It closed the wrong device (usually the B partition instead of the C
partition).
It closed a device without having opened it.
It didn't open a device often enough. This caused swap partitions on
slices other than the first slice looked at to be unavailable for swapping.
It didn't check the device number sufficiently.
notice, performed all of the structural changes necessary to get this thing
to work with the unidirectional-DMA version of voxware.
This work is -not- complete, but it's in far better shape than it was, and
I may not touch it again for another few months.
The ``flags 1'' in the fdc line is now only needed for owners of an
Insight tape (perhaps there aren't any? Mine is disfunctional). All
other probes are safe wrt. to the motor-control line of floppy disk
drives. Document the flag in LINT finally.
to be `int' or smaller and some functions returned `int' instead
of `void'. The first bug was detected when console functions were
defined in a place central enough for type checking to actually
work and the second bug was introduced when the interface was
changed to match what the console functions in other drivers actually
return.
through the use of the config file flags as opposed to the option
"NSECS_MULTI". "NSECS_MULTI" has been removed from the driver.
The new capability allows boot-time modification of the config.
I made the changes I sent you before. In the interests of cleanliness, I made
modifications to /sys/i386/isa/tw.c to kill the warnings and make it compile
clean. While I was at it, I also made a bunch of internal functions static.
Submitted by: Gene Stark <gene@starkhome.cs.sunysb.edu>
higher level scsi code.
Spls should never be conditionalized, so don't do so here.
Restructure the get_ccb routine so that we can't get into an infinite
loop if the ccbs are exhausted and we are are called with SCSI_NOSLEEP set.
Other driver maintainer's that based their ccb allocation routines on Julian's
code should look at these changes and implement them for their driver.
Submitted by: John Dyson
Previously, this worked right if both AUTO_EOI_1 and AUTO_EOI_2 are
defined, but not if AUTO_EOI_1 is defined and AUTO_EOI_2 is not defined.
The latter case should be the default. DUMMY_NOPS should be the default
too. Currently there are only two NOPs slowing down rtcin() (although
there are no delays in writertc()) and several FASTER_NOPs slowing down
interrupt handling in vector.s.
Fix stack offsets for the (previously) unused untested
FAST_INTR_HANDLER_USES_ES case.
This should NOT go into 2.0.5 /phk
Support disk slices. This involves mainly replacing inline code with
function calls. Support for ST506 drives is temporarily broken since
the `setgeom' arg to dsopen() is not implemented completely enough to
use. The `setgeom' arg will go away and ST506 drives will be supported
in another way. A large amount of dead code is left in wdopen() as a
reminder of the problems here.
Close the device in wdsize(). Open tracking was broken on all drives
with a swap device.
Remove support for soft write protection. There are no ioctls to set
it. It was used to disable writing to unlabelled disks, but we want
to support writing to foreign partitions on unlabeled disks.
Use generic dkbad routines to do about 2/3 of the work for supporting
bad144.
Improve disk statistics: estimate 4MB/sec instead of 8MB/sec for
the transfer rate (ISA max is 4MB/sec, old IDE max is 3.3MB/sec);
fix dk_xfer[] (it counted sectors, not transfers); keep the estimate
dk_seek[] = dk_xfer[] (was sectors, is now transfers); only count
words actually transferred (the count is still too high after a
failed write and after retries). Remove wdxfer[].
Fix indentation in wdattach(). Fix resulting botched printing of the
disk size for ST506 drives. Print the disk geometry less cryptically.
Dropping into the debugger when a break comes down the serial line is a
>MISFEATURE (1st class)< and has been put under it's own #ifdef. This
should be a magic sequence of chars instead.
