A10/A20 SoC. Based loosely on the submitters NetBSD driver, tested on
Cubieboard 2. Playback and capture are supported.
Submitted by: Jared McNeill <jmcneill@invisible.ca>
Differential Revision: https://reviews.freebsd.org/D5202
least the audio codec driver currently in review.
Submitted by: Jared McNeill <jmcneill@invisible.ca>
Differential Revision: https://reviews.freebsd.org/D5050
Marvell twsi part, however uses different register locations, as such split
the existing driver into Marvell and Allwinner attachments.
While here clean a few style issues.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4846
* Use the Linux compat string
* Use EARLY_DRIVER_MODULE to attach at the right time
* Add a generic A10 kernel config file
* A20 now use generic_timer
* Add two new dts files for Olimex boards
* Update our custom DTS file for A10 and A20 to use the same compatible
property names as the vendor ones.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4792
* Use the ARM PLATFORM framework
* Use ARM_INTRNG on teh A20 as it has a GICv2
* Add a method to find which Allwinner SoC we are running on
Differential Revision: https://reviews.freebsd.org/D5059
This is a stub for PMSU driver. Note that it cannot be used to set the
secondary core boot address during attach because drivers are attached
later than SI_SUB_CPU sysinit where cores are started.
Setting the boot address should be done manually in platform_mp_start_ap().
SMP is working fine with this commit and was enabled in Armada38x kernel
configuration file.
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4427
Invalid (in FreeBSD) definition of PCI controller was
replaced with another one, working in FreeBSD environment.
PCI controller's entry had to move from its parent node
so as to be recognized properly by FBSD.
PCI was enabled in kernel configuration file.
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4379
With this commit, USB 2.0 works fine on Armada38x platforms.
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4375
This commit introduces initial support for Marvell Armada38x platform.
Changes:
- Add common DTS files for Armada38x SoCs and DTS file for A388-GP
- Add ARMADA38X kernel configuration
- Add option SOC_MV_ARMADA38X and set MV_PCI_PORTS
- Add list of files to compile
- Implement get_tclk(), get_sar_value(), cpu_reset() functions
- Add CPU ID and SoC numbers
- Correct ifdefs in arm/mv/timer.c
Reviewed by: ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4210
Including arm/mv/gpio.c now depends on 'gpio' device. 'device gpio' was
added to all kernconf files of Marvell boards, except ARMADAXP (dummy
mv_gpio_res definition was removed) and ARMADA38X (not supported yet).
This commit allows to use generic files.mv on A38X.
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4372
Current functionality is somewhat limited: driver assumes that there
is only one active IPU unit (IPU1) and that video output is DI0 and
video mode is 1024x768. For more advanced functionality driver requires
proper clock management which is work in progress. At the moment driver
assumes that pixel clock is configured by u-boot for 1026x768 mode.
Reviewed by: andrew, ian, mmel
Differential Revision: https://reviews.freebsd.org/D4168
Zybo needs its own DTB and has a different PHY, so add it to
the base kernel. Details on building bootable SD images at
http://www.thomasskibo.com/zedbsd/
Submitted By: Thomas Skibo
since it isn't used for my application. Add back the md device since
it's needed for NanoBSD support. Add in many of the small memory
footprint options from the access points.
With these changes we go from having ~8MB to having ~20MB free,
though free + inactive only goes from ~35MB to ~42MB. We can
also boot a nanobsd image mostly (I had to hand tweak what was
built to represent the final goal).
Move the FDT stuff to the top. We're almost ready to pull the trigger
to moving over to FDT, but something in the MCI driver is freaking out
when we do and that needs fixing first.
as of r288992 use it to manage the CCNT.
Use the CNNT for get_cyclecount() instead of binuptime() when device pmu
is compiled in; if it fails to attach, fall back to the former method.
Enable by default for the BeagleBoneBlack configuration.
Optained from: Cambridge/L41
Sponsored by: DARPA/AFRL
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D3837
driver. This is taken from the MAC at boot, but can be overridden with
'options AT91_MACB_USE_RMII'.
