- Added a workaround for NC-SI management firmware that would allow
frames to be accepted while the driver is resetting the hardware.
This failure is generally observed when broadcast frames are received
during driver load and will generate "Unable to write CTX memory"
errors.
- Small changes to driver flags display.
PR: kern/135836, kern/140684
Add TSO support on VLANs. Intentionally separated IFCAP_VLAN_HWTSO
from IFCAP_VLAN_HWTAGGING. I think some hardwares may be able to
TSO over VLAN without VLAN hardware tagging.
Driver changes and userland support will follow.
r203358:
PCI express device status register has W1C feature. Writing 0 has
no effect. Make sure to clear error bits by writing 1. [1]
While I'm here use predefined value instead of hardcodig magic
vlaue.
Submitted by: msaitoh at NetBSD [1]
r203716:
Move device specific flag configuration to attach routine.
The softc obtained in device probe wouldn't be the same one used in
device attach. Drivers should not assume any values stored in softc
structure in probe routine will be available for its attach routine.
r202821:
Fix a long standing ASF heartbeat sending bug. The initial
implementation of heartbeat interval was 2 but there was typo which
caused the heartbeat is sent approximately every 5 seconds. This
caused unintended controller reset by firmware because firmware
thought OS was crashed.
Submitted by: Floris Bos < info <> je-eigen-domein dot nl >
Tested by: Andrzej Tobola < ato <> iem dot pw dot edu dot pl >
r202822:
Use new handshake command for BCM5750 or new controllers.
Add support for a few more Sony-specific ACPI features (default display
brightness, wired LAN power and bass gain), and update the description of
one previously unknown feature (display contrast). While here, expand on
a comment and remove two defines left over from an old version of the code.
Also update man page to document the above changes, and correct grammar.
PR: kern/127581
When growing a UFS1 filesystem, we need to initialise all inodes in any new
cylinder groups that are created. When the filesystem is first created,
newfs always initialises the first two blocks of inodes, and then in the
UFS1 case will also initialise the remaining inode blocks. The changes in
growfs.c 1.23 broke the initialisation of all inodes, seemingly based on
this implementation detail in newfs(8). The result was that instead of
initialising all inodes, we would actually end up initialising all but the
first two blocks of inodes. If the filesystem was grown into empty
(all-zeros) space then the resulting filesystem was fine, however when
grown onto non-zeroed space the filesystem produced would appear to have
massive corruption on the first fsck after growing.
A test case for this problem can be found in the PR audit trail.
Fix this by once again initialising all inodes in the UFS1 case.
PR: bin/115174
Submitted by: "Nate Eldredge" <nge cs.hmc.edu>
Reviewed by: mjacob
The -newerXB option was being interpreted the same as the -newerXm option
as a check for F_TIME2_B was missing. Fix this.
PR: bin/138245
Submitted by: "David E. Cross" <crossd cs.rpi.edu>
Make it more clear in the docs that -a is not compatible with -iFU,
and enforce this in the code. Apparently a lot of users mistakenly
combine -a with these flags and are then mystified that no changes
were made.
While I'm here, fix a trailing space in mergemaster.8
Fix ARM cache handling yet more.
1) vm_machdep.c: remove the dangling allocations so they do not
un-necessarily turn off the cache upon consecutive access.
2) busdma_machdep.c: remove the same amount than shadow mapped.
Reported by: Maks Verver
Submitted by: Mark Tinguely
Reviewed by: Grzegorz Bernacki
According to the Linux sungem driver, in case of Apple (K2) GMACs
GEM_MIF_CONFIG_MDI0 cannot be trusted when the firmware has powered
down the chip so the internal transceiver has to be hardcoded. This
is also in line with the AppleGMACEthernet driver, which just doesn't
distinguish between internal/external transceiver and MDIO/MDI1
respectively in the first place. Tested by: Andreas Tobler
- The OPSZ macro actually only does the right thing for int32 and int64
operands but not for double and extended double ones. Instead of trying
to fix the macro just nuke it and unroll the loops in the correct way
though as extended double operands turn out to be the only special case.
