Fix a NULL dereference that would occur any time an ioctl() was done, due to a
missing ipmi_enqueue_request callback. Just use the default for now, until we
decide to properly enable IPMI interrupts.
Reported by: kbowling
enough rate, the IPMI code can print large numbers of messages to the
console, such as:
ipmi0: KCS: Failed to read completion code
ipmi0: KCS error: ff
ipmi0: KCS: Failed to read completion code
ipmi0: KCS error: ff
These seem to be innocuous from a system standpoint, and the user-
space code can deal with the failures. Therefore, suppress printing
these messages to the console unless bootverbose is enabled.
Obtained from: Netflix, Inc.
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Otherwise an orderly shutdown will initiate a watchdog that will cause
a 7 minute delayed reboot *by default*, In the freebsd.org cluster's case
this often worked out be a surprise reboot a minute or two after the
machine came back up.
hw.ipmi.cycle_time is the time to wait for the power down phase of the
ipmi power cycle before falling back to either reboot or halt.
Sponsored by: Netflix
o Make hw.ipmi.on a tuneable
o Changes to keep shutdown from hanging indefinitately after the wd
would normally have been disabled.
o Add support for setting pretimeout (which fires an interrupt
some time before the actual watchdog expires)
o Allow refinement of the actions to take when the watchdog expires
o Allow special startup timeout to keep us from hanging in boot
before watchdogd is started, but after we've loaded the kernel.
Obtained From: Netflix OCA Firmware
Some BMCs support power cycling the chassis via the chassis control
command 2 subcommand 2 (ipmitool called it 'chassis power cycle'). If
the BMC supports the chassis device, register a shutdown_final handler
that sends the power cycle command if request and waits up to 10s for
it to take effect. To minimize stack strain, we preallocate a ipmi
request in the softc. At the moment, we're verbose about what we're
doing.
Sponsored by: Netflix
Set watchdog timer parameters only when they really need to be changed.
In other cases just restart the timer with single Reset command instead
of two (Set and Reset).
From one side this visually reduces amount of CPU time burned in tight
loop waiting while some slow BMC configures its watchdog hardware, that
seems to be much more complicated task then just resetting the timer.
From another side on some BMCs those slow Set commands sometimes tend to
timeout, that leads to noisy log messages and even more CPU time burned,
so avoiding them can provide even bigger bonuses.
MFC after: 2 weeks
are not permitted to sleep. Only use the IPMI watchdog with backends
which poll driver-initiated requests to meet this requirement.
In practice this means that watchdogs will no longer be used on systems
that use the SSIF backend.
Differential Revision: https://reviews.freebsd.org/D2062
MFC after: 2 weeks
particular, updates to the watchdog should no longer sleep.
- Add a new IPMI_IO_LOCK for low-level I/O access. Use this for
kcs_polled_request() and smic_polled_request().
- Add a new backend callback "ipmi_driver_request" to handle a driver
request. The new callback performs the request sychronously for KCS
and SMIC. SSIF still defers the work to the worker thread since the
worker thread sleeps during request processing anyway.
- Allocate driver requests on the stack rather than using malloc().
Differential Revision: https://reviews.freebsd.org/D1723
Tested by: scottl
MFC after: 2 weeks
further refinement is required as some device drivers intended to be
portable over FreeBSD versions rely on __FreeBSD_version to decide whether
to include capability.h.
MFC after: 3 weeks
in the future in a backward compatible (API and ABI) way.
The cap_rights_t represents capability rights. We used to use one bit to
represent one right, but we are running out of spare bits. Currently the new
structure provides place for 114 rights (so 50 more than the previous
cap_rights_t), but it is possible to grow the structure to hold at least 285
rights, although we can make it even larger if 285 rights won't be enough.
The structure definition looks like this:
struct cap_rights {
uint64_t cr_rights[CAP_RIGHTS_VERSION + 2];
};
The initial CAP_RIGHTS_VERSION is 0.
The top two bits in the first element of the cr_rights[] array contain total
number of elements in the array - 2. This means if those two bits are equal to
0, we have 2 array elements.
The top two bits in all remaining array elements should be 0.
The next five bits in all array elements contain array index. Only one bit is
used and bit position in this five-bits range defines array index. This means
there can be at most five array elements in the future.
To define new right the CAPRIGHT() macro must be used. The macro takes two
arguments - an array index and a bit to set, eg.
