This abstracts out all the differences I could see between the netbsd
sparc64 and macppc zs drivers. In particular the offsets of the csr and
data registers are different, so we use a separate bus handle for each and
use bus_space_subregion to add the bus specific offsets.
Requested by: benno
as separate 16-bit entities. Some of the ring control blocks are
in NIC memory, so they must be referenced using 32-bit accesses.
Smaller accesses have been observed to fail under some conditions.
This caused the rings to be set up wrong, leading to writes by the
card outside of the intended bounds of the rings. This problem was
diagnosed by Michael Barthelow. Don Bowman submitted a patch which
fixed the problem using a slightly different approach.
Reference ring control blocks in NIC memory using a pointer to
volatile.
Parenthesize the BGE_HOSTADDR macro definition properly.
MFC after: 3 days
from the hardware descriptors to avoid the overhead of having a DMA
map for each of them. Bump the number of hardware descriptors to 128,
and use half as many software descriptors for now.
Some minor cleanups.
- remove DPRINTF(), there is a CTR*() for any of them, and KTR is
far more useful to debug this driver.
- some cleanups; remove some unused code and definitions.
o create a separate tag for each object allocated with bus_dmamem_alloc so
the tag's maxsize is setup appropriately; this reduces memory allocation
for the queue descriptors from 16M to what it should be and also fixes
memory allocation for public key operands
o release bus dma resources on detach so module usage doesn't leak
o remove public key op disable now that bus dma memory allocation is fixed
o collect attach error handling in one place
Sponsored by: Vernier Networks
- 'spec' and 'ver' are attributes of a unit rather than a node.
- Report Phy and Link info separatelly.
- Reorder intialization step in fwohci_reset().
- Fix some bogosity with mixing unit numbers and channels, which would only
work for one instance of the device.
- Use a simpler scheme for input and output queueing.
- Use db_alt_break.
- Separate fc->dev (i.e. fwohci0) and fc->bdev (i.e. firewire0).
- Remove unused firewirebusreg.h.
- Reduce size of descriptor block for asynchronous transmit and
check the number of descriptor when copying from mbuf.
- Skip mbuf whose length is zero. NFS seems passing such mbuf and
some chips generates unrecoverable error.
- Restore pci config registers after resume.
- Reinitialize and start rx buffers after resume.
- Don't reallocate memory in fwohci_db_init() if the dbch is
already initialized.
- Fix typo.
- Some clean up.
positions for the status bits of port a and port b are different. To
avoid needing to know which channel the interrupt handler is working on,
shift the status bits for port a into the port b bit positions, and always
check the port b status bits. This fixes using port b, which I neglected
to test before.
- Remember to update the channel's tty structure from the passed in termios
in the param routine.
- Minor style.
Metricom Ricochet GS modem. Add them here.
# A new umodem appears to be needed to make the sanyo phone work, but that's
# more extensive and will come after coordination.
With a 1 byte transmit fifo, 3 byte receive fifo, and wierd multiplexed I/O
designed for a Z80 cpu, this chip redefines suckage.
Based on the openbsd and netbsd drivers. Only really works as a console,
modem support is not complete since I can't test it.
this was causing filedesc work to be very painful.
In order to make this work split out sigio definitions to thier own header
(sigio.h) which is included from proc.h for the time being.
for the raidctl device.
Select a more conservative default for the permissions for /dev/raidctl
since the operations are performed using ioctl() not read() and write().
Submitted by: kris
Reviewed by: scottl
Use BUS_SPACE_MAXSIZE_32BIT for the parent dma tags, and
(NSEGS - 1) * PAGE_SIZE for the data buffer tags. FreeBSD/sparc64 is
more strict about checking these values that other arches.
were sometimes propagated using M_COPY_PKTHDR which actually did
something between a "move" and a "copy" operation. This is replaced
by M_MOVE_PKTHDR (which copies the pkthdr contents and "removes" it
from the source mbuf) and m_dup_pkthdr which copies the packet
header contents including any m_tag chain. This corrects numerous
problems whereby mbuf tags could be lost during packet manipulations.
These changes also introduce arguments to m_tag_copy and m_tag_copy_chain
to specify if the tag copy work should potentially block. This
introduces an incompatibility with openbsd which we may want to revisit.
Note that move/dup of packet headers does not handle target mbufs
that have a cluster bound to them. We may want to support this;
for now we watch for it with an assert.
Finally, M_COPYFLAGS was updated to include M_FIRSTFRAG|M_LASTFRAG.
Supported by: Vernier Networks
Reviewed by: Robert Watson <rwatson@FreeBSD.org>
work. The interface was gleaned from the Linux driver. Currently only
one RX & one TX buffer are used. Firmware support is not tested so for the
MPI-350 so it is disabled. Signal cache and monitor mode are not supported
yet. Signal cache is not supported since in encapsulation mode ethernet
frames are returned by the chip. LAN monitor mode support will be added
shortly. Thanks to Warner for the MPI-350 card he sent me.
Add support for RSSI map from PR kern/32880 which was incomplete. Enhanced
with the ability to select the cache mode of raw, dbm or per-cent.
Clean up Signal/Noise/Quality structures and units with help from
Marco Molteni.
Change flash to use a malloc'ed buffer when needed.
