The pre-11n calculations include SIFS, but the 11n ones don't.
The reason is that (mostly) the 11n hardware is doing the SIFS calculation
for us but the pre-11n hardware isn't. This means that we're over-shooting
the times in the duration field for non-11n frames on 11n hardware, which
is OK, if not a little inefficient.
Now, this is all fine for what the hardware needs for doing duration math
for ACK, RTS/CTS, frame length, etc, but it isn't useful for doing PHY
duration calculations. Ie, given a frame to TX and its timestamp, what
would the end of the actual transmission time be; and similar for an
RX timestamp and figuring out its original length.
So, this adds a new field to the duration routines which requests
SIFS or no SIFS to be included. All the callers currently will call
it requesting SIFS, so this /should/ be a glorious no-op. I'm however
planning some future work around airtime fairness and positioning which
requires these routines to have SIFS be optional.
Notably though, the 11n version doesn't do any SIFS addition at the moment.
I'll go and tweak and verify all of the packet durations before I go and
flip that part on.
Tested:
* AR9330, STA mode
* AR9330, AP mode
* AR9380, STA mode
Right now the only way to force a cold reset is:
* The HAL itself detects it's needed, or
* The sysctl, setting all resets to be cold.
Trouble is, cold resets take quite a bit longer than warm resets.
However, there are situations where a cold reset would be nice.
Specifically, after a stuck beacon, BB/MAC hang, stuck calibration results,
etc.
The vendor HAL has a separate method to set the reset reason (which is
how HAL_RESET_BBPANIC gets set) which informs the HAL during the reset path
why it occured. This is almost but not quite the same; I may eventually
unify both approaches in the future.
This commit just extends HAL_RESET_TYPE to include both status (eg BBPANIC)
and type (eg do COLD.) None of the HAL code uses it yet though; that'll
come later.
It also is a big no-op in each HAL - I need to go teach each of the HALs
about cold/warm reset through this path.
rathe than private in each HAL module.
Whilst here, modify ath_hal_private to always have the per-channel
noisefloor stats, rather than conditionally. This just makes
life easier in general (no strange ABI differences between different
HAL compile options.)
Add a couple of methods (clear/reset, add) rather than using
hand-rolled versions of things.
ath kernel module:
sys/dev/ath/ath_hal/ar5212/ar5212_reset.c:2642:7: error: taking the absolute value of unsigned type 'unsigned int' has no effect [-Werror,-Wabsolute-value]
if (abs(lp[0] * EEP_SCALE - target) < EEP_DELTA) {
^
sys/dev/ath/ah_osdep.h:74:18: note: expanded from macro 'abs'
#define abs(_a) __builtin_abs(_a)
^
sys/dev/ath/ath_hal/ar5212/ar5212_reset.c:2642:7: note: remove the call to '__builtin_abs' since unsigned values cannot be negative
sys/dev/ath/ah_osdep.h:74:18: note: expanded from macro 'abs'
#define abs(_a) __builtin_abs(_a)
^
1 error generated.
This warning occurs because both lp[0] and target are unsigned, so the
subtraction expression is also unsigned, and calling abs() is a no-op.
However, the intention was to look at the absolute difference between
the two unsigned quantities. Introduce a small static function to
clarify what we're doing, and call that instead.
Reviewed by: adrian
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D1212
in the HAL. That's very memory hungry (32k just for channel statistics)
which would be better served by keeping a summary in the ANI state.
Or, later, keep a survey history in net80211.
So:
* Migrate the ah_chansurvey array to be a single entry, for the current
channel.
* Change the ioctl interface and ANI code to just reference that.
* Clear the ah_chansurvey array during channel reset, both in the AR5212
and AR5416 reset path.
at least until I can root cause what's going on.
The only platform I've seen this on is the AR9220 when attached to
the AR71xx CPUs. I get immediate PCIe bus errors and all subsequent
accesses cause further MIPS bus exceptions. I don't have any other
big-endian platforms to test this on.
If I get a chance (or two), I'll try to whack this on a bus analyser
and see exactly what happens.
I'd rather leave this on, especially for slower, embedded platforms.
But the #ifdef hell is something I'm trying to avoid.
The final missing bit here is enabling the PCI configuration register
read, but there's currently no glue available for the HAL to read (and
write) PCI configuration space registers.
Obtained from: Atheros
that generates a fatal bus trap. Normally, the chips are setup to do
128 byte DMA bursts, but when on this CPU, they can only safely due
4-byte DMA bursts due to this bug. Details of the exact nature of the
bug are sketchy, but some can be found at
https://forum.openwrt.org/viewtopic.php?pid=70060 on pages 4, 5 and 6.
There's a small performance penalty associated with this workaround,
so it is only enabled when needed on the Atheros AR71xx platforms.