#define CAP_PDKILL CAPRIGHT(1, 0x0000000000000800ULL)
We still support aliases that combine few rights, but the rights have to belong
to the same array element, eg:
#define CAP_LOOKUP CAPRIGHT(0, 0x0000000000000400ULL)
#define CAP_FCHMOD CAPRIGHT(0, 0x0000000000002000ULL)
#define CAP_FCHMODAT (CAP_FCHMOD | CAP_LOOKUP)
There is new API to manage the new cap_rights_t structure:
cap_rights_t *cap_rights_init(cap_rights_t *rights, ...);
void cap_rights_set(cap_rights_t *rights, ...);
void cap_rights_clear(cap_rights_t *rights, ...);
bool cap_rights_is_set(const cap_rights_t *rights, ...);
bool cap_rights_is_valid(const cap_rights_t *rights);
void cap_rights_merge(cap_rights_t *dst, const cap_rights_t *src);
void cap_rights_remove(cap_rights_t *dst, const cap_rights_t *src);
bool cap_rights_contains(const cap_rights_t *big, const cap_rights_t *little);
Capability rights to the cap_rights_init(), cap_rights_set(),
cap_rights_clear() and cap_rights_is_set() functions are provided by
separating them with commas, eg:
cap_rights_t rights;
cap_rights_init(&rights, CAP_READ, CAP_WRITE, CAP_FSTAT);
There is no need to terminate the list of rights, as those functions are
actually macros that take care of the termination, eg:
#define cap_rights_set(rights, ...) \
__cap_rights_set((rights), __VA_ARGS__, 0ULL)
void __cap_rights_set(cap_rights_t *rights, ...);
Thanks to using one bit as an array index we can assert in those functions that
there are no two rights belonging to different array elements provided
together. For example this is illegal and will be detected, because CAP_LOOKUP
belongs to element 0 and CAP_PDKILL to element 1:
cap_rights_init(&rights, CAP_LOOKUP | CAP_PDKILL);
Providing several rights that belongs to the same array's element this way is
correct, but is not advised. It should only be used for aliases definition.
This commit also breaks compatibility with some existing Capsicum system calls,
but I see no other way to do that. This should be fine as Capsicum is still
experimental and this change is not going to 9.x.
Sponsored by: The FreeBSD Foundation
ipmi_isa_attach. This keeps unintended but harmless noise about "ipmi1"
from appearing in the boot up sequence.
Submitted by: jbh@ (suggested by)
Sponsored by: Yahoo! Inc.
to return on newer Dell hardware. Bump to 6 second timeouts until someone
has a better idea on how to handle this
Reviewed by: jhb@
MFC after: 2 weeks
Sponsored by: Yahoo! Inc.
no longer have the parent in the device tree. This causes the identify
function in ipmi_isa.c to attempt to probe and poke at the ISA IPMI interface
Move the check for ipmi_attached out of the ipmi_isa_attach function and into
the ipmi_isa_identify function. Remove the check of the device tree for
ipmi devices attached.
This probing appears to make Broadcom management firmware on Dell machines
crash and emit NMI EISA warnings at various times requiring power cycles
of the machines to restore.
Bump MAX_TIMEOUT to 6 seconds as a hack for super slow IPMI interfaces that
need longer to respond to our intial probes on startup.
Tested on Dell R410, R510, R815, HP DL160G6
This is MFC candidate for 9.2R
Reviewed by: peter
MFC after: 2 weeks
Sponsored by: Yahoo! Inc.
It is already done in SSIF interface code.
This reduces contention/spinning reported by many users.
PR: kern/172166
Submitted by: Eric van Gyzen <eric at vangyzen.net>
MFC after: 2 weeks
bits under #ifdef _KERNEL but leave definitions for various structures
defined by standards ($PIR table, SMAP entries, etc.) available to
userland.
- Consolidate duplicate SMBIOS table structure definitions in ipmi(4)
and smbios(4) in <machine/pc/bios.h> and make them available to
userland.
MFC after: 2 weeks
Starting or stopping the IPMI watchdog is rather expensive with the
current implementation as all IPMI requests are bounced via thread.
This is not viable during shutdown or dumps, and this avoids headache
in the common case that the watchdog is not enabled. The IPMI watchdog
should probably be reworked to not use a separate thread to fix this
in the case when the watchdog timer is enabled.
MFC after: 2 weeks
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
kernel for FreeBSD 9.0:
Add a new capability mask argument to fget(9) and friends, allowing system
call code to declare what capabilities are required when an integer file
descriptor is converted into an in-kernel struct file *. With options
CAPABILITIES compiled into the kernel, this enforces capability
protection; without, this change is effectively a no-op.
Some cases require special handling, such as mmap(2), which must preserve
information about the maximum rights at the time of mapping in the memory
map so that they can later be enforced in mprotect(2) -- this is done by
narrowing the rights in the existing max_protection field used for similar
purposes with file permissions.
In namei(9), we assert that the code is not reached from within capability
mode, as we're not yet ready to enforce namespace capabilities there.
This will follow in a later commit.