PR: kern/32880
Submitted by: Douglas S. J. De Couto decouto@pdos.lcs.mit.edu,
Marco Molteni
MFC: 3 weeks
than hard-coded uids and gids.
Switch the device to a group of wheel instead of operator.
Narrow down the permissions on the device to require root privilege
to manipulate the system power state. It may be that we can broaden
access to the device after review of the access control in ACPI.
Submitted by: kris
Reviewed by: takawata
with make_dev(). Use OPERATOR instead of implicit WHEEL to match
other storage devices. Use a mode of 0640 to be consistent
with other storage devices.
Submitted by: kris
Reviewed by: scottl
Remove the setgid bit from the tga device (?).
Synchronize mode with modes used for related frame buffer devices
in MAKEDEV (tga doesn't appear in MAKEDEV).
Submitted by: kris
improves protection consistency with other storage devices (generally
root:operator,660). This driver appears not to have an active
maintainer.
Submitted by: kris
command in case this setting was not saved. Since bandwidth reclamation
(-current only) often results in bus activity continuing to the end
of every frame, most transfers would fail with IOERROR if this
setting is missed.
Reviewed by: n_hibma
MFC after: 1 week
- Fix permission of device node.
fwochi.c, fwohcireg.h
- Detect phy access failure correct way.
- Set root hold-off bit before initiating bus reset.
This should fix the problem with VIA6306.
fwohcivar.h
- Fix over-allocation of array. (fwohcivar.h)
sbp.c
- Return CAM_DEV_NOT_THERE rather than CAM_TID_INVALID to prevent retry.
- Added support for ITR (interrupt throttle register). This feature is available on
adapters based on 82545 and above
- Fixed problem with vlan support when traffic has priority bits set. (kern/45907)
PR: kern/45907
MFC after: 1 week
I/O port range, then we should ignore a resource if it's NOT
a memory range AND NOT an I/O port range.
The OR in the condition caused us to ignore perfectly valid
memory addresses.
While here, remove redundant parenthesis and reindent the
debug print to avoid long lines.
identify themselves as serial cards that it would be desirable to
attach a different driver than sio to. Since we are claiming all
serial cards, this is not possible. Instead, return -100 to indicate
that we're willing to take the card, but still allow other drivers to
attach.
Pointed out by: Maksim Yevmenkin
not < the size of the device. This avoids geom complaints.
Fix a serious bug in the handling of the RS_NO_CLEAR_UA quirk. When we
go and insert the test-unit-ready command the umass_cam_quirk_cb() function
sets the status as if the READ_CAPACITY command suceeded when, in fact, it
did not. This leads to the CAM layer trying to use garbage in the return
buffer and panicing the system (or doing other bad things).
Add a quirk entry for MSYSTEMS DISK-ON-KEY, which is sold under the Sony
brand as a solid state disk-on-key usb device. This device requires
several quirks to work properly.
Note that the disk-on-key device will not work properly until CAM also
gets a quirk entry for it, which has been submitted to the CAM maintainer,
and you may have to temporarily uncomment the DELAY() as well. -current
does not properly wait for devices to power up so you may also have
to temporarily uncomment the DELAY(300000) to make your device work.
A solution must be found to that issue.
MFC after: 3 days
X-MFC note: the quirk support must MFCd before this patch can be
the dataphysend calculation could only possibly work if the virtual buffer
is also physically contiguous. Calculate dataphysend by calculating the
ending virtual address first, then converting to a physical address.
The second bug applies only to NetBSD and OpenBSD and involves the curlen
calculation in the two-contiguous-physical-pages case (which we don't support).
Also cleanup the use of the OHIC_PAGE() macro on dataphysend and add a panic
if len goes negative (meaning we lost the physical page translation
representing the end of the buffer).
IMHO the dataphysend is still bokered since it might be misrepresented
by shared userland page mappings. The whole section needs to be rewritten
to use the virtual address range.
MFC after: 3 days
prototype for trm_detach and freeing all resources.
While I'm there, handle better errors in trm_attach and remove the
PCI_BASE_ADDR0 definition, since it's what PCIR_MAPS is used for.
MFC after: 3 days
kernel memory allocator, is harmless. This could be a problem for
other systems, though. I've modified Darren's patch a little.
Original patch by: Darren Schack, Isilon Systems, Inc <darrens@isilon.com>
Also analysed by: SGI, and in particular Divy Le Ray of SGI
OK'ed by: re(rwatson)
as module. This also fix's issue kern/45713.
Fix - polling was implemented incorrectly for
adapter enquiry and adapter flush.
(2) Problem: PANIC when unloading driver
as module.
Fix - device nodes are not destroyed for amr0,
and amrd* when driver is unloaded
(3) Problem: PANIC from loading driver when
3ware adapter present, error message "Warning
"amrd is usurping twed's bmaj"
Fix - put #idef freebsd version < 500000 for
bmaj -1 -> amrd_cdevsw
(4) Problem: warnings in driver when compiling
with DAMR_DEBUG param enabled in Makefile
Fix - fix the warnings so driver can compile
when -Werror is present in Makefile.
Approved by: jhb
MFC: 7 days
labels are acurate in relation to a fully compiled
sequencer program (all patches downloaded). Correct
a few occurances of a relative jump across a macro
that ended up jumping us into the last instruction
of the macro.