Switch to macb for HL201 and SAM9G20EK boards. It now works both
places. Also start to sneak up on FDT for the SAM9G20EK board, but
leave disabled due to issues with MMC that haven't been resolved.
Add early debug support for the SAM9G20EK since that is required
for FDT to work presently on these SoC.
This commit introduces support for etherswitch devices that utilize SMI as
a way of accessing its registers. SMI register is located in address space
of mge -- access to it was exported through MDIO interface.
Attachment functions were enhanced so as to ensure proper initialisation
in both cases: 1) PHYs attached directly to mge, 2) PHYs attached to
switch device and switch attached to mge. Attachment of etherswitch device
depends on dts entry with compatible="mrvl,sw" property. If none is found,
typical PHY attachment procedure follows.
In case of switch attached, PHYs' status and configuration is accessible
via etherswitchcfg, and ifconfig shows always-up, non-configurable mge
interfaces.
Due to the fact that there may be simultaneous accessess to SMI
registers (e.g. from PHY attached to one of mge instances and switch
to the other), SMI access interlock was added. It is SX lock,
because sleep ability is necessary -- busy-waiting would result
in poor performance due to long delays required by hardware.
Underlying switch driver is obliged to use sleepable locks as well.
Reviewed by: adrian
Obtained from: Semihalf
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D3900
interrupt controller.
The latter is required for INTRNG, because of the hardware erratum
workaround installed by the linux folks into the imx6 FDT data, which remaps
an ethernet interrupt to the gpio device. In the non-INTRNG world we
intercept the call to map the interrupt and map it back to the ethernet
hardware (because we don't need linux's workaround), but in the INTRNG world
we lose the hookpoint where that remapping was happening, but we gain the
ability to work the way linux does by having the gpio driver dispatch the
interrupt.
kernel configuration to A20.
There are other boards (namely the banana pi) that use exactly the same
devices.
Additionally, we are moving from static FDT support (DTB compiled
in-kernel) to DTB passed to kernel by the boot loader (ubldr). The u-boot
for these boards are already available on ports and as the crochet support
for these boards isn't committed yet, this should not bring any issues.
Discussed with: ian
This config is already building all modules, so we don't need the
MODULES_EXTRA definition. It was also causing problems to users who
rely on MODULES_OVERRIDE to do the right thing.
Discussed with: ian
in lockstat.ko. This means that lockstat probes now have typed arguments and
will utilize SDT probe hot-patching support when it arrives.
Reviewed by: gnn
Differential Revision: https://reviews.freebsd.org/D2993
The Allwinner SoC has an AHCI device on its internal main bus rather
than the PCI bus. This SoC is somewhat underdocumented, and its SATA
controller is no exception. The methods to support this chip were
harvested from the Linux Allwinner SDK, and then constants invented to
describe what's going on based on low-level constants contained in the
SATA standard and guess work.
This SoC requires a specific AHCI channel setup in order to start the
operations on the channel properly.
Clock setup and AHCI channel setup idea came from NetBSD.
Tested on Cubieboard 2 and Banana pi (and attachment on Cubieboard by
Pratik Singhal).
Differential Revision: https://reviews.freebsd.org/D737
Submitted by: imp
Reviewed by: imp, ganbold, mav, andrew
- Add driver for TDA19988 HDMI framer
- Add simple interface to communicate with HDMI sink: read EDID and set videomode
- Add event-based API to notify LCD controller when HDMI sink is available
- Add HDMI framer node and add refernce to it to lcdc node. This part of
DTS tree is custom and does not match Linux DTS because Linux uses
combination of pseudo-node in DTS and hardcoded driver information
that does not map to our model.
This will require for AArch64 as we dont have modules yet.
Sponsored by: HEIF5
Sponsored by: ARM Ltd.
