syncing for Hummingbird and Sabre bridges should be applied with every
BUS_DMASYNC_POSTREAD instead of in a wrapper around interrupt handlers
for devices behind PCI-PCI bridges only as suggested by the documentation
(code for the latter actually exists in OpenSolaris but is disabled by
default), which also makes more sense.
- Take advantage of the ofw_pci_setup_device method introduced in r220038
for disabling bus parking for certain EBus bridges in order to
- Mark some unused parameters as such.
work.
- Sanity check the parameters passed to the implementations of the
pcib_{read,write}_config() methods. Using illegal values can cause
no real harm but it doesn't hurt to avoid unnecessary data error
traps requiring to flush and re-enable the level 1 caches.
- Failing to register as interrupt controller during attach shouldn't
be fatal so just inform about this instead of panicing.
- Disable rerun of the streaming cache as workaround for a silicon bug
of certain Psycho versions.
- Remove the comment regarding lack of newbus'ified bus_dma(9) as being
able to associate a DMA tag with a device would allow to implement
CDMA flushing/syncing in bus_dmamap_sync(9) but that would totally
kill performance. Given that for devices not behind a PCI-PCI bridge
the host-to-PCI bridges also only do CDMA flushing/syncing based on
interrupts there's no additional disadvantage for polling(4) callbacks
in the case schizo(4) has to do the CDMA flushing/syncing but rather a
general problem.
- Don't panic if the power failure, power management or over-temperature
interrupts doesn't exist as these aren't mandatory and not available
with all controllers (not even Psychos). [1]
- Take advantage of KOBJMETHOD_END.
- Remove some redundant variables.
- Add missing const.
PR: 131371 [1]
have separate configuration spaces so by definition they implement
different PCI domains. Thus change psycho(4) to use PCI domains
instead of reenumerating all PCI busses so they have globally unique
bus numbers and drop support for reenumerating busses in the OFW PCI
code.
According to CVS history reenumeration was also required in order to
get some E450 to boot but given that no other open source kernel
changes the PCI bus numbers assigned by the firmware I believe the
real problem was that the old code used the bus number as the device
number for the PCI busses and unlike most of the other machines the
firmwares of the problematic ones don't use disjoint PCI bus numbers
across the host-PCI-bridges.
MFC after: 1 month
is required by the X.Org PCI domains code and additionally needs
a workaround for Hummingbird and Sabre bridges as these don't
allow their config headers to be read at any width, which is an
unusual behavior.
- In psycho(4) take advantage of DEFINE_CLASS_0 and use more
appropriate types for some softc members.
MFC after: 3 days
allowing it to be a filter/"fast" handler. Locking the interrupt
handlers with a spin lock is mainly a requirement in schizo(4)
but as we ought to register the spin lock anyway it should not
hurt to take advantage of it in psycho(4).
- Pass both a driver_filter_t and a driver_intr_t argument to
psycho_set_intr(), allowing to get rid of the FAST interrupt
flag hack.
- Don't register the over-temperature interrupt handler as filter/
"fast" handler so shutdown_nice() can acquire the process lock.
- Use bus_{read,write}_8() instead of bus_space_{read,write}_8()
in order to get rid of sc_bushandle and sc_bustag in the softc.
- Correct the debug output for adjusting the subordinate bus number.
- Remove the banal and outdated above psycho_filter_stub().
- Fix some white space nits.
sun4v nexus(4) in turn is based on):
o Change nexus(4) to manage the resources of its children so the
respective device drivers don't need to figure them out of OFW
themselves.
o Change nexus(4) to provide the ofw_bus KOBJ interface instead of
using IVARs for supplying the OFW node and the subset of standard
properties of its children. Together with the previous change this
also allows to fully take advantage of newbus in that drivers like
fhc(4), which attach on multiple parent busses, no longer require
different bus front-ends as obtaining the OFW node and properties
as well as resource allocation works the same for all supported
busses. As such this change also is part 4/4 of allowing creator(4)
to work in USIII-based machines as it allows this driver to attach
on both nexus(4) and upa(4). On the other hand removing these IVARs
breaks API compatibility with the powerpc nexus(4) but which isn't
that bad as a) sparc64 currently doesn't share any device driver
hanging off of nexus(4) with powerpc and b) they were no longer
compatible regarding OFW-related extensions at the pci(4) level
since quite some time.
