respectivly. This will allow one to have a kernel with both devices
present and use it for multiple boards with different types of RTC
sitting on a bus.
Discussed with: imp
number of queued packets in watchdog timeout handler. If there are
no queued packets just print a informational message and return
without resetting controller. Also fix to invoke correct Tx
completion handler as 3C905B needs different handler.
Previously it used to clear the flag only when the transmit queue
is empty which may slow down Tx performance.
While I'm here check whether driver is running and whether we can
queue more packets in if_start handler. This fixes occasional
watchdog timeouts.
Reported by: xer < xernet <> hotmail dot it >
Tested by: xer < xernet <> hotmail dot it >
checksum offload frames. Software workaround used for broken
controllers(RTL8169, RTL8168, RTL8168B) seem to cause watchdog
timeouts on RTL8139C+.
Introduce a new flag RL_FLAG_AUTOPAD to mark automatic padding
feature of controller and set it for RTL8139C+ and controllers that
use new descriptor format. This fixes watchdog timeouts seen on
RTL8139C+.
Reported by: Dimitri Rodis < DimitriR <> integritasystems dot com >
Tested by: Dimitri Rodis < DimitriR <> integritasystems dot com >
registers.
- Cleanup PCI-X capability printf to not leave a dangling "supports" for
some PCI-X bridges.
- Display additional PCI express details including the negotiated and max
link width and the actual and maximum supported max payload.
MFC after: 1 month
when polled mode is enabled. This should help with duplicated/missing
characters problem at mountroot, geli, etc. prompts on multi CPU systems
while kbdmux(4) is enabled.
Tested by: Tobias Grosser <grosser -at- fim -dot- uni-passau -dot- de>
Tested by: Fabian Keil <freebsd-listen -at- fabiankeil -dot- de>
MFC after: 3 days
network load.
1. Leave the RX interrupt routine if there is no mbuf available.
2. Properly initialize and track tx_desc_used_count counter so as not to
leak mbuf while traversing used descriptors.
Obtained from: Semihalf
- Remove redundant softc members for RIDs.
- Change some softc members to be unsigned where more appropriate.
- Add some missing const.
- Remove support for mmap(2)'ing VGA I/O as it was broken [1] and
not required by X.Org anyway.
- Fix some confusion between bus, physical and virtual addresses
which mostly consisted in using members of struct video_adapter
inappropriately but wasn't fatal except for the regular framebuffer
mmap(2)'ing.
- Remove redundant bzero(9)'ing of the softc.
- Don't map the framebuffer twice in case the firmware has already
mapped it as besides wasting resources this isn't possible with
all MMUs. This is a bit tricky as a) just because the firmware
provides a property with a virtual address doesn't mean it's
actually mapped (but typically is when the framebuffer is the
console) and b) the firmware doesn't necessarily map the it with
the same byteorder as we do. This make machfb(4) work on machines
with cheetah-class MMUs (including X.Org).
Reported by: Michael Plass [1]
MFC after: 3 days
addresses to BARs into new pci_read_bar() and pci_write_bar() routines.
pci_add_map(), pci_alloc_map(), and pci_delete_resource() now use these
routines to work with BARs.
- Just pass the device_t for the new PCI device to various routines instead
of passing the device, bus, slot, and function.
Reviewed by: imp
Remote host can advertise smaller MSS than that of sender so upper
stack might have adjusted the MSS which in turn generates IP
packets that are less size than that of interface MTU.
Reported by: Bjoern Koenig ( bkoenig <> alpha-tierchen dot de )
Tested by: Bjoern Koenig ( bkoenig <> alpha-tierchen dot de )
MFC after: 3 days
TCPSTAT_INC(), rather than directly manipulating the fields across the
kernel. This will make it easier to change the implementation of
these statistics, such as using per-CPU versions of the data structures.
MFC after: 3 days
1) Flag it and only access that command on the 3c1
2) The TX PLL appears to power down when not in use, so we have to power
it back up when we've been idle. Do this at the start of ifstart.
Otherwise we fall off the net.
have other media to test against, I've left that media reporting
unchanged.
o Enable the TX_PLL when we enable TX. This is harmless on most
cards, but required to get the 3c1 CF card working. Power savings
could be had by managing this better, but for now it gets my card
working.
We typically wire translation to devices with TLB1 entries and
pmap_kextract() does not know about those and returns 0. This
causes false positives (read: all serial ports suddenly become
the console).
Do not use Giant for kbdmux(4) locking. This is wrong and apparently
causing more problems than it solves. This will re-open the issue
where interrupt handlers may race with kbdmux(4) in polling mode.
Typical symptoms include (but not limited to) duplicated and/or
missing characters when low level console functions (such as gets)
are used while interrupts are enabled (for example geli password
prompt, mountroot prompt etc.)
MFC after: 3 days
(framing, parity, etc), but does not indicate characters
being received. Since no chracters have been received,
ignore the line errors.
PR: 131006
MFC after: 3 days
instead of just register one for the first adapter. Without doing this
there would be some data loss upon shutdown because data could be ignored
when flushing to disk.
MFC after: 3 days
- override_kernel_driver() has been removed since this is an
in-tree version of driver.
- __DATE__ and __TIME__ removed from version string to make
binary update builders happy.
- Utilize pause(9) for __FreeBSDversion >= 700033 (redo 167086).
- Utilize kproc_suspend_check() for __FreeBSDversion >= 800002.
(redo 172836).
- Don't read past end of pVDevice (redo 143787).
- Make sure that controller and channel are initialized (redo 169823).
- Don't include cam/cam_xpt_periph.h (redo 158177).
MFC After: 3 days
and update comments about original patches doing this and it not
working. It works for both the DL10019 and DL10022 based cards that I
have. It really helps the DL10019 cards, since they were using 8k
instead of the normal 16k that regular NE-2000 cards help.
# Note to self: need to provide a common routine to setup memory
# parameters.
DP8390-based cards have no generic way of reporting status of the link
or setting the media type. Some specific versions of these cards do,
however, allow for this, and we already support some of them. Make
the 'ed' experience more uniform by providing "autoselect" as the
meida and status "active" always. This won't affect the chips that
provide more specific details.
It makes little sense to use 100 Hz polling in dcons. We cannot live
without polling, because that's just how dcons works. It polls the
buffer filled by the firewire hardware. 25 Hz is probably enough for
most use cases.
Discussed with: rwatson
Tested by: kan
dcons_drv_init invocations. Testing return value for 0 does not work for
cases where dcons_drv_init was called already as part of low level
console initialization.
Refactor how we interface with the root HUB. This is achieved by making a
direct call from usb2_do_request to the host controller for root hub requests,
this call will perform the controller specific register read/writes and return
the error code.
This cuts out a lot of code in the host controller files and saves one thread
per USB bus.
Submitted by: Hans Petter Selasky
- add support for more complicated HID descriptors which can have multiple
definitions of the same field.
- remove old modulo patch in ums, which I think is due to bad HID parsing,
which should be fixed now.
Reported by: netchild
Submitted by: Hans Petter Selasky
Some cancelable flags are always true. Substitute these away. These cancelable
flags were mostly useful with the root HUB which is now handled differently.
Submitted by: Hans Petter Selasky
Refactor how we interface with the root HUB. This cuts around 1200 lines of
code totally and saves one thread per USB bus.
Submitted by: Hans Petter Selasky
