Commit Graph

19 Commits

Author SHA1 Message Date
Marius Strobl
26280d88d7 - Introduce an ofw_bus kobj-interface for retrieving the OFW node and a
subset ("compatible", "device_type", "model" and "name") of the standard
  properties in drivers for devices on Open Firmware supported busses. The
  standard properties "reg", "interrupts" und "address" are not covered by
  this interface because they are only of interest in the respective bridge
  code. There's a remaining standard property "status" which is unclear how
  to support properly but which also isn't used in FreeBSD at present.
  This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
  ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
  vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
  This in turn allows to simplify and remove code-duplication in drivers for
  devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
  drivers for their children to use the ofw_bus kobj-interface. The IVAR-
  interfaces of the Central, EBus and FHC are entirely replaced by this. The
  PCI bus driver used its own kobj-interface and now also uses the ofw_bus
  one. The IVARs special to the SBus, e.g. for retrieving the burst size,
  remain.
  Beware: this causes an ABI-breakage for modules of drivers which used the
  IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
  recompiled.
  The style-inconsistencies introduced in some of the bus drivers will be
  fixed by tmm@ in a generic clean-up of the respective drivers later (he
  requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
  use the ofw_bus kobj-interface. This invloves removing the IVARs related
  to the "reg" property which were unused and a leftover from the NetBSD
  origini of the code. There's no ABI-breakage caused by this because none
  of these driver are currently built as modules.
  There are other powerpc bus drivers which can be converted to the ofw_bus
  kobj-interface, e.g. the PCI bus driver, which should be done together
  with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
  advantage of the ofw_bus kobj-interface and simplify them a bit.

Reviewed by:	grehan, tmm
Approved by:	re (scottl)
Discussed with:	tmm
Tested with:	Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
2004-08-12 17:41:33 +00:00
Warner Losh
48375ebec9 These don't need RMAN_RESOURCE_VISIBLE now that rman is visible 2004-07-03 20:56:16 +00:00
Marius Strobl
4eae91a8f7 These need __RMAN_RESOURCE_VISIBLE, too. 2004-06-30 23:21:07 +00:00
Poul-Henning Kamp
fd360128ff Add missing <sys/module.h> instances which were shadowed by the nested
include in <sys/kernel.h>
2004-06-03 05:58:30 +00:00
Marius Strobl
66a79ac95d - Remove the old sparc64 OFW PCI code (as opposed to the former
"options OFW_NEWPCI").
  This is a bit overdue, the new sparc64 OFW PCI code which is
  meant to replace the old one is in place for 10 months and
  enabled by default in GENERIC for 8 months. FreeBSD 5.2 and
  5.2.1 also shipped with the new code enabled by default.
- Some minor clean-up, e.g. remove functions that encapsulated
  the #ifdefs for OFW_NEWPCI, remove unused resp. no longer
  required includes, etc.

Approved by:	tmm, no objections on freebsd-sparc64
2004-05-08 13:53:47 +00:00
Thomas Moestl
34d32da2fb Remove inclusion of opt_ebus.h. 2004-04-30 19:19:55 +00:00
Thomas Moestl
e6597c747f Fix the EBus driver to work with the new PCI code. Unlike other PCI
bridges, the EBus bridge has resource ranges it claims exclusively to
map its children into in its BARs. Hence, we need to allocate these
completely and manage them for the children, instead of just passing
allocations through to the PCI layer as we did before.

While being there, split ebus_probe(), which did also contain code
normally belonging into the attach method, into ebus_probe() and
ebus_attach(), and perform some minor cleanups.
2004-04-28 13:06:46 +00:00
Thomas Moestl
38c174739c The compatibility specification property is named "compatible", not
"compat".

Spotted by:	Marius Strobl <marius@alchemy.franken.de>
2004-03-27 22:39:47 +00:00
Warner Losh
3d11ce04c6 s=include <ofw/=include <dev/ofw/= to reflect removal of -I$S/dev 2003-08-23 00:11:16 +00:00
Warner Losh
d2c5276d96 Prefer new location of pci include files (which have only been in the
tree for two or more years now), except in a few places where there's
code to be compatible with older versions of FreeBSD.
2003-08-22 07:39:05 +00:00
Thomas Moestl
1d80cb1b37 Add the new sparc64 OFW PCI framework, conditional on options OFW_NEWPCI
for now. It introduces a OFW PCI bus driver and a generic OFW PCI-PCI
bridge driver. By utilizing these, the PCI handling is much more elegant
now.

The advantages of the new approach are:
- Device enumeration should hopefully be more like on Solaris now,
  so unit numbers should match what's printed on the box more
  closely.
- Real interrupt routing is implemented now, so cardbus bridges
  etc. have at least a chance to work.
- The quirk tables are gone and have been replaced by (hopefully
  sufficient) heuristics.
- Much cleaner code.

There was also a report that previously bogus interrupt assignments
are fixed now, which can be attributed to the new heuristics.

A pitfall, and the reason why this is not the default yet, is that
it changes device enumeration, as mentioned above, which can make
it necessary to change the system configuration if more than one
unit of a device type is present (on a system with two hme cars,
for example, it is possible that hme0 becomes hme1 and vice versa
after enabling the option). Systems with multiple disk controllers
may need to be booted into single user (and require manual specification
of the root file system on boot) to adjust the fstab.
Nevertheless, I would like to encourage users to use this option,
so that it can be made the default soon.