o Provide bus_get_dma_tag methods in nexus(4) and its children in
order to handle DMA tags in a hierarchical way and get rid of the
sparc64_root_dma_tag kludge. Together with the previous two items
this changes also allows to completely get rid of the nexus(4)
IVAR interface. It also includes:
- pushing the constraints previously specified by the nexus_dmatag
down into the DMA tags of psycho(4) and sbus(4) as it's their
IOMMUs which induce these restrictions (and nothing at the
nexus(4) or anything that would warrant specifying them there),
- fixing some obviously wrong constraints of the psycho(4) and
sbus(4) DMA tags, which happened to not actually be used with
the sparc64_root_dma_tag kludge in place and therefore didn't
cause problems so far,
- replacing magic constants for constraints with macros as far
as it is obvious as to where they come from.
This doesn't include taking advantage of the newbus way to get
the parent DMA tags implemented by this change in order to divorce
the IOTSBs of the PCI and SBus IOMMUs or for implementing the
workaround for the DMA sync bug in Sabre (and Tomatillo) bridges,
yet, though.
o Get rid of the notion that nexus(4) (mostly) reflects an UPA bus
by replacing ofw_upa.h and with ofw_nexus.h (which was repo-copied
from ofw_upa.h) and renaming its content, which actually applies to
all of Fireplane/Safari, JBus and UPA (in the host bus case), as
appropriate.
o Just use M_DEVBUF instead of a separate M_NEXUS malloc type for
allocating the device info for the children of nexus(4). This is
done in order to not need to export M_NEXUS when deriving drivers
for subordinate busses from the nexus(4) class.
o Use the DEFINE_CLASS_0() macro to declare the nexus(4) driver so
we can derive subclasses from it.
o Const'ify the nexus_excl_name and nexus_excl_type arrays as well
as add 'associations' and 'rsc', which are pseudo-devices without
resources and therefore of no real interest for nexus(4), to the
former.
o Let the nexus(4) device memory rman manage the entire 64-bit address
space instead of just the UPA_MEMSTART to UPA_MEMEND subregion as
Fireplane/Safari- and JBus-based machines use multiple ranges,
which can't be as easily divided as in the case of UPA (limiting
the address space only served for sanity checking anyway).
o Use M_WAITOK instead of M_NOWAIT when allocating the device info
for children of nexus(4) in order to give one less opportunity
for adding devices to nexus(4) to fail.
o While adapting the drivers affected by the above nexus(4) changes,
change them to take advantage of rman_get_rid() instead of caching
the RIDs assigned to allocated resources, now that the RIDs of
resources are correctly set.
o In iommu(4) and nexus(4) replace hard-coded functions names, which
actually became outdated in several places, in panic strings and
status massages with __func__. [1]
o Use driver_filter_t in prototypes where appropriate.
o Add my copyright to creator(4), fhc(4), nexus(4), psycho(4) and
sbus(4) as I changed considerable amounts of these drivers as well
as added a bunch of new features, workarounds for silicon bugs etc.
o Fix some white space nits.
Due to lack of access to Exx00 hardware, these changes, i.e. central(4)
and fhc(4), couldn't be runtime tested on such a machine. Exx00 are
currently reported to panic before trying to attach nexus(4) anyway
though.
PR: 76052 [1]
Approved by: re (kensmith)
INO) for incorrect interrupt map entries on E250 machines. These
incorrect entries caused the INO of the on-board HME to be also
assigned to the second on-board NS16550 and to the on-board printer
port controller. Further down the road caused hme(4) to fail to attach
to the on-board HME in FreeBSD 5 and 6 as INTR_FAST and non-INTR_FAST
handlers can't share the same IRQ there (it's unknown what whould
happen in -CURRENT now that INTR_FAST and non-INTR_FAST handlers can
share an IRQ but I'd expect funny problems with uart(4)).
