lnc(4) on PC98 and i386. The ISA front-end supports the same non-PNP
network cards as lnc(4) did and additionally a couple of PNP ones.
Like lnc(4), the C-bus front-end of le(4) only supports C-NET(98)S
and is untested due to lack of such hardware, but given that's it's
based on the respective lnc(4) and not too different from the ISA
front-end it should be highly likely to work.
- Remove the descriptions of le(4), which where converted from lnc(4),
from sys/i386/conf/NOTES and sys/pc98/conf/NOTES as there's a common
one in sys/conf/NOTES.
entry to the PCI NICs section so it's in the same spot in all GENERIC
config files.
- Add a note to the description of pcn(4) informing that is has precedence
over le(4).
o Properly use rman(9) to manage resources. This eliminates the
need to puc-specific hacks to rman. It also allows devinfo(8)
to be used to find out the specific assignment of resources to
serial/parallel ports.
o Compress the PCI device "database" by optimizing for the common
case and to use a procedural interface to handle the exceptions.
The procedural interface also generalizes the need to setup the
hardware (program chipsets, program clock frequencies).
o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by
default and non-serdev devices are handled by the bus.
o Use the serdev I/F to collect interrupt status and to handle
interrupts across ports in priority order.
o Sync the PCI device configuration to include devices found in
NetBSD and not yet merged to FreeBSD.
o Add support for Quatech 2, 4 and 8 port UARTs.
o Add support for a couple dozen Timedia serial cards as found
in Linux.
to COMPAT_43TTY.
Add COMPAT_43TTY to NOTES and */conf/GENERIC
Compile tty_compat.c only under the new option.
Spit out
#warning "Old BSD tty API used, please upgrade."
if ioctl_compat.h gets #included from userland.
via the DEFAULTS kernel configs. This allows folks to turn it that option
off in the kernel configs if desired without having to hack the source.
This is especially useful since PUC_FASTINTR hangs the kernel boot on my
ultra60 which has two uart(4) devices hung off of a puc(4) device.
I did not enable PUC_FASTINTR by default on powerpc since powerpc does not
currently allow sharing of INTR_FAST with non-INTR_FAST like the other
archs.
IPI_STOP IPIs.
- Change the i386 and amd64 MD IPI code to send an NMI if STOP_NMI is
enabled if an attempt is made to send an IPI_STOP IPI. If the kernel
option is enabled, there is also a sysctl to change the behavior at
runtime (debug.stop_cpus_with_nmi which defaults to enabled). This
includes removing stop_cpus_nmi() and making ipi_nmi_selected() a
private function for i386 and amd64.
- Fix ipi_all(), ipi_all_but_self(), and ipi_self() on i386 and amd64 to
properly handle bitmapped IPIs as well as IPI_STOP IPIs when STOP_NMI is
enabled.
- Fix ipi_nmi_handler() to execute the restart function on the first CPU
that is restarted making use of atomic_readandclear() rather than
assuming that the BSP is always included in the set of restarted CPUs.
Also, the NMI handler didn't clear the function pointer meaning that
subsequent stop and restarts could execute the function again.
- Define a new macro HAVE_STOPPEDPCBS on i386 and amd64 to control the use
of stoppedpcbs[] and always enable it for i386 and amd64 instead of
being dependent on KDB_STOP_NMI. It works fine in both the NMI and
non-NMI cases.
originally wrote it for 4.x and hasn't really had the time to fully update
it to 5.x and later. Also, the author doesn't use the hardware anymore as
well. If someone does need this driver they can always resurrect it from
the Attic.
Requested by: Frank Mayhar frank at exit dot com
This kernel config briefly describes some of the major MAC policies
available on FreeBSD. The hope is that this will raise the awareness
about MAC and get more people interested.
Discussed with: scottl
as they are already default for I686_CPU for almost 3 years, and
CPU_DISABLE_SSE always disables it. On the other hand, CPU_ENABLE_SSE
does not work for I486_CPU and I586_CPU.
This commit has:
- Removed the option from conf/options.*
- Removed the option and comments from MD NOTES files
- Simplified the CPU_ENABLE_SSE ifdef's so they don't
deal with CPU_ENABLE_SSE from kernel configuration. (*)
For most users, this commit should be largely no-op. If you used to
place CPU_ENABLE_SSE into your kernel configuration for some reason,
it is time to remove it.
(*) The ifdef's of CPU_ENABLE_SSE are not removed at this point, since
we need to change it to !defined(CPU_DISABLE_SSE) && defined(I686_CPU),
not just !defined(CPU_DISABLE_SSE), if we really want to do so.
Discussed on: -arch
Approved by: re (scottl)
FreeBSD based on aue(4) it was picked by OpenBSD, then from OpenBSD ported
to NetBSD and finally NetBSD version merged with original one goes into
FreeBSD.
Obtained from: http://www.gank.org/freebsd/cdce/
NetBSD
OpenBSD
This is mentioned in the Handbook but it is not as obvious to new
users why bpf is needed compared to the other largely self-explanatory
items in GENERIC.
PR: conf/40855
MFC after: 1 week
from 4.x kernel config files. User's wishing to upgrade from 4.x to 6
will need to go through 5.x, or grab this script from there. These
scripts will remain in RELENG_5...