Spproved by: re (bmah)
ahd_pci.c:
Retrieve the allow_memio hint from the resource manager to
determine whether or not to try PCI MEMIO.
aic79xx_osm.h:
aic7xxx_osm.h:
Don't wrongly abuse the callout_reset() interface when trying
to abuse timeouts generated from the CAM layer. This fixes the
console freeze and lost timeout problem that many have reported,
especially on SMP systems.
aic79xx_pci.c
aic7xxx_pci.c
Rewrite the MEMIO test routine to prevent certain broken chipsets
from trying to burst multiple DWORDs to the registers. Also make
the routine better detect byte merging by the host bridge and
deal with it.
aic79xx.reg:
Correct an incorrect register definition.
Approved by: re (rwatson, jhb)
This mostly consists of functionality to serialize accesses to
the two ATA channels (which can also be used to "fix" certain
PCI based controllers).
Add support for Acard controllers.
Enable the ATA driver in PC98 GENERIC, and add device hints.
Update man page with latest support.
The PC98 core team has kindly provided me with a PC98
machine that made this all possible, thanks to all that
contributed to that effort, without that this would
probably newer have been possible..
Approved by: re@
We allow the request to go through if it matches either a prefetchable
or a non-prefetchable part of the bridge. We do not check to make
sure it is the right kind of memory because most drivers to not yet
properly set RF_PREFETCHABLE (only cardbus seems to do so, and I'm not
entirely sure it does it right). RF_PREFETCHABLE was invented for
cardbus, so hasn't been properly documented yet.
This is still overridable by hw.pci.allow_unsupported_io_ranges, but
the need for that is greatly reduced, especially for the nvida driver.
Approved by: re
Reviewed by: jhb and many testers
Submitted by: Matt Emmerton (although this has been reworked somewhat)
could already exist, and this triggers a booby trap panic in make_dev.
remove_plex_entry: Don't remove the stripe mutex here, it gets done in
free_plex.
Approved by: re (rwatson)
the device is not actually present), clear the corresponding bit in
the ch->devices bitmap. This resolves a panic that occurred with ATAPI/CAM
after an APM suspend/resume, when the ATA hardware would erroneously
report an extra ATAPI device.
Approved by: re, sos
Reviewed by: roberto
MFC after: 7 days
version, plus add support for the new features found in the Rev B
version of the chip. The changelog is quite long and can be provided
on request. Major features include vastly improved protocol violation
handling, full support for the 7902 Rev B, better parity error
handling, and better packetized overrun handling, to name a few.
Approved by: re (blanket)
HP -> CPQ
Rearrange IDs to better match which chips they use.
Convert to uniform product description strings.
Simplify 7901A setup function.
Add the NONPACKFIFO_BUG and PACED_NEGTABLE_BUG entries
for the A.
Add rev B bugs and features.
The double write workaround for CURRSCB is only required if
abort pending is set. Remove this work around and set the
abort pending bug bit on the B at least until we have better
confirmation that the double write is always safe.
Add updated H2B identifiers
Move IOCell paramters into softc and add a hook for the
OSM to modify these as well as other settings prior to
committing them to the chip.
SLEW -> SLEWRATE
PREQDIS in DEVCONFIG1 went away after the A2.
Remove all code that references this bit. This
is especially important since this bit was reused
in the B for a different HW fix workaround.
Properly set the AHD_NEW_IOCELL_OPTS and
AHD_NEW_DFCNTRL_OPTS features for the B.
Remove stray/random extra 7901A generic PCI
table entry. Also switch the correct 7901A
generic entry to use ID_ALL_MASK since we
can only differentiate the 7901A from the
7902 by checking for a "type field" of 0xE.
Set AHD_INTCOLLISIONT_BUG for the Rev B.
Set the PREQDIS bit in DEVCONFIG1 for the B. The
bit is misnamed, but seems to disable a work-around
that breaks on the B on PCI busses.
Add a routine for testing memory mapped register access.
This will hopefully detect things like buggy via chipsets
so that the OSM can fallback to using I/O mapped access
when memory mapped I/O simply will not work.
Approved by: re (blanket)
diagnostic "Setting Mode" messages.
Use a read of HCNTRL to flush our write to CLRCMDCMPLT
on the RevB. This allows us to check to see if the sequencer
is paused and to initiate the interrupt collision workaround
without incuring an extra read.
Approved by: re (blanket)
PCI-X only workarounds are automatically masked out
if we are operating in PCI mode.
Make use of ahd_pci_test_register_access()
Approved by: re (blanket)
Move IOCell paramters into softc and add a hook for the
OSM to modify these as well as other settings prior to
committing them to the chip.
Approved by: re (blanket)
in the per-device kthread. This ensures that synchronisation with
mddestroy() succeeds even if the kthread was not waiting in tsleep()
at the time of the wakeup(). Among other things, this fixes the
problem of mdconfig getting stuck when an attempt is made to use a
zero-length file as a vnode-type backing store.
