messages like this:
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (wd0): <ST506>
wd0: size unknown, using BIOS values: 615 cyl, 4 head, 17 sec, bytes/sec 512
npx0 at 0xf0-0xff irq 13 on motherboard
npx0: changing root device to wd0a
^^^^^^
The spurious 'npx0: ' pops up if you have a 386 with a 387 FPU.
briefly over it, and see some serious architectural issues in this stuff.
On the other hand, I doubt that we will have any solution to these issues
before 2.1, so we might as well leave this in.
Most of the stuff is bracketed by #ifdef's so it shouldn't matter too much
in the normal case.
Reviewed by: phk
Submitted by: HOSOKAWA, Tatsumi <hosokawa@mt.cs.keio.ac.jp>
Put in the much shorter and cleaner version for the calibrate_cycle_counter
for the Pentium that Bruce suggested. Tested here on my Pentium and
it works okay.
shifting. Also correct the original code as Garrett noticed it in mail.
Leave the mishandled code in to use it later if future versions of gcc
are correct. The code was part of the calibrate_cyclecounter routine to
get the speed of the pentium chip.
Remove bogus input operands for fnsave(), fnstcw() and fnstsw().
Change all fwait's to fnop's. This might help avoid hardware bugs.
Wait after fninit with an fnop. This should be safer now.
Fix some spelling and formatting errors.
Use natural sizes for control and status words (u_short, promotes to int).
Don't clobber the SWI_CLOCK_MASK bits in npx0_imask when using IRQ13.
Set the devconf state correctly (always busy, if configured). Improve
code for npx_registerdev() a little (gcc can't keep id->id_unit in a
register for some reason). Don't register a nonexistent npx device.
Print a useful message in npxattach() again (delete references to errors
and not the whole message). Don't print "387 emulator" if there is no
emulator in the kernel.
Use %p for pointers in error messages.
Don't clobber the FPU state when there is an FPU exception. Just clear
the exception flags (after saving the flags as before). This allows
debuggers and SIGFPE handlers to look at the full exception state.
SIGFPE handlers should normally return via longjmp(), which restores a
good FPU state (as before). Returning from a SIGFPE handler may leave
the FPU in the wrong state (as before).
Clear the busy latch _after_ clearing the exception flags so that there
is less chance of getting a bogus h/w interrupt for a control operation.
Clear the saved exception status word when the next FPU instruction is
excuted so that it doesn't stick around until the next exception.
Clear the busy latch after fnsave() in npxsave() in case it was set when
npxsave() was called.
Move definition of `stat_imask' to clock.c.
clock.c:
Rename `rtcmask' to `stat_imask' and export it. Rename `clkmask' to
`clk_imask' for consistency.
Only calculate TIMER_DIV(hz) once.
Merge debugging and "garbage" code to produce debugging code and format the
output better.
Make writertc() static inline and use it everywhere. Now all accesses to
the clock registers go through rtcin() and writertc().
Move rtc initialization to cpu_initclocks().
Merge enablertclock() with cpu_initclocks() and remove enablertclock().
The extra entry point was just a leftover from 1.1.5.
Keep track of interrupt nesting level. It is normally 0
for syscalls and traps, but is fudged to 1 for their exit
processing in case they metamorphose into an interrupt
handler.
i386/genassym.c;
Remove support for the obsolete pcb_iml and pcb_cmap2.
Add support for pcb_inl.
i386/swtch.s:
Fudge the interrupt nesting level across context switches and in
the idle loop so that the work for preemptive context switches
gets counted as interrupt time, the work for voluntary context
switches gets counted mostly as system time (the part when
curproc == 0 gets counted as interrupt time), and only truly idle
time gets counted as idle time.
Remove obsolete support (commented out and otherwise) for pcb_iml.
Load curpcb just before curproc instead of just after so that
curpcb is always valid if curproc is. A few more changes like
this may fix tracing through context switches.
Remove obsolete function swtch_to_inactive().
include/cpu.h:
Use the new interrupt nesting level variable to implement a
non-fake CLF_INTR() so that accounting for the interrupt state
works.
You can use top, iostat or (best) an up to date systat to see
interrupt overheads. I see the expected huge interrupt overheads
for ISA devices (on a 486DX/33, about 55% for an IDE drive
transferring 1250K/sec and the same for a WD8013EBT network card
transferring 1100K/sec). The huge interrupt overheads for serial
devices are unfortunately normally invisible.
include/pcb.h:
Remove the obsolete pcb_iml and pcb_cmap2. Replace them by
padding to preserve binary compatibility.
Use part of the new padding for pcb_inl.
isa/icu.s:
isa/vector.s:
Keep track of interrupt nesting level.
with the current default exception (un)mask. There should be no such
processes unless you change the mask. Someday the mask should be
changed to the IEEE default of everything masked. The npx state
gets saved so that it can be checked and this may have the side effect
of fixing a bug that was reported for 1.1.5. (npx exceptions may
sometimes leak across exits and clobber another process. I can't see
how this can happen.)
Get some missing/wrong declarations from headers now that the headers
have them.
doesn't have to calculate it every call.
Rename `timer0_prescale' to `timer0_prescaler_count' and maintain it
correctly. Previously we lost a few 8253 cycles for every "prescaled"
clock interrupt, and the lossage grows rapidly at 16 KHz. Now we
only lose a few cycles for every standard clock interrupt.
Rename `*_divisor' to `*_max_count'.
Do the calculation of TIMER_DIV(rate) only once instead of 3 times each
time the rate is changed.
Don't allow preposterously large interrupt rates. Bug fixes elsewhere
should allow the system to survive rates that saturate the system, however.
Clean up declarations.
Include <machine/clock.h> to check our own declarations.
Changed the fifth parameter to register_intr() from u_int mask into
u_int *maskptr in preparation for new features (shared interrupts and
removable devices, eg. for PCMCIA).
Changed the fifth parameter to register_intr() from u_int mask into
u_int *maskptr in preparation for new features (shared interrupts and
removable devices, eg. for PCMCIA).
and all SCSI devices (except that it's not done quite the way I want). New
information added includes:
- A text description of the device
- A ``state''---unknown, unconfigured, idle, or busy
- A generic parent device (with support in the m.i. code)
- An interrupt mask type field (which will hopefully go away) so that
. ``doconfig'' can be written
This requires a new version of the `lsdev' program as well (next commit).
drivers have a chance to change their IRQ before it is checked.
This was implemented in revision 1.21 and broken in revision 1.26.
Drivers that can change their IRQ should probably be configured
with "irq ?".
else has been probed. This feature could go away again, if we can curb the
problem another way.
if_ed.c, syscons.c: Set the above flag. ed# because it needs it, syscons
because it looks stupid to "detect" the display you have already filled up
with text :-)
bt742a.c: Check bt_cmd() return-val during probe, thus failing on adaptec's.
Also silenced various printf's during the probe.
isa.c: Probe devices with the above flag set before the rest. Reduce the
number of "conflict" messages per device to one.
***
Please test the GENERIC-kernel now, if nobody can make it fail, GENERICAH
and GENERICBT has a finite and short life-expectancy...
***
