Commit Graph

22 Commits

Author SHA1 Message Date
Alexander Motin
301c88be98 MFp4:
After last running command completed, give commands in timeout state
second time.
2010-02-14 12:27:49 +00:00
Alexander Motin
2622a559a7 Use new helper functions to set PCIe max read request size. 2010-02-05 17:20:48 +00:00
Alexander Motin
4cca153030 - Give ATA/SATA SIMs info about ATAPI packet size, supported by device.
- Make ATA XPT to reject longer SCSI CDBs then supported by device, or
any SCSI CDBs, if device doesn't support ATAPI.
2010-02-02 11:09:28 +00:00
Alexander Motin
ed70cffd35 Reset port on disconnect event, to abort any running requests. 2010-01-29 12:47:04 +00:00
Alexander Motin
83c5d981ac MFp4: Large set of CAM inprovements.
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
2010-01-28 08:41:30 +00:00
Alexander Motin
723bd8c6b5 Usually these controllers are able to automatically decode command code to
get required command protocol. But they have no idea about new commands,
such as DATA SET MANAGEMENT (TRIM). As soon as this info any way provided
by CAM, give controller specific instructions.
2009-12-29 21:49:11 +00:00
Alexander Motin
1535d59d7c Increase Max Read Request Size for PCIe chips from 512 to 1024 bytes.
It gives those beasts additional 10% of write bandwidth.
2009-12-09 13:10:10 +00:00
Alexander Motin
3005368137 Explicitly acknowledge MSI completion, as required by SiI3124 datasheet.
It makes MSI working there. Later (and cheaper) PCIe chips (3132/3531)
still randomly crashing system in few seconds of high MSI rates, generating
something inaporopriate, like NMI or "Fatal trap 30".
2009-12-07 18:37:50 +00:00
Alexander Motin
d095fa045c SiI3124 has no SNotification register. Handle Asynchronous Notifications
there without it as good as possible.
2009-12-07 16:10:48 +00:00
Alexander Motin
b447e682d6 MFp4:
Improve ATA mode/SATA revision control.
2009-11-26 08:49:46 +00:00
Alexander Motin
c8039fc667 MFp4:
- Extend XPT-SIM transfer settings control API. Now it allows to report to
SATA SIM number of tags supported by each device, implement ATA mode and
SATA revision negotiation for both SATA and PATA SIMs.
- Make ahci(4) and siis(4) to use submitted maximum tag number, when
scheduling requests. It allows to support NCQ on devices with lower tags
count then controller supports.
- Make PMP driver to report attached devices connection speeds.
- Implement ATA mode negotiation between user settings, device and
controller capabilities.
2009-11-24 12:47:58 +00:00
Alexander Motin
5319fb62a8 Do not require payload data to be aligned. It is not mentioned in datasheet
and works fine in practice.
2009-11-16 20:54:47 +00:00
Alexander Motin
30a4094f86 MFp4:
- Move tagged queueing control from ADA to ATA XPT. It allows to control
  device command queue length correctly. First step to support < 32 tags.
- Limit queue for non-tagged devices by 2 slots for ahci(4) and siis(4).
- Implement quirk matching for ATA devices.
- Move xpt_schedule_dev_sendq() from header to source file.
- Move delayed queue shrinking to the more expected place - element freeing.
- Remove some SCSIsms in ATA.
2009-11-11 11:10:36 +00:00
Alexander Motin
03a6387ec3 MFp4:
Organize device IDs and add some more of them.
2009-11-10 09:46:52 +00:00
Alexander Motin
c82b245af9 Do not unarm callout on request completion and change slot selection
algorithm as done in ahci(4). This saves some CPU time on high request
rates.
2009-11-04 15:10:46 +00:00
Alexander Motin
6f9a51c735 MFp4:
- Rework timeout handling, to make it more graceful for devices sharing
controller port (with PMP). Wait for other commands completion/timeout
before initiating recovery.
- Handle timeouts and fatal errors with port hard-reset. The rest of
recovery will be done by XPT on receiving async event. More gracefull
per-device soft-reset recovery can be implemented later.
2009-11-03 12:03:13 +00:00
Alexander Motin
27acd6ea1f Reimplement device reset sequence in more controller-specific way. 2009-10-23 21:33:26 +00:00
Alexander Motin
8e7cccb3bd MFp4:
Report real max_target = 15. SIM doesn't need to know that target 15 is PMP.
It is XPT business.
2009-10-21 13:00:01 +00:00
Alexander Motin
e06db1922d MFp4:
Freeze device queue on error to permit periph driver to do proper recovery.
2009-10-21 12:47:39 +00:00
Alexander Motin
660d482a4e On command timeout handle frozen command first, to not run it inside
XXX_end_transaction().

Submitted by:	avg
2009-10-07 15:40:04 +00:00
Alexander Motin
35713642d9 MFp4:
- Add SNTF support.
 - Do not report meaningless transport/protocol versions.
2009-08-30 15:06:03 +00:00
Alexander Motin
67b87e4429 Add siis CAM driver for SiliconImage SiI3124/3132/3531 SATA2 controllers.
Driver supports Serial ATA and ATAPI devices, Port Multipliers
(including FIS-based switching), hardware command queues (31 command
per port) and Native Command Queuing. This is probably the second on
popularity, after AHCI, type of SATA2 controllers, that benefits from
using CAM, because of hardware command queuing support.

Approved by:    re (kib)
2009-07-21 12:32:46 +00:00