Approved by: re
aic7xxx.c:
aic7xxx.h:
aic7xxx.reg:
aic7xxx.seq:
Bring in the protocol violation handler from the U320
driver and replace the NO_IDENT sequencer interrupt code
with the PROTO_VIOLATION code. Support for this code
required the following changes:
SEQ_FLAGS:
IDENTIFY_SEEN -> NOT_IDENTIFIED
Added NO_CDB_SENT
SCB_CONTROL:
TARGET_SCB == STATUS_RCVD for initiator mode
scb->flags:
Added SCB_TARGET_SCB since we cannot rely on
TARGET_SCB as a target/initiator differentiator
due to it being overloaded in initiator mode to
indicate that status has been received.
aic7xxx.seq:
Move data fifo CLRCHN to mesgin_rdptrs which is a safer
location for doing this operation. This also saves a
sequencer instruction.
aic7xxx.c:
aic7xxx.h:
Change ahc/ahd_upate_neg_request() to take a "negotiation
type" enum that allows us to negotiate:
o only if the goal and current parameters differ.
o only if the goal is non-async
o always - even if the negotiation will be for async.
aic7xxx.seq:
Reset the FIFO whenever a short CDB transfer occurs
so that the FIFO contents do not corrupt a future CDB
transfer retry.
Add support for catching the various protocol violations
handled by ahc_handle_protocol_violation.
Reformat some comments.
aic7xxx.c:
aic7xxx.h:
Just for safety, have the aic7xxx driver probe
the stack depth.
aic7xxx.c:
aic7xxx.h:
Save and restore stack contents during diagnostics.
Some chip variants overwrite stale entries on a
stack "pop".
Don't use 0 to probe the stack depth. 0 is the typical
value used to backfill the stack if entries are overwritten
on a "pop".
aic7xxx.h:
Add a missing typedef.
Collapse SCB flag entries so they are bit contiguous.
Add AHD_ULTRA2_XFER_PERIOD for narrow fallback calculations
aic7xxx.c:
Don't panic (as a diagnostic to catch bugs) if we decided to
force the renegotiation of async even if we believe we are
already async. This should allow us to negotiate async instead
of the full user goal rate during startup if bus resets are
disabled.
Add a space to the end of the ahc/ahd_print_devinfo routines
so that it behaves as expected by the code that uses it.
Only force a renegotiation on a selection timeout
if the SCB was valid. Doing otherwise may be dangerous
as the connection was not valid for an unknown reason.
Add additional diagnostic output to ahc_dump_card_state(),
and have it use the register pretty printing functions.
Update ahc_reg_print() to handle a NULL cur_col.
Add a newline to ahc_dump_card_state() output.
Bring back "use_ppr". We need to use_ppr anytime
doppr is true or we have non-zero protocol options.
The later case was not handled in the recent removal
of use_ppr.
Move a comment and remove a useless clearing of use_ppr.
Don't disable ENBUSFREE when single stepping on
a DT capable controller. We cannot re-enable unexpected
busfree detection, so we must clear BUSFREE on each
step instead.
Correct the lookup of the SCB ID in ahc_handle_proto_error.
Remove a diagnostic printf.
Remove unecessary restoration of the STACK for older
chips.
Approved by: re (blanket)
This will hopefully detect things like buggy via chipsets
so that the OSM can fallback to using I/O mapped access
when memory mapped I/O simply will not work.
Approved by: re (blanket)
AHC_ALLOW_MEMIO is set, or the hint hint.ahc.N.allow_memio=1 is
set in the bootloader.
Make use of ah?_pci_test_register_access().
Approved by: re (blanket)
o Add needed headers.
o Add stg_products[] product data and stg_match() function.
o Change stg_pccard_method[] to support both OLDCARD and NEWCARD.
Approved by: re
o Add needed headers.
o Add ncv_products[] product data and ncv_match() function.
o Change ncv_pccard_method[] to support both OLDCARD and NEWCARD.
Suggestion for REX-5572 matching part by imp.
Approved by: re
o Add needed headers.
o Add nsp_producs[] product data and nsp_match() function.
o Change nsp_pccard_method[] to support both OLDCARD and NEWCARD.
o Add warning to fall back to PIO mode when it cannot use SMIT mode.
This is needed because memories are not allocated with NEWCARD now.
Submitted by: takawata
Approved by: re
or stg driver. They are,
Macnica mPS110, PANASONIC(KME) KXLC004, Qlogic Fast SCSI,
Workbit Ultra Ninja-16, (ID based)
Future Domain SCSI2GO, IBM SCSI PCMCIA card, I-O DATA CBSC16,
Macnica mPS100, Newmedia BASICS-SCSI, RATOC REX-5536, RATOC REX-5536AM,
RATOC REX-5536M, RATOC REX5572, Workbit NinjaSCSI-3
(CIS based)
Note: We need vendor IDs WORKBIT2 and IODATA3 which is -1, since some
cards does not have IDs in the CIS and fails to be probed without
this fake vendor IDs.
o Change the strings of RATOC REX_R280 from REX-R280 to REX-R280/REX-9530.
This reminds us that REX-R280 and REX-R9530 have same ID (same product).
Reviewed by: imp
Approved by: re
Obtained from: /etc/defaults/pccard.conf,
List of CIS tupples by Toshihiko ARAI and PAO project:
http://www.linkclub.or.jp/~clover/cis/
Change suggestion by: HASEGAWA Tomoki <thasegawa@mta.biglobe.ne.jp>
for I-O DATA CBSC16 entry
There were no serious problem reports on this in spite of my concern.