- For FxTO{s,d,q} the source operand is int64 so rs2 has to be re-decoded
after setting type accordingly as it's generally decoded using the low
2 bits as the type, which are 0 for these three instructions.
- Similarly, in case of F{s,d,q}TOx the target is int64 so rd has to be
re-decoded using not only the operand mask appropriate for int64 but
also the correct register number encoding.
- Use const where appropriate.
- Wrap long lines.
Submitted by: Peter Jeremy (partly)
When a kinfo_proc is filled, first fill_kinfo_proc_only() fills in
ki_runtime using p->p_rux.rux_runtime (all cpu time used by the process
including terminated threads). If information for a specific thread is
requested, fill_kinfo_thread() then overwrites this with the thread's
td->td_runtime (good). If not, fill_kinfo_aggregate() overwrote it with
the sum of all threads' td->td_runtime which does not include terminated
threads.
This affects ps(1)'s TIME field, not its %CPU field nor anything in
top(1).
In _gettemp(), check that the length of the path doesn't exceed
MAXPATHLEN. Otherwise the path name (or part of it) may not fit to
carrybuf causing a buffer overflow.
PR: bin/140228
Traditionally, grdc would obtain time through time(3) which in turn gets
only the second part of clock (CLOCK_SECOND), and sleep for 1 second after
each screen refresh.
This approach would have two problems. First, we are not guaranteed to
be waken up at the beginning of a whole second, which will typically
exhibit as a "lag" on second number. Second, because we sleep for whole
second, and the refresh process would take some time, the error would
accumulate from time to time, making the lag variable.
Make grdc(6) to use time(3) to get time only at the beginning, and sample
time in CLOCK_REALTIME_FAST granularity after refreshing, and use the
nanosecond part to caculate how much time we want to sleep.
PR: bin/120813
Fix for the Intel WiFi Link 1000. The EEPROM image is in the OTPROM block
before the last block, not in the last block itself.
Approved by: rpaulo (mentor)
Obtained from: OpenBSD
Change the way shutdown is handled for log file.
pmc_flush_logfile is now non-blocking and just ask the kernel
to shutdown the file. From that point, no more data is
accepted by the log thread and when the last buffer is flushed
the file is closed.
This will remove a deadlock between pmcstat asking for
flush while it cannot flush the pipe itself.
Change the way shutdown is handled for log file.
pmc_flush_logfile is now non-blocking and just ask the kernel
to shutdown the file. From that point, no more data is
accepted by the log thread and when the last buffer is flushed
the file is closed.
This will remove a deadlock between pmcstat asking for
flush while it cannot flush the pipe itself.
Remove programming LED register and enable 25MHz TX clock for
88E1149 PHY. This will fix intermittent watchdog timeouts as well
as very slow network performance on 88E8072 Yukon Extreme.
PR: kern/144148
Sync acpi_video(4) with HEAD.
r197438:
Uninline an instance of STAILQ_FOREACH_SAFE().
r203810:
Implement LCD brightness control notify handler.
r203813:
Make sanity check slightly more useful and tweak an error message.
r203935:
Add support for `cycle' and `zero' events for LCD brightness control.
r203936:
Rename some macros to clarify their intentions and fix style nits.
The correct value of DEL is 0x7f, not 0xff. This is purely a documentation
issue - od(1) and hexdump(1) behave as expected.
PR: docs/143869
Submitted by: gcooper
Print the contents of the miscellaneous (MISC) register to the console if
it is valid along with the other register values when a machine check is
encountered.
Use reference counting instead of locking to secure an address while
that address is being used to generate temporary IPv6 address. This
approach is sufficient and avoids recursive locking.
- Adjust beginning / end of DST in Bangladesh (minimal impact)
- Fiji ends DST one month earlier to last Sunday of March
- Samoa changes
- Chile extends DST until 3 April this year.
Several changes to fix livelock under high load, introduced by r203489:
- change the way in which command queue overflow is handled;
- do not expose to CAM two command slots, used for driver's internal purposes;
- allow driver to use up to 1024 command slots, instead of 256 before.
