp>
s/myri10ge/mxge/g replacement in the myri10ge files. A few contuation
lines were joined because of the regained columns.
- Hook the mxge driver back to the build.
use a different mechanism for setting warning flags, and using
WARNS here only has null or negative effects.
Submitted by: bde (I think it means "submitted")
but large parts are rewritten by matk and tanimura.
This is old code, it's not maintained since 2003. We also don't have a
maintainer for this! Yuriy Tsibizov took it and uses it in his emu10kx
driver. Since the emu10kx driver will enter the tree "soon" (some bugs
have to be fixed after Yuriy return from his holidays), I add it here
already.
This also contains some changes to emu10k1 and cmi, so if you're lucky,
you can now make some kind of use of midi with those soundcards.
To all those poor souls which don't have such a card: feel free to send
patches, we don't have a maintainer for this.
To those which miss a specific feature in the midi code: feel free to
submit patches, we don't have a maintainer for this.
Oh, did I already told that it would be nice if someone would take care
of it? Maintainer with midi equipment wanted! :-)
If you get LOR's, submit a PR and notify multimedia@ please. If you get
panics, submit a PR with a backtrace (compile the sound system into your
kernel instead of using modules in this case) and notify multimedia@
please.
Written by: matk, tanimura
Submitted by: "Yuriy Tsibizov" <Yuriy.Tsibizov@gfk.ru>
Based upon: code from NetBSD
- Linux ioctl support, with the other Linux changes MegaCli
will run if you mount linprocfs & linsysfs then set
sysctl compat.linux.osrelease=2.6.12 or similar. This works
on i386. It should work on amd64 but not well tested yet.
StoreLib may or may not work. Remember to kldload mfi_linux.
- Add in AEN (Async Event Notification) support so we can
get messages from the firmware when something happens.
Not all messages are in defined in event detail. Use
event_log to try to figure out what happened.
- Try to implement something like SIGIO for StoreLib. Since
mrmonitor doesn't work right I can't fully test it. StoreLib
works best with the rh9 base. In theory mrmonitor isn't
needed due to native driver support of AEN :-)
Now we can configure and monitor the RAID better.
Submitted by: IronPort Systems.
lnc(4) on PC98 and i386. The ISA front-end supports the same non-PNP
network cards as lnc(4) did and additionally a couple of PNP ones.
Like lnc(4), the C-bus front-end of le(4) only supports C-NET(98)S
and is untested due to lack of such hardware, but given that's it's
based on the respective lnc(4) and not too different from the ISA
front-end it should be highly likely to work.
- Remove the descriptions of le(4), which where converted from lnc(4),
from sys/i386/conf/NOTES and sys/pc98/conf/NOTES as there's a common
one in sys/conf/NOTES.
Add back in a scheme to emulate old type major/minor numbers via hooks into
stat, linprocfs to return major/minors that Linux app's expect. Currently
only /dev/null is always registered. Drivers can register via the Linux
type shim similar to the ioctl shim but by using
linux_device_register_handler/linux_device_unregister_handler functions.
The structure is:
struct linux_device_handler {
char *bsd_driver_name;
char *linux_driver_name;
char *bsd_device_name;
char *linux_device_name;
int linux_major;
int linux_minor;
int linux_char_device;
};
Linprocfs uses this to display the major number of the driver. The
soon to be available linsysfs will use it to fill in the driver name.
Linux_stat uses it to translate the major/minor into Linux type values.
Note major numbers are dynamically assigned via passing in a -1 for
the major number so we don't need to keep track of them.
This is somewhat needed due to us switching to our devfs. MegaCli
will not run until I add in the linsysfs and mfi Linux compat changes.
Sponsored by: IronPort Systems
o Properly use rman(9) to manage resources. This eliminates the
need to puc-specific hacks to rman. It also allows devinfo(8)
to be used to find out the specific assignment of resources to
serial/parallel ports.
o Compress the PCI device "database" by optimizing for the common
case and to use a procedural interface to handle the exceptions.
The procedural interface also generalizes the need to setup the
hardware (program chipsets, program clock frequencies).
o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by
default and non-serdev devices are handled by the bus.
o Use the serdev I/F to collect interrupt status and to handle
interrupts across ports in priority order.
o Sync the PCI device configuration to include devices found in
NetBSD and not yet merged to FreeBSD.
o Add support for Quatech 2, 4 and 8 port UARTs.
o Add support for a couple dozen Timedia serial cards as found
in Linux.
This driver was generously developed and donated by Highpoint.
It is enabled for i386 only at the moment. I will enable it for amd64
shortly.
Obtained from: HighPoint Technologies, Inc.
o Add the scc(4) manpage to the build.
o Update the uart(4) manpage to account for scc(4).
o Update the uart(4) module build to include support for scc(4).
controllers typically have multiple channels and support a number
of serial communications protocols. The scc(4) driver is itself
an umbrella driver that delegates the control over each channel
and mode to a subordinate driver (like uart(4)).
The scc(4) driver supports the Siemens SAB 82532 and the Zilog
Z8530 and replaces puc(4) for these devices.
is derived from the phrase 'MegaRAID Firmware Interface' used by LSI. This
driver provides a block interface to logical disks on the card and a minimal
management device. It is MPSAFE, INTR_FAST, and 64-bit capable.
Thanks to Dell for providing hardware to test with and IronPort for
sponsoring the work.
