instead of trying to cache it.
Previously, we only trusted the state if we did not have a cached state.
However, once a state was cached, the _STA method was always ignored.
Specifically, once a power resource had been turned on once (e.g.
during resume), the driver assumed it was always on even if _STA said it
was off and never turned it back on. This prevented the power resource
from being turned back on if a laptop was resumed twice, for example.
To fix, just remove the cached state entirely and always use the results
of _STA. The loops already skip any resources where _STA fails.
Submitted by: trasz (initial patch to invoke _ON)
MFC after: 1 week
corresponding flag(s) in the new map entry. Previously, the caller was
responsible for setting them after vm_map_insert() returned.
Pass MAP_STACK_GROWS_DOWN to vm_map_insert() from vm_map_growstack() when
extending the stack in the downward direction.
Together these changes slightly simplify the caller's task when creating a
downward growing stack. In particular, the caller no longer needs to clip
the previous entry, because the new stack entry can't possibly coalesce
with the previous entry.
Reviewed by: kib
Sponsored by: EMC / Isilon Storage Division
From one side it allows to remove CTL_FLAG_TASK_PENDING flag, handling of
which significantly complicates fine-grained locking. From the other side
it reduces task management requests latency even below then that flag could.
As downside, it denies task management code to sleep, but that is not needed
any way now.
Discussed with: ken
This should allow to abort commands doing mostly disk I/O, such as VERIFY
or WRITE SAME. Before this change CTL_FLAG_ABORT was only checked around
data moves, which for these commands may not happen for a very long time.
MFC after: 2 weeks
SPC-4 recommends T10 vendor ID based LUN ID was created by concatenating
product name and serial number (and istgt follows that). But product name
is 16 bytes long by itself, so 16 bytes total length is clearly not enough
to fit both.
To keep compatibility with existing configurations, pad short device IDs
to old length of 16, same as before.
This change probably breaks CTL user-level ABI, so control tools should
be rebuilt after this change.
MFC after: 2 weeks
we're now back to the pre-r228483 level of default verbosity. This in
turn again typically allows for reading information that userland might
have printed on the screen before initiating a halt, but still permits
to debug potential device shutdown problems on system shutdown via
CAM_DEBUG etc.
Reviewed by: mav
MFC after: 3 days
Sponsored by: Bally Wulff Games & Entertainment GmbH
and prevents the request from deleting existing mappings in the
region, failing instead.
Reviewed by: alc
Discussed with: jhb
Tested by: markj, pho (previous version, as part of the bigger patch)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Posix strptime() requires support for %t and %n, which were added
to the illumos port. Curiously we were skipping white spaces by
default in most other cases making %t meaningless.
We now skip spaces in the case of the %e specifier as strftime(3)
explicitly adds a space for the single digit case.
Reference:
http://pubs.opengroup.org/onlinepubs/009695399/functions/strptime.html
Obtained from: Illumos (Rev. a11c1571b6942161b0186d0588609448066892c2)
MFC after: 3 weeks
when looking for configured addresses.
This change is based upon the code from the submitter, and made
following changes:
- Exclude addresses assigned on interfaces which are down, like NetBSD
does.
- Exclude addresses assigned on interfaces which are ifdisabled.
PR: 190824
Submitted by: Justin McOmie
MFC after: 1 week
for any outstanding commands to be properly aborted by CTL.
Without it, in some cases (such as files backing the LUNs
stored on failing disk drives), terminating a busy session
would result in panic.
Reviewed by: mav@ (earlier version)
Sponsored by: The FreeBSD Foundation
Fix the gate in xen_pv_lapic_ipi_vectored to prevent access to element
at position nitems(xen_ipis).
Sponsored by: Citrix Systems R&D
Coverity ID: 1223203
Approved by: gibbs
- Don't compare the DMA map to NULL to determine if bus_dmamap_unload()
should be called when releasing a static allocation. Instead, compare
the bus address against 0.
- Don't assume that the DMA map for static allocations is NULL. Instead,
save the value set by bus_dmamem_alloc() so it can later be passed to
bus_dmamem_free(). Also, add missing calls to bus_dmamap_unload() in
these cases before freeing the buffer.
- Use the bus address from the bus_dma callback instead of calling
vtophys() on the address allocated by bus_dmamem_alloc().
Reviewed by: kan
- Add missing calls to bus_dmamap_unload() in et(4).
- Check the bus address against 0 to decide when to call
bus_dmamap_unload() instead of comparing the bus_dma map against NULL.
- Check the virtual address against NULL to decide when to call
bus_dmamem_free() instead of comparing the bus_dma map against NULL.
- Don't clear bus_dma map pointers to NULL for static allocations.
Instead, treat the value as completely opaque.
- Pass the correct virtual address to bus_dmamem_free() in wpi(4) instead
of trying to free a pointer to the virtual address.
Reviewed by: yongari
This consists of the unique glyphs from the following font files in
/usr/share/syscons/fonts:
iso*.fnt ISO-8859-1 West European
iso02*.fnt ISO-8859-2 Central European
iso04*.fnt ISO-8859-4 Baltic
iso05*.fnt ISO-8859-5 Cyrillic
iso07*.fnt ISO-8859-7 Greek
iso08*.fnt ISO-8859-8 Hebrew
iso09*.fnt ISO-8859-9 Turkish
iso15*.fnt ISO-8859-15 West European
Sponsored by: The FreeBSD Foundation
