The datasheets for these chips claim the maximum is 921,600, but testing
shows these two higher rates also work (but no rates above 921,600 other
than these two work; these represent dividing the base buad clock by 3 and 2
respectively).
As we do for many other laptops, put the headphone jack and speakers in
the same association by default so that the generic sound device
automatically switches between them.
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Summary:
In rS338751, the check to declare `timespec_get()` for C++17 and higher
was incorrectly done against a `cplusplus` define, while it should have
been `__cplusplus`.
Fix this by using `__cplusplus`, and also bump `__FreeBSD_version` so it
becomes possible to correctly check for `timespec_get()` in upstream
libc++ headers.
Reviewed by: brooks, emaste
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D22735
Partially revert r354741 and r354754 and go back to allocating a
fixed-size chunk of stack space for the auxiliary vector. Keep
sv_copyout_auxargs but change it to accept the address at the end of
the environment vector as an input stack address and no longer
allocate room on the stack. It is now called at the end of
copyout_strings after the argv and environment vectors have been
copied out.
This should fix a regression in r354754 that broke the stack alignment
for newer Linux amd64 binaries (and probably broke Linux arm64 as
well).
Reviewed by: kib
Tested on: amd64 (native, linux64 (only linux-base-c7), and i386)
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D22695
of the sensor hardware. Part of the polling process involves signalling
the chip then waiting 20 milliseconds. This was being done with DELAY(),
which is a pretty rude thing to do in a callout. Now a taskqueue_thread
task is scheduled to do the polling, and because sleeping is allowed in
the task context, pause_sbt() replaces DELAY() for the 20ms wait.
r354875 pushed VCBUS <-> ARMC translations to runtime determination, but
incorrectly mapped addresses for the BCM2836 -- SOC_BCM2835 and SOC_BCM2836
are actually mutually exclusive, so the BCM2836 config (GENERIC) would have
taken the latter path in the header and used 0x3f000000 as peripheral start.
Easily fixed -- split out the BCM2836 into its own memmap config and use
that instead if SOC_BCM2836 is included. With this, we get back to userland
again.
Reported by: Marek Zarychta <zarychtam@plan-b.pwste.edu.pl>
This change adds PowerPC64 support for minidumps on libkvm.
Address translation, page walk, and data retrieval were tested and seem to be
working correctly.
Reviewed by: jhibbits
Differential Revision: https://reviews.freebsd.org/D21555
This change enables the use of OpenFirmware Console (ofwcons), even when VGA is
available, allowing early kernel messages to be seen, that is important in case
of crashes before VGA console initialization.
This is specially useful in virtualized environments, where the user/developer
doesn't have full control of the virtualization engine (e.g. OpenStack).
The old behavior is preserved by default and, in order to use ofwcons, a few
tunables that have been introduced need to be set:
- hw.ofwfb.disable=1 - disable OFW FrameBuffer device
- machdep.ofw.mtx_spin=1 - change PPC OFW mutex to SPIN type, to match kernel
console's mutex type
- debug.quiesce_ofw=0 - don't call OFW quiesce, needed to keep ofwcons I/O
working
More details can be found at differential revision D20640.
Reviewed by: jhibbits
Differential Revision: https://reviews.freebsd.org/D20640
This change makes it possible to use OPAL console as a GDB debug port.
Similar to uart and uart_phyp debug ports, it has to be enabled by
setting the hw.uart.dbgport variable to the serial console node
of the device tree.
Reviewed by: jhibbits
Differential Revision: https://reviews.freebsd.org/D22649
Routing statistics requires somes symbols that are only loaded when not running
live. Load them only in that specific case
PR: 242423
Submitted by: olivier
MFC after: 3 days
to its successor in cases where examining a map entry requires a
helper like kvm_read_all. Use that method, with kvm_read_all, to fix
procstat_getfiles_kvm, which tries to find the successor now without
using such a helper. This addresses a problem introduced by r355491.
Reviewed by: markj (previous version)
Discussed with: kib
Differential Revision: https://reviews.freebsd.org/D22728
The current vnode layout is not smp-friendly by having frequently read data
avoidably sharing cachelines with very frequently modified fields. In
particular v_iflag inspected for VI_DOOMED can be found in the same line with
v_usecount. Instead make it available in the same cacheline as the v_op, v_data
and v_type which all get read all the time.
v_type is avoidably 4 bytes while the necessary data will easily fit in 1.
Shrinking it frees up 3 bytes, 2 of which get used here to introduce a new
flag field with a new value: VIRF_DOOMED.