Sponsored by: Dell, Ironport
MFC After: 3 days
- <netipx> headers [1]
- IPX library (libipx)
- IPX support in ifconfig(8)
- IPXrouted(8)
- new MK_NCP option
New MK_NCP build option controls:
- <netncp> and <fs/nwfs> headers
- NCP library (libncp)
- ncplist(1) and ncplogin(1)
- mount_nwfs(8)
- ncp and nwfs kernel modules
User knobs: WITHOUT_IPX, WITHOUT_IPX_SUPPORT, WITHOUT_NCP.
[1] <netsmb/netbios.h> unconditionally uses <netipx> headers
so they are still installed. This needs to be dealt with.
which is normal for own files of a device driver.
DEV_FOO should be used if an unrelated kernel file needs to know of
the `foo' driver's static presence. Obviously, module source files
should never use DEV_*.
enabled by default in NETSMB and smbfs.ko.
With the most of modern SMB providers requiring encryption by
default, there is little sense left in keeping the crypto part
of NETSMB optional at the build time.
This will also return smbfs.ko to its former properties users
are rather accustomed to.
Discussed with: freebsd-stable, re (scottl)
Not objected by: bp, tjr (silence)
MFC after: 5 days
into a separate module. Accordingly, convert the option into a device
named similarly.
Note for MFC: Perhaps the option should stay in RELENG_6 for POLA reasons.
Suggested by: scottl
Reviewed by: cokane
MFC after: 5 days
and want to have crypto support loaded as KLD. By moving zlib to separate
module and adding MODULE_DEPEND directives, it is possible to use such
configuration without complication. Otherwise, since IPSEC is linked with
zlib (just like crypto.ko) you'll get following error:
interface zlib.1 already present in the KLD 'kernel'!
Approved by: cognet (mentor)
Otherwise a kernel build would break in the coda5 module if the main
kernel conf file enabled CODA_COMPAT_5, too. Redefined symbols are
strictly disallowed by -Werror.
To overcome this issue, introduce a different symbol indicating coda5
build, CODA5_MODULE, and translate it to CODA_COMPAT_5 appropriately
in /sys/coda/coda.h.
MFC after: 3 days
inside !if defined(KERNBUILDDIR).
Utilize the fact the module will support all frames by default --
it needs no ETHER_* options unless some frames need to be disabled.
Fix the comment respectively.
Don't forget to create fake opt_ef.h if no ETHER_* are set.
MFC after: 3 days
More info regarding these nics can be found at http://www.myri.com.
Please note that the files
sys/dev/myri10ge/{mcp_gen_header.h,myri10ge_mcp.h} are internally
shared between all our drivers (solaris, macosx, windows, linux, etc).
I'd like to keep these files unchanged, so I can just import newer
versions of them when the firmware API/ABI changes. This means I'm
stuck with some of the crazy-long #define names, and possibly
non-style(9) characteristics of these files.
Many thanks to mlaier for doing firmware(9) just as I
needed it, and to scottl for his helpful review.
Reviewed by: scottl, glebius
Sponsored by: Myricom Inc.
Without CODA_COMPAT_5, it would be equivalent to the plain coda
module. Therefore just add -DCODA_COMPAT_5 to CFLAGS instead of
fiddling with opt_coda.h. This is particularly important when
the module is built along with the kernel and CODA_COMPAT_5 isn't
in the kernel conf file (and so not in opt_coda.h either).
MFC after: 3 days
nfs_diskless.c if NFS_ROOT is in effect, e.g., present
in the kernel config file. Otherwise the built module
won't load due to an undefined reference to nfs_setup_diskless.
MFC after: 3 days
to work with ipmitools. It works with other tools that have an OpenIPMI
driver interface. The port will need to get updated to used this.
I have not implemented the IPMB mode yet so ioctl's for that don't
really do much otherwise it should work like the OpenIPMI version.
The ipmi.h definitions was derived from the ipmitool header file.
The bus attachments are done for smbios and pci/smbios. Differences
in bus probe order for modules/static are delt with. ACPI attachment
should be done.
This drivers registers with the watchdod(4) interface
Work to do:
- BT interface
- IPMB mode
This has been tested on Dell PE2850, PE2650 & PE850 with i386 & amd64
kernel.
I will link this into the build on next week.
Tom Rhodes, helped me with the man page.
Sponsored by: IronPort Systems Inc.
Inspired from: ipmitool & Linux
in order to support the on-board LANCE in Ultra 1 and to the MI NOTES as
it should work just fine with the AMD PCnet family of chips on all archs
but is not yet meant to replace lnc(4). If a kernel includes all of le(4),
lnc(4) and pcn(4) precedence is given to lnc(4)/pcn(4) for now.
specially crafted module. There are several handrolled sollutions to this
problem in the tree already which will be replaced with this. They include
iwi(4), ipw(4), ispfw(4) and digi(4).
No objection from: arch
MFC after: 2 weeks
X-MFC after: some drivers have been converted
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.
Add in the Linux IOCTL shim and create the megadev0 device so
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.
Add glue to build the modules but don't tie it into the build
yet until I test it from the CVS repo. via the mirror on an
amd64 machine.
Tie this into the Linux32 emulation on amd64 so the tools can
run on amd64 kernel.
Cleaned up by: ps (amr_linux.c)
This is based on MCPC USB mobile phone guide line (MCPC-GL005)
Some other 3G system or so will work with this driver.
Kyocera PHS terminal (a.k.a. Kyopon) is known to work, which
is now supported by umodem(4) driver.