To get debug output from acpi_pci_link, just enable bootverbose flag
in usual manner (boot -v).
Approved by: re
aicasm_gram.y:
Use a direct move from allzeros to emulate a
mvi of 0.
aicasm_insformat.h:
sync $Id$
aicasm_symbol.c:
Minor header change.
Approved by: re (blanket)
pci_get_ether accesor, which gets it from the CIS for cardbus cards
(and from other pci-like buses via whatever mechanism is used there).
Submitted by: sam
Approved by: re (blanket)
sometimes, so return it when requested and it does. Also a little
more infrastructure for a few other things.
Submitted by: sam
Approved by: re (blanket for NEWCARD)
buses support querying the MAC address in a standard-for-that-bus way.
The base pci bus returns NULL for this IVAR always.
Submitted by: sam
Approved by: re (blanket for NEWCARD)
- If a PCI device is not present, then a 32-bit read_config() is going to
return 0xffffffff not 0xffff.
- For the 82454NX chipset, the MIOC that we read the bus numbers of the
various host-PCI bridges from is at function (slot) 0x10 not 0x0.
Approved by: re (rwatson)
1. Detect the revision of the Rhine chip we're using.
2. Use the force reset command on revisions which support
it whenever the normal reset command fails.
This should solve a wide range of "my vr0 locks up with reset
failed messages" problems. (Although the root causes should
be eventually tracked down.)
Tested by: grenville armitage <garmitage@swin.edu.au>
Obtained from: Via's if_fet driver
MFC after: 3 days
Approved by: re
If the value from the user is less than 177, assume it is a multiple of
a single speed CDROM and convert to KB/sec.
No complaints from: sos
Reviewed by: ken
Approved by: re
MFC after: 1 day
to PCI bridge can be read be evaluating the _BBN method of the host to PCI
device. Unfortunately, there appear to be some lazy/ignorant/moronic/
whatever BIOS writers that return 0 for _BBN for all host to PCI bridges in
the system. On a system with a single host to PCI bridge this is not a
problem as the child bus of that single bridge will be bus 0 anyway.
However, on systems with multiple host to PCI bridges and l/i/m/w BIOS
writers this is a major problem resulting in all but the first host to
PCI bridge failing to attach. So, this adds a workaround.
If the _BBN of a host to PCI bridge is zero and pcib0 already exists
and is not us, the we use _ADR to look up our PCI function and slot
(we currently assume we are on bus 0) and use that to call
host_pcib_get_busno() to try and extract our bus number from config
registers on the host to PCI bridge device. If that fails, then we make
an evil assumption that ACPI's _SB_ namespace lays out the host to PCI
bridges in ascending order and use our pcib unit number as our bus
number.
Approved by: re
after configure() has run. Only create the device if ofwcons is the
highest priority console. Make a dev alias with the same name as the
firmware output-device property.
trigger a breakpoint with this chip.
- Fiddle the right bits in the cn input and output routines to disable port
interrupts and enable visibility of the masked interrupt status bits.
- Register a shutdown final event handler to put the chip back in the mode
that the prom expects.
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes
Reviewed by: many
Approved by: re
o Use 32-bit unsigned types for things that really are 32-bit quantities,
not bus_addr_t. These are not the same as a bus_addr_t, so don't use
that here. Harmless on i386, introduced problems on sparc64.
Submitted by: jhb
bit in the PCI command register for the device. Otherwise, device drivers
that look at this register to see which types of BARs are usable will think
that none of them are.
This allows my Adaptec 1480A cardbus card to finally work.
Reviewed by: imp
alpha. This will take the file out of sync with the private version
that we maintain, but alpha tinderbox has been broken for too long.
Tested on: i386, sparc64, alpha
- Fix some especially bad style in the CIS BAR tuple parsing code.
- activate Option ROMS correctly.
- de-obfuscate the Option ROM image selection code.
- Fix mis-interpretation of the PCI spec that prevented Option ROMs whose
CIS section wasn't in the first image from working.
- Fix mis-interpretation of the PCI spec that prevented CIS's mapped into
MEMIO space from working at all.
- Reject invalid CIS pointers.
Reviewed by: imp
- Set RDTR to zero by default instead of 28.
- Fixed a problem with TX hangs with jumbo frames when number of fragments in the mbuf chain
is large.
- Added support for 82540EP based cards.
MFC after: 3 days
is not long long on all archs. (They happen to be long's on 64-bit arch's
and gcc considers that significant enough to warn about it.) These should
probably be uintmax_t but I didn't feel like adding all the extra includes.
these were cosmetic. However, at least two of these changes fix bugs
where a (fake) pointer to a RX descriptor was added to the physical
memory start address with the cast in the wrong place resulting in
rxdesc[pmem_start] instead of (uintptr_t)rxdesc + pmem_start.
just limited to the DEVICE_POLLING case. This removes the FXP_RFA_RNRMARK
hack, and replaces it with a softc flag that is used to record when
the handling of a no-resource condition was deferred due to running
out of DEVICE_POLLING cycles. This was tested on -stable, but the
code is essentially the same as in -current. It should only affect
the case where DEVICE_POLLING is defined.