Differential Revision: https://reviews.freebsd.org/D1997
BREAK_TO_DEBUGGER if they have a serial console (most do). A burst of
serial line noise (such as unplugging a usb serial adapter) can look like
a break and drop a working system into the debugger. The alt break sequence
(<CR>~^B) works fine on both serial and non-serial consoles.
based device.
Following u-boot commands allow FreeBSD boot on
Yiyate Android TV Box (aml8726-m3):
tv open 480p
mmc rescan 0
fatload mmc 0 0x80100000 kernel.bin
go 0x80100000
The current FreeBSD driver doesn't program the video
clocks so the u-boot tv command is necessary in order
for the frame buffer to be useful (otherwise it can
be skipped).
The SD card for the Yiyate Android TV Box doesn't need
anything special beyond creating a FAT16 and a UFS
filesystem.
Differential Revision: https://reviews.freebsd.org/D2636
Submitted by: John Wehle
files to vendor-provided ones. It should make easier to adopt platform
code to new revisions of hardware and to use DTS overlays for various
Beaglebone extensions (shields/capes).
Original dts filenames were not changed, they're now wrappers over dts
files provided by TI. So make sure you update .dtb files on your
devices as part of kernel update
GPIO addressing was changed: instead of one global /dev/gpioc0 there
are per-bank instances of /dev/gpiocX. Each bank has 32 pins so for
instance pin 121 on /dev/gpioc0 in old addressing scheme is now pin 25
on /dev/gpioc3
On Pandaboard serial console devices was changed from /dev/ttyu0 to
/dev/ttyu2 so you'll have to update /etc/ttys to get login prompt
on serial port in multiuser mode. Single user mode serial console
should work as-is
Differential Revision: https://reviews.freebsd.org/D2146
Reviewed by: rpaulo, ian, Michal Meloun, Svatopluk Kraus
This is based on the patch sent by Alexander Fedorov with the following
fixes/improvements:
- Better error handling;
- Clock is derived from PLL6 (obtained from netbsd);
- No more unnecessary busy loops on interrupt handler;
- style(9) fixes and code cleanup.
I also want to thanks Martin Galvan who has sent an alternative
implementation with some interesting fixes.
Tested on CubieBoard2, Banana-Pi (thanks to netgate!) and Cubieboard1
(Pratik Singhal).
This is intended to pave the way for the upcoming GSoC work (and make
easier the build of images for the supported boards).
PR: 196081
Submitted by: Alexander Fedorov <alexander.fedorov@rtlservice.com>
of AML8726 and into board specific config files since some boards
(e.g. YYHD18) use the aml8726-m3 which only have a single core.
r283057 applied most of D2432, however while it removed SMP from
AML8726, it missed adding the SMP option to the board specific
config files.
Differential Revision: https://reviews.freebsd.org/D2589
Submitted by: John Wehle
we have both the Amlogic pic and a GIC. This may be the case in some
configurations.
Differential Revision: https://reviews.freebsd.org/D2432
Submitted by: John Wehle <john@feith.com>
The Alpine Platform-On-Chip offers multicore processing
(quad ARM Cortex-A15), 1/10Gb Ethernet, SATA 3, PCI-E 3,
DMA engines, Virtualization, Advanced Power Management and other.
This code drop involves basic platform support including:
SMP, IRQs, SerDes, SATA. As of now it is missing the PCIe support.
Part of the functionality is provided by the low-level code (HAL)
delivered by the chip vendor (Annapurna Labs) and is a subject to
change in the future (is planned to be moved to sys/contrib directory).
The review log for this commit is available here:
https://reviews.freebsd.org/D2340
Reviewed by: andrew, ian, imp
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Of note:
- This commit adds native FreeBSD/arm release build support without
requiring out-of-tree utilities.
- Part of this merge removes the WANDBOARD-{SOLO,DUAL,QUAD} kernel
configuration files, for which the IMX6 kernel configuration file
should be used instead.
- The resulting images have a 'freebsd' user (password 'freebsd'),
to allow ssh(1) access when console access is not available (VGA
or serial). The default 'root' user password is set to 'root'.
