the structure definitions come from NetBSD to make it easier to share card
definitions. The driver only acts as a shim between the pci bus and the
sio driver. Later pci parallel ports could also be supported through this
driver. Support for most single and multiport pci serial cards should be
as simple as adding its definition to pucdata.c
Tested with the following pci cards:
Moxa Industio CP-114, 4 port RS-232,RS-422/485
Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports
Netmos NM9835 PCI-2S-550, 2 port RS-232
ACPI_NO_SEMAPHORES, ASR_MEASURE_PERFORMANCE, AST_DEBUG, ATAPI_DEBUG,
ATA_DEBUG, BKTR_ALLOC_PAGES, BROOKTREE_ALLOC_PAGES, CAPABILITIES,
COMPAT_SUNOS, CV_DEBUG, MAXFILES, METEOR_TEST_VIDEO, NDEVFSINO,
NDEVFSOVERFLOW, NETGRAPH_BRIDGE, NETSMB, NETSMBCRYPTO, PFIL_HOOKS,
SIMOS, SMBFS, VESA_DEBUG, VGA_DEBUG.
Start using #! to comment out negative options and ## to comment out
broken options.
atapi-all.c:
Fixed rotted bits that were hiding under ATAPI_DEBUG.
atapi-cd.c:
#include "opt_ata.h" so that ACD_DEBUG is actually visible.
ata/atapi-tape.c
#include "opt_ata.h" so that AST_DEBUG is actually visible.
descriptors. This simplifies code for jumbo frames.
- Cleaned up coding conventions to make code more unix-like.
- Cleaned up code in if_em_fxhw.c and if_em_phy.c.
Added relevant comments.
MFC after: 1 week
feature bit on newer Athlon CPUs if the BIOS has forgotten to enable
it.
This patch was constructed using some info made available by John
Clemens at http://www.deater.net/john/PavilionN5430.html
Reviewed by: -audit
MFC after: 3 weeks
npx is no more mandatory than sc. Its mandatoryness went away in
rev.1.226 of i386/machdep.c 9 months before it was made mandatory in
rev.1.24 of config/mkmakefile.c.
This change is mainly to test building of minimal kernel configurations.
npx should really be even more standard than clk. It was optional mainly
so that the usual device driver configuration info could be specified in
the usual way in config files, but this hasn't been necessary for a few
years.
prior ICP Vortex models. This driver was developed by Achim Leubner
of Intel (previously with ICP Vortex) and Boji Kannanthanam of Intel.
Submitted by: "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com>
MFC after: 2 weeks
Integrated RAID driver, supported by <boji.t.kannanthanam@intel.com> and
<achim.leubner@intel.com>.
Submitted by: "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com>
defined, no symbols are exported from the module. This is
the typical configuration for most device drivers and
standalone modules; only infrastructure modules or those with
special requirements typically need to export symbols.
Don't print the objcopy commands as they are run when converting
symbols; they're bulky and annoying in many cases.
simplifying the module linking process and eliminating the risks
associated with doubly-defined variables.
Cases where commons were legitimately used (detection of
compiled-in subsystems) have been converted to use sysinits, and
any new code should use this or an equivalent practice as a
matter of course.
Modules can override this behaviour by substituting -fno-common
out of ${CFLAGS} in cases where commons are necessary
(eg. third-party object modules). Commons will be resolved and
allocated space when the kld is linked as part of the module
build process, so they will not pose a risk to the kernel or
other modules.
Provide a mechanism for controlling the export of symbols from
the module namespace. The EXPORT_SYMS variable may be set in the
Makefile to NO (export no symbols), a list of symbols to export,
or the name of a file containing a newline-seperated list of
symbols to be exported. Non-exported symbols are converted to
local symbols. If EXPORT_SYMS is not set, all global symbols are
currently exported. This behaviour is expected to change (to
exporting no symbols) once modules have been converted.
Reviewed by: peter (in principle)
Obtained from: green (kmod_syms.awk)
hw.midi.debug and hw.midi.seq.debug to 1 to enable debug log.
- Make debug messages human-frendly.
- Implement /dev/music.
- Add a timer engine required by /dev/music.
- Fix nonblocking I/O.
- Fix the numbering of midi and synth devices.