Update two capability names: CAP_EVENT and CAP_KEVENT become
CAP_POST_KEVENT and CAP_POLL_KEVENT to more accurately indicate what they
represent.
Approved by: re (bz)
Submitted by: jonathan
Sponsored by: Google Inc
and remove a buffer overflow:
- Remove the array of per-type dispatch functions. Instead, pass each
structure to a single callback. The callback should check the type of
each table entry to take appropriate action. This matches the behavior
of other table walkers such as for the MP Table and MADT.
- Don't attempt to save an array of string pointers for each structure
entry. Instead, just skip the strings. If this code is reused to
provide a generic SMBIOS table walker in the future we could provide
a method that looks up a specific string N for a given structure record
instead of pre-populating an array of pointers. This fixes a buffer
overflow for structure entries with more than 20 strings.
PR: kern/148546
Reported by: Spencer Minear @ McAfee
MFC after: 3 days
value is obtained by dividing it by 256, not by 2550; also,
one second is 10^9 nanoseconds, not 1800000000 nanoseconds.
- Due to rounding error, setting watchdog to a really small
timeout (<1 sec) was turning the watchdog off. It should
set the watchdog to a small timeout instead.
- Implemented error checking in ipmi_wd_event(), as required
by watchdog(9).
PR: kern/130512
Submitted by: Dmitrij Tejblum
- Additionally, check that the timeout value is within the
supported range, and if it's too large, act as required by
watchdog(9).
MFC after: 3 days
via the Linux tool.
- Add Linux shim to ipmi(4)
- Create a partitions file to linprocfs to make Linux fdisk see
disks. This file is dynamic so we can see disks come and go.
- Convert msdosfs to vfat in mtab since Linux uses that for
msdosfs.
- In the Linux mount path convert vfat passed in to msdosfs
so Linux mount works on FreeBSD. Note that tasting works
so that if da0 is a msdos file system
/compat/linux/bin/mount /dev/da0 /mnt
works.
- fix a 64it bug for l_off_t.
Grabing sh, mount, fdisk, df from Linux, creating a symlink of mtab to
/compat/linux/etc/mtab and then some careful unpacking of the Linux bmc
update tool and hacking makes it work on newer Dell boxes. Note, probably
if you can't figure out how to do this, then you probably shouldn't be
doing it :-)
for slave addressing by using left-adjusted slave addresses (i.e.
xxxxxxx0b).
- Require the low bit of the slave address to always be zero in smb(4) to
help catch broken applications.
- Adjust some code in the IPMI driver to not convert the slave address for
SSIF to a right-adjusted address. I (or possibly ambrisko@) added this in
the past to (unknowingly) work around the bug in ichsmb(4).
Submitted by: Andriy Gapon <avg of icyb.net.ua> (1,2)
MFC after: 1 month
Use the much simpler cdevpriv for per-fd state and enable it. This allows
multiple opens of /dev/ipmi0 (e.g. using ipmitool while ipmievd is running
in the background).
MFC after: 1 week
to kproc_xxx as they actually make whole processes.
Thos makes way for us to add REAL kthread_create() and friends
that actually make theads. it turns out that most of these
calls actually end up being moved back to the thread version
when it's added. but we need to make this cosmetic change first.
I'd LOVE to do this rename in 7.0 so that we can eventually MFC the
new kthread_xxx() calls.
config info. from device.hints. Some machines have ipmi controllers
that do not have attachment info in either PCI, SMBIOS or ACPI.
This idea was hacked together by me and then done properly by
jhb.
Submitted by: jhb
Reviewed by: jhb (man page)
Approved by: re (Ken Smith)
MFC after: 1 week
watchdog might hide the succesful arming of an earlier one. Accept that on
failing to arm any watchdog (because of non-supported timeouts) EOPNOTSUPP is
returned instead of the more appropriate EINVAL.
MFC after: 3 days
behave as expected.
Also:
- Return an error if WD_PASSIVE is passed in to the ioctl as only
WD_ACTIVE is implemented at the moment. See sys/watchdog.h for an
explanation of the difference between WD_ACTIVE and WD_PASSIVE.
- Remove the I_HAVE_TOTALLY_LOST_MY_SENSE_OF_HUMOR define. If you've
lost your sense of humor, than don't add a define.
Specific changes:
i80321_wdog.c
Don't roll your own passive watchdog tickle as this would defeat the
purpose of an active (userland) watchdog tickle.
ichwd.c / ipmi.c:
WD_ACTIVE means active patting of the watchdog by a userland process,
not whether the watchdog is active. See sys/watchdog.h.
kern_clock.c:
(software watchdog) Remove a check for WD_ACTIVE as this does not make
sense here. This reverts r1.181.