- The /etc/ttys file for arm images now enable both ttyv0 and ttyu0
by default.
Help from: many (boot testing, feedback, etc.)
Sponsored by: The FreeBSD Foundation
since it supports all of these board variants.
While here, remove the WANDBOARD-{QUAD,SOLO,DUAL} kernel
configuration files.
Discussed with: ian
Sponsored by: The FreeBSD Foundation
each of the existing kernel configs. This gives a place to put config
that applies to the entire arch.
Add the ARM_NEW_PMAP option to std.armv6. This is working well in early
testing and it's time for wide exposure, but it's still nice to be able
to fall back to the old implementation for testing when a problem comes
along. Eventually the option and the old implementation will go away.
The opportunity now exists to move a whole lot of boilerplate from all the
arm kernel config files into std.arm*, but that's a commit for another day.
into the kernel, which is used mostly on early development stages.
On RPI(2) the DTB is loaded and modified by firmware and then handed to
kernel via U-Boot and ubldr.
The RPI firmware adds (or modify) a few valuable data to the in memory
DTB, like:
- System memory;
- Ethernet MAC address;
- framebuffer settings;
- Board serial and revision;
- clock-frequency for most of devices.
handles versions 0.1 and 0.2 of the standard on 32-bit ARM.
With this driver we can shutdown in QEMU. Further work is needed to
turn secondary cores on on boot and to support later revisions of the
specification.
Submitted by: Robin Randhawa <Robin.Randhawa at ARM.com>
Sponsored by: The FreeBSD Foundation
the Raspberry Pi B we support most of the devices are already supported,
however the base address has changed.
A few items are not working, or missing. The main ones are:
* DMA doesn't work in the sdhci driver.
* Enabling vchiq halts the boot, may be interrupt related.
* There is no U-Boot port yet so the DTB is embedded in the kernel.
The last point will make it difficult to boot FreeBSD, however there is
support for the Raspberry Pi 2 in the U-Boot git repo. As I have not tested
this it is left as an open task to create a port to build.
X-MFC: When the above issues are fixed
Sponsored by: ABT Systems Ltd
These are left over from long ago when there was no way to load modules
on early armv6 platforms, and when there was a build problem with ahc
that has long since been fixed, and they just keep getting copy-pasted
into new configs.
driver on Rockchip boards. It currently supports PIO mode
and dma mode needs external dma controller to be used.
Submitted by: jmcneill
Approved by: stas (mentor)
To cut off the power we need to start the shutdown sequence by writing
the OFF bit on PMIC.
Once the PMIC is programmed the SoC needs to toggle the PMIC_PWR_ENABLE
pin when it is ready for the PMIC to cut off the power. This is done by
triggering the ALARM2 interrupt on SoC RTC.
The RTC driver only works in power management mode which means it won't
provide any kind of time keeping functionality. It only implements a way
to trigger the ALARM2 interrupt when requested.
Differential Revision: https://reviews.freebsd.org/D1489
Reviewed by: rpaulo
MFC after: 2 weeks
which means that the NFSCLIENT and NFSSERVER
kernel options will no longer work. This commit
only removes the kernel components. Removal of
unused code in the user utilities will be done
later. This commit does not include an addition
to UPDATING, but that will be committed in a
few minutes.
Discussed on: freebsd-fs
o Move similar block/networking methods to common file
o Follow r275640 and correct MMIO registers width
o Pass value to MMIO platform_note method.
Sponsored by: DARPA, AFRL
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.
No objections from: net@
The TI watchdog timer is present on BeagleBone's. Since 2014, U-Boot
has been booting the BeagleBone with the watchdog enabled. We need to
disable it on boot to avoid a spurious reset.
The timer isn't exactly precise, but it will do as a watchdog. This
is also a reflection of the watchdog(9) API.
In the future, we could handle interrupts, but the watchdog(9) API
needs to be a bit smarter before that can happen.
Differential Revision: https://reviews.freebsd.org/D965
Reviewed by: andrew
MFC after: 1 week
Relnotes: yes
boards.