Remove the explicit call to aio_proc_rundown() from exit1(), instead AIO
will use at_exit(9).
Add functions at_exec(9), rm_at_exec(9) which function nearly the
same as at_exec(9) and rm_at_exec(9), these functions are called
on behalf of modules at the time of execve(2) after the image
activator has run.
Use a modified version of tegge's suggestion via at_exec(9) to close
an exploitable race in AIO.
Fix SYSCALL_MODULE_HELPER such that it's archetecuterally neutral,
the problem was that one had to pass it a paramater indicating the
number of arguments which were actually the number of "int". Fix
it by using an inline version of the AS macro against the syscall
arguments. (AS should be available globally but we'll get to that
later.)
Add a primative system for dynamically adding kqueue ops, it's really
not as sophisticated as it should be, but I'll discuss with jlemon when
he's around.
- Temporary fix a bug of Intel ACPI CA core code.
- Add OS layer ACPI mutex support. This can be disabled by
specifying option ACPI_NO_SEMAPHORES.
- Add ACPI threading support. Now that we have a dedicate taskqueue for
ACPI tasks and more ACPI task threads can be created by specifying option
ACPI_MAX_THREADS.
- Change acpi_EvaluateIntoBuffer() behavior slightly to reuse given
caller's buffer unless AE_BUFFER_OVERFLOW occurs. Also CM battery's
evaluations were changed to use acpi_EvaluateIntoBuffer().
- Add new utility function acpi_ConvertBufferToInteger().
- Add simple locking for CM battery and temperature updating.
- Fix a minor problem on EC locking.
- Make the thermal zone polling rate to be changeable.
- Change minor things on AcpiOsSignal(); in ACPI_SIGNAL_FATAL case,
entering Debugger is easier to investigate the problem rather than panic.
Non-SMP, i386-only, no polling in the idle loop at the moment.
To use this code you must compile a kernel with
options DEVICE_POLLING
and at runtime enable polling with
sysctl kern.polling.enable=1
The percentage of CPU reserved to userland can be set with
sysctl kern.polling.user_frac=NN (default is 50)
while the remainder is used by polling device drivers and netisr's.
These are the only two variables that you should need to touch. There
are a few more parameters in kern.polling but the default values
are adequate for all purposes. See the code in kern_poll.c for
more details on them.
Polling in the idle loop will be implemented shortly by introducing
a kernel thread which does the job. Until then, the amount of CPU
dedicated to polling will never exceed (100-user_frac).
The equivalent (actually, better) code for -stable is at
http://info.iet.unipi.it/~luigi/polling/
and also supports polling in the idle loop.
NOTE to Alpha developers:
There is really nothing in this code that is i386-specific.
If you move the 2 lines supporting the new option from
sys/conf/{files,options}.i386 to sys/conf/{files,options} I am
pretty sure that this should work on the Alpha as well, just that
I do not have a suitable test box to try it. If someone feels like
trying it, I would appreciate it.
NOTE to other developers:
sure some things could be done better, and as always I am open to
constructive criticism, which a few of you have already given and
I greatly appreciated.
However, before proposing radical architectural changes, please
take some time to possibly try out this code, or at the very least
read the comments in kern_poll.c, especially re. the reason why I
am using a soft netisr and cannot (I believe) replace it with a
simple timeout.
Quick description of files touched by this commit:
sys/conf/files.i386
new file kern/kern_poll.c
sys/conf/options.i386
new option
sys/i386/i386/trap.c
poll in trap (disabled by default)
sys/kern/kern_clock.c
initialization and hardclock hooks.
sys/kern/kern_intr.c
minor swi_net changes
sys/kern/kern_poll.c
the bulk of the code.
sys/net/if.h
new flag
sys/net/if_var.h
declaration for functions used in device drivers.
sys/net/netisr.h
NETISR_POLL
sys/dev/fxp/if_fxp.c
sys/dev/fxp/if_fxpvar.h
sys/pci/if_dc.c
sys/pci/if_dcreg.h
sys/pci/if_sis.c
sys/pci/if_sisreg.h
device driver modifications
for use on machines with untrusted local users, for security as well
as stability reasons.
o Lack of clarity pointed out by: David Rufino <dr@soniq.net> via bugtraq.