Unfortunately, this condition is impossible to detect at runtime
without MIPS specific ifdefs. Rather than cast an overly-broad net
like Linux/OpenWRT dues (which enables this workaround all the time on
MIPS32 platforms), we put this option in the kernel for just the
affected machines. Sam didn't like this aspect of the patch when he
reviewed it, and I'd love to hear sane proposals on how to fix it :)
Reviewed by: sam@
o add ah_configPCIE and ah_disablePCIE for drivers to configure PCIE
power save operation (modeled after ath9k, may need changes)
o add private state flag to indicate if device is PCIE (replaces private
hack in 5212 code)
o add serdes programming ini bits for 5416 and later parts and setup
for each part (5416 and 9160 logic hand-crafted from existing routines);
5212 remains open-coded but is now hooked in via ah_configPCIE
o add PCIE workaround gunk
o add ar5416AttachPCIE for iodomatic code used by 5416 and later parts
o remove HAL_CHANNEL; convert the hal to use net80211 channels; this
mostly involves mechanical changes to variable names and channel
attribute macros
o gut HAL_CHANNEL_PRIVATE as most of the contents are now redundant
with the net80211 channel available
o change api for ath_hal_init_channels: no more reglass id's, no more outdoor
indication (was a noop), anM contents
o add ath_hal_getchannels to have the hal construct a channel list without
altering runtime state; this is used to retrieve the calibration list for
the device in ath_getradiocaps
o add ath_hal_set_channels to take a channel list and regulatory data from
above and construct internal state to match (maps frequencies for 900MHz
cards, setup for CTL lookups, etc)
o compact the private channel table: we keep one private channel
per frequency instead of one per HAL_CHANNEL; this gives a big
space savings and potentially improves ani and calibration by
sharing state (to be seen; didn't see anything in testing); a new config
option AH_MAXCHAN controls the table size (default to 96 which
was chosen to be ~3x the largest expected size)
o shrink ani state and change to mirror private channel table (one entry per
frequency indexed by ic_devdata)
o move ani state flags to private channel state
o remove country codes; use net80211 definitions instead
o remove GSM regulatory support; it's no longer needed now that we
pass in channel lists from above
o consolidate ADHOC_NO_11A attribute with DISALLOW_ADHOC_11A
o simplify initial channel list construction based on the EEPROM contents;
we preserve country code support for now but may want to just fallback
to a WWR sku and dispatch the discovered country code up to user space
so the channel list can be constructed using the master regdomain tables
o defer to net80211 for max antenna gain
o eliminate sorting of internal channel table; now that we use ic_devdata
as an index, table lookups are O(1)
o remove internal copy of the country code; the public one is sufficient
o remove AH_SUPPORT_11D conditional compilation; we always support 11d
o remove ath_hal_ispublicsafetysku; not needed any more
o remove ath_hal_isgsmsku; no more GSM stuff
o move Conformance Test Limit (CTL) state from private channel to a lookup
using per-band pointers cached in the private state block
o remove regulatory class id support; was unused and belongs in net80211
o fix channel list construction to set IEEE80211_CHAN_NOADHOC,
IEEE80211_CHAN_NOHOSTAP, and IEEE80211_CHAN_4MSXMIT
o remove private channel flags CHANNEL_DFS and CHANNEL_4MS_LIMIT; these are
now set in the constructed net80211 channel
o store CHANNEL_NFCREQUIRED (Noise Floor Required) channel attribute in one
of the driver-private flag bits of the net80211 channel
o move 900MHz frequency mapping into the hal; the mapped frequency is stored
in the private channel and used throughout the hal (no more mapping in the
driver and/or net80211)
o remove ath_hal_mhz2ieee; it's no longer needed as net80211 does the
calculation and available in the net80211 channel
o change noise floor calibration logic to work with compacted private channel
table setup; this may require revisiting as we no longer can distinguish
channel attributes (e.g. 11b vs 11g vs turbo) but since the data is used
only to calculate status data we can live with it for now
o change ah_getChipPowerLimits internal method to operate on a single channel
instead of all channels in the private channel table
o add ath_hal_gethwchannel to map a net80211 channel to a h/w frequency
(always the same except for 900MHz channels)
o add HAL_EEBADREG and HAL_EEBADCC status codes to better identify regulatory
problems
o remove CTRY_DEBUG and CTRY_DEFAULT enum's; these come from net80211 now
o change ath_hal_getwirelessmodes to really return wireless modes supported
by the hardware (was previously applying regulatory constraints)
o return channel interference status with IEEE80211_CHANSTATE_CWINT (should
change to a callback so hal api's can take const pointers)
o remove some #define's no longer needed with the inclusion of
<net80211/_ieee80211.h>
Sponsored by: Carlson Wireless