This is just intended to split the common config entries out, further
cleanup is expected.
Reviewed by: ian@, rpaulo@ (earlier version)
Differential Revision: https://reviews.freebsd.org/D731
- miibus fixes as suggested by Yonghyeon Pyun.
- enable VLAN MTU support.
- fix a few WITNESS complaints in cgem_attach().
- have cgem_attach() properly init the ifnet struct before calling
mii_attach() to fix panic when using e1000phy.
- fix ethernet address changing.
- fix transmit queue overflow handling.
- tweak receive queue handling to reduce receive overflows.
- bring out MAC statistic counters to sysctls.
- add e1000phy to config file.
- implement receive hang work-around described in reference guide.
- change device name from if_cgem to cgem to be consistent with other
interfaces.
Submitted by: Thomas Skibo <ThomasSkibo@sbcglobal.net>
Reviewed by: wkoszek, Yonghyeon PYUN <pyunyh@gmail.com>
(4 in operation), 4GB ram (3.5 usable) ARM machine.
Support covers device drivers for:
- Serial Peripheral Interface (SPI)
- Chrome Embedded Controller (EC) - SPI-based version
- XHCI and USB 3.0 dual-role device PHY
Also:
- Add support for Exynos5420 in Pad module
- Move power-related functions to separate driver --
Power Management Unit (PMU)
- Enable XHCI for Chromebook1
Special thanks to grehan@ for hardware, and to
hselasky@ for r269139.
current RADXA config. Radxa Rock (RR) boards have few types such as
RR (full version), RR Lite and some variants of RR engineering samples.
Add kernel config and FDT file for RR Lite board.
Approved by: stas (mentor)
platform code, it is expected these will be merged in the future when the
ARM code is more complete.
Until more boards can be tested only use this with the Raspberry Pi and
rrename the functions on the other SoCs.
Reviewed by: ian@
#NO_UNIVERSE. Many of these config files are important examples, but
add little to no regresive value to the intended purpose of
UNIVERSE. We now build over 120 kernels during universe. There's
really little to no value to this over building say 60 or even 30 of
them (either is still a way too big number). This is especially true
for kernels that are nothing more than including a common base and
adding a static DTB file. Start by pruning 1/3 of the arm kernels that
add little regresion value.
enabled. Also switch IMX6 to use SCHED_ULE.
The now-unreferenced WANDBOARD.common config will be deleted after giving
folks who may be including it a heads-up to switch to IMX6.
Support covers device drivers for:
- Interrupt Combiner
- gpio/pad, External Interrupts Controller (pad)
- I2C Interface
- Chrome Embedded Controller
- Chrome Keyboard
Also:
- Use new gpio dev class in EHCI driver
- Expand device tree information
The ADC has a 12bit resolution and its raw output can be read via sysctl(8)
interface.
The driver allows the setup of ADC clock, samples average and open delay
(the number of clock cycles to wait before start the conversion).
The TSC_ADC module is set in the general purpose mode (no touchscreen
support).
Tested on Beaglebone-black.
Written based on AM335x TRM.
Reviewed by: rpaulo
Approved by: adrian (mentor)
Tested by: me, Brian J. McGovern, Sulev-Madis Silber (ketas)
never actually ran on these chips (other than using SA1 support in an
emulator to do the early porting to FreeBSD long long ago). The clutter
and complexity of some of this code keeps getting in the way of other
maintenance, so it's time to go.
Quartz is a tiny module utilized Freescale VF6xx
system-on-chip and development kit produced by
Device Solutions.
Quartz is available in a form of LGA (38x38x2mm)
or as a module with high-density connectors.
Sponsored by: Device Solutions
WANDBOARD.common config, but with the freescale-specific optons and devices
all together at the bottom now. In addition to reformatting and shuffling
lines around, two new options are added because they're now known to work,
VFP and FREEBSD_BOOT_LOADER.
This config does not include any static DTB, it requires that u-boot
provide a DTB (or a custom kernel config can compile one in).