The details of the mechanism behind the crashes are still uncertain
but the most likely cause seems to be some kind of hardware confusion
when the no-resource recovery code is accidentally invoked while
the receiver is still active. This could have happened if the
hardware left the 0x4000 bit of the RFA status word set. The comments
in the commit log for revision 1.142 stating that the driver could
clash with the hardware writing to this status word were not correct.
Tested by: Guy Helmer <ghelmer@palisadesys.com>
from being MI in any fashion. It currently "assumes" that it can get
a kernel virtual address for a phyiscal address by adding KERNBASE to the
physical address. It also tries to read values out of a the PC BIOS on
all archs. It also uses "manual" inb() and outb()'s to talk to the mcclock
device which just happens to be at that location on both i386 and alpha.
This driver should likely be i386-only.
acpi_cmbat_init_battery() and acpi_cmbat_init_acline() respectively.
Call acpi_cmbat_init_battery() from acpi_cmbat_resume() too just in
case.
This is a workaround for embedded controller operations which is
unstable for about a minute (typically 30 or 40 sec.) at boot time.
o Always release the resources on device detach.
o Attach resources the same with driver added as we do we do in the insert
case (maybe this should be a routine).
o signal the wakeup of the thread on resume instead of trying to force an
interrupt.
o Minor debug hacks.
o use 0xffffffff instead of -1 for uint32_t items.
o Don't complain when we're asked to detach no cards. This is normal.
o Eliminate the now worthless second parameter to card_detach_card.
o minor style(9)isms
Some of these patches may be from: iwasaki-san, jhb, iadowse
state. Instead, use ACPI_STA_PRESENT and ACPI_STA_FUNCTIONAL for it.
In some ACPI BIOS implementations, boot disabled devices don't have
ACPI_STA_ENABLE bit in _STA object.
Also it is not fatal if getting current IRQ of boot disabled devices
is failed in initial state.
And minor fixes.
amr_cam.c,
amrreg.h,
amrvar.h:
- added support for 12/16 byte cdb's, effecting CAM branch only ( non-disk support )
amrreg.h:
- increased number of scatter gather elements from 16 to 26.
amr_pci.c:
- amr_pci_free(), incorrect bus tag meant for 'amr_mailbox_dmat' was being freed
all:
- copyright change requested by scottl
Reviewed by: ps,scottl
MFC after: 1 week
across system suspends on the Intel 82371AB PCI-ISA bridge. On a
Sony Vaio C1XD that I have, these registers are not set correctly
after an ACPI resume. The result is that after resuming, a shared
IRQ is left in edge-triggered mode so the interrupt can later become
jammed in a state where the line remains asserted, but the handler
is never called.
Reviewed by: jhb
behaviour of the hardware: a possibly reserved bit of the receive
descriptor (RFA) `status' field is borrowed to record no-resource
(RNR) events, and the same status field is read and written to at
a time that may clash with the hardware updating this field.
There is no hardware documentation available to determine if these
things are safe to do; the second issue almost certainly isn't, and
the first is only safe if there is documentation saying that this
bit is free to be used by the driver. The PR referenced below
provides extremely convincing evidence that the changes cause random
crashes on some (unusual) hardware.
Since these features are only required by the DEVICE_POLLING case,
this commit makes their use conditional on that option. It does not
change the DEVICE_POLLING case, but at least people with the rare
hardware on which this code causes problems can now avoid the crashes
by not enabling DEVICE_POLLING.
PR: kern/42260
Reviewed by: luigi
Problem revision found by: Pawel Malachowski <pawmal@unia.3lo.lublin.pl>
Tested by: Pawel Malachowski <pawmal@unia.3lo.lublin.pl>
MFC after: 1 week
pipe callback function, and just return if these cases are detected.
Without these checks, the ulpt driver may cause an infinite loop
of failing USB transfers that can hang the whole machine. This makes
printing work for me on a HP DJ950C printer.
- Add detach support to the driver so that you can kldunload the module.
Note that currently rc_detach() fails to detach a unit if any of its
child devices are open, thus a kldunload will fail if any of the tty
devices are currently open.
- sys/i386/isa/ic/cd180.h was moved to sys/dev/ic/cd180.h as part of
this change.
Requested by: rwatson
Tested by: rwatson
and XPT_RESET_DEV.
In order to properly handle reset requests whether they originate in the
ATA layer (atacontrol reinit) or from the CAM layer (camcontrol reset)
ata_reinit does not cause the SIM to be deallocated anymore. The SIM
is now unconditionnally created for each ATAPI bus.
This change may cause existing bus ids to change on some setups.
Reviewed by: roberto
Approved by: sos
creation by GCC-2.6.3. Casting pointers to unsigned char
to volatile pointers to unsigned char seemed to produce
better results on the ia32 architecture with old versions
of GCC.
The current FreeBSD system compiler GCC-3.2.1 emits
better sign extension code for non-volatile variables:
volatile char c;
int i = c;
is compiled to:
...
movb -1(%ebp), %al
movbsl %al, %eax
movl %eax, -8(%ebp)
...
char c;
int i = c;
is compiled to:
...
movbsl -1(%ebp), %eax
movl %eax, -8(%ebp)
...
