Features:
- configurable amount of days between scrubs (default value or per pool)
- do not scrub directly after pool creation (respects the configured
number of days between scrubs)
- do not scrub if a scrub is in progress
- tells how to see the status of the scrub
- tells how many days since the last scrub if it skips the scrubbing
- warns if a non-existent pool is specified explicitely
(default: no pools specified -> all currently imported pools are
handled)
- runs late in the periodic run to not slow down the other periodic daily
scripts
Discussed on: fs@
This avoids errors or __DECONST() from places with higher WARNS levels.
Adjust a local cache variable in ipcs to const as well
to compile in the new world order.
Suggested by: jhb
Reviewed by: jhb, kib, brueffer (man)
mount(8): add xref to devfs(5)
devfs(5): change example to something more likely to be useful (it is not
necessary to mount a devfs on /dev manually, but for chroots/jails it is
often needed), mention since when devfs is preferred to device nodes on ufs
PR: 146600
MFC after: 2 weeks
bottom of the manpages and order them consistently.
GNU groff doesn't care about the ordering, and doesn't even mention
CAVEATS and SECURITY CONSIDERATIONS as common sections and where to put
them.
Found by: mdocml lint run
Reviewed by: ru
Although groff_mdoc(7) gives another impression, this is the ordering
most widely used and also required by mdocml/mandoc.
Reviewed by: ru
Approved by: philip, ed (mentors)
and ipv6_ifconfig_<interface> options have already been deprecated,
these changes do not alter that.
With these changes any value set for ipv6_enable will emit a
warning. In order to avoid a POLA violation for the deprecation
of the option ipv6_enable=NO will still disable configuration
for all interfaces other than lo0. ipv6_enable=YES will not have
any effect, but will emit an additional warning. Support and
warnings for this option will be removed in FreeBSD 10.x.
Consistent with the current code, in order for IPv6 to be configured
on an interface (other than lo0) an ifconfig_<interface>_ipv6
option will have to be added to /etc/rc.conf[.local].
1. Clean up and minor optimizations for the following functions:
ifconfig_up (the ipv6 elements)
ipv6if
ipv6_autoconfif
get_if_var
_ifconfig_getargs
The cleanups generally were to move the "easy" tests earlier in the
functions, and consolidate duplicate code.
2. Stop overloading ipv6_prefer with the ability to disable IPv6
configuration.
3. Remove noafif() which was only ever called from ipv6_autoconfif.
Instead, simplify and integrate the tests into that function, and
convert the test to use is_wired_interface() instead of listing
wireless interfaces explicitly.
4. Integrate backwards compatibility for ipv6_ifconfig_<interface>
into _ifconfig_getargs. This dramatically simplifies the code in
all of the callers, and avoids a lot of other code duplication.
5. In rc.d/netoptions, add code for an ipv6_privacy option to use
RFC 4193 style pseudo-random addresses (this is what windows does
by default, FYI).
6. Add support for the [NO]RTADV options in ifconfig_getargs() and
ipv6_autoconfif(). In the latter, include support for the explicit
addition of [-]accept_rtadv in ifconfig_<interface>_ipv6 as is done
in the current code.
7. In rc.d/netif add a warning if $ipv6_enable is set, and remove
the set_rcvar_obsolete for it. Also remove the latter from
rc.d/ip6addrctl.
8. In /etc/defaults/rc.conf:
Add an example for RTADV configuration.
Set ipv6_network_interfaces to AUTO.
Switch ipv6_prefer to YES. If ipv6_enable is not set this will have
no effect.
Add a default for ipv6_privacy (NO).
9. Document all of this in rc.conf.5.
Note that this is actually a no-op for most users, as this GNU
cpio was broken on -HEAD and 8-STABLE since last March until
the recent fix.
FreeBSD 8.0+ uses BSD cpio by default and the code is being
actively maintained.
Blessed by: kientzle
With hat: secteam
MFC after: 3 days
At least in RELENG_7 this fixes some start problems for some programs
from the ports. It is also more correct, as a jail shall not expect
input (interactivity) from the jail-host.
Revert the current behavior of starting jails in the background and
make it optional only for the start of jails (jail_parallell_start=YES
in rc.conf):
- The stop can not be done in the background, the system needs to wait
until everything is stopped correctly before it can reboot or power
down.
- The start should not be done in parallel by default, this not only
breaks POLA for people comming from RELENG_x, it may also break a
dependency chain with other scripts in the jail-host, which need to
do some stuff after the jails are up and running (e.g. hardlinking
a mysql socket from one jail into another one).
Discussed on: freebsd-jails@
HAST allows to transparently store data on two physically separated machines
connected over the TCP/IP network. HAST works in Primary-Secondary
(Master-Backup, Master-Slave) configuration, which means that only one of the
cluster nodes can be active at any given time. Only Primary node is able to
handle I/O requests to HAST-managed devices. Currently HAST is limited to two
cluster nodes in total.
HAST operates on block level - it provides disk-like devices in /dev/hast/
directory for use by file systems and/or applications. Working on block level
makes it transparent for file systems and applications. There in no difference
between using HAST-provided device and raw disk, partition, etc. All of them
are just regular GEOM providers in FreeBSD.
For more information please consult hastd(8), hastctl(8) and hast.conf(5)
manual pages, as well as http://wiki.FreeBSD.org/HAST.