This will supercede all the existing WANDBOARD* configs, but those will
be left around for a while to help people transition their customized
configs to include this new one instead.
Add gpioled(4) to BEAGLEBONE kernel and add the description of the four
on-board leds of beaglebone-black to its DTS file.
Approved by: adrian (mentor, implicit)
This was an optimization used only by a few xscale platforms. Part of
the optimization was to create a direct map for all physical pages, and
that resulted in making multiple mappings of pages in a way that bypassed
the logic in pmap.c to handle VIVT cache aliasing. It also just generally
made the code more complex and hard to maintain for all SoCs.
Reviewed by: cognet
in effect due to r250753. That is sufficient for all SoCs with a 32 byte
cache line size. Systems with 64 byte cache lines will need the option;
that will be done in a separate commit.
Thanks to loos@ for pointing out r250753.
Make comments match parameters
Add options for early printf so we get regression build testing on it.
Add preview of options for FDT support coming soon (I hope)
this to the cache line size is required to avoid data corruption on armv4
and armv5, and improves performance on armv6, in both cases by avoiding
partial cacheline flushes for USB IO.
this to the cache line size is required to avoid data corruption on armv4
and armv5, and improves performance on armv6, in both cases by avoiding
partial cacheline flushes for USB IO.
All these configs already exist in 10-stable. A few that don't (and
thus can't be MFC'd yet) will be committed separately.
in the dts source, and adding the right devices to the kernel config. Also
generally bring the kernel config into line with what we have for other
Marvell/Kirkwood systems (add lots of useful devices and options).
One particularly notable addition amongst the kernel config changes is
USB_HOST_ALIGN=32, which may help eliminate data corruption on USB drives.
PR: kern/181975 arm/162159
include it accordingly. The build machinery for universe and tinderbox
tries to build every kernel config whose name begins and ends with [A-Z0-9]
and the common include file that has most of the options isn't buildable
by itself, so the new lowercase .common will avoid building it.
The MMCHS hardware is pretty much a standard SDHCI v2.0 controller with a
couple quirks, which are now supported by sdhci(4) as of r254507.
This should work for all TI SoCs that use the MMCHS hardware, but it has
only been tested on AM335x right now, so this enables it on those platforms
but leaves the existing ti_mmchs driver in place for other OMAP variants
until they can be tested.
This initial incarnation lacks DMA support (coming soon). Even without it
this improves performance pretty noticibly over the ti_mmchs driver,
primarily because it now does multiblock IO.
Add support for A20 timer.
Correct interrupt offset depending from chip.
Add basic code for CPU configuration module.
For now, add kernel config and dts file
(only FDT blob related problem needs to be solved later in
order to have one kernel for both cubieboard1 and 2).
Approved by: ray@
* Make Yarrow an optional kernel component -- enabled by "YARROW_RNG" option.
The files sha2.c, hash.c, randomdev_soft.c and yarrow.c comprise yarrow.
* random(4) device doesn't really depend on rijndael-*. Yarrow, however, does.
* Add random_adaptors.[ch] which is basically a store of random_adaptor's.
random_adaptor is basically an adapter that plugs in to random(4).
random_adaptor can only be plugged in to random(4) very early in bootup.
Unplugging random_adaptor from random(4) is not supported, and is probably a
bad idea anyway, due to potential loss of entropy pools.
We currently have 3 random_adaptors:
+ yarrow
+ rdrand (ivy.c)
+ nehemeiah
* Remove platform dependent logic from probe.c, and move it into
corresponding registration routines of each random_adaptor provider.
probe.c doesn't do anything other than picking a specific random_adaptor
from a list of registered ones.
* If the kernel doesn't have any random_adaptor adapters present then the
creation of /dev/random is postponed until next random_adaptor is kldload'ed.
* Fix randomdev_soft.c to refer to its own random_adaptor, instead of a
system wide one.
Submitted by: arthurmesh@gmail.com, obrien
Obtained from: Juniper Networks
Reviewed by: obrien