The same holds for zero-extension of dereferenced pointers
to volatile unsigned char.
When compiled on alpha or sparc64, the code produced for the
two examples above does not differ.
* Change atapi-cd ioctls to use the same units.
* Change burncd, cdcontrol to convert CDROM speed to KB/sec before
calling the ioctl. Add a "max" speed option for their command lines.
This change does not break ABI but does change the units passed through
the ioctl so 3rd party software that uses cdrio.h will have to convert
(most likely by multiplying CDROM speed by 177 to get KB/s).
PR: kern/36845
Submitted by: Philipp Mergenthaler <p@i609a.hadiko.de> (CAM ioctls)
Reviewed by: sos, ken
MFC after: 1 month
changes for "LSILogic"
(2) enabled non-disk support through CAM interface
(3) HA_INQ (a) enabled tagged queuing (b) disable reset during
driver loading (b) renamed BSDi string to LSI
(4) disabled detecting disk devices during SCSI INQUIRY
(5) changed dcdb single element sglist to send one entire buffer chunk
(6) nsgelem not set in sglist
(7) ap_data_transfer_length not set for dcdb
(8) changed "struct thread" to "d_thread_t" for compatibliity { xxx_open,
xxx_close, xxx_ioctl }
(9) miscellaneous compatiblity fixes
(10) bug fix for 0x0409/0x1000 card
(11) added compiling amr_cam.c in sys/conf/files
(12) added compiling amr_cam.c in sys/modules/amr/Makefile
Reviewed by:ps
MFC after:1 week
1 week
In that case use proc0's pid to return the thread ID.
- For 4-stable, use the generic swi taskqueue for ACPI events rather than
implementing our own.
Sponsored by: The Weather Channel
o instead of a list of mbufs use a list of m_tag structures a la openbsd
o for netgraph et. al. extend the stock openbsd m_tag to include a 32-bit
ABI/module number cookie
o for openbsd compatibility define a well-known cookie MTAG_ABI_COMPAT and
use this in defining openbsd-compatible m_tag_find and m_tag_get routines
o rewrite KAME use of aux mbufs in terms of packet tags
o eliminate the most heavily used aux mbufs by adding an additional struct
inpcb parameter to ip_output and ip6_output to allow the IPsec code to
locate the security policy to apply to outbound packets
o bump __FreeBSD_version so code can be conditionalized
o fixup ipfilter's call to ip_output based on __FreeBSD_version
Reviewed by: julian, luigi (silent), -arch, -net, darren
Approved by: julian, silence from everyone else
Obtained from: openbsd (mostly)
MFC after: 1 month
of KBDIO_DEBUG which may be defined in the kernel config (as it is in NOTES).
This kind of bug is a _really_ horribly thing as we end up with one bit
of code thinking a particular structure is 136 bytes and another that it
is only 112 bytes.
Ideally all places would remember to #include the right "opt_foo.h" file,
but I think in practice file containing the variable sized struct should
#include it explicitly as a precaution.
Detected by: FlexeLint
pci_cvt_to_bwx.
This doesn't necessarily make bge(4) now actually *work* on an alpha.
It loads, configures, and then about 30 seconds later, my XP1000 hard
freezes. But, hey, it's a start.
Obtained from: gallatin@freebsd.org
clear the bit. This allows ata driver to attach its children because
it needs the interrupts enabled to succeed.
Submitted by: iwasaki-san
o Spell CardBus as CardBus, not Cardbus or CardBUS while I'm here.
The problem is that the code does a check for the granparent of
the Promise chip, if this is a bridge of the right type, we have
a TX4 on our hands, and need to handle that ones "issues".
Now the grandparent check cause subtle bugs in the newbus system,
mainly that pci_get_devid doesn't return an error value.
This patch works around the issue by using BUS_READ_IVAR() instead.
o Implement the thread killing interlock as described by jhb in arch@
while talking to markm.
o Hold Giant around cbb_insert()/cbb_remove(). Deep in the belly of
the vm code we panic if we don't hold this when we activate the memory
for reading the CIS.
o If we had to do the kludge alloc, then do a kludge free.
o Better resume code. Move the comments around. Force the socket state to
be querried. Ack the interrupts properly.
o Intercept the interrupt requests and keep a list of interrupts to service
ourselves. When the card attaches, set its OK bit. When we get a card
status change interrupt for that card, clear the OK bit. Don't call the
ISR if the OK bit is cleared. Iwasaki-san and yamamoto-san have both
sent me patches that fix the same problem this fixes, but at the pccard
level.
o Try to get the signalling of the thread to actually die. This might not be
100% right, but it is less wrong than before.
o Add a SIC next to a TI type that looks like it could be wrong, but isn't.
the card.
o Add comments about how we're doing the CIS activation.
o Add location and pnp info functions.
o Add better code to hopefully deal with ata cards better (and other drivers
that allocate resources that we didn't preallocate from the CIS). OLDCARD
used to allow it, but NEWCARD was pickier. I'm not 100% sure this works,
but it doesn't break anything.
give us slightly better error checking than before and interpret what
default bits mean better. See the NetBSD CVS tree for the authors of
these changes (revs 1.10 .. 1.17).