In detail, the changes are:
- Introduce an OFW PCI bus driver; it inherits most methods from the
  generic PCI bus driver, but uses the firmware for enumeration,
  performs additional initialization for devices and firmware-specific
  interrupt routing. It also implements an OFW-specific method to allow
  child devices to get their firmware nodes.
- Introduce an OFW PCI-PCI bridge driver; again, it inherits most
  of the generic PCI-PCI bridge driver; it has it's own method for
  interrupt routing, as well as some sparc64-specific methods (one to
  get the node again, and one to adjust the bridge bus range, since
  we need to reenumerate all PCI buses).
- Convert the apb driver to the new way of handling things.
- Provide a common framework for OFW bridge drivers, used be the two
  drivers above.
- Provide a small common framework for interrupt routing (for all
  bridge types).
- Convert the psycho driver to the new framework; this gets rid of a
  bunch of old kludges in pci_read_config(), and the whole
  preinitialization  (ofw_pci_init()).
- Convert the ISA MD part and the EBus driver to the new way
  interrupts and nodes are handled.
- Introduce types for firmware interrupt properties.
- Rename the old sparcbus_if to ofw_pci_if by repo copy (it is only
  required for PCI), and move it to a more correct location (new
  support methodsx were also added, and an old one was deprecated).
- Fix a bunch of minor bugs, perform some cleanups.

In some cases, I introduced some minor code duplication to keep the
new code clean, in hopes that the old code will be unifdef'ed soon.

Reviewed in part by:	imp
Tested by:	jake, Marius Strobl <marius@alchemy.franken.de>,
		Sergey Mokryshev <mokr@mokr.net>,
		Chris Jackman <cjackNOSPAM@klatsch.org>
Info on u30 firmware provided by:	kris
2003-07-01 14:52:47 +00:00
Thomas Moestl
c944338750 Fix interrupt assignment for non-builtin PCI devices on e450s.
This machine uses a non-standard scheme to specify the interrupts to
be assigned for devices in PCI slots; instead of giving the INO
or full interrupt number (which is done for the other devices in this
box), the firmware interrupt properties contain intpin numbers, which
have to be swizzled as usual on PCI-PCI bridges; however, the PCI host
bridge nodes have no interrupt map, so we need to guess the
correct INO by slot number of the device or the closest PCI-PCI
bridge leading to it, and the intpin.

To do this, this fix makes the following changes:
- Add a newbus method for sparc64 PCI host bridges to guess
  the INO, and glue code in ofw_pci_orb_callback() to invoke it based
  on a new quirk entry. The guessing is only done for interrupt numbers
  too low to contain any IGN found on e450s.
- Create another new quirk entry was created to prevent mapping of EBus
  interrupts  at PCI level; the e450 has full INOs in the interrupt
  properties of EBus devices, so trying to remap them could cause
  problems.
- Set both quirk entries for e450s; remove the no-swizzle entry.
- Determine the psycho half (bus A or B) a driver instance manages
  in psycho_attach()
- Implement the new guessing method for psycho, using the slot number,
  psycho half and property value (intpin).

Thanks go to the testers, especially Brian Denehy, who tested many kernels
for me until I had found the right workaround.

Tested by:	Brian Denehy <B.Denehy@90east.com>, jake, fenner,
		Marius Strobl <marius@alchemy.franken.de>,
		Marian Dobre <mari@onix.ro>
Approved by:	re (scottl)
2003-05-30 20:48:05 +00:00
Warner Losh
a163d034fa Back out M_* changes, per decision of the TRB.
Approved by: trb
2003-02-19 05:47:46 +00:00
Alfred Perlstein
44956c9863 Remove M_TRYWAIT/M_WAITOK/M_WAIT. Callers should use 0.
Merge M_NOWAIT/M_DONTWAIT into a single flag M_NOWAIT.
2003-01-21 08:56:16 +00:00
Thomas Moestl
8c8a1169df Add two new workaround for firmware anomalies:
1. At least some Netra t1 models have PCI buses with no associated
   interrupt map, but obviously expect the PCI swizzle to be done with
   the interrupt number from the higher level as intpin. In this case,
   the mapping also needs to continue at parent bus nodes.
   To handle that, add a quirk table based on the "name" property of
   the root node to avoid breaking other boxen. This property is now
   retrieved and printed at boot.
2. On SPARCengine Ultra AX machines, interrupt numbers are not mapped
   at all, and full interrupt numbers (not just INOs) are given in
   the interrupt properties. This is more or less cosmetical; the
   PCI interrupt numbers would be wrong, but the psycho resource
   allocation method would pass the right numbers on anyway.

Tested by:	mux (1), Maxim Mazurok <maxim@km.ua> (2)
2002-11-07 16:07:46 +00:00
Thomas Moestl
464ae30ee6 Make the OpenFirmware interrupt mapping code more generic, to reduce
the bus-dependent code and to be able to support more systems. The core
of the new code is mostly obtained from NetBSD.
Kluge the interrupt routing methods of the psycho and apb drivers so
that an intline of 0 can be handled for now; real routing is still not
possible (all intline registers are preinitialized instead); this will
require a sparc64-specific adaption of the driver for generic PCI-PCI
bridges with a custom routing method to work right.
2002-03-24 02:11:06 +00:00
Thomas Moestl
d4f1dcab55 Set the interrupt map type accordingly if we need to fall back to using
the PCI bus interrupt map.
2002-03-09 22:02:02 +00:00
Thomas Moestl
c51aa38906 Minor bug fixes (add a missing break, correct the resource ranges, remove
a memory leak).
2002-02-13 15:35:22 +00:00
Thomas Moestl
94542806de Add EBus support code, ported from NetBSD. 2001-11-09 20:23:38 +00:00