Sponsored by: FreeBSD Foundation
Sponsored by: OMCnet Internet Service GmbH
Sponsored by: TransIP BV
specify list of executables and/or rc scripts that should be executed
after firewall starts/stops.
Submitted by: Yuri Kurenkov <y dot kurenkov at init dot ru>
Reviewed by: rhodes, rc@
MFC after: 1 week
maximum file size limit. Default is UINT64_MAX when the option is
not specified. It was useless to set the limit to the total amount of
memory and swap in the system.
Use tmpfs_mem_info() rather than get_swpgtotal() in tmpfs_mount() to
check if there is enough memory available.
Remove now unused get_swpgtotal().
Reviewed by: Gleb Kurtsou
Approved by: trasz (mentor)
wlan(4) interfaces. vlan(4) interfaces are listed via a new 'vlans_<IF>'
variable. If a vlan interface is a number, then that number is treated as
the vlan tag for the interface and the interface will be named '<IF>.<tag>'.
Otherwise, the vlan tag must be provided via a vlan parameter in a
'create_args_<vlan>' variable.
While I'm here, fix a few nits in rc.conf(5) and mention create_args_<IF> in
the description of cloned_interfaces.
Reviewed by: brooks
MFC after: 2 weeks
re-add $ipv6_enable support for backward compatibility. From
UPDATING:
1. To use IPv6, simply define $ifconfig_IF_ipv6 like $ifconfig_IF
for IPv4. For aliases, $ifconfig_IF_aliasN should be used.
Note that both variables need the "inet6" keyword at the head.
Do not set $ipv6_network_interfaces manually if you do not
understand what you are doing. It is not needed in most cases.
$ipv6_ifconfig_IF and $ipv6_ifconfig_IF_aliasN still work, but
they are obsolete.
2. $ipv6_enable is obsolete. Use $ipv6_prefer and/or
"inet6 accept_rtadv" keyword in ifconfig(8) instead.
If you define $ipv6_enable=YES, it means $ipv6_prefer=YES and
all configured interfaces have "inet6 accept_rtadv" in the
$ifconfig_IF_ipv6. These are for backward compatibility.
3. A new variable $ipv6_prefer has been added. If NO, IPv6
functionality of interfaces with no corresponding
$ifconfig_IF_ipv6 is disabled by using "inet6 ifdisabled" flag,
and the default address selection policy of ip6addrctl(8)
is the IPv4-preferred one (see rc.d/ip6addrctl for more details).
Note that if you want to configure IPv6 functionality on the
disabled interfaces after boot, first you need to clear the flag by
using ifconfig(8) like:
ifconfig em0 inet6 -ifdisabled
If YES, the default address selection policy is set as
IPv6-preferred.
The default value of $ipv6_prefer is NO.
4. If your system need to receive Router Advertisement messages,
define "inet6 accept_rtadv" in $ifconfig_IF_ipv6. The rc(8)
scripts automatically invoke rtsol(8) when the interface becomes
UP. The Router Advertisement messages are used for SLAAC
(State-Less Address AutoConfiguration).
network_ipv6->rc.d/netif integration:
- $ipv6_enable is now obsolete. Instead, IPv6 is enabled by
default if the kernel supports it, and $ipv6_network_interfaces
is "none" by default. If you want to use IPv6, define
$ipv6_network_interfaces and $ifconfig_xxx_ipv6.
An interface which is in $network_interfaces and not in
$ipv6_network_interfaces will be marked as "inet6
-auto_linklocal ifdisabled" (see ifconfig(8)).
- $ipv6_ifconfig_xxx is renamed to ifconfig_xxx_ipv6 for
consistency with other address families. The old variables
still work but can be removed in the future. Note that
ipv6_ifconfig_xxx="..." should be replaced with
ifconfig_xxx_ipv6="inet6 ...".
- Receiving ICMPv6 Router Advertisement is not automatically
enabled even if there is no manual configuration of IPv6 in
rc.conf. If you want it, define
ifconfig_xxx_ipv6="inet6 ... accept_rtadv".
- The rc.d/ip6addrctl now chooses address selection policy based
on $ipv6_prefer, not $ipv6_enable. The default is
ipv6_prefer=NO.
- $router* and $ipv6_router* are replaced with $routed_* and
$route6d_* for consistency. The old variables still work but
can be removed in the future.
MFC after: 3 days
statically bind IPv4 <-> MAC address at boot time.
In order to use this, the administrator needs to configure the following
rc.conf(5) variable:
- static_arp_pairs: A list of names for static bind pairs, and,
- a series of static_arp_(name): the arguments that is being passed to
``arp -S'' operation.
Example:
static_arp_pairs="gw"
static_arp_gw="192.168.1.1 00:01:02:03:04:05"
See the rc.conf(5) manual page for more details.
Reviewed by: -rc@
MFC after: 2 weeks
using freebsd-update. This applies to using freebsd-update in "upgrade
mode" and normal freebsd-update on a security branch.
The backup kernel will be written to /boot/kernel.old, if the directory
does not exist, or the directory was created by freebsd-update in a
previous backup. Otherwise freebsd-update will generate a new directory
name for use by the backup. By default symbol files are not backed up
to save diskspace and avoid filling up the root partition.
This feature is fully configurable in the freebsd-update config file,
but defaults to enabled.
MFC after: 1 week (stable/7)
Reviewed by: cperciva
Approved by: re (kib)