Note, we return the PCI pnp info, but in fact that's wrong to do
since that data is not defined for CardBus cards. CardBus says that
these registers are undefined and one should use the CIS to do
device matching. To date, all CardBus cards have had these
registered defined, no doubt because they are using common silicon
to produce both the PCI cards and the CardBus cards. However, it isn't
any worse than the rest of the system, so just note it in passing and
move on.
o Also sort prototypes while I'm here.
currently disabled):
o Don't use constants for the output parameter, use the iparam count as a
pointer to the first result location.
o Fix bits vs bytes counting problems.
o Split out the hardware and software normalization versions of modexp.
o Enable hardware normalization for chips that support it.
o On reset, disable hardware normalization for 582x and make sure the
chip is in little endian mode.
o Since sw normalization is now the only option, simplify normalization
handling.
Also fix RNG harvesting: disabling PK support (for the moment) had disabled
the MCR2 interrupt; consider both KEY support and RNG support when deciding
whether or not to enable it.
Obtained from: openbsd
OpenBSD who got the code (or the idea) from the NetBSD tlp driver.
This gets some cardbus dc cards working (either completely or nearly
so). It also appears to get additional pci cards working, without
breaking working ones.
# Maybe some additional work is needed here. Also, the cardbus attachment
# might need to match on the CIS rather than on the vendor/device so we have
# a finer level of detail as to what the card is. Technically, the
# vendor/device fields are undefined for CardBus (even though most cards are
# using common silicon with pci models).
NB: But it will enable it in all kernels not having options "NO_GEOM"
Put the GEOM related options into the intended order.
Add "options NO_GEOM" to all kernel configs apart from NOTES.
In some order of controlled fashion, the NO_GEOM options will be
removed, architecture by architecture in the coming days.
There are currently three known issues which may force people to
need the NO_GEOM option:
boot0cfg/fdisk:
Tries to update the MBR while it is being used to control
slices. GEOM does not allow this as a direct operation.
SCSI floppy drives:
Appearantly the scsi-da driver return "EBUSY" if no media
is inserted. This is wrong, it should return ENXIO.
PC98:
It is unclear if GEOM correctly recognizes all variants of
PC98 disklabels. (Help Wanted! I have neither docs nor HW)
These issues are all being worked.
Sponsored by: DARPA & NAI Labs.
(1) Use namei() and devfs to discover devices rather than a hard-coded
MAKEDEV implementation. Once rootfs is in place, this will allow
Vinum to be used for the root file system partition.
(2) Pass FREAD to device opens so that GEOM will return sector size
rather than an error on attempts to read label data.
(3) Avoid clobbering return values from close_drive() and masking this
failure, resulting in a later divide by zero due to not having
updated the Vinum-cached sector size.
(4) Ignore failures from DIOCWLABEL as that appears not to be required
in the GEOM environment.
We've done testing in simple Vinum environments, but those with more
complex environments might want to give this a spin in DP2 and make
sure everything is up to speed.
Fixes in collaboration with: iedowse
Reviewed by: grog
before freeing so that WITNESS doesn't dereference mutex data pointers
and page fault. It's now possible to unload vinum.ko with a GENERIC
kernel on 5.0-CURRENT without panic.
Debugged/fixed with the aid of: jake, grog
This allocate the best IRQ to boot-disable devices (have IRQ 0).
Allocated IRQ will be used for PCI interrupt routing when ACPI is
enabled.
Note that verbose messaging enabled for the time being so that
people can easily notice the strange behavior if it happened.
dereference the struct sigio pointer without any locking. Change
fgetown() to take a reference to the pointer instead of a copy of the
pointer and call SIGIO_LOCK() before copying the pointer and
dereferencing it.
Reviewed by: rwatson
doesn't give them enough stack to do much before blowing away the pcb.
This adds MI and MD code to allow the allocation of an alternate kstack
who's size can be speficied when calling kthread_create. Passing the
value 0 prevents the alternate kstack from being created. Note that the
ia64 MD code is missing for now, and PowerPC was only partially written
due to the pmap.c being incomplete there.
Though this patch does not modify anything to make use of the alternate
kstack, acpi and usb are good candidates.
Reviewed by: jake, peter, jhb
supported option and it disabled a whole 2 lines of bootverbose messages.
I wanted to see 1 of the messages (about the latency timers). This
is a wrong place to decode pci configurations, but the code is already
here and handles more details than pciconf(8).
A number of functions in this driver still use the unit number in their
printouts because they pass the unit directly as a function argument
instead of passing a softc or struct ifnet pointer. This should be
resolved at a future date.
code path to fix a bug in the non USB_USE_SOFTINTR path that caused
the usb bus to hang and generally misbehave when devices were unplugged.
In the process though it also reduced the throughput of usb devices because
of a less than optimal implementation under FreeBSD.
This commit fixes the non USB_USE_SOFTINTR code in uhci and ohci
so that it works again, and switches back to using this code path.
The uhci code has been tested, but the ohci code hasn't. It's
essentially the same anyway and so I don't envisage any difficulties.
Code for uhci submitted by: Maksim Yevmenkin <myevmenk@exodus.net>
testing any modifications to them, they shouldn't even bother with
disklabels in the first place and they are just plain obsolete old
hardware which should be axed entirely before 5.0-R IMO.
Sponsored by: DARPA & NAI Labs.
