on temporary nameserver failure. This is necessary to get
getipnodebyname(3) to correctly return h_errno=TRY_AGAIN instead
of HOST_NOT_FOUND.
Reviewed by: green, thomas
MFC after: 1 week
For now, preserve the gif_called functionality to limit the nesting
level because uncontrolled nesting can easily cause the kernel stack
exhaustion. Rumors are it should be shot to allow people to easily
shoot themselves in the foot, but I have ran out of cartridges. ;)
(when new natd is started before old natd died) and allows to manage natd
without touching ipfw.
natd should probably be killed with SIGKILL when stopping natd.
- Use sendmail_foo variables after load_rc_config so that they actually work.
- Utilize sendmail_procname.
- Check sendmail_submit_enable instead of sendmail_enable when dealing
with mail submission MTA.
case we should wait for the resetdone handler to be called before
returning.
- When providing resources via ndis_query_resources(), uses the
computed rsclen when using bcopy() to copy out the resource data
rather than the caller-supplied buffer length.
- Avoid using ndis_reset_nic() in if_ndis.c unless we really need
to reset the NIC because of a problem.
- Allow interrupts to be fielded during ndis_attach(), at least
as far as allowing ndis_isr() and ndis_intrhand() to run.
- Use ndis_80211_rates_ex when probing for supported rates. Technically,
this isn't supposed to work since, although Microsoft added the extended
rate structure with the NDIS 5.1 update, the spec still says that
the OID_802_11_SUPPORTED_RATES OID uses ndis_80211_rates. In spite of
this, it appears some drivers use it anyway.
- When adding in our guessed rates, check to see if they already exist
so that we avoid any duplicates.
- Add a printf() to ndis_open_file() that alerts the user when a
driver attempts to open a file under /compat/ndis.
With these changes, I can get the driver for the SMC 2802W 54g PCI
card to load and run. This board uses a Prism54G chip. Note that in
order for this driver to work, you must place the supplied smc2802w.arm
firmware image under /compat/ndis. (The firmware is not resident on
the device.)
Note that this should also allow the 3Com 3CRWE154G72 card to work
as well; as far as I can tell, these cards also use a Prism54G chip.
without the (defunct) isa compatibility shims. The new-bus-specific
parts are very similar to the ones for the pci probe and attach.
This was held up too long waiting for a repo copy to src/sys/dev/cy,
so I decided to fix the files in their old place. This gives easier
to read and merge diffs anyway.
The "count" line in src/sys/conf/files won't be changed until after
the repo copy, so old kernel configs that specify a count need not be
(and must not be) changed until then. The count is just ignored in
the driver. One unfinished detail is dynamic allocation of arrays
with <count> and (<count> * 32) entries, and iteration over the arrays.
This is now kludged with a fixed count of 10 (up to 10 cards with up
to 32 ports each).
Prodded by: imp
Submitted by: mostly by imp
Approved by: imp
common attach function so that the lock gets initialized in all cases.
This fixes breakage of the initialization of the lock in the pci case
in rev.1.135 (between the releases of 5.1 and 5.2). The lock is only
used in the SMP case, so this bug was not always fatal.
vm_mmap_vnode function, where we can safely check for a special /dev/zero
case. Rev. 1.180 has reordered checks and introduced a regression.
Submitted by: alc
Was broken by: kan
and used by uart(4) for the channel conflicted with the port offset for
the Z8530. The Z8530 has the channels reversed (i.e. channel B is at
offset 0 and channel A is at offset 4). Assign the port offsets in the
right order so that uart(4) will properly attach to the channels.
Submitted by: Marius Strobl <marius@alchemy.franken.de>
It was fixed by moving problemetic checks, as well as checks that
doesn't need locking before locks are acquired.
Submitted by: Ryan Sommers <ryans@gamersimpact.com>
In co-operation with: cperciva, maxim, mlaier, sam
Tested by: submitter (previous patch), me (current patch)
Reviewed by: cperciva, mlaier (previous patch), sam (current patch)
Approved by: sam
Dedicated to: enough!