- Make sure there are exactly 4 PCI ranges instead of just checking
that the bridge has a 'ranges' property in the OFW device tree at all.
Besides the fact that currently the 64bit memory range isn't used by
this driver it we can't really work with less than 4 ranges and don't
have memory for more than 4 bus handles for the ranges in the softc.
- Remove sc_range and sc_nrange from softc; for the bridges supported
by this driver we no longer need to know the ranges besides the bus
handles obtained from them once this driver is attached. That way we
also can free the memory allocated for sc_range during attach again.
- Remove sc_dvmabase from the softc and pass it to psycho_iommu_init()
via an additional argument as we no longer need to know the DVMA base
in this driver once the IOMMU is initialized.
- Remove sc_dmatag from the softc, there isn't much sense in keeping
the nexus dma tag around locally.
PR: 88279 [1]
Info from: OpenSolaris [1]
Tested by: kensmith [1]
MFC after: 1 month
between this driver and other Host-PCI bridge drivers based on this one:
- Make the code fit into 80 columns.
- Make the code adhere style(9) (don't use function calls in initializers,
use uintXX_t instead of u_intXX_t, add missing prototypes, ...).
- Remove unused and superfluous struct declaration, softc member, casts,
includes, etc.
- Use FBSDID.
- Sprinkle const.
- Try to make comments and messages consistent in style throughout the
driver.
- Use convenience macros for the number of interrupts and ranges of the
bridge.
- Use __func__ instead of hardcoded function names in panic strings and
error messages. Some of the hardcoded function names actually were
outdated through moving code around. [1]
- Rename softc members related to the PCI side of the bridge to sc_pci_*
in order to make it clear which side of the bridge they refer to (so
stuff like sc_bushandle vs. sc_bh is less confusing while reading the
code).
PR: 76052 [1]
"options OFW_NEWPCI").
This is a bit overdue, the new sparc64 OFW PCI code which is
meant to replace the old one is in place for 10 months and
enabled by default in GENERIC for 8 months. FreeBSD 5.2 and
5.2.1 also shipped with the new code enabled by default.
- Some minor clean-up, e.g. remove functions that encapsulated
the #ifdefs for OFW_NEWPCI, remove unused resp. no longer
required includes, etc.
Approved by: tmm, no objections on freebsd-sparc64
- Fix some comments; remove numerous superfluous or outdated ones.
- Correctly pass on the requesting device when handing requests up
to the parent bus.
- Use the complete device name, including unit number, to build the
IOMMU instance name.
- Inline a function that was only used once, and was trivial.
for now. It introduces a OFW PCI bus driver and a generic OFW PCI-PCI
bridge driver. By utilizing these, the PCI handling is much more elegant
now.
The advantages of the new approach are:
- Device enumeration should hopefully be more like on Solaris now,
so unit numbers should match what's printed on the box more
closely.
- Real interrupt routing is implemented now, so cardbus bridges
etc. have at least a chance to work.
- The quirk tables are gone and have been replaced by (hopefully
sufficient) heuristics.
- Much cleaner code.
There was also a report that previously bogus interrupt assignments
are fixed now, which can be attributed to the new heuristics.
A pitfall, and the reason why this is not the default yet, is that
it changes device enumeration, as mentioned above, which can make
it necessary to change the system configuration if more than one
unit of a device type is present (on a system with two hme cars,
for example, it is possible that hme0 becomes hme1 and vice versa
after enabling the option). Systems with multiple disk controllers
may need to be booted into single user (and require manual specification
of the root file system on boot) to adjust the fstab.
Nevertheless, I would like to encourage users to use this option,
so that it can be made the default soon.