Assert that compilation takes place in a freestanding environment. This
implies `-fno-builtin'. A freestanding environment is one in which the
standard library may not exist, and program startup may not necessarily be
at main. The most obvious example is an OS kernel. This is equivalent to
`-fno-hosted'.
cardbus in the kernel, not on all the bridges that implement it.
Note: this is NEWCARD only, so we don't want it for the 'card' case,
unlike card_if.m, which is both NEWCARD and OLDCARD.
NEWCARD. Other patches may be reqiured to sio to prevent a hang on
eject. Also add commented out entries for sio_pccard.c in files.pc98
to match other architectures.
Submitted by: yamamoto shigeru-san
kern.post.mk.
# this should allow us to move kern.post.mk to the last line of the makefiles,
# but I'll do that slowly as I verify that one can do that w/o breaking things.
Submitted by: naddy
Any modifications to SYSTEM_OBJS after including kern.post.mk
will not make it to SYSTEM_DEP and consequently any dependency
rules. This caused __{div|rem}* to not be built...
- Add S4BIOS sleep implementation. This will works well if MIB
hw.acpi.s4bios is set (and of course BIOS supports it and hibernation
is enabled correctly).
- Add DSDT overriding support which is submitted by takawata originally.
If loader tunable acpi_dsdt_load="YES" and DSDT file is set to
acpi_dsdt_name (default DSDT file name is /boot/acpi_dsdt.aml),
ACPI CA core loads DSDT from given file rather than BIOS memory block.
DSDT file can be generated by iasl in ports/devel/acpicatools/.
- Add new files so that we can add our proposed additional code to Intel
ACPI CA into these files temporary. They will be removed when
similar code is added into ACPI CA officially.
"[...] and removes the hostcache code from standard kernels---the
code that depends on it is not going to happen any time soon,
I'm afraid."
Time to clean up.
Fix it by putting back the link of machine to sys/i386/include rather
than ../../include (aka sys/pc98/include). I had a stale machine link
on my first test.
Not sure what the "right" fix is, but this unbreaks things.
new files: kern.pre.mk, which contains most of the definitions, and
kern.post.mk, which contains most of the rules.
I've tested this on i386 and pc98. I have had feedback on the sparc64
port, but no reports from anybody on alpha, ia64 or powerpc. I
appologize in advance if I've broken you.
Reviewed by: jake, jhb, arch@
- Now that apm loadable module can inform its existence to other kernel
components (e.g. i386/isa/clock.c:startrtclock()'s TCS hack).
- Exchange priority of SI_SUB_CPU and SI_SUB_KLD for above purpose.
- Add simple arbitration mechanism for APM vs. ACPI. This prevents
the kernel enables both of them.
- Remove obsolete `#ifdef DEV_APM' related code.
- Add abstracted interface for Powermanagement operations. Public apm(4)
functions, such as apm_suspend(), should be replaced new interfaces.
Currently only power_pm_suspend (successor of apm_suspend) is implemented.
Reviewed by: peter, arch@ and audit@
booted from it when doing an installkernel.
Only change kern.bootfile from ${DESTDIR}${KODIR}/${KERNEL_KO}
to ${DESTDIR}${KODIR}.old/${KERNEL_KO}, and only when we're renaming
a booted ${DESTDIR}${KODIR}/${KERNEL_KO} kernel.
Small tweaks to kldxref may be necessary to avoid the surprising (but harm-
less) behaviour of 'kldload foo' loading foo.ko.debug instead of foo.ko if
it is present in the kernel directory.
Approved by: a week of silence on -arch
MFC after: 2 weeks
This emulates APM device node interface APIs (mainly ioctl) and
provides APM services for the applications. The goal is to support
most of APM applications without any changes.
Implemented ioctls in this commit are:
- APMIO_SUSPEND (mapped ACPI S3 as default but changable by sysctl)
- APMIO_STANDBY (mapped ACPI S1 as default but changable by sysctl)
- APMIO_GETINFO and APMIO_GETINFO_OLD
- APMIO_GETPWSTATUS
With above, many APM applications which get batteries, ac-line
info. and transition the system into suspend/standby mode (such as
wmapm, xbatt) should work with ACPI enabled kernel (if ACPI works well :-)
Reviewed by: arch@, audit@ and some guys