Reviewed by: kib, jeff
Differential Revision: https://reviews.freebsd.org/D22715
1. replace hand-rolled macros for operation type with enum
2. unlock the vnode in vput itself, there is no need to branch on it. existence
of VPUTX_VPUT remains significant in that the inactive variant adds LK_NOWAIT
to locking request.
3. remove the useless v_usecount assertion. few lines above the checks if
v_usecount > 0 and leaves. should the value be negative, refcount would fail.
4. the CTR return vnode %p to the freelist is incorrect as vdrop may find the
vnode with holdcnt > 1. if the like should exist, it should be moved there
5. no need to error = 0 for everyone
Reviewed by: kib, jeff (previous version)
Differential Revision: https://reviews.freebsd.org/D22718
changed the sysctl format for the temperature from "I" to "IK", and
correspondingly changed the units from integer degrees C to decikelvin.
For access via sysctl(8) the output will be the same except that now
decimal fractions will be shown when available.
Previously the driver supported the DHT11 sensor. Now it supports
DHT11, DHT12, DHT21, DHT22, AM3201, AM3202.
All these chips are similar, differing primarily in supported temperature
and humidity ranges and accuracy (and, presumably, cost). There are two
basic data formats reported by the various chips, and it is possible to
figure out at runtime which format to use for decoding the data based on
the range of values in a single byte of the humidity measurement. (which
is detailed in a comment block, so I won't recapitulate it here).
functions to handle the sysctls, they all just access simple readonly
integer variables. There's no need to track the oids of the ones we add,
since the teardown is done by newbus code, not the driver itself.
Also remove the DDB code, because it just provides access to the same data
that the sysctls already provide.
At the end of a read cycle, set the gpio pin to INPUT rather than OUTPUT.
The state of the single-wire "bus" when idle should be high; setting the
pin to input allows the external pullup to pull the line high. Setting it
to output (and leaving it driving low) was leading a good read cycle followed
by one that would fail, and it just continued like that forever, effectively
reading the sensor once every 10 seconds instead of 5.
In the attach function, do an initial read from the device before registering
the sysctls for accessing the last-read values, to prevent reading spurious
values for the first 5 seconds after the driver attaches.
Do a callout_drain() in the detach function to prevent crashes after
unloading the module.
Summary:
There's no need to use the fallback fls() and flsl() libkern functions
when the PowerISA includes instructions that already do the bulk of the
work. Take advantage of this through the GCC builtins __builtin_clz()
and __builtin_clzl().
Reviewed by: luporl
Differential Revision: https://reviews.freebsd.org/D22340
Summary:
moea64_pte_sync_native() and moea64_pte_unset_native() don't need the
full PTE created, they only need to check that the PVO has a matching
PTE to the PTE in the page table. Don't waste time creating the full
PTE in this case.
Reviewed by: luporl
Differential Revision: https://reviews.freebsd.org/D22341
zones would never be freed. In the case of tmpfs this was not true. While
here test for the right bit to disable the keg related sysctls for zones
that don't have kegs.
Reported by: pho
Reviewed by: rlibby
Differential Revision: https://reviews.freebsd.org/D22655
A valid reference is all that is required. If we race with a deallocation
we will harmlessly misidentify the type of an already dead object.
Reviewed by: kib, markj
Differential Revision: https://reviews.freebsd.org/D22636
- Do not unnecessarily strdup().
- Check return value of getdiskinfo(), if it failed, bail out.
Reviewed by: imp
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D22729
embedded slabs but also is an opportunity to tidy up code and add
accessor inlines.
Reviewed by: markj, rlibby
Differential Revision: https://reviews.freebsd.org/D22609
When an NFSv4 server replies NFSERR_MINORVERSMISMATCH, it does not generate
a status result for the first operation in the compound. Without this
patch, this will result in a bogus EBADXDR error return.
Returning EBADXDR is relatively harmless, but a correct reply of
NFSERR_MINORVERSMISMATCH is needed by the pNFS client to select the correct
minor version to use for a File Layout DS now that there can be NFSv4.2
DS servers.
mount_nfs.c still needs to be fixed for this, although how the mount fails
is only useful to help sysadmins isolate why a mount fails.
Found during testing of the NFSv4.2 client and server.
MFC after: 2 weeks
This is a preliminary commit of NFSv4.2 definitions that will be used by
subsequent commits which adds NFSv4.2 support to the NFS client and server.
There will be a series of these preliminary commits that will prepare for
a major commit of the NFSv4.2 client/server changes currently found in
subversion under projects/nfsv42/sys.