In detail, the changes are:
- Introduce an OFW PCI bus driver; it inherits most methods from the
generic PCI bus driver, but uses the firmware for enumeration,
performs additional initialization for devices and firmware-specific
interrupt routing. It also implements an OFW-specific method to allow
child devices to get their firmware nodes.
- Introduce an OFW PCI-PCI bridge driver; again, it inherits most
of the generic PCI-PCI bridge driver; it has it's own method for
interrupt routing, as well as some sparc64-specific methods (one to
get the node again, and one to adjust the bridge bus range, since
we need to reenumerate all PCI buses).
- Convert the apb driver to the new way of handling things.
- Provide a common framework for OFW bridge drivers, used be the two
drivers above.
- Provide a small common framework for interrupt routing (for all
bridge types).
- Convert the psycho driver to the new framework; this gets rid of a
bunch of old kludges in pci_read_config(), and the whole
preinitialization (ofw_pci_init()).
- Convert the ISA MD part and the EBus driver to the new way
interrupts and nodes are handled.
- Introduce types for firmware interrupt properties.
- Rename the old sparcbus_if to ofw_pci_if by repo copy (it is only
required for PCI), and move it to a more correct location (new
support methodsx were also added, and an old one was deprecated).
- Fix a bunch of minor bugs, perform some cleanups.
In some cases, I introduced some minor code duplication to keep the
new code clean, in hopes that the old code will be unifdef'ed soon.
Reviewed in part by: imp
Tested by: jake, Marius Strobl <marius@alchemy.franken.de>,
Sergey Mokryshev <mokr@mokr.net>,
Chris Jackman <cjackNOSPAM@klatsch.org>
Info on u30 firmware provided by: kris
This machine uses a non-standard scheme to specify the interrupts to
be assigned for devices in PCI slots; instead of giving the INO
or full interrupt number (which is done for the other devices in this
box), the firmware interrupt properties contain intpin numbers, which
have to be swizzled as usual on PCI-PCI bridges; however, the PCI host
bridge nodes have no interrupt map, so we need to guess the
correct INO by slot number of the device or the closest PCI-PCI
bridge leading to it, and the intpin.
To do this, this fix makes the following changes:
- Add a newbus method for sparc64 PCI host bridges to guess
the INO, and glue code in ofw_pci_orb_callback() to invoke it based
on a new quirk entry. The guessing is only done for interrupt numbers
too low to contain any IGN found on e450s.
- Create another new quirk entry was created to prevent mapping of EBus
interrupts at PCI level; the e450 has full INOs in the interrupt
properties of EBus devices, so trying to remap them could cause
problems.
- Set both quirk entries for e450s; remove the no-swizzle entry.
- Determine the psycho half (bus A or B) a driver instance manages
in psycho_attach()
- Implement the new guessing method for psycho, using the slot number,
psycho half and property value (intpin).
Thanks go to the testers, especially Brian Denehy, who tested many kernels
for me until I had found the right workaround.
Tested by: Brian Denehy <B.Denehy@90east.com>, jake, fenner,
Marius Strobl <marius@alchemy.franken.de>,
Marian Dobre <mari@onix.ro>
Approved by: re (scottl)
- tweak the announce message a bit
- remove '\n's from a few panic() calls
- don't use the DVMA base adress the firmware reports; instead, figure
it out from the appropriate register on Sabres and let the IOMMU code
choose it on Psychos. This also makes the IOMMU TSB size freely
selectable.
the bus-dependent code and to be able to support more systems. The core
of the new code is mostly obtained from NetBSD.
Kluge the interrupt routing methods of the psycho and apb drivers so
that an intline of 0 can be handled for now; real routing is still not
possible (all intline registers are preinitialized instead); this will
require a sparc64-specific adaption of the driver for generic PCI-PCI
bridges with a custom routing method to work right.
struct ofw_nexus_reg. Implement UPA device memory management in the
nexus driver.
Adapt the psycho driver to these changes, and do some minor cleanup work
while being there